Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “structure performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Mechanical creep testing and characterization of Cr coated Zircaloy

Zirconium based cladding has been developed for use in light water reactor fuel applications due to the material’s desirable low neutron scattering cross section. To help improve corrosion resistance in accident conditions, such as a loss of coolant accident (LOCA), a chromium coating can be applied to the outer diameter of the Zircaloy tube. Cladding strength at reactor relevant temperatures is important for the structural performance. Stress relaxation creep testing was performed on Cr coated Zircaloy-4 to measure strain rate as a function of stress for 350 and 650°C. These were performed at both 5 ± 1 % and 7.5 ± 1 % strain. The lower temperature provides results near normal operating temperature, while the higher temperature provides results relevant to off-normal conditions where recrystallization will take place. Characterization was also performed to analyze the structure of the Cr coating and Zircaloy-4 as well as the interface between the two.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Effect of Fatigue on the Capacity and Performance of Structural Concrete

The goal of this project was to enhance the understanding of the fatigue behavior of concrete structures for the purpose of improving the design and assessment of towers and foundations that support wind turbines, which must endure repeated loadings from wind, waves, operations, and other dynamic effects that cause material degradation. This was achieved through physical experiments, a review of the technical literature, and collaboration with experts in key subject areas. The project produced a comprehensive database of publicly available fatigue data, several technical papers presenting the research findings, and two Technotes to be published by the American Concrete Institute that advance best practices in fatigue testing and enable the development of concrete-specific fatigue (S-N) (stress-life) curves. These contributions are expected to enhance the durability and cost-effectiveness of wind turbine support structures.

17 WIND ENERGY↗
DOE OSTI2024

Lattice Design and Advanced Modeling to Guide the Design of High-Performance Lightweight Structural Materials

Lightweight structural materials are required to increase the mobility of fission batteries. The materials must feature a robust combination of mechanical properties to demonstrate structural resilience. The primary objective of this project is to produce lightweight structural materials whose strength-to-weight ratios exceed those of the current widely used structural materials such as 316L stainless steels (316L SS). To achieve this, advanced modeling and simulation tools were employed to design lattice structures with different lattice parameters and different lattice types. A process was successfully developed for transforming lattice-structures models into Multiphysics Object Oriented Simulation Environment (MOOSE) inputs. Finite element modeling (FEM) was used to simulate the uniaxial tensile testing of the lattice-structured parts to investigate the stress distribution at a given displacement. The preliminary results showed that the lattice-structured sample displayed a lower Young’s modulus in comparison with the solid material and that the unit cell size of the lattice had a minimal effect. The novelty here is to apply up-front modeling to determine the best structure for the application before actually producing the sample. The approach of using modeling as a guiding tool for preliminary material design can significantly save time and cost for material development.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Aerothermal performance and structural integrity of a Rene 41 thermal protection system at Mach 6.6

A flightweight panel based on a metallic thermal-protection-system concept for hypersonic and reentry vehicles was subjected repeatedly to thermal cycling by quartz-lamp radiant heating using a thermal history representative of a reentry heat pulse and to aerodynamic heating at heating rates required to sustain a surface temperature of 1089 K (1960 R). The panel consisted of a corrugated heat shield and support members of 0.05-cm (0.02-in.) thick Rene 41 of riveted construction and 5.08-cm (2-in.) thick silica fibrous insulation packages covered by Rene 41 foil and inconel screening. All tests were conducted in the Langley 8-foot high-temperature structures tunnel with the heat shield corrugations alined in the stream direction. The panel sustained 5.33 hr of intermittent radiant heating and 6.5 min of intermittent aerodynamic heating of up to 1-min duration for differential pressures up to 6.2 kPa (0.9 psi) with no apparent degradation of thermal or structural integrity, as indicated by temperature distributions and results from load deflection tests and vibration surveys of natural frequencies.

Deveikis, W. D.↗
NASA NTRS1991

JPL control-structure interaction technology: Micro-precision CSI

The NASA Control-Structure Interaction (CSI) Program is described in outline and graphic form. Particular emphasis is given to the activities of the Jet Propulsion Lab. The goals of the program are (1) controlled structure performance enhancement, (2) controlled structure unified methods for design/analysis, and (3) ground validation methods for CSI flight systems.

Laskin, Robert A.↗
NASA NTRS1957

Cooling Performance and Structural Reliability of a Modified Corrugated-insert Air-cooled Turbine Blade with an Integrally Cast Shell and Base

A modified corrugated-insert blade with integrally cast shell and base was developed. This blade was as light as a conventional fabricated corrugated-insert blade. Of four test blades operated in a full-scale turbojet engine, one failed after about 15 hours operation at an inlet gas temperature of 1670 degrees F, a coolant-flow ratio of 0.0064, and a 1/3-span centrifugal stress of approximately 28,000 psi. Three other test blades ran for approximately 16, 31, and 36 hours without failure at similar conditions.

Freche, John C↗
NASA NTRS1995

Ceramic Replaces Metal In High Performance Optomechanical Structures

Recently developed ceramic materials and fabrication techniques integrated by Langley Research Center workers to produce superior optomechanical structures for spacecraft and aircraft instrumentation. Basic features of these novel supports, such as dimensional stability, low cost, and ease of fabrication, also make them ideal for many commerical optical systems as well. Ceramic supports for optical components and benches offer important advantages over usual metal parts. Ceramic materials expand and contract only slightly with changes in temperature. Moreover, they are relatively inexpensive and lightweight.

Vasquez, Peter↗
NASA NTRS2000

Modernization and Activation of the NASA Ames 11- by 11-Foot Transonic Wind Tunnel

The Unitary Plan Wind Tunnel (UPWT) was modernized to improve performance, capability, productivity, and reliability. Automation systems were installed in all three UPWT tunnel legs and the Auxiliaries facility. Major improvements were made to the four control rooms, model support systems, main drive motors, and main drive speed control. Pressure vessel repairs and refurbishment to the electrical distribution system were also completed. Significant changes were made to improve test section flow quality in the 11-by 11-Foot Transonic leg. After the completion of the construction phase of the project, acceptance and checkout testing was performed to demonstrate the capabilities of the modernized facility. A pneumatic test of the tunnel circuit was performed to verify the structural integrity of the pressure vessel before wind-on operations. Test section turbulence, flow angularity, and acoustic parameters were measured throughout the tunnel envelope to determine the effects of the tunnel flow quality improvements. The new control system processes were thoroughly checked during wind-off and wind-on operations. Manual subsystem modes and automated supervisory modes of tunnel operation were validated. The aerodynamic and structural performance of both the new composite compressor rotor blades and the old aluminum rotor blades was measured. The entire subsonic and supersonic envelope of the 11-by 11-Foot Transonic leg was defined up to the maximum total pressure.

Kmak, Frank J.↗
NASA NTRS2015

Preparation for Testing a Multi-Bay Box Subjected to Combined Loads

The COmbined Loads Test System (COLTS) facility at NASA Langley Research Center provides a test capability to help develop validated structures technologies. The test machine was design to accommodate a range of fuselage structures and wing sections and subject them to both quasistatic and cyclic loading conditions. The COLTS facility is capable of testing fuselage barrels up to 4.6 m in diameter and 13.7 m long with combined mechanical, internal pressure, and thermal loads. The COLTS facility is currently being prepared to conduct a combined mechanical and pressure loading for a multi-bay pressure box to experimentally verify the structural performance of a composite structure which is 9.1 meters long and representative of a section of a hybrid wing body fuselage section in support of the Environmentally Responsible Aviation Project at NASA. This paper describes development of the multi-bay pressure box test using the COLTS facility. The multi-bay test article will be subjected to mechanical loads and internal pressure loads up to design ultimate load. Mechanical and pressure loads will be applied independently in some tests and simultaneously in others.

Rouse, Marshall↗
DOE OSTI2021

“Flower-like” Li 4 Ti 5 O 12 -multiwalled carbon nanotube composite structures with performance as highrate anode-materials for li-ion battery applications and methods of synthesis thereof

A method of fabricating nanocomposite anode material embodying a lithium titanate (LTO)-multi-walled carbon nanotube (MWNT) composite intended for use in a lithium-ion battery includes providing multi-walled carbon nanotube (MWNTs), including nanotube surfaces, onto which functional oxygenated carboxylic acid moieties are arranged, generating 3D flower-like, lithium titanate (LTO) microspheres, including thin nanosheets and anchoring the acid-functionalized MWNTs onto surfaces of the 3D LTO microspheres by π-π interaction strategy to realize the nanocomposite anode material.

25 ENERGY STORAGE↗
DOE OSTI2022

Magnetite (Fe 3 O 4 )—multiwalled carbon nanotube composite structures with performance as high rate electrode materials for Li-ion batteries

A method of synthesizing an electrode material for lithium ion batteries from Fe 3 O 4 nanoparticles and multiwalled carbon nanotubes (MWNTs) to yield (Fe 3 O 4 -NWNTs) composite heterostructures. The method includes linking the Fe 3 O 4 nanoparticles and multiwalled carbon nanotubes using a π-π interaction synthesis process to yield the composite heterostructure electrode material. Since Fe 3 O 4 has an intermediate voltage, it can be considered an anode (when paired with a higher voltage material) or a cathode (when paired with a lower voltage material).

Wong, Stanislaus↗
DOE OSTI2022

Functional high-performance fiber structure

A method is provided for growing a fiber structure, where the method includes: obtaining a substrate, growing an array of pedestal fibers on the substrate, growing fibers on the pedestal fibers, and depositing a coating surrounding each of the fibers. In another aspect, a method of fabricating a fiber structure includes obtaining a substrate and growing a plurality of fibers on the substrate according to 1½D printing. In another aspect, a multilayer functional fiber is provided produced by, for instance, the above-noted methods.

Pegna, Joseph↗