Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strain hardening”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Anisotropic constitutive modeling for nickel base single crystal superalloy Rene N4 at 982 C

A back stress/drag stress constitutive model based on a crystallographic approach to model single crystal anisotropy is presented. Experimental results demonstrated the need for the back stress variable in the inelastic flow equations. Experimental findings suggested that back stress is orientation dependent and controls both strain hardening and recovery characteristics. Due to the observed stable fatigue loops at 1800 F, drag stress is considered constant for this temperature. The constitutive model operated with constraints determined only from tensile data was extensively tested from simple tensile and fatigue to complicated strain hold tests. The model predicted very well under those conditions.

Stouffer, D. C.↗
DOE OSTI2021

Determining failure properties of as-received and hydrided unirradiated Zircaloy-4 from ring compression tests

An integrated experimental and computational approach was developed to determine the plastic strain at fracture and to investigate the fracture energy of as-received and hydrided unirradiated Zircaloy-4 nuclear cladding tubes in the hoop direction at room temperature from ring compression testing (RCT). This work builds on previous methods in the literature that were developed to obtain the mechanical properties of nuclear cladding before fracture (Young’s modulus, yield stress, and strain-hardening parameters) from experimental RCT results and extends the characterization of this material class to include material failure properties. Furthermore, a ductile damage approach was developed and implemented in a validated finite element model to predict material failure, evaluate fracture energy, and quantify the plastic strain at fracture initiation. The hydrogen content of the Zircaloy-4 specimens was varied up to 610 wppm when the failure became brittle. As expected, increasing hydrogen content caused embrittlement of the Zircaloy-4 samples tested and the plastic strain at fracture and fracture energy to decrease.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural evolution in a precipitate-hardened (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 multi-principal element alloy during high-pressure torsion

Multi-principal element alloys demonstrate high strength, thermal stability, and irradiation resistance, making them excellent candidate materials for applications in nuclear reactors and other harsh environments. Some studies have examined the use of high-pressure torsion to strengthen MPEAs through grain size reduction and strain hardening. However, no studies have investigated the effect of HPT on secondary phases (precipitates) within an MPEA. Two alloys, (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 containing Ni(Ti, Al) B2 phase, and CrFe σ phase, and single-phase Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , were fabricated by casting and heat treatment. Both alloys were then processed with HPT to study microstructural evolution. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the alloys before and after HPT processing. HPT processing produced a nanocrystalline structure in both alloys, but (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 exhibited a significantly smaller grain size and higher dislocation density than Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , with corresponding higher hardness. Before HPT, the (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 alloy consisted of large grain (~ 400 μm) and precipitates, including B2 of ~ 38 μm average size, B2 of ~ 0.7 μm average size, and small amounts of σ of ~ 1.5 μm average size. After HPT, the larger B2 precipitates were decreased in size and volume fraction, while the smaller B2 precipitates were completely dissolved; the σ precipitates appeared unaffected by HPT, likely due to their much higher hardness. Finally, observation of the B2 precipitate distribution along radial distance indicates that the strain caused the precipitates to fracture at intermediate strain (γ = 125) and dissolve at high strain (γ = 280).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Material processing, microstructure, and composite properties of low carbon Engineered Cementitious Composites (ECC)

Traditional PVA fiber-reinforced Engineered Cementitious Composites (ECC) show high tensile ductility and superior durability with tight crack width, but the high cost and embodied carbon can hinder its wider application in infrastructures. The objective of this study is to develop a better understanding of the fresh and hardened properties of an ECC that employs a lower embodied-carbon binder, Limestone Calcined Clay Cement (LC3), and lower-cost PP fiber that is widely available. Specifically, the interrelations between material processing, microstructure, and composite properties were studied experimentally. The results showed that ECC with high tensile ductility up to 9% tensile strain and tight crack width with 50 μm at 2% tensile strain can be achieved. It was found that a matrix paste with higher viscosity generally enhanced fiber dispersion uniformity and robustness in tensile strain-hardening. The paste viscosity is increased when OPC is replaced by LC3 and can be tuned with superplasticizer content. Larger maximum flaw size leads to lower first crack strength, beneficial for microcrack initiation and multiple cracking. This study generates fundamental knowledge linking processing-microstructure-performance of PP-LC3-ECC. This class of low embodied carbon ECC with tight crack width is expected to contribute to reducing the carbon footprint of the built environment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultra-high temperature testing and performance of L-PBF C103

Additive Manufacturing (AM) of refractory alloys is gaining traction as a materials processing route for components subject to extreme temperature environments. Due to the low oxidation resistance of refractory alloys, novel methods for evaluating their elevated temperature performance must be developed. In this work, a Gleeble® 3800 thermomechanical load frame was modified to evaluate the mechanical properties of laser powder bed fusion (L-PBF) consolidated niobium alloy C103 ranging from room temperature (RT) to 1400 °C. The fixturing and sample geometry were designed to accommodate Joule heating and prevent damage to the test chamber. Oxidation of the samples was minimized via testing in vacuum level of 1E-5 Torr. Ultimate tensile strength (UTS), yield strength (YS), elongation, and strain-hardening behavior were determined as a function of temperature. L-PBF C103 presented an average UTS of ∼650 MPa and over 25 % elongation at RT. Above RT, the UTS and YS dropped then leveled off from 500 °C to 1000 °C with values ranging from ∼400 MPa to ∼460 MPa, which is consistent with dynamic strain aging observed in this class of alloys. The strength rapidly declined after 1200 °C to ∼150 MPa at 1400 °C. Fractography indicated ductile fractures for the C103 at all test temperatures, and Electron Backscatter Diffraction (EBSD) analysis revealed a textured microstructure and the presence of dynamic recrystallization within the necked region of the sample tested at 1400 °C.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

PVDF-based backsheet cracking: Mapping in situ phase evolution by X-ray scattering

One of the most common polymers used in commercial photovoltaic backsheets is polyvinylidene fluoride (PVDF). However, recent reports have shown the potential for PVDF-based backsheets to crack and fail prematurely. Previous work has suggested that polymer phase changes play a role in the failure mechanism. Here, in situ wide-angle X-ray scattering maps are used to show that α- to β-phase transformations occur at crack tips in aged PVDF-based backsheets under stretching. Substantial β-phase formation is shown to be associated with strain hardening. In addition, our work demonstrates that β-phase formation is not required for crack growth and only occurs at crack tips when plastic deformation of the PVDF polymer has occurred. In conclusion, the anisotropy in the strength of aged PVDF-based backsheets is linked to the lack of β-phase formation when strain is applied to aged backsheets in the transverse direction.

14 SOLAR ENERGY↗
NASA NTRSDate not supplied

Fracture Prediction of Epoxy Resin using Morse Bond Potential Embedded in GAFF using Molecular Dynamics Simulations

A generic method is developed to investigate the fracture behavior of an epoxy resin using atomistic molecular (MD) dynamics simulations. The epoxy system consisted of the stoichiometric mixture of tetra-/tri-functional epoxies and di-functional hardener molecules and was cured with a step-growth crosslinking algorithm. A hybrid force field (hFF) in which Morse bond function were added in second generation-general Amber Force Field (GAFF2) was used to capture bond breaking of the crosslinked epoxy system under uniaxial deformation. The Morse bond parameters for covalent bonds in the crosslinked backbone were fit to dissociation curves computed by CASPT2/6-311+G**. After the systems in various crosslink densities were obtained and equilibrated, the full length of stress-strain (𝜎-𝜀) curve was produced including initial elastic regime, yielding, plastic flow, strain hardening, and progressive failure. We found that the hFF was effective in studying the dissociation of crosslinked polymers and understanding the failure mechanism. In the results, the hFF delivered the same elastic property obtained from the unmodified force field GAFF. The stress-strain curve, however, began to be distinct in the plastic regime due to broken covalent bonds capable of altering the tensile behavior. Once the stress reached maximum, it progressively decreased until the ultimate failure (𝜎=0). Since hFF employed the existing GAFF functions with including a minimal change of its bond potential, this approach is easier to perform and computationally more efficient for unveiling the fracture behavior of polymer materials at the molecular level than other approaches with reactive force fields. We expect this approach will be utilized to accelerate the material-by-design process for thermosets by incorporate data from molecular models.

Changwoon Jang↗
DOE OSTI2025

Tailoring mechanical properties of a multi-principal element alloy through a multi-length-scale approach

In this study, a multi-length-scale strengthening approach was used to tailor the microstructure and the mechanical properties of a NiCoCr-based multi-principal element alloy (MPEA). Grain size refinement, severe lattice distortion, and stacking fault energy (SFE) reduction with Mo addition (up to 10 at.%) enhance yield strength by 85% with only 10% reduction in ductility in as-annealed MPEAs. A pronounced increase in the strain hardening rate was observed with the addition of Mo, which is ascribed to the promotion of complex stacking fault (SF) interaction and intersection, accompanied by Lomer-Cottrell (L-C) and Hirth locks inhibiting dislocation motion and substantial increase in the accumulation of back stress. To push the limit of the yield strength further, the Suzuki segregation phenomenon was manipulated by a careful control of SF density by pre-straining and a subsequent 500 °C heat treatment. The stress-strain responses of the pre-strained and heat treated MPEAs showed an obvious SF density and Mo concentration dependence. Furthermore, the yield strength of the pre-strained Mo-added MPEAs with subsequent heat treatment was increased up to true stress of 2.3 GPa with a corresponding fracture elongation of 12% true strain. SFs formed during pre-straining served as Cr segregation sites during subsequent heat treatment, which substantially varies the local SFE within the SF, presenting a roughened landscape and frustrating the dislocation dynamics.

mechanical properties↗
DOE OSTI2022

Dual-scale folding in cutting of commercially pure aluminum alloys

We examine a, hitherto, little-studied and curious machining chip morphology, with tell-tale signs of folding at two different length scales, that is common in cutting of certain ductile and highly strain-hardening metals like soft aluminum alloys, tantalum and niobium. This chip morphology does not appear in the usual catalogues of common chip types. The mechanics of formation of the “dual-scale folded chip” is studied in model material systems of commercially pure aluminum alloys (AA 1100 and AA 8040), that prominently exhibit this chip morphology. The flow, folding and associated plastic instabilities are investigated using micro/macro structure observations of the chip in a plane-strain cutting framework, with high-speed in situ imaging and image analysis of material flow; and force measurements. The smaller-scale folding is shown to develop in the primary deformation zone while the larger-scale folding occurs as the chip traverses the rake face of the tool. The resulting chip is composed of irregularly-spaced large folds, superimposed onto which are the quasi periodic small folds. The representative wavelengths of the two folds differ on average by an order of magnitude, 0.1 mm vs. 2 mm. The observations reveal a direct coupling between the material flow and chip morphology, and how specific attributes of the dual-scale folded chip arise from the flow mechanism. Plastic buckling is found to play a key role in the folding at both length scales. The small-scale folds are characteristic of a sinuous plastic flow mode, while the large-scale folding is characterized by buckling and stick-slip along the tool rake face, triggered by adhesive pinning of the chip to the tool. Important consequences of the dualscale folding are very large cutting forces, and force oscillations of large amplitude, despite the alloys being very soft, only ~ 25 HV. Here, the dual-scale folding is why many of these alloys are classified as “gummy” to machine. Since the dual-scale folded chip is associated with large cutting forces and poor surface quality, there is much to be gained by disrupting this flow type in practical machining applications. Methods for controlling the folding to improve machining performance with the gummy alloys are briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Irradiation hardening and ductility loss of Eurofer97 steel variants after neutron irradiation to ITER-TBM relevant conditions

Ten Eurofer97 steel variants, produced by non-standard fabrication-processing routes and modified alloying chemistries, were studied by neutron irradiations in the high flux isotope reactor. The irradiations were performed to ITER-TBM relevant conditions of ~255–350 °C, 2.94–3.24 dpa. We quantified the irradiation-induced degradation of the steels using mechanical property tests. All the steels suffered from irradiation hardening, where a significant increase in Vickers microhardness and yield stress (σ YS ) occurred, accompanied with severe loss of tensile elongation. The extent of hardening was material dependent. For T irr = 300±30 °C, most steels showed σ YS increase in the range of ~30% to as high as ~66%, except for a low temperature tempered steel with σYS increase below 15%. Despite large losses in elongation, most failures were ductile. Significant post-necking ductility was retained with reduction in area (RA) between 65–75%, but <50% for low temperature tempered steels. The ultimate tensile stress to yield stress (σ UTS /σ YS ) ratios decreased significantly after irradiation, highlighting irradiation-induced strain hardening capacity reduction. No major effect of irradiation on the plastic instability stress (σ PIS ) and true fracture stress of the steels was observed. By comparing the tensile stresses in true stress units and with literature, the results suggest that RAFM steel designing should target materials with a large separation between σ PIS and σ YS , to ensure the materials can maintain large work hardening and uniform deformation capability after irradiation. The tensile data of the steels additionally revealed a compelling evidence of an inverse trend between the change in RA and increase in σ YS of the neutron irradiated Eurofer97 type steels.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of phase-transformation path in TiZrHf(VNbTa)x refractory high-entropy alloys and its effect on mechanical property

Refractory high-entropy alloys (RHEAs) show a great potential as structural materials due to their remarkable properties, such as high strength and thermal stability. Despite these advantages, the RHEAs still suffer from the limited ductility at room temperature. To overcome the strength-ductility trade-off, the new RHEA design strategy, transformation-induced plasticity (TRIP) HEAs, have been developed by applying metastability-engineering approach. With the newly developed RHEAs design strategy, we designed metastable RHEAs, TiZrHfVxNbxTax (x = 1.0, 0.5 and 0.1) with decrease of the β-stabilizing elements (V, Nb, and Ta) to promote the transformation-induced ductility and work-hardening capability. The proper addition of the β-stabilizing elements (V, Nb, and Ta) into the ternary equi-molar TiZrHf alloy (TiZrHfV 0.1 Nb 0.1 Ta 0.1 ) leads to stress/strain-induced phase transformation from the body-centered cubic (BCC) to hexagonal-close-packed (HCP) α' and/or orthorhombic α" phases. Here, detailed studies on the phase transformation sequence during the deformation were carried out using X-ray diffraction (XRD), electron back-scattered diffraction (EBSD), and transmission-electron microscope (TEM), which revealed the stepwise phase transformation that is responsible for the strong strain hardening behavior. Furthermore, we further suggested the new transformation-induced-plasticity (TRIP) HEA design strategy, applying the Bo-Md approach.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Elastic interaction-induced anisotropic growth of dislocation loop arrays

The elastic interactions and reactions of dislocations lead to the formation of complex dislocation substructures, which is critical to the strain hardening and fatigue failure. Phase field dislocation dynamics simulations are conducted as a first step to understand the elastic interactions between dislocation loops. When the interloop spacing is small, the elastic interactions with neighboring loops become strong, rendering the edge segments strongly pinned, while allowing for the screw segments to propagate more easily. The interactions are found to result in an anisotropic stress distribution around the dislocation loops, leading to the formation of arrays of long, straight edge dislocations that could act as barriers to subsequent slip. Furthermore, the effect of initial loop size and applied strain rate on the elastic interaction-induced anisotropic pinning effect is investigated and discussed. Furthermore, the results are important for coarse-graining dislocation substructures formation into continuum level models of deformation in crystalline solids.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhanced mechanical properties of additive manufactured Grade 91 steel

High temperature stability of the mechanical properties, including creep behavior, are important factors to consider in certifying additive manufactured (AM) steels for reactor operation. AM-Grade 91 steel, tested at RT is shown to possess high yield strength, strain hardening and ductility even after high temperature aging for extended hours. Enhanced creep resistance at 650 ⁰C is also evident in the AM Grade 91 steel compared to wrought Grade 91 steel tested at the same conditions. In conclusion, the diverse and complex microstructure of this AM steel allows for both enhanced strength and ductility but increases the ductile-to-brittle transition temperature in these steels.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Study of Mechanical Properties, Microstructure, and Residual Stresses of AISI 304/304L Stainless Steel Submerged Arc Weld for Spent Fuel Dry Storage Systems

The confinement boundaries of spent nuclear fuel (SNF) canisters are typically fusion welded. Welded microstructures, strain hardening, and residual stresses combined with a chemically aggressive, chloride-rich environment led to concerns that the welded canister may be susceptible to chloride-induced stress corrosion cracking (CISCC). A comprehensive understanding of the modification of stainless steel (SS) metallurgical and mechanical properties by fusion welding could accelerate the predictive analysis of CISCC susceptibility. This paper describes a submerged arc welding (SAW) procedure that was developed and qualified on 12.7 mm (0.5 in.) thick AISI 304/304L SS to produce joints in a way similar to actual SNF canister manufacturing. This procedure has the potential to reduce the production cost and weld CISCC susceptibility by using fewer welding passes and lower heat input than current industrial applications. Global and local mechanical behaviors and properties, as well as residual stress distributions on the welded joint, were studied. The results indicate that hardness values in the fusion zone (FZ) and heat-affected zone (HAZ) are slightly higher than that of the base metal. Strain localization was presented in the HAZ before the tensile stress reached its maximum value, and then it shifted to the FZ. The specimen finally broke in the FZ. High tensile residual stresses exhibited in the FZ and the nearby HAZ suggest the highest CISCC-susceptible spots. The maximum tensile residual stresses were along the welding direction, indicating that if cracks occur, they would be perpendicular to the welding direction. This study involved developing and qualifying a SAW procedure for SNF canister production. The new procedure yielded cost savings (SAW working efficiency increased by about 80%), improved mechanical properties, and presented moderate residual stresses. Analysis revealed that the welded joint’s low-stress and high-stress damage assessments may be affected by shifts in the strain localization spot under loading.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1989

Deformation modeling and constitutive modeling for anisotropic superalloys

A study of deformation mechanisms in the single crystal superalloy PWA 1480 was conducted. Monotonic and cyclic tests were conducted from 20 to 1093 C. Both (001) and near-(123) crystals were tested, at strain rates of 0.5 and 50 percent/minute. The deformation behavior could be grouped into two temperature regimes: low temperatures, below 760 C; and high temperatures, above 820 to 950 C depending on the strain rate. At low temperatures, the mechanical behavior was very anisotropic. An orientation dependent CRSS, a tension-compression asymmetry, and anisotropic strain hardening were all observed. The material was deformed by planar octahedral slip. The anisotropic properties were correlated with the ease of cube cross-slip, as well as the number of active slip systems. At high temperatures, the material was isotropic, and deformed by homogeneous gamma by-pass. It was found that the temperature dependence of the formation of superlattice-intrinsic stacking faults was responsible for the local minimum in the CRSS of this alloy at 400 C. It was proposed that the cube cross-slip process must be reversible. This was used to explain the reversible tension-compression asymmetry, and was used to study models of cross-slip. As a result, the cross-slip model proposed by Paidar, Pope and Vitek was found to be consistent with the proposed slip reversibility. The results were related to anisotropic viscoplastic constitutive models. The model proposed by Walter and Jordan was found to be capable of modeling all aspects of the material anisotropy. Temperature and strain rate boundaries for the model were proposed, and guidelines for numerical experiments were proposed.

Milligan, Walter W.↗
DOE OSTI2024

Strong‐Yet‐Ductile Eutectic Alloys Employing Cocoon‐Like Nanometer‐Sized Dislocation Cells

Abstract Eutectic alloys (EAs) with superior fluidity are known to be the easiest to cast into high‐quality ingots, making them the alloys of choice for making large‐sized structural parts. However, conventional EAs (CEAs) have never reached strength–ductility combinations on par with the best in other alloy categories. Via thermomechanical processing of cast Ni‐32.88wt%Fe‐9.53wt%Al CEAs, a cocoon‐like nano‐meshed (as fine as 26 nm) network of dislocations (CNN‐D) is produced via recovery annealing, through the rearrangement of cold‐work‐accumulated dislocations anchored by dense pre‐existing nanoprecipitates. In lieu of traditional plasticity mechanisms, such as TWIP and TRIP, the CNN‐D is particularly effective in eutectic lamellae with alternating phases, as it instigates nanometer‐spaced planar slip bands that not only dynamically refine the microstructure but also transmit from the FCC (face‐centered‐cubic) layers into the otherwise brittle B2 layers. These additional mechanisms for strengthening and strain hardening sustain stable tensile flow, resulting in a striking elevation of both strength and ductility to outrank not only all previous CEAs, but also the state of the art—additively manufactured eutectic high‐entropy alloys. The CNN‐D thus adds a novel microstructural strategy for performance enhancement, especially for compositionally complex alloys that increasingly make use of nanoprecipitates or local chemical order.

Chemistry↗
DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)

A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Mechanical Behavior of High-Entropy Alloys: A Review

High-entropy alloys (HEAs) are materials that consist of equimolar or near-equimolar multiple principal components but tend to form single phases, which is a new research topic in the field of metallurgy, and have attracted extensive attention in the past decade. The HEAs families contain the face-centered-cubic (fcc), body-centered-cubic (bcc), and hexagonal-close-packed (hcp)-structured HEAs. On the one hand, mechanical properties, e.g., hardness, strength, ductility, fatigue, and elastic moduli, are essential for practical applications of HEAs. Scientists have explored in this direction since the advent of HEAs. On the other hand, the pursuit of high strength and good plasticity is the critical research issue of materials. Hence, strengthening of HEAs is a crucial issue.In this chapter, we reviewed the recent work on the room-temperature elastic properties and mechanical behavior of HEAs, including the mechanisms behind the plastic deformation of HEAs at both low and high temperatures. Furthermore, the present work examined the strengthening strategies of HEAs, e.g., strain hardening, grain-boundary strengthening, solid-solution strengthening, and particle strengthening. The fatigue, creep, and fracture properties were briefly introduced. Lastly, the future scientific issues and challenges of HEAs were discussed.

Shang, Yuanyuan↗