Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “storing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Stored energy function of rubberlike materials derived from simple tensile data.

An explicit formulation is developed to obtain the stored energy function, based on the Valanis-Landel separable symmetric stored energy function. This formulation is applicable to any multiaxial stress state, from simple tensile data alone, for those cases in which the stored energy function is a separable function of the stretch ratios. By direct comparison, it is also shown that styrene butadiene rubber, at least over a specific range, follows this postulated separable form.

Peng, T. J.↗
NASA NTRS1978

Effects of stores on longitudinal aerodynamic characteristics of a fighter at supersonic speeds

Experimental investigations of single and twin stores representative of advanced, elliptical cross section missile concepts were made at Mach numbers from 1.60 to 2.16 to substantiate theoretically predicted results. The stores were mounted on the fuselage of a model representing a fighter configuration. Store base closure effects in the carriage condition were also obtained through tests with and without base closure fairings.

Dollyhigh, S. M.↗
NASA NTRS1983

Effect of external stores on the stability and control characteristics of a delta wing fighter model at Mach numbers from 0.60 to 2.01

An investigation has been made to determine the effects of external stores on the stability and control characteristics of a delta wing fighter airplane model at Mach numbers from 0.60 to 2.01 for a Reynolds number of 3.0 X 1 million per foot. The angle-of-attack range was from about -4 degrees to 20 degrees at a sideslip angle of 0 degrees for the transonic tests, and from about -4 degrees to 10 degrees at sideslip angles of 0 degrees and 3 degrees for the supersonic tests. In general, the results of the tests indicated no seriously detrimental effects of the stores on the stability and control characteristics of the model but did show an increase in the minimum drag level throughout the Mach number range. However, the drag-due-to-lift was such that for subsonic/transonic speeds, the drag at higher lifts was essentially unaffected and the indications are that the maneuvering capability may not be impaired by the stores.

Spearman, M. L.↗
NASA NTRS1985

On applications of chimera grid schemes to store separation

A finite difference scheme which uses multiple overset meshes to simulate the aerodynamics of aircraft/store interaction and store separation is described. In this chimera, or multiple mesh, scheme, a complex configuration is mapped using a major grid about the main component of the configuration, and minor overset meshes are used to map each additional component such as a store. As a first step in modeling the aerodynamics of store separation, two dimensional inviscid flow calculations were carried out in which one of the minor meshes is allowed to move with respect to the major grid. Solutions of calibrated two dimensional problems indicate that allowing one mesh to move with respect to another does not adversely affect the time accuracy of an unsteady solution. Steady, inviscid three dimensional computations demonstrate the capability to simulate complex configurations, including closely packed multiple bodies.

Cougherty, F. C.↗
NASA NTRS1991

Impedances of Li/SO2 cells retrieved from the Long Duration Exposure Facility (LDEF satellite) and comparison with cells stored terrestrially

Impedances were measured on several Li/SO2 cells retrieved from the Long Duration Exposure Facility (LDEF) satellite. These cells were used to power instruments and recorders and had all been partially or fully discharged. Impedances were also measured on several cells that were stored in cold storage since manufacture. Unfortunately, none of the cells stored terrestrially had undergone any discharge, whereas all of the cells on the satellite were at least partially discharged early in the mission and then remained on orbit for about 5 years further. It has been observed by others that storage of an Li/SO2 cell after partial discharge, increases the resistance and thickness of the passive film on the Li electrode, as indicated by an increase in the time for recovery of voltage when a load is applied (voltage lag), or in some cases by an inability of a cell to sustain a normal current after such storage. Since the cells stored terrestrially were not discharged in the same manner as the LDEF cells, a direct comparison cannot be made. Thus, the effects of the space environment cannot be separated from the effects of storage after partial discharge. It is believed that the increases in impedance in the LDEF cells are largely due to the storage upon partial discharge rather than the effects of the space environment.

Reid, Margaret A.↗
NASA NTRS1993

Path planning by querying persistent stores of trajectory segments

We introduce an algorithm for path planning (long duration) paths of dynamical systems, given a persistent object store containing suitable collections of short duration trajectory segments. We also describe experimental results from a proof-of-concept implementation of the algorithm. The basic idea is to interpret a path planning algorithm as a suitable query on a persistent object store consisting of short duration trajectory segments. The query returns a concatenation of short duration trajectory segments which is close to the desired path. The needed short duration segments are computed by using a divide and conquer algorithm to break up the original path into shorter paths; each shorter path is then matched to a nearby trajectory segment which is part of the persistent object store by using a suitable index function.

Grossman, Robert L.↗
NASA NTRS1995

Alternate physical formats for storing data in HDF

Since its inception HDF has evolved to meet new demands by the scientific community to support new kinds of data and data structures, larger data sets, and larger numbers of data sets. The first generation of HDF supported simple objects and simple storage schemes. These objects were used to build more complex objects such as raster images and scientific data sets. The second generation of HDF provided alternate methods of storing data elements, making it possible to do such things as store extendible objects with in HDF, to store data externally from HDF files, and support data compression effectively. As we look to the next generation of HDF, we are considering fundamental changes to HDF, including a redefinition of the basic HDF object from a simple object to a more general, higher-level scientific data object that has certain characteristics, such as dimensionality, a more general atomic number type, and attributes. These changes suggest corresponding changes to the HDF file format itself.

Folk, Mike↗
NASA NTRS2003

Method for acquiring, storing and analyzing crystal images

A system utilizing a digital computer for acquiring, storing and evaluating crystal images. The system includes a video camera (12) which produces a digital output signal representative of a crystal specimen positioned within its focal window (16). The digitized output from the camera (12) is then stored on data storage media (32) together with other parameters inputted by a technician and relevant to the crystal specimen. Preferably, the digitized images are stored on removable media (32) while the parameters for different crystal specimens are maintained in a database (40) with indices to the digitized optical images on the other data storage media (32). Computer software is then utilized to identify not only the presence and number of crystals and the edges of the crystal specimens from the optical image, but to also rate the crystal specimens by various parameters, such as edge straightness, polygon formation, aspect ratio, surface clarity, crystal cracks and other defects or lack thereof, and other parameters relevant to the quality of the crystals.

Gester, Thomas E.↗
NASA NTRS2005

Modified Penning-Malmberg Trap for Storing Antiprotons

A modified Penning-Malmberg trap that could store a small cloud of antiprotons for a relatively long time (weeks) has been developed. This trap is intended for use in research on the feasibility of contemplated future matter/antimatter-annihilation systems as propulsion sources for spacecraft on long missions. This trap is also of interest in its own right as a means of storing and manipulating antiprotons for terrestrial scientific experimentation. The use of Penning-Malmberg traps to store antiprotons is not new. What is new here is the modified trap design, which utilizes state-of-the-art radiofrequency (RF) techniques, including ones that, heretofore, have been used in radio-communication applications but not in iontrap applications. A basic Penning-Malmberg trap includes an evacuated round tube that contains or is surrounded by three or more collinear tube electrodes. A steady axial magnetic field that reaches a maximum at the geometric center of the tube is applied by an external source, and DC bias voltages that give rise to an electrostatic potential that reaches a minimum at the center are applied to the electrodes. The combination of electric and magnetic fields confines the charged particles (ions or electrons) for which it was designed to a prolate spheroidal central region. However, geometric misalignments and the diffusive cooling process prevent the steady fields of a basic Penning- Malmberg trap from confining the particles indefinitely. In the modified Penning-Malmberg trap, the loss of antiprotons is reduced or eliminated by use of a "rotating-wall" RF stabilization scheme that also heats the antiproton cloud to minimize loss by matter/antimatter annihilation. The scheme involves the superposition of a quadrupole electric field that rotates about the cylindrical axis at a suitably chosen radio frequency. The modified Penning-Malmberg trap (see Figure 1) includes several collinear sets of electrodes inside a tubular vacuum chamber. Each set comprises either a single metal tube or else a tube that is segmented into four electrodes that subtend equal angles about the cylindrical axis. The output of an RF signal generator is fed through a 90 hybrid coupler and then through two baluns to generate four replicas of the signal at relative phase shifts of 0 , 90 , 180 , and 270 (see Figure 2). These signal replicas are fed through 6-dB directional couplers, then via coaxial cables to the vacuum chamber. The signal is then routed to a phase cancellation network, which filters out the drive signal with the difference representing the plasma interaction. Inside the vacuum chamber, twisted-pair wires feed the signals from the coaxial cables to the four electrodes of each segmented electrode tube.

Sims, William H.↗
NASA NTRS2014

Risk of Oxidative Damage to Bone from Increased Iron Stores During Space Flight

Iron stores are increased secondary to neocytolysis of red blood cells and a high dietary intake of iron during space flight. This raises concerns about the risk of excess iron causing oxidative damage in many tissues, including bone. Biomarkers of iron status, oxidative damage, and bone resorption during space flight were analyzed for 23 (16 M/7 F) International Space Station crewmembers as part of the Nutrition SMO project. Up to 5 in-flight blood samples and 24-h urine pools were collected over the course of the 4-6 month missions. Serum iron increased slightly during space flight and was decreased at landing (P < 0.0004). An increase in serum ferritin early in flight (217% in women and 68% in men, P < 0.0004), returning to preflight concentrations at landing, and a decrease in transferrin and transferrin receptors during flight indicated that a transient increase in iron stores occurred. No inflammatory response was observed during flight. The oxidative damage markers 8-hydroxy-2'-deoxyguanosine and prostaglandin F(sub 2(alpha)) were positively correlated (both P < 0.001) with serum ferritin. A greater area under the curve for ferritin during flight was correlated with greater changes in bone mineral density of several bone regions after flight (1). In a separate study (2), a ground-based investigation was conducted that examined the combined effects of radiation exposure and iron overload on sensitivity to radiation injury in several physiological systems in 12-wk male Sprague-Dawley rats. The rats were acclimated to an adequate iron diet (45 mg iron (ferric citrate)/kg diet) for 3 wk and then assigned to one of four groups: adequate iron (Fe) diet/no radiation, adequate Fe diet/ radiation, moderately high Fe diet (650 mg Fe (ferric citrate)/kg diet)/no radiation, and moderately high Fe diet/radiation. Animals remained on the assigned diet for 4 wk. Starting on day 14 of experimental diet treatment, animals were exposed to a fractionated dose (0.375 Gy) of Cs-137 every other day (3 Gy total dose). On day 29 (24 h after last radiation exposure), animals were euthanized. Oxidative stress markers in the liver, bone, eyes, and serum were assessed. There was evidence that the iron diet contributed to DNA damage as well as radiation exposure in the liver, eyes, and bone. Together, the results suggest that increased iron stores do constitute a risk factor for oxidative damage and bone resorption, during space flight and on Earth. Funded by the Human Health and Countermeasures Element of the NASA Human Research Program.

Zwart, S. R.↗
NASA NTRS2019

Analysis Ready Data in Analytics Optimized Data Stores for Analysis of Big Earth Data in the Cloud

Cloud computing offers the possibility of making the analysis of Big Data approachable for a wider community due to affordable access to computing power, an ecosystem of usable tools for parallel processing, and migration of many large datasets to archives in the cloud, allowing data-proximal computing. Generally, data analysis acceleration in the cloud comes from running multiple nodes in a split-combine-apply strategy. Data systems such as the Earth Observing System Data and Information System are in a position to "pre-split" the data by storing them in a data store that is optimized for data parallel computing, i.e., an Analytics-Optimized Data Store (AODS). A variety of approaches to AODS are possible, from highly scalable databases to scalable filesystems to data formats optimized for cloud access (e.g., zarr and cloud-optimized datasets), with the optimal choice dependent on both the types of analysis and the geospatial structure of the data. A key question is how much preprocessing of the data to do, both before splitting and as the first part of the apply step. Again, the geospatial structure of the data and the analysis type influence the decision, with the added complexity of the user type. Trans-disciplinary users who are not well-versed in the nuances of quality-filtering and georeferencing of remote sensing orbit/swath/scene data tend to ask for more highly processed data, relying on the data provider to make sensible decisions on preprocessing parameters. (This accounts for the popularity of "Level 3" gridded data, despite the lower spatial resolution it provides.) In this case, data can be preprocessed before the split, resulting in higher performance in the rest of the "apply" step, which can be transformative for use cases such as interactive data exploration at scale. Discipline researchers who are experienced with remote sensing data often prefer more flexibility in customizing the preprocessing data into Analysis Ready Data, resulting in more need for on-the-fly preprocessing.

Lynnes, Christopher↗
DOE OSTI2014

Control of Plasma-Stored Energy for Burn Control using DIII-D In-Vessel Coils

A new approach has been experimentally demonstrated to control the stored energy by applying a non-axisymmetric magnetic field using the DIII-D in-vessel coils to modify the energy confinement time. In future burning plasma experiments as well as magnetic fusion energy power plants, various concepts have been proposed to control the fusion power. The fusion power in a power plant operating at high gain can be related to the plasma-stored energy and hence, is a strong function of the energy confinement time. Thus, an actuator, that modifies the confinement time, can be used to adjust the fusion power. In relatively low collisionality DIII-D discharges, the application of non-axisymmetric magnetic fields results in a decrease in confinement time and density pumpout. Gas puffing was used to compensate the density pumpout in the pedestal while control of the stored energy was demonstrated by the application of non-axisymmetric fields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

Signature-based store checking buffer

A system and method for optimizing redundant output verification, are provided. A hardware-based store fingerprint buffer receives multiple instances of output from multiple instances of computation. The store fingerprint buffer generates a signature from the content included in the multiple instances of output. When a barrier is reached, the store fingerprint buffer uses the signature to verify the content is error-free.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2016

Systems and methods of storing combustion waste products

In one aspect, methods of storing one or more combustion waste products are described herein. Combustion waste products stored by a method described herein can include solid combustion waste products such as coal ash and/or gaseous combustion products such as carbon dioxide. In some embodiments, a method of storing carbon dioxide comprises providing a carbon dioxide storage medium comprising porous concrete having a macroporous and microporous pore structure and flowing carbon dioxide captured from a combustion flue gas source into the pore structure of the porous concrete.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2016

Parallel sort with a ranged, partitioned key-value store in a high perfomance computing environment

Improved sorting techniques are provided that perform a parallel sort using a ranged, partitioned key-value store in a high performance computing (HPC) environment. A plurality of input data files comprising unsorted key-value data in a partitioned key-value store are sorted. The partitioned key-value store comprises a range server for each of a plurality of ranges. Each input data file has an associated reader thread. Each reader thread reads the unsorted key-value data in the corresponding input data file and performs a local sort of the unsorted key-value data to generate sorted key-value data. A plurality of sorted, ranged subsets of each of the sorted key-value data are generated based on the plurality of ranges. Each sorted, ranged subset corresponds to a given one of the ranges and is provided to one of the range servers corresponding to the range of the sorted, ranged subset. Each range server sorts the received sorted, ranged subsets and provides a sorted range. A plurality of the sorted ranges are concatenated to obtain a globally sorted result.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2015

Systems, methods, and devices for tagging carbon dioxide stored in geological formations

The invention provides methods and systems for tagging carbon dioxide to be stored in a geologic formation. In some embodiments, a method includes: providing a carbon dioxide tracer that is quantifiable and distinguishable versus non-anthropogenic produced carbon dioxide; providing carbon dioxide to be stored in the geologic formation; determining what portion of the carbon dioxide is anthropogenic produced carbon dioxide; and mixing a predetermined quantity of the carbon dioxide tracer with the carbon dioxide stored to develop a tagged quantity of carbon dioxide for storage in the geologic formation. In some embodiments, a system for tagging a stream of carbon dioxide includes a tagging module and a mixing module. Tagging module includes a carbon dioxide tracer that is quantifiable and distinguishable versus non-anthropogenic produced carbon dioxide. Mixing module includes mechanisms for containing and injecting the carbon dioxide tracer into a stream of carbon dioxide.

Lackner, Klaus S.↗
DOE OSTI2019

Error detection and correction utilizing locally stored parity information

A processing system includes a memory coupled to a processor. The memory stores data blocks, with each data block having a separate associated checksum value stored along with the data block in the memory. The processor has a storage location that stores parity information for the data blocks, with the parity information having a plurality of parity blocks. Each parity block represents a parity of a corresponding set of data blocks. The parity blocks can be accessed for use in error detection and correction schemes used by the processing system.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2013

License Amendment Request for Storing Exelon Sister Nuclear Stations Class B/C LLRW in the LaSalle Station Interim Radwaste Storage Facility - 13620

Exelon Nuclear (Exelon) designed and constructed an Interim Radwaste Storage Facility (IRSF) in the mid-1980's at LaSalle County Nuclear Station (LaSalle). The facility was designed to store low-level radioactive waste (LLRW) on an interim basis, i.e., up to five years. The primary reason for the IRSF was to offset lack of disposal in case existing disposal facilities, such as the Southeast Compact's Barnwell Disposal Facility in Barnwell, South Carolina, ceased accepting radioactive waste from utilities not in the Southeast Compact. Approximately ninety percent of the Radwaste projected to be stored in the LaSalle IRSF in that period of time was Class A, with the balance being Class B/C waste. On July 1, 2008 the Barnwell Disposal Facility in the Southeast Compact closed its doors to out of- compact Radwaste, which precluded LaSalle from shipping Class B/C Radwaste to an outside disposal facility. Class A waste generated by LaSalle is still able to be disposed at the 'Envirocare of Utah LLRW Disposal Complex' in Clive, Utah. Thus the need for utilizing the LaSalle IRSF for storing Class B/C Radwaste for an extended period, perhaps life-of-plant or more became apparent. Additionally, other Exelon Midwest nuclear stations located in Illinois that did not build an IRSF heretofore also needed extended Radwaste storage. In early 2009, Exelon made a decision to forward Radwaste from the Byron Nuclear Station (Byron), Braidwood Nuclear Station (Braidwood), and Clinton Nuclear Station (Clinton) to LaSalle's IRSF. As only Class B/C Radwaste would need to be forwarded to LaSalle, the original volumetric capacity of the LaSalle IRSF was capable of handling the small number of additional expected shipments annually from the Exelon sister nuclear stations in Illinois. Forwarding Class B/C Radwaste from the Exelon sister nuclear stations in Illinois to LaSalle would require an amendment to the LaSalle Station operating license. Exelon submitted the License Amendment Request (LAR) to NRC on January 6, 2010; NRC approved the LAR on July 21, 2011. A similar decision was made by Exelon in early 2009 to forward Radwaste from Limerick Nuclear Station to its sister station, the Peach Bottom Atomic Power Station; both in Pennsylvania. A LAR submittal to the NRC was also provided and NRC approval was received in 2011. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗