Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface codes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Comparison of CFD Predictions with Shuttle Global Flight Thermal Imagery and Discrete Surface Measurements

Surface temperature measurements from the STS-119 boundary-layer transition experiment on the space shuttle orbiter Discovery provide a rare opportunity to assess turbulent CFD models at hypersonic flight conditions. This flight data was acquired by on-board thermocouples and by infrared images taken off-board by the Hypersonic Thermodynamic Infrared Measurements (HYTHIRM) team, and is suitable for hypersonic CFD turbulence assessment between Mach 6 and 14. The primary assessment is for the Baldwin-Lomax and Cebeci-Smith algebraic turbulence models in the DPLR and LAURA CFD codes, respectively. A secondary assessment is made of the Shear-Stress Transport (SST) two-equation turbulence model in the DPLR code. Based upon surface temperature comparisons at eleven thermocouple locations, the algebraic-model turbulent CFD results average 4% lower than the measurements for Mach numbers less than 11. For Mach numbers greater than 11, the algebraic-model turbulent CFD results average 5% higher than the three available thermocouple measurements. Surface temperature predictions from the two SST cases were consistently 3 4% higher than the algebraic-model results. The thermocouple temperatures exhibit a change in trend with Mach number at about Mach 11; this trend is not reflected in the CFD results. Because the temperature trends from the turbulent CFD simulations and the flight data diverge above Mach 11, extrapolation of the turbulent CFD accuracy to higher Mach numbers is not recommended.

Wood, William A.↗
DOE OSTI2024

Phase diagram of the three-dimensional subsystem toric code

Subsystem quantum error-correcting codes typically involve measuring a sequence of noncommuting parity check operators. They can sometimes exhibit greater fault tolerance than conventional codes, which use commuting checks. However, unlike subspace codes, it is unclear if subsystem codes—in particular their advantages—can be understood in terms of ground-state properties of a physical Hamiltonian. In this paper, we address this question for the three-dimensional subsystem toric code (3D STC), as recently constructed by Kubica and Vasmer [], which exhibits single-shot error correction. Motivated by a conjectured relation between single-shot properties and thermal stability, we study the zero- and finite-temperature phases of an associated noncommuting Hamiltonian. By mapping the Hamiltonian model to a pair of 3D Z 2 gauge theories coupled by a kinetic constraint, we find various phases at zero temperature, all separated by first-order transitions: There are 3D toric code-like phases with deconfined point-like excitations in the bulk, and there are phases with a confined bulk supporting a 2D toric code on the surface when appropriate boundary conditions are chosen. The latter is similar to the surface topological order present in 3D STC. However, the similarities between the single-shot correction in 3D STC and the confined phases are only partial: they share the same sets of degrees of freedom, but they are governed by different dynamical rules. Instead, we argue that the process of single-shot error correction can more suitably be associated with a path (rather than a point) in the zero-temperature phase diagram, a perspective, which inspires alternative measurement sequences enabling single-shot error correction. Moreover, since none of the above-mentioned phases survives at nonzero temperature, the single-shot error-correction property of the code does not imply thermal stability of the associated Hamiltonian phase. Published by the American Physical Society 2024

Li, Yaodong (ORCID:0000000337421944)↗
NASA NTRS2004

Transonic Drag Prediction on a DLR-F6 Transport Configuration Using Unstructured Grid Solvers

A second international AIAA Drag Prediction Workshop (DPW-II) was organized and held in Orlando Florida on June 21-22, 2003. The primary purpose was to inves- tigate the code-to-code uncertainty. address the sensitivity of the drag prediction to grid size and quantify the uncertainty in predicting nacelle/pylon drag increments at a transonic cruise condition. This paper presents an in-depth analysis of the DPW-II computational results from three state-of-the-art unstructured grid Navier-Stokes flow solvers exercised on similar families of tetrahedral grids. The flow solvers are USM3D - a tetrahedral cell-centered upwind solver. FUN3D - a tetrahedral node-centered upwind solver, and NSU3D - a general element node-centered central-differenced solver. For the wingbody, the total drag predicted for a constant-lift transonic cruise condition showed a decrease in code-to-code variation with grid refinement as expected. For the same flight condition, the wing/body/nacelle/pylon total drag and the nacelle/pylon drag increment predicted showed an increase in code-to-code variation with grid refinement. Although the range in total drag for the wingbody fine grids was only 5 counts, a code-to-code comparison of surface pressures and surface restricted streamlines indicated that the three solvers were not all converging to the same flow solutions- different shock locations and separation patterns were evident. Similarly, the wing/body/nacelle/pylon solutions did not appear to be converging to the same flow solutions. Overall, grid refinement did not consistently improve the correlation with experimental data for either the wingbody or the wing/body/nacelle pylon configuration. Although the absolute values of total drag predicted by two of the solvers for the medium and fine grids did not compare well with the experiment, the incremental drag predictions were within plus or minus 3 counts of the experimental data. The correlation with experimental incremental drag was not significantly changed by specifying transition. Although the sources of code-to-code variation in force and moment predictions for the three unstructured grid codes have not yet been identified, the current study reinforces the necessity of applying multiple codes to the same application to assess uncertainty.

Lee-Rausch, E. M.↗
NASA NTRSDate not supplied

Parallelized Carbon Oxidation and Surface Recession Model in Direct-Simulation Monte Carlo Code, SPARTA

Ablative thermal protection system (TPS) materials for spacecraft are composites that often consist of a carbon-based reinforcement and a polymeric matrix. During Earth re-entry, they endure high-temperature oxidation and surface recession. Oxidation is an important mechanism for ablation, sometimes leading to the weakening, spallation, or failure of the oxidized fibers at the surface and in the char layer. However, more details are required including accurate material properties of the fiber microstructure, whether the fibers recede homogenously or localized at pits, and the role of pyrolysis outgassing in order to evaluate the role oxidation plays in the degradation and failure mechanisms of these materials. In this work, we demonstrate a parallelizable oxidation-driven ablation model developed for detailed, large-scale simulations in the DSMC code SPARTA. We also develop robust algorithms which handle the conservation of the surface state after an ablation step. Finally, we verify our model for both simple and more complex chemistry as well as microstructures with reaction statistics, oxidation depth calculations, and detailed visualization of oxidation-induced material recession at the microscale.

V Arias↗
NASA NTRS1998

Land Surface Temperature Measurements from EOD MODIS Data

We made more tests of the version 2.0 daily Level 2 and Level 3 Land-Surface Temperature (LST) code (PGE 16) jointly with the MODIS Science Data Support Team (SDST). After making minor changes a few times, the PGE16 code has been successfully integrated and tested by MODIS SDST, and recently has passed the inspection at the Goddard Distributed Active Archive Center (DAAC). We conducted a field campaign in the area of Mono Lake, California on March 10, 1998, in order to validate the MODIS LST algorithm in cold and dry conditions. Two MODIS Airborne Simulator (MAS) flights were completed during the field campaign, one before noon, and another around 10 pm PST. The weather condition for the daytime flight was perfect: clear sky, the column water vapor measured by radiosonde around 0.3 cm, and wind speed less than a half meter per second. The quality of MAS data is good for both day and night flights. We analyzed the noise equivalent temperature difference (NE(delta)T) and the calibration accuracy of the seven MAS thermal infrared (TIR) bands, that are used in the MODIS day/night LST algorithm, with daytime MAS data over four flat homogeneous study areas: two on Grant Lake (covered with ice and snow, respectively), one on Mono Lake, and another on the snow field site where we made field measurements. NE(delta)T ranges from 0.2 to 0.6 k for bands 42, 45, 46, and 48. It ranges from 0.8 to 1.1 K for bands 30-32. The day and night MAS data have been used to retrieve surface temperature and emissivities in these bands. A simple method to correct the effect of night thin cirrus has been incorporated into the day/night LST algorithm in dry atmospheric conditions. We compared the retrieved surface temperatures with those measured with TIR spectrometer, radiometers and thermistors in the snow test site, and the retrieved emissivity images with topographic map. The daytime LST values match well within 1 K. The night LST retrieved from MAS data is 3.3 K colder than those from field measurements most likely because of the effect of haze at night. The good agreement among the regional averaged surface temperatures obtained from LST values retrieved at different resolutions increased our confidence in the MODIS day/night LST algorithm.

Wan, Zheng-Ming↗
DOE OSTI2023

Design and construction of the MUSE permanent magnet stellarator

This paper documents the design and construction of MUSE, the world's first permanent magnet (PM) stellarator and the first quasi-axisymmetric experiment. The purpose of MUSE is to develop and assess a new way of building optimised stellarators that uses simple planar coils PMs. Our PM optimisation algorithm consists of initialising a geometry to pack dipoles densely, running the FAMUS code to minimise surface field error subject to PM constraints and applying discrete jumps to reach a physically realisable solution. FAMUS treats the PM system as a set of ideal point dipoles. From there we construct finite-volume magnet towers to be housed in 3D-printed PM holders. We describe the design of the PM holders, which were validated by laser metrology. We analyse the effects of finite permeability, sensitivity to perturbations and magnetostatic forces. An exact analytic formula for the magnetic field from a finite-volume PM tower is presented to compute PM–PM forces and stress on the PM holder. Stellarator construction is complete and experiments are underway.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Autonomous quantum error correction and fault-tolerant quantum computation with squeezed cat qubits

We propose an autonomous quantum error correction scheme using squeezed cat (SC) code against excitation loss in continuous-variable systems. Through reservoir engineering, we show that a structured dissipation can stabilize a two-component SC while autonomously correcting the errors. The implementation of such dissipation only requires low-order nonlinear couplings among three bosonic modes or between a bosonic mode and a qutrit. While our proposed scheme is device independent, it is readily implementable with current experimental platforms such as superconducting circuits and trapped-ion systems. Compared to the stabilized cat, the stabilized SC has a much lower dominant error rate and a significantly enhanced noise bias. Furthermore, the bias-preserving operations for the SC have much lower error rates. In combination, the stabilized SC leads to substantially better logical performance when concatenating with an outer discrete-variable code. The surface-SC scheme achieves more than one order of magnitude increase in the threshold ratio between the loss rate κ 1 and the engineered dissipation rate κ 2 . Under a practical noise ratio κ 1 /κ 2 = 10 -3 , the repetition-SC scheme can reach a 10 -15 logical error rate even with a small mean excitation number of 4, which already suffices for practically useful quantum algorithms.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Fuel Performance Analysis of Chromium-Coated Cladding under Burst Conditions

To reduce the oxidation of zirconium-based alloy cladding at high temperatures, accident tolerant fuel systems have been proposed. Of the concepts identified, chromium-coated cladding has been shown to slow oxidation without greatly impacting the fuel system geometry or neutronic performance. To determine how coated-cladding tubes will perform under high-temperature accident conditions, pressurized-tube burst tests have been performed using the Severe Accident Test Station at Oak Ridge National Laboratory. To begin modeling these tubes to better understand how the coating will impact cladding behavior, these burst tests were simulated with the BISON fuel performance code. Cladding tube surface temperatures for the burst test were developed by fitting thermocouple data into axial and azimuthal profiles, while pressure data were compared until cladding failure. The temperatures at failure and the pressure evolution show relatively good agreement between the simulation and experiment results. This is the first step of a larger effort to simulate the cladding deformation process under high-temperature transient conditions and assess the cladding margin to failure more accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1978

Three-dimensional canard-wing shape optimization in aircraft cruise and maneuver environments

This paper demonstrates a numerical technique for canard-wing shape optimization at two operating conditions. For purposes of simplicity, a mean surface wing paneling code is employed for the aerodynamic calculations. The optimization procedures are based on the method of feasible directions. The shape functions for describing the thickness, camber, and twist are based on polynomial representations. The primary design requirements imposed restrictions on the canard and wing volumes and on the lift coefficients at the operating conditions. Results indicate that significant improvements in minimum drag and lift-to-drag ratio are possible with reasonable aircraft geometries. Calculations were done for supersonic speeds with Mach numbers ranging from 1 to 6. Planforms were mainly of a delta shape with aspect ratio of 1.

De Silva, B. M. E.↗
NASA NTRS1982

Summary and recent results from the NASA advanced High Speed Propeller Research Program

Advanced high-speed propellers offer large performance improvements for aircraft that cruise in the Mach 0.7 to 0.8 speed regime. The current status of the NASA research program on high-speed propeller aerodynamics, acoustics, and aeroelastics is described. Recent wind tunnel results for five 8- to 10-blade advanced models are compared with analytical predictions. Test results show that blade sweep was important in achieving net efficiencies near 80 percent at Mach 0.8 and reducing near-field cruise noise by dB. Lifting line and lifting surface aerodynamic analysis codes are under development and some initial lifting line results are compared with propeller force and probe data. Some initial laser velocimeter measurements of the flow field velocities of an 8-bladed 45 deg swept propeller are shown. Experimental aeroelastic results indicate that cascade effects and blade sweep strongly affect propeller aeroelastic characteristics. Comparisons of propeller near-field noise data with linear acoustic theory indicate that the theory adequate predicts near-field noise for subsonic tip speeds but overpredicts the noise for supersonic tip speeds. Potential large gains in propeller efficiency of 7 to 11 percent at Mach 0.8 may be possible with advanced counter-rotation propellers.

Mitchell, G. A.↗
NASA NTRS1983

New test techniques and analytical procedures for understanding the behavior of advanced propellers

Analytical procedures and experimental techniques were developed to improve the capability to design advanced high speed propellers. Some results from the propeller lifting line and lifting surface aerodynamic analysis codes are compared with propeller force data, probe data and laser velocimeter data. In general, the code comparisons with data indicate good qualitative agreement. A rotating propeller force balance demonstrated good accuracy and reduced test time by 50 percent. Results from three propeller flow visualization techniques are shown which illustrate some of the physical phenomena occurring on these propellers.

Stefko, G. L.↗
NASA NTRS1984

Summary of recent NASA propeller research

Advanced high-speed propellers offer large performance improvements for aircraft that cruise in the Mach 0.7 to 0.8 speed regime. At these speeds, studies indicate that there is a 15 to near 40 percent block fuel savings and associated operating cost benefits for advanced turboprops compared to equivalent technology turbofan powered aircraft. Recent wind tunnel results for five eight to ten blade advanced models are compared with analytical predictions. Test results show that blade sweep was important in achieving net efficiencies near 80 percent at Mach 0.8 and reducing nearfield cruise noise by about 6 dB. Lifting line and lifting surface aerodynamic analysis codes are under development and some results are compared with propeller force and probe data. Also, analytical predictions are compared with some initial laser velocimeter measurements of the flow field velocities of an eightbladed 45 swept propeller. Experimental aeroelastic results indicate that cascade effects and blade sweep strongly affect propeller aeroelastic characteristics. Comparisons of propeller near-field noise data with linear acoustic theory indicate that the theory adequately predicts near-field noise for subsonic tip speeds but overpredicts the noise for supersonic tip speeds.

Mikkelson, D. C.↗
NASA NTRS1983

Stagnation-point ablation of carbonaceous flat disks. I Theory

The process of ablation is calculated for the stagnation region of a flat disk in a radiation-dominated, massive-blowing environment produced in a ballistic range filled with argon. Flow environments are determined by solving the boundary-layer equations while radiative transfer is calculated through a line-by-line spectral computation. The resulting wall heat-transfer rates are coupled with an existing material's response code to determine surface recession and char thickness. The calculation is performed for six 5-cm-diam models made of carbon-phenolic and carbon-carbon composite launched in the Track-G facility at the Arnold Engineering Development Center. Significant surface recessions are predicted to occur for these models due mostly to radiative heating.

Park, C.↗
NASA NTRS1985

Summary of recent NASA propeller research

Advanced high speed propellers offer large performance improvements for aircraft that cruise in the Mach 0.7 to 0.8 speed regime. At these speeds, studies indicate that there is a 15 to near 40 percent block fuel savings and associated operating cost benefits for advanced turboprops compared to equivalent technology turbofan powered aircraft. Recent wind tunnel results for five eight to ten blade advanced models are compared with analytical predictions. Test results show that blade sweep was important in achieving net efficiencies near 80 percent at Mach 0.8 and reducing nearfield cruise noise about 6 dB. Lifting line and lifting surface aerodynamic analysis codes are under development and some results are compared with propeller force and probe data. Also, analytical predictions are compared with some initial laser velocimeter measurements of the flow field velocities of an eight bladed 45 swept propeller. Experimental aeroelastic results indicate that cascade effects and blade sweep strongly affect propeller aeroelastic characteristics. Comparisons of propeller nearfield noise data with linear acoustic theory indicate that the theory adequately predicts nearfield noise for subsonic tip speeds, but overpredicts the noise for supersonic tip speeds.

Mikkelson, D. C.↗
NASA NTRS1989

High speed turboprop aeroacoustic study (single rotation). Volume 1: Model development

A frequency-domain noncompact-source theory for the steady loading and volume-displacement (thickness) noise of high speed propellers has been developed and programmed. Both near field and far field effects have been considered. The code utilizes blade surface pressure distributions obtained from three-dimensional nonlinear aerodynamic flow field analysis programs as input for evaluating the steady loading noise. Simplified mathematical models of the velocity fields induced at the propeller disk by nearby wing and fuselage surfaces and by angle-of-attack operation have been developed to provide estimates of the unsteady loading imposed on the propeller by these potential field type interactions. These unsteady blade loadings have been coupled to a chordwise compact propeller unsteady loading noise model to provide predictions of unsteady loading noise caused by these installation effects. Finally, an analysis to estimate the corrections to be applied to the free-field noise predictions in order to arrive at the measurable fuselage sound pressure levels has been formulated and programmed. This analysis considers the effects of fuselage surface reflection and diffraction together with surface boundary layer refraction. The steady loading and thickness model and the unsteady loading model have been verified using NASA-supplied data for the SR-2 and SR-3 model propfans. In addition, the steady loading and thickness model has been compared with data from the SR-6 model propfan. These theoretical models have been employed in the evaluation of the SR-7 powered Gulfstream aircraft in terms of noise characteristics at representative takeoff, cruise, and approach operating conditions. In all cases, agreement between theory and experiment is encouraging.

Whitfield, C. E.↗
NASA NTRS1991

An overview of the LeRC CSTI thermal management program

This report presents an integrated multielement project effort, currently being carried out at NASA LeRC, for the development of space heat rejection subsystems, with special emphasis on lightweight radiators, in support of SEI power system technology, and in particular the SP-100 program. Principal project elements include both contracted and in-house efforts. Included in the first category are two contracts aimed at the development of advanced radiator concepts, and demonstration of a flexible fabric heat pipe radiator concept. In-house work is designed to guide and support the overall program by system integration studies, heat pipe testing and analytical code development, radiator surface morphology alteration for emissivity enhancement, and composite materials research focused on the development of lightweight high conductivity fins.

Juhasz, Albert J.↗
NASA NTRS1991

An overview of the Lewis Research Center CSTI thermal management program

An integrated multi-element project effort, currently being carried out at NASA LeRC, for the development of space heat rejection subsystems, with special emphasis on lightweight radiators, in support of SEI power system technology, and in particular the SP-100 program, is reported. Principal project elements include both contracted and in-house efforts. Included in the first category are two contracts aimed at the development of advanced radiator concepts, and demonstration of a flexible fabric heat pipe radiator concept. In-house work is designed to guide and support the overall program by system integration studies, heat pipe testing and analytical code development, radiator surface morphology alteration for emissivity enhancement, and composite materials research focused on the development of lightweight high conductivity fins.

Juhasz, Albert J.↗
NASA NTRS1992

Viscous equilibrium computations using program LAURA

Modifications have been made to the Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) that enable it to compute viscous airflows under the assumption of thermal and chemical equilibrium. Equilibrium thermodynamic and transport property information are input to the code via curve fits. The periodic updating of this information enables the equilibrium algorithm to perform at a computational rate that is only a small percentage larger than the rate associated with the perfect-gas algorithm. Presented in this article are the results of the initial validation of the modified code. Solutions for surface pressure and heating are presented for the flow over slender and blunt cones at realistic reentry conditions. LAURA solutions are compared with those produced by a viscous shock-layer method, and, for one case considered, with heat transfer data from a flight experiment. For both pressure and heating, the agreement is good. In general, differences in pressure of a few percent were noted, while differences in heating rates were in the 5-10 percent range.

Greene, Francis A.↗