Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “teeth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Analytical and experimental spur gear tooth temperature as affected by operating variables

A gear tooth temperature analysis was performed using a finite element method combined with a calculated heat input, calculated oil jet impingement depth, and estimated heat transfer coefficients. Experimental measurements of gear tooth average surface temperatures and instantaneous surface temperatures were made with a fast response infrared radiometric microscope. Increased oil jet pressure had a significant effect on both average and peak surface temperatures at both high load and speeds. Increasing the speed at constant load and increasing the load at constant speed causes a significant rise in average and peak surface temperatures of gear teeth. The oil jet pressure required for adequate cooling at high speed and load conditions must be high enough to get full depth penetration of the teeth. Calculated and experimental results were in good agreement with high oil jet penetration but showed poor agreement with low oil jet penetration depth.

Townsend, D. P.↗
NASA NTRS1981

Optimal tooth numbers for compact standard spur gear sets

The design of a standard gear mesh is treated with the objective of minimizing the gear size for a given ratio, pinion torque, and allowable tooth strength. Scoring, pitting fatigue, bending fatigue, and the kinematic limits of contact ratio and interference are considered. A design space is defined in terms of the number of teeth on the pinion and the diametral pitch. This space is then combined with the objective function of minimum center distance to obtain an optimal design region. This region defines the number of pinion teeth for the most compact design. The number is a function of the gear ratio only. A design example illustrating this procedure is also given.

Savage, M.↗
NASA NTRS1981

Experiment K-310: The effect of spaceflight on osteogenesis and dentinogenesis in the mandibles of rats

Normal rates of dentinogenesis and osteogenesis in the body of the mandible were observed. The total calcium, inorganic phosphorus and hydroxyproline levels in the jaws and incisors of the flight rats were normal. Gravity density fractionation studies suggested, however, that spaceflight caused a delay in the normal maturation of bone mineral and matrix; normal values were reestablished by 6 days postflight. The teeth were spared. The circadian and ultradian patterns of dentin calcification were normal during spaceflight and recovery periods, but the enamel rhythms displayed a greater amplitude of sulfur concentrations and this abnormal calcium to sulfur ratios only during exposure to zero gravity. The rat mandible and teeth do not suffer the deficits of bone formation common to weight bearing parts of the skeleton during spaceflight. The only derangements detected were in the quality of the matrix and mineral moieties.

Simmons, D. J.↗
NASA NTRS1982

Magnetic-Gear Concept for Special Applications

Proposed gear has magnetic instead of mechanical teeth. Magnetic gears consists of permanent magnets resembling mechanical gears but with smooth faces and alternating magnetic poles in place of mechanical teeth. Low torque, noncontacting gears useful in special environments.

Chandler, J. A.↗
NASA NTRS1982

Acoustic tooth cleaner

An acoustic oral hygiene unit is described that uses acoustic energy to oscillate mild abrasive particles in a water suspension which is then directed in a low pressure stream onto the teeth. The oscillating abrasives scrub the teeth clean removing food particles, plaque, calculous, and other foreign material from tooth surfaces, interproximal areas, and tooth-gingiva interface more effectively than any previous technique. The relatively low power output and the basic design makes the invention safe and convenient for everyday use in the home without special training. This invention replaces all former means of home dental prophylaxis, and requires no augmentation to fulfill all requirements for daily oral hygienic care.

Heyman, J. S.↗
NASA NTRS1981

Optimal tooth numbers for compact standard spur gear sets

The design of a standard gear mesh is treated with the objective of minimizing the gear size for a given ratio, pinion torque, and allowable tooth strength. Scoring, pitting fatigue, bending fatigue, and the kinematic limits of contact ratio and interference are considered. A design space is defined in terms of the number of teeth on the pinion and the diametral pitch. This space is then combined with the objective function of minimum center distance to obtain an optimal design region. This region defines the number of pinion teeth for the most compact design. The number is a function of the gear ratio only. A design example illustrating this procedure is also given.

Savage, M.↗
NASA NTRS1982

Experimental and analytical determination of gear tooth temperatures with oil jet lubrication

Gear tooth average and instantaneous surface temperatures were measured with a fast response infrared radiometric microscope, while operating at arious speeds, loads and oil jet pressures. Increased oil jet pressure had a significant effect on both average and peak surface temperatures at all test conditions, increasing the speed at constant load and increasing the load at constant speed causes a significant rise in average and peak surface temperatures of gear teeth. A gear tooth temperature analysis was conducted by a finite element method combined with a calculated heat input and oil jet impingment depth with estimated heat transfer coefficients based on the experimental data. It is concluded that oil jet pressures required for adequate cooling at high load and speed conditions must be high enough to get full penetration depth of the teeth.

Townsend, D. P.↗
NASA NTRS1983

Study of lubricant jet flow phenomena in spur gears: Out of mesh condition

The penetration depth onto the tooth flank of a jet of oil at different velocities pointed at the pitch line on the outgoing side of mesh was determined. The analysis determines the impingement depth for both the gear and the pinion. It includes the cases for speed increasers and decreasers as well as for one to one gear ratio. In some cases the jet will strike the loaded side of the teeth, and in others it will strike the unloaded side of the teeth. In nearly all cases the top land will be cooled regardless of the penetration depth, and postimpingement oil spray will usually provide adequate amounts of oil for lubrication but is marginal or inadequate for cooling.

Townsend, D. P.↗
NASA NTRS1982

Comparative evaluation of three shaft seals proposed for high performance turbomachinery

Experimental pressure profiles and leak rate characteristics for three shaft seal prototype model configurations proposed for the space shuttle turbopump were assessed in the concentric and fully eccentric, to point of rub, positions without the effects of rotation. The parallel-cylindrical configuration has moderate to good stiffness with a higher leak rate. It represents a simple concept, but for practical reasons and possible increases in stability, all such seals should be conical-convergent. The three-stepdown-sequential, parallel-cylindrical seal is converging and represents good to possible high stiffness when fluid separation occurs, with a significant decrease in leak rate. Such seals can be very effective. The three-stepdown-sequential labyrinth seal of 33-teeth (i.e., 12-11-10 teeth from inlet to exit) provides excellent leak control but usually has very poor stiffness, depending on cavity design. The seal is complex and not recommended for dynamic control.

Hendricks, R. C.↗
NASA NTRS1983

Effect of spaceflight on the non-weight-bearing bones of rat skeleton

The effects of weightlessness on the integrated growth and remodeling of nonweight-bearing bones (the mandibles, teeth, and ribs) were studied. Rats prelabeled with tetracycline to mark the surfaces of bone and tooth formation were subjected to spaceflight conditions for 18.5 days, followed by further injections of tetracycline on days 6 and 29 postflight.Results show that spaceflight conditions did not alter the rate of periosteal bone formation in the ribs and regions of the mandibles covered by masticatory muscles, although bone formation-calcification rates were found to be impaired at those sites in the jaw that had no contiguous muscle (molar region). The remodeling activity on the alveolar bone around the buccal roots of the molar teeth was found to be significantly reduced. While total Ca, P, and hydroxyproline concentrations in the jaws, incisors, and ribs were normal after spaceflight, it was determined that weightless conditions caused a delay in the maturation of bone mineral and matrix in the jaws. These anomalies were found to be corrected by 29 days postflight. These results indicate that most of the nonweight-bearing bones of the rat skeleton are at risk to the effects of weightlessness.

Simmons, D. J.↗
NASA NTRS1987

Non-backdriveable free wheeling coupling

A rotary coupling for connecting a driven part to a source of rotary force is described. This device transmits rotary force in one direction only and disengages to permit the driven part to free wheel when the input member is stopped and precludes the backdriving of rotary force from output member to input member. The coupling includes an input member having a splined shaft, a coupling member connected to the splined shaft, and a coaxial output member. The coupling member and the output member having complementary sets of axially facing clutch teeth. Guides in the form of helical grooves on the coupling member and spring loaded followers acting with the guides affect the engagement and disengagement of the clutch teeth by moving the coupling member toward and away from output member, the followers and guides themselves disengaging to permit free wheeling of output member when input member is stopped.

Llewellin, William R.↗
NASA NTRS1987

Tube coupling device

A first annular ring of a tube coupling device has a keyed opening sized to fit around the nut region of a male coupling, and a second annular ring has a keyed opening sized to fit around the nut of a female coupling. Each ring has mating ratchet teeth and these rings are biased together, thereby engaging these teeth and preventing rotation of these rings. This in turn prevents the rotation of the male nut region with respect to the female nut. For tube-to-bulkhead locking, one facet of one ring is notched, and a pin is pressed into an opening in the bulkhead. This pin is sized to fit within one of the notches in the ring, thereby preventing rotation of this ring with respect to the bulkhead.

Myers, William N.↗
NASA NTRS1986

Test results for sawtooth-pattern damper seals - Leakage and rotordynamic coefficients

Test results consisting of direct and transverse force coefficients are presented for eleven sawtooth-pattern damper-seal configurations. The designation 'damper' seal refers to a seal which uses a deliberately roughened stator and smooth rotor to increase the net seal damping force. The designation 'sawtooth-pattern' refers to a stator-roughness pattern whose cross section normal to the axis of the seal resembles saw teeth with the teeth direction opposing fluid motion in the direction of shaft rotation. The sawtooth pattern yields axial grooves in the stator which are interrupted by spacer elements which act as flow constrictions or 'dams'. Sawtooth-pattern seals had more damping than smooth seals but less than the round-hole-pattern seals tested previously. If damping is sacrificed, sawtooth-pattern seals can be designed to leak less than round-hole-pattern seals.

Childs, D.↗
NASA NTRS1989

Rotordynamic coefficients for stepped labyrinth gas seals

The basic equations are derived for compressible flow in a stepped labyrinth gas seal. The flow is assumed to be completely turbulent in the circumferential direction where the friction factor is determined by the Blasius relation. Linearized zeroth and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth-order pressure distribution is found by satisfying the leakage equation while the circumferential velocity distribution is determined by satisfying the momentum equations. The first order equations are solved by a separation of variables solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are presented in the form of a parametric study, since there are no known experimental data for the rotordynamic coefficients of stepped labyrinth gas seals. The parametric study investigates the relative rotordynamic stability of convergent, straight and divergent stepped labyrinth gas seals. The results show that, generally, the divergent seal is more stable, rotordynamically, than the straight or convergent seals. The results also show that the teeth-on-stator seals are not always more stable, rotordynamically, then the teeth-on-rotor seals as was shown by experiment by Childs and Scharrer (1986b) for a 15 tooth seal.

Scharrer, Joseph K.↗
NASA NTRS1989

Experimental results for labyrinth gas seals with honeycomb stators - Comparisons to smooth-stator seals and theoretical predictions

Experimental measurements are presented for the rotordynamic stiffness and damping coefficients of a teeth-on-rotor labyrinth seal with a honeycomb stator. Inlet circumferential velocity, inlet pressure, rotor speed, and seal clearance are primary variables. Results are compared to data for teeth-on-rotor labyrinth seals with smooth stators and to analytical predictions from a two-control-volume compressible flow model. The experimental results show that the honeycomb-stator configuration is more stable than the smooth-stator configuration at low rator speeds. At high rotor speeds, the stator surface does not affect stability. The theoretical model predicts the cross-coupled stiffness of the honeycomb-stator seal correctly within 25 percent of measured values. The model provides accurate predictions of direct damping for large clearance seals; however, the model predictions and test results diverge with increasing running speed. Overall, the model does not perform as well for low clearance seals as for high clearance seals.

Hawkins, Larry↗
NASA NTRS1993

Effect of extended tooth contact on the modeling of spur gear transmissions

In some gear dynamic models, the effect of tooth flexibility is ignored when the model determines which pairs of teeth are in contact. Deflection of loaded teeth is not introduced until the equations of motion are solved. This means the zone of tooth contact and average tooth meshing stiffness are underestimated and the individual tooth load is overstated, especially for heavily-loaded gears. The static transmission error and dynamic load of heavily-loaded, low-contact-ratio spur gears is compared with this effect both neglected and included. Neglecting the effect yields an underestimate of resonance speeds and an overestimate of the dynamic load.

Oswald, Fred B.↗
NASA NTRS1993

Effect of extended tooth contact on the modeling of spur gear transmissions

In some gear dynamic models, the effect of tooth flexibility is ignored when the model determines which pairs of teeth are in contact. Deflection of loaded teeth is not introduced until the equations of motion are solved. This means the zone of tooth contact and average tooth meshing stiffness are underestimated and the individual tooth load is overstated, especially for heavily-loaded gears. The static transmission error and dynamic load of heavily-loaded, low-contact-ratio spur gears is compared with this effect both neglected and included. Neglecting the effect yields an underestimate of resonance speeds and an overestimate of the dynamic load.

Lin, Hsiang H.↗
NASA NTRS1994

Computerized Inspection Of Gear-Tooth Surfaces

Method of manufacturing gears with precisely shaped teeth involves computerized inspection of gear-tooth surfaces followed by adjustments of machine-tool settings to minimize deviations between real and theoretical versions of surfaces. Thus, iterated cycles of cutting gear teeth, inspection, and adjustments help increase and/or maintain precision of subsequently manufactured gears.

Handschuh, R. F.↗