Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thin electrolyte”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

FCET Solid Oxide Fuel Cell Testing and Development (CRADA 526) (Final Report)

Pacific Northwest National Laboratory (PNNL) tested electrolyte coatings from Fuel Cell Enabling Technologies, Inc. (FCET) for use in solid oxide fuel cells (SOFCs). The key technology held by FCET is a process to deposit thin layers of oxide materials, less than 1 μm in thickness. The range of possible materials that can be deposited with their method is broad, but this project focused on the gadolinium-doped ceria (GDC) and yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight electrolyte membranes have been a long-sought target in SOFC research. The thinner the electrolyte, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). A YSZ thickness of 1 μm would be a step change from the state-of-the-art, tape-cast electrolytes (~10 μm). An in-house prototype SOFC stack from FCET was first tested. The sealing geometry of the prototype stack was determined to be problematic, and testing shifted to button cells. Anode-supported solid oxide electrolysis cell (SOEC) button cells without an electrolyte layer were produced at PNNL and sent to FCET for coating with electrolyte. Three cells were tested with a gadolinium-doped ceria (GDC) electrolyte applied via spin coating. GDC was chosen for its conductivity at lower temperatures than YSZ. All three cells failed during initial reduction under hydrogen at 600°C. Testing then shifted to YSZ, which is the standard SOFC electrolyte. Several button cells were coated with YSZ and examined with scanning electron microscopy (SEM). A promising coating of ~1 mm thickness was observed under SEM. A similarly coated button cell was tested and failed similarly to previous tests during reduction at 600°C. The YSZ coating appeared dense and uniform in SEM analysis. The roughness of the underlying Ni/YSZ anode is on the order of 1 μm, and that may have compromised the gas-tightness of the coating. Further development is warranted to understand and refine the coating process. Thin YSZ applied via this spin-coating technique could be used as a low-cost, drop-in replacement in large-scale SOFC manufacturing processes, improving cell performance and lowering the cost per watt of SOFCs.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Impact of Nickel Ions on the Oxygen Reduction Reaction Kinetics of Pt and on Oxygen Diffusion through Ionomer Thin Films

The effects of dissolved nickel on the oxygen reduction reaction (ORR) kinetics and oxygen transport properties of perfluorosulfonic acid (PFSA) thin films were investigated using rotating disk electrode (RDE) measurements of ORR on a PFSA-coated platinum electrode. The electrochemical characterization in 0.1 M perchloric acid (HClO 4 ) with and without added Ni 2+ quantitatively measured the impact of ionic interactions between the Ni 2+ cations and sulfonate (SO 3 - ) anions on oxygen transport through the PFSA thin film. Cyclic voltammetry (CV) curves in deaerated electrolyte showed that Ni 2+ cations diffusing through the PFSA thin film interact with the Pt surface altering the hydrogen underpotential deposition and stripping processes and decreasing ORR kinetics. The RDE limiting current results point to reduced permeability of oxygen through PFSA-Ni 2+ compared to PFSA-H + . Furthermore, the results indicate that transition metals leached from Pt alloy catalyst may be detrimental not only to the intrinsic ORR kinetics of the PEFC cathode catalyst through loss of the ORR-enhancing transition metal, but may also inhibit the diffusion of oxygen to the catalytic sites and poison the ORR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1994

Composite Solid Electrolyte For Lithium Cells

Composite solid electrolyte material consists of very small particles, each coated with thin layer of Lil, bonded together with polymer electrolyte or other organic binder. Material offers significant advantages over other solid electrolytes in lithium cells and batteries. Features include high ionic conductivity and strength. Composite solid electrolyte expected to exhibit flexibility of polymeric electrolytes. Polymer in composite solid electrolyte serves two purposes: used as binder alone, conduction taking place only in AI2O3 particles coated with solid Lil; or used as both binder and polymeric electrolyte, providing ionic conductivity between solid particles that it binds together.

Peled, Emmanuel↗
NASA NTRS1994

Photocured Gelled Electrolytes For Secondary Li Cells

Class of photocured polymers exhibiting lithium-ion conductivities greater than those of well-studied polymers based on polyethylene oxide (PEO) show promise as polymeric electrolytes in rechargeable lithium cells. Increase in conductivity occasioned by use of electrolytes, coupled with amenability of electrolytes to formation into uniform thin (less than 25 micrometers thick), wide films, expected to result in cells with power densities greater than 100 W h/kg and charge/discharge rates exceeding currents equal, in amperes, to ampere-hour ratings. All-solid-state lithium batteries containing these electrolytes used as high-power, high-rate rechargeable power sources in commercial and aerospace applications.

Nagasubramanian, Ganesan↗
DOE OSTI2020

An epoxy-reinforced ceramic sheet as a durable solid electrolyte for solid state Na-ion batteries

In a conventional Na-ion battery system using liquid electrolyte, there are critical safety issues due to the instability of the liquid electrolyte. Na 3 Zr 2 Si 2 PO 12 (NASICON) solid electrolyte is a material that is sufficient to replace a liquid electrolyte as it has high ionic conductivity and thermal and electrochemical stability. However, as there is a large interfacial resistance in the NASICON solid electrolyte powder, even when used in combination with a polymer electrolyte, the advantageous effects of ceramics are not easily exhibited. In this study, we propose a top-down method of combining a polymer with a ceramic in which an ion transport channel is previously formed. In this method, a NASICON solid electrolyte is partially sintered to form ion transport channels. Then the NASICON solid electrolyte pores are filled with an epoxy polymer to increase the strength of the epoxy-NASICON composite electrolyte. This method demonstrates the possibility of our composite electrolyte being used as a thin and strong film. As a result of our methods, the ionic conductivity and thermal and electrochemical stability of NASICON were maintained, while the physical strength was enhanced by approximately 2 times. In addition, a capacity of 120 mA h g -1 and stability of 20 cycles were confirmed in a half cell with a Na 3 V 2 (PO 4 ) 3 cathode and Na metal. This method proposes a new direction for research regarding composite electrolytes created using an oxide-based solid electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2020

Investigating the Chemical Reactivity of Lithium Silicate Model SEI Layers

Silicon anodes suffer from an unstable solid electrolyte interphase (SEI) layer that contributes to undesirable capacity fade with cycling. A key part to addressing this unstable SEI formation is to examine how certain components of the SEI react with the electrolyte over time. One SEI component that has not been thoroughly studied in the context of the chemical reactivity against the electrolyte is lithiated silicate. Four model silicate thin films with increasing lithium content were deposited by radio frequency (RF) magnetron sputtering to study how the lithiation of the native oxide on a silicon anode affects the chemical stability of the anode surface. SiO2, Li2Si2O5, Li2SiO3, and Li3SiOx films were exposed to 1.2 M LiPF6 in the 3:7 wt% ethylene carbonate/ethyl methyl carbonate (EC/EMC) electrolyte for periods of time that are representative of the amount of time it takes to undergo cell formations. Soaked samples were rinsed, dried, and characterized by a combination of attenuated total reflectance-infrared spectroscopy (ATR-IR), focused ion beam-secondary electron microscopy (FIB-SEM), and X-ray photoelectron spectroscopy (XPS) depth profiling. It was found that the rate of the decrease in film thickness of the silicates exposed to the electrolyte over time increases as a function of the lithium content in the thin film. This reaction involves HF etching and LiPF6 salt degradation leading to silicate loss and fluorination throughout the bulk. Understanding this chemical instability is critical to determining the overall mechanism of SEI degradation over time.

ADVANCED PROPULSION SYSTEMS,ENERGY STORAGE↗
DOE OSTI2020

Understanding the Reactivity of a Thin Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 Solid–State Electrolyte toward Metallic Lithium Anode

The thickness of solid-state electrolytes (SSEs) significantly affects the energy density and safety performance of all-solid-state lithium batteries. However, a sufficient understanding of the reactivity toward lithium metal of ultrathin SSEs (<100 μm) based on NASICON remains lacking. Herein, for the first time, a self-standing and ultrathin (70 μm) NASICON-type Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolyte via a scalable solution process is developed, and X-ray photoelectron spectroscopy reveals that changes in LAGP at the metastable Li-LAGP interface during battery operation is temperature dependent. Severe germanium reduction and decrease in LAGP particle size are detected at the Li-LAGP interface at elevated temperature. As a result, oriented plating of lithium metal on its preferred (110) face occurs during in situ X-ray diffraction cycling.

25 ENERGY STORAGE↗
NASA NTRS2011

Effect of Reverse Bias Stress on Leakage Currents and Breakdown Voltages of Solid Tantalum Capacitors

The majority of solid tantalum capacitors are produced by high-temperature sintering of a fine tantalum powder around a tantalum wire followed by electrolytic anodization that forms a thin amorphous Ta2O5 dielectric layer and pyrolysis of manganese nitrite on the oxide to create a conductive manganese dioxide electrode. A contact to tantalum wire is used as anode terminal and to the manganese layer as a cathode terminal of the device. This process results in formation of an asymmetric Ta -- Ta2O5 -- MnO2 capacitor that has different characteristics at forward (positive bias applied to tantalum) and reverse (positive bias applied to manganese cathode) voltages. Reverse bias currents might be several orders of magnitude larger than forward leakage currents so I-V characteristics of tantalum capacitors resemble characteristics of semiconductor rectifiers. Asymmetric I-V characteristics of Ta -- anodic Ta2O5 systems have been observed at different top electrode materials including metals, electrolytes, conductive polymers, and manganese oxide thus indicating that this phenomenon is likely related to the specifics of the Ta -- Ta2O5 interface. There have been multiple attempts to explain rectifying characteristics of capacitors employing anodic tantalum pentoxide dielectrics. A brief review of works related to reverse bias (RB) behavior of tantalum capacitors shows that the mechanism of conduction in Ta -- Ta2O5 systems is still not clear and more testing and analysis is necessary to understand the processes involved. If tantalum capacitors behave just as rectifiers, then the assessment of the safe reverse bias operating conditions would be a relatively simple task. Unfortunately, these parts can degrade with time under reverse bias significantly, and this further complicates analysis of the I-V characteristics and establishing safe operating areas of the parts. On other hand, time dependence of reverse currents might provide additional information for investigation of the processes under reverse bias conditions. In practice, there were instances when, due to unforeseen events, the system operated at conditions when capacitors experience periodically a relatively small reverse bias for some time followed by normal, forward bias conditions. In such a case an assessment should be made on the degree to which these capacitors are degraded by application of low-voltage reverse bias, and whether this degradation can be reversed by normal operating conditions. In this study, reverse currents in different types of tantalum capacitors were monitored at different reverse voltages below 15%VR and temperatures in the range from room to 145 C for up to 150 hours to get better understanding of the degradation process and determine conditions favorable to the unstable mode of operation. The reversibility of RB degradation has been evaluated after operation of the capacitors at forward bias conditions. The effect of reverse bias stress (RBS) on reliability at normal operating conditions was evaluated using highly accelerated life testing at voltages of 1.5VR and 2 VR and by analysis of changes in distributions of breakdown voltages. Possible mechanisms of RB degradation are discussed.

Teverovsky, Alexander A.↗
NASA NTRSDate not supplied

Thin-Film Embedded Sensors for Battery Health Monitoring

Hybrid or all-electric aircraft are being developed as the next generation of aircraft to both allow new forms of aviation and decrease environmental impact. Since these types of aircraft are based on high-capacity battery technology, safe operation of these batteries becomes increasingly important. In particular, the potential for battery failure due to uncontrolled chemical reactions resulting in thermal runaway, catastrophic failure, and battery fires must be addressed in order for such battery technology to have the level of safety needed for standard aviation implementation. Efforts to ensure battery safety often involve engineering solutions that seek to contain rather than prevent such events by early detection. Such approaches increase the system weight and decrease the power per unit mass provided by the battery system. Existing methods for measuring battery parameters to determine the battery state-of-health are limited. These methods include electrical measurements of the cell current and/or voltage output as well as temperature measurements taken externally on the cell surface. Such external temperature measurements are limited in their ability to provide early warning of impending battery failure. In response, an effort to develop sensors operating internal to battery for health monitoring has been ongoing in the NASA Sensor-based Prognostics to Avoid Runaway Reactions & Catastrophic Ignition (SPARRCI) project. The basic approach associated with this sensor work is the deposition of thin film sensors on the battery separator located between the anode and cathode of the battery. These thin film sensors are then monitored to determine changes in battery parameters and health. Microfabrication techniques are employed to minimize the overall impact of the sensors on battery operation through the implementation of sensors with minimal size, weight, and power consumption. The thickness of the films, which are fabricated through physical vapor deposition (sputtering), are on the order of thousands of angstroms and can have minimal surface area. Thin film sensors for system health management have been implemented for a many decades on complex components for aerospace applications. However, the application of thin films of this type on a battery separator for internal battery monitoring applications has not previously been demonstrated to our knowledge. This paper describes the development of sensors for the internal battery monitoring through the use of thin film sensor technology. Thin metal films were successfully deposited on a battery separator polymer material with good adherence and electrical continuity. Multiple types of sensors have been deposited, as well as lead connections from the sensor to the edge of the separator material. The ability of these thin film sensors immersed in electrolyte to perform multiple types of battery parameter measurements has been demonstrated. For example, a multiparameter sensor system measured multiple properties simultaneously inside of a pouch cell over a wide temperature range. Further, real time measurement of interior temperature changes in a battery pouch cell with an integrated interior temperature sensor was demonstrated. These changes include detecting a fault in the battery (shorting) in situ with rapid response time (less than a minute) corresponding to a more limited response by a temperature sensor mounted externally. Other aspects of monitoring battery health were also explored, such as real-time measurement of simulated dendrite growth/metal deposition by sensor on separator material demonstrated. Future efforts will include improvements in the durability of the sensor structure to allow introduction of the approach into standard battery fabrication techniques. Overall, this work is a step forward in providing a method to prevent catastrophic battery failures and provide a foundation for safer, lighter, and higher energy batteries for the electric aircraft industry.

thin film battery health↗
DOE OSTI2022

Long–Cycling Sulfide–Based All–Solid–State Batteries Enabled by Electrochemo–Mechanically Stable Electrodes

Anode significantly determines the energy density of all-solid-state Lithium batteries (ASLBs). Silicon (Si) and Lithium (Li) metal are two of the most attractive anodes because of their ultrahigh theoretical capacities. However, most investigations focus on Li metal; the great potential of Si is underrated. This study investigates Si anode's stability, processability, and cost in ASLBs and compares them with Li metal. Moreover, the single-crystal LiNi 0.8 Co 0.1 Mn 0.1 O 2 is stabilized with a lithium silicate (Li 2 SiO x ) through a scalable sol-gel method. ASLBs with a cell-level energy density of 285 Wh kg -1 are obtained through sandwiching Si anode, thin sulfide solid-state electrolyte membrane, and interface stabilized LiNi 0.8 Co 0.1 Mn 0.1 O 2 . The full cell delivered a high capacity of 145 mAh g -1 at C/3 and maintained stability for 1000 cycles. This work inspires commercializing the ASLBs on a large scale with exciting manufacturing lines for large-scale, safe, and economical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2021

Ammonia-fed reversible protonic ceramic fuel cells with Ru-based catalyst

Abstract The intermediate operating temperatures (~400–600 °C) of reversible protonic ceramic fuel cells (RePCFC) permit the potential use of ammonia as a carbon-neutral high energy density fuel and energy storage medium. Here we show fabrication of anode-supported RePCFC with an ultra-dense (~100%) and thin (4 μm) protonic ceramic electrolyte layer. When coupled to a novel Ru-(BaO) 2 (CaO)(Al 2 O 3 ) (Ru-B2CA) reversible ammonia catalyst, maximum fuel-cell power generation reaches 877 mW cm −2 at 650 °C under ammonia fuel. We report relatively stable operation at 600 °C for up to 1250 h under ammonia fuel. In fuel production mode, ammonia rates exceed 1.2 × 10 −8 NH 3 mol cm −2 s −1 at ambient pressure with H 2 from electrolysis only, and 2.1 × 10 −6 mol NH 3 cm −2 s −1 at 12.5 bar with H 2 from both electrolysis and simulated recycling gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

Vapor-Exposure Cell For Testing Thin-Film Electrodes

Vapor-exposure test cell (VETC) designed to be used in testing thin-film electrodes on solid electrolytes electrochemically at high temperature. Use of VETC much simpler and less expensive than testing alkali-metal thermal-to-electric converter (AMTEC) fuel cell, electrolysis cell, or other entire device containing solid electrolyte and electrodes of material and configuration to be characterized.

Ryan, Margaret A.↗
NASA NTRS1995

Directly Deposited Current Collecting Grids for Alkali Metal Thermal-to-Electric Converter Electrodes

Current collection in porous thin film electrodes on solid electrolytes has been improved by using thick film grids to decrease sheet and contact resistance in RhW and PtW electrodes. The grids are directly deposited on the solid electrolyte either by sputter- or photodeposition, and the electrode deposited over the grid. Comparison of the performance of electrodes having such underlying grids with that of electrodes without such grids has shown performance, as measured by current or power produced, to be improved by 10-30% in electrodes with grids.

Ryan, M. A.↗
NASA NTRS2002

New Solid Polymer Electrolytes for Improved Lithium Batteries

The objective of this work was to identify, synthesize and incorporate into a working prototype, next-generation solid polymer electrolytes, that allow our pre-existing solid-state lithium battery to function better under extreme conditions. We have synthesized polymer electrolytes in which emphasis was placed on the temperature-dependent performance of these candidate electrolytes. This project was designed to produce and integrate novel polymer electrolytes into a lightweight thin-film battery that could easily be scaled up for mass production and adapted to different applications.

Hehemann, David G.↗
NASA NTRS1995

Directly Deposited Current Collecting Grids for AMTEC Electrodes

Current collection in porous thin film electrodes on solid electrolytes has been improved by using thick film grids to decrease sheet and contact resistance in RhW and PtW electrodes. The grids are directly deposited on the solid electrolyte, either by sputter or photodepostion, and the electrode is deposited over the grid. Comparison of the performance of electrodes having such underlying grids with that of electodes without such grids has shown performance, as measured by current or power produced, to be improved by 10-30% in electrodes with grids.

Ryan, M. A.↗
DOE OSTI2020

STRUCTURE AND PROPERTIES STUDY ON ENERGY MATERIALS: THERMOELECTRIC MATERIAL TETRAHEDRITE AND LITHIUM ION CONDUCTOR

Development of efficient energy materials is critical in order to ease the energy demand and reduce our dependence of fossil fuel. Thermoelectric materials are promising due to their capability of generating electrical power by recovering waste heat. The performance of thermoelectric materials is quantified by a dimensionless figure of merit zT, which depends on their properties such as electrical conductivity, Seebeck coefficient and thermal conductivity. Tetrahedrites, a copper antimony sulfosalt mineral, typified by Cu 12-x MxSb 4 S 13 , where M is a transition metal element such as Ni, Zn, Fe or Mn, have great potential for thermoelectric application due to their relatively high zT (close to 1 at 700 K), earth-abundance, environmental friendliness, favorable electrical properties, and most importantly intrinsic low lattice thermal conductivity (less than 1 W m -1 K -1 ) in wide temperature. In addition to energy recovery, reliable energy storage devices are also emerging to relieve the energy demand and improve the efficiency of consuming energy resources. Lithium-ion batteries are known to be reliable and successful electrochemical energy storage devices and appliable in various aspects, including laptops, smartphones and electrical vehicles. Lithium phosphorous oxynitride (LiPON) are widely used as thin-film solid-state electrolytes in Li-ion battery, which is the only demonstrated solid-state electrolyte that is quite stable in direct contact with Li metal at potentials from 0-5 V. However, the structure of LiPON, the effects of N doping, and the origin of its good electrochemical stability remains inconclusive. In this thesis, reliable modeling techniques accompanied with experimental tools, are applied to study the thermoelectric material tetrahedrite and the ionic conductor LiPON, in order to study their structural and dynamical properties. Accurate and efficient density-functional theory (DFT) and density-functional tight-binding (DFTB) methods, combined with molecular dynamics (MD) simulations are utilized in order to investigate the structures and properties of these energy materials. The incoherent and coherent atomic dynamics study of tetrahedrite Cu 10.5 NiZn 0.5 Sb 4 S 13 provides the origin of softening upon cooling by investigate the motion of Cu12e at different temperatures. The dynamic structure factors in the longitudinal and transverse direction will also be discussed. The Cu movement of Cu-rich tetrahedrite Cu 14 Sb 4 S 13 is revealed by Cu self-diffusivity, nuclear density map and “nudged elastic band” (NEB). Moreover, we investigate the effect of simulation cell size and basis sets on the DFT-based MD simulation results using tetrahedrite Cu1 0 Zn 2 Sb 4 S 13 thermoelectric as a model material, showing the advantage of larger cell by accessing smaller Q range. In addition, the low-temperature structural properties of Cu 12 Sb 4 S 13 is measured by neutron diffraction, which indicates that no cubic to tetragonal transition occurs at metal-semiconductor transition (MST) temperature. Thermoelectric properties such as Seebeck coefficient, electrical resistivity and electrical thermal conductivity will also be investigated. DFTB method is implemented to study the structure and transport properties of Li 3 PO 4 and LiPON, while the exploration of N doping effect is included. Lastly, the LiPON/Li interphase will be revealed in order to study the origin of electrochemical stability.

Li, Junchao↗
DOE OSTI2020

STRUCTURE AND PROPERTIES STUDY ON ENERGY MATERIALS: THERMOELECTRIC MATERIAL TETRAHEDRITE AND LITHIUM ION CONDUCTOR LiPON

Development of efficient energy materials is critical in order to ease the energy demand and reduce our dependence of fossil fuel. Thermoelectric materials are promising due to their capability of generating electrical power by recovering waste heat. The performance of thermoelectric materials is quantified by a dimensionless figure of merit zT, which depends on their properties such as electrical conductivity, Seebeck coefficient and thermal conductivity. Tetrahedrites, a copper antimony sulfosalt mineral, typified by Cu12-xMxSb4S13, where M is a transition metal element such as Ni, Zn, Fe or Mn, have great potential for thermoelectric application due to their relatively high zT (close to 1 at 700 K), earth-abundance, environmental friendliness, favorable electrical properties, and most importantly intrinsic low lattice thermal conductivity (less than 1 W m-1 K-1) in wide temperature. In addition to energy recovery, reliable energy storage devices are also emerging to relieve the energy demand and improve the efficiency of consuming energy resources. Lithium-ion batteries are known to be reliable and successful electrochemical energy storage devices and appliable in various aspects, including laptops, smartphones and electrical vehicles. Lithium phosphorous oxynitride (LiPON) are widely used as thin-film solid-state electrolytes in Li-ion battery, which is the only demonstrated solid-state electrolyte that is quite stable in direct contact with Li metal at potentials from 0-5 V. However, the structure of LiPON, the effects of N doping, and the origin of its good electrochemical stability remains inconclusive.In this thesis, reliable modeling techniques accompanied with experimental tools, are applied to study the thermoelectric material tetrahedrite and the ionic conductor LiPON, in order to study their structural and dynamical properties. Accurate and efficient density-functional theory (DFT) and density-functional tight-binding (DFTB) methods, combined with molecular dynamics (MD) simulations are utilized in order to investigate the structures and properties of these energy materials. The incoherent and coherent atomic dynamics study of tetrahedrite Cu10.5NiZn0.5Sb4S13 provides the origin of softening upon cooling by investigate the motion of Cu12e at different temperatures. The dynamic structure factors in the longitudinal and transverse direction will also be discussed. The Cu movement of Cu-rich tetrahedrite Cu14Sb4S13 is revealed by Cu self-diffusivity, nuclear density map and "nudged elastic band" (NEB). Moreover, we investigate the effect of simulation cell size and basis sets on the DFT-based MD simulation results using tetrahedrite Cu10Zn2Sb4S13 thermoelectric as a model material, showing the advantage of larger cell by accessing smaller Q range. In addition, the low-temperature structural properties of Cu12Sb4S13 is measured by neutron diffraction, which indicates that no cubic to tetragonal transition occurs at metal-semiconductor transition (MST) temperature. Thermoelectric properties such as Seebeck coefficient, electrical resistivity and electrical thermal conductivity will also be investigated. DFTB method is implemented to study the structure and transport properties of Li3PO4 and LiPON, while the exploration of N doping effect is included. Lastly, the LiPON/Li interphase will be revealed in order to study the origin of electrochemical stability

25 ENERGY STORAGE↗