Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stoichiometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Thermoelectric properties of non-stoichiometric lanthanum sulfides

The lanthanum sulfides are promising candidate materials for high-efficiency thermoelectric applications at temperatures up to 1300 C. The non-stoichiometric lanthanum sulfides (LaS(x), where x is in the range 1.33-1.50) appear to possess the most favorable thermoelectric properties. The Seebeck coefficient and resistivity vary significantly with composition, so that an optimum value of alpha sq/rho (where alpha is the Seebeck coefficient and rho is the resistivity) can be chosen. The thermal conductivity remains approximately constant with stoichiometry, so a material with an optimum value of alpha sq/rho should possess the optimum figure-of-merit. Data for the Seebeck coefficient and electrical resistivity of non-stoichiometric lanthanum sulfides will be pressed, together with structural properties of these materials.

Shapiro, E.↗

Fermi energy control of vacancy coalescence and dislocation density in melt-grown GaAs

A striking effect of the Fermi energy on the dislocation density in melt-grown GaAs has been discovered. Thus, a shift of the Fermi energy from 0.1 eV above to 0.2 eV below its intrinsic value (at high temperature, i.e., near 1100 K) increases the dislocation density by as much as five orders of magnitude. The Fermi energy shift was brought about by n-type and p-type doping at a level of about 10 to the 17th per cu cm (under conditions of optimum partial pressure of As, i.e., under optimum melt stoichiometry). This effect must be associated with the fact that the Fermi energy controls the charge state of vacancies (i.e., the occupancy of the associated electronic states) which in turn must control their tendency to coalesce and thus the dislocation density. It appears most likely that gallium vacancies are the critical species.

Lagowski, J.↗

Global carbon - nitrogen - phosphorus cycle interactions: A key to solving the atmospheric CO2 balance problem?

If all biotic sinks of atmospheric CO2 reported were added a value of about 0.4 Gt C/yr would be found. For each category, a very high (non-conservative) estimate was used. This still does not provide a sufficient basis for achieving a balance between the sources and sinks of atmospheric CO2. The bulk of the discrepancy lies in a combination of errors in the major terms, the greatest being in a combination of errors in the major terms, the greatest being in the net biotic release and ocean uptake segments, but smaller errors or biases may exist in calculations of the rate of atmospheric CO2 increase and total fossil fuel use as well. The reason why biotic sinks are not capable of balancing the CO2 increase via nutrient-matching in the short-term is apparent from a comparison of the stoichiometry of the sources and sinks. The burning of fossil fuels and forest biomass releases much more CO2-carbon than is sequestered as organic carbon.

Peterson, B. J.↗

Alloys based on NiAl for high temperature applications

The NiAl alloys for potential high temperature applications were studied. Alloys were prepared by powder metallurgy techniques. Flow stress values at slow strain rates and high temperatures were measured. Some ternary alloying additions (Hf, Ta and Nb) were identified. The mechanism of strengthening in alloys containing these additions appears to be a form of particle dislocation interaction. The effects of grain size and stoichiometry in binary alloys are also presented.

Vedula, K. M.↗

Biological modulation of planetary atmospheres: The early Earth scenario

The establishment and subsequent evolution of life on Earth had a profound impact on the chemical regime at the planet's surface and its atmosphere. A thermodynamic gradient was imposed on near-surface environments that served as the driving force for a number on important geochemical transformations. An example is the redox imbalance between the modern atmosphere and the material of the Earth's crust. Current photochemical models predict extremely low partial pressures of oxygen in the Earth's prebiological atmosphere. There is widespread consensus that any large-scale oxygenation of the primitive atmosphere was contingent on the advent of biological (autotrophic) carbon fixation. It is suggested that photoautotrophy existed both as a biochemical process and as a geochemical agent since at least 3.8 Ga ago. Combining the stoichiometry of the photosynthesis reaction with a carbon isotope mass balance and current concepts for the evolution of the stationary sedimentary mass as a funion of time, it is possible to quantify, the accumulation of oxygen and its photosynthetic oxidation equivalents through Earth history.

Schidlowski, M.↗

Size and shape dependence of CO adsorption sites on sapphire supported Fe microcrystals

The surface structure and stoichiometry of alumina substrates, as well as the size, growth characteristics, and shape of Fe deposits on sapphire substrates have been investigated by low energy electron diffraction (LEED), Auger electron spectroscopy, electron energy loss spectroscopy, and X-ray photoemission spectroscopy (XPS), as well as work function measurements, in conjunction with transition electron microscopy observations. The substrates used in this work were the following: (1) new, clean Al2O3; (2) same surface amorphized by Ar ion bombardment; (3) same surface regenerated by 650 C annealing; (4) amorphous alumina films on Ta slab; and (5) polycrystal alumina films, obtained by heating amorphous films to 600 C. Substrate cleaning was found to be most effective in producing a reproducible surface upon oxygen RF plasma treatment. The Fe nucleation and growth process was found to depend strongly on the type of substrate surface and deposition conditions. Ar ion bombardment under beam flooding, and subsequent annealing at 650 C was found an effective means to restore the original Al2O3 (1102) surface for renewed Fe deposition.

Papageorgopoulos, C.↗

Spectral and other physicochemical properties of submicron powders of hematite (alpha-Fe2O3), maghemite (gamma-Fe2O3), magnetite (Fe3O4), goethite (alpha-FeOOH), and lepidocrocite (gamma-FeOOH)

The spectral properties (0.35-2.20 microns) of submicron powders of hematite, maghemite, magnetite, goethite, and lepidocrocite are determined. Other physicochemical data are obtained for the powders in order to determine if deviations from stoichiometry occur due to their small particle size, to determine their state of chemical and phase purity, and to determine the physical characteristics of the individual powders. The physicochemical data obtained include mean particle diameter, discrete particle shape, chemical composition, crystallographic phase, magnetic parameters, and Moessbauer parameters. The positions of the spectral features for the hematite, maghemite, and magnetite powders are independent of temperature over the interval between about +20 and -110 C. For the goethite and lepidocrocite powders, a small shift of about 0.02 micron to shorter wavelengths is observed for some of the features after cooling to about -110 C. The spectral properties of the iron oxides and oxyhydroxides are important not only for understanding the basic physics and chemistry of the compounds but also for applications such as the remote sensing of the earth and Mars.

Morris, R. V.↗

EL2 and related defects in GaAs - Challenges and pitfalls

The incorporation process of nonequilibrium vacancies in melt-grown GaAs is strongly complicated by deviations from stoichiometry and the presence of two sublattices. Many of the microdefects originating in these vacancies and their interactions introduce energy levels (shallow and deep) within the energy gap. The direct identification of the chemical or structural signature of these defects and its direct correlation to their electronic behavior is not generally possible. It is necessary, therefore, to rely on indirect methods and phenomenological models and deal with the associated pitfalls. EL2, a microdefect introducing a deep donor level, has been in the limelight in recent years because it is believed to be responsible for the semi-insulating behavior of undoped GaAs. Although much progress has been made towards understanding its origin and nature, some relevant questions remain unanswered. An attempt is made to assess the present status of understanding of EL2 in the light of most recent results.

Gatos, H. C.↗

Oxides of Nitrogen Emissions from the Combustion of Monodisperse Liquid Fuel Sprays

A study of NO sub x formation in a one dimensional monodisperse spray combustion system, which allowed independent droplet size variation, was conducted. Temperature, NO and NO sub x concentrations were measured in the transition region, encompassing a 26 to 74 micron droplet size range. Emission measurements of hydrocarbons, carbon monoxide, carbon dioxide and oxygen were also made. The equivalence ratio was varied between 0.8 and 1.2 for the fuels used, including methanol, isopropanaol, n-heptane and n-octane. Pyridine and pyrrole were added to n-heptane as nitrogen-containing additives in order to simulate synthetic fuels. Results obtained from the postflame regions using the pure fuels indicate an optimum droplet size in the range of 43 to 58 microns for minimizing NO sub x production. For the fuels examined, the maximum NO sub x reductions relative to the small droplet size limit were about 10 to 20% for lean and 20 to 30% for stoichiometric and rich mixtures. This behavior is attributed to droplet interactions and the transition from diffusive to premixed type of burning. Preflame vaporization controls the gas phase stoichiometry which has a significant effect on the volume of the hot gases surrounding a fuel droplet, where NO sub x is formed.

Sarv, H.↗

Graphite fiber intercalation: Basic properties of copper chloride intercalated fibers

In situ resistance measurements were used to follow the intercalation of copper chloride in pitch-based fibers. Subsequent single fiber resistivity measurements reveal a large range of resistivities, from 13 to 160 micro-ohms cm. Additional density measurements reveal a bimodal distribution of mass densities. The dense fibers have lower resistivities and correspond to the stage III compound identified by X-ray diffraction. Neither resistivity nor density correlate with diameter. Both energy dispersive spectroscopy and mass density data suggest that excess chlorine resides in the intercalated fiber, resulting in a stoichiometry of C4.9n CuCl2.5 (where n is the stage number) for the denser fibers. Finally, thermogravimetric analysis shows a 33 percent loss in mass upon heating to 700C. This loss in mass is attributed to loss of both chlorine and carbon.

Jaworske, D. A.↗

Photoenergy transduction in halobacterium halobium

The structure and function of a rhodopsin-like pigment bacteriorhodopsin, discovered and isolated from the membranes of the halophile Halobacterium halobium, were studied. Intermediatesm appearing in the cyclic photoreaction that drives the proton translocation, were spectroscopically characterized. The charge translocation in membrane monolayers and mulitlayers placed between electrodes were kinetically resolved. A model was developed for the proton translocation process, in which the isomerization of the retinal Schiff base decreases its pK to drive the proton off and simultaneaouly changes the connectivity from the cytoplasmic surface to the external surface. The stoichiometry of proton pumping in intact cells and the effect of the light generated electrochemical potential on the kinetics of the photoreaction cycle and the synthesis of ATP were investigated.

Stoeckenius, W.↗

Crystal growth of device quality GaAs in space

It was established that the findings on elemental semiconductors Ge and Si regarding crystal growth, segregation, chemical composition, defect interactions, and materials properties-electronic properties relationships are not necessarily applicable to GaAs (and to other semiconductor compounds). In many instances totally unexpected relationships were found to prevail. It was further established that in compound semiconductors with a volatile constituent, control of stoichiometry is far more critical than any other crystal growth parameter. It was also shown that, due to suppression of nonstoichiometric fluctuations, the advantages of space for growth of semiconductor compounds extend far beyond those observed in elemental semiconductors. A novel configuration was discovered for partial confinement of GaAs melt in space which overcomes the two major problems associated with growth of semiconductors in total confinement. They are volume expansion during solidification and control of pressure of the volatile constituent. These problems are discussed in detail.

Gatos, H. C.↗

Production rates of neon xenon isotopes by energetic neutrons

As a first step in an experimental program to study the behavior of noble gases produced in situ in minerals, a suite of minerals and pure chemicals were irradiated with 14.5 MeV neutrons at LLNL's Rotating Target Neutron Source (RTNS-II) and production rates for noble gases were determined. While neutron effects in meteorites and lunar samples are dominated by low-energy neutron capture, more energetic cosmic-ray secondary neutrons can provide significant depth-dependent contributions to production of cosmogenic nuclides through endothermic reactions such as (n,2n), (n,np), (n,d) and (n,alpha). Production rates for nuclides produced by cosmic-ray secondary neutrons are therefore useful in interpreting shielding histories from the relative abundances of cosmogenic nuclides. Absolute production cross sections were calculated from isotope dilution analyses of NaCl, Mg, CsCl, and Ba(NO3)2 samples, assuming purity, stoichiometry, and quantitative noble gas retention and extraction. Relative production cross sections determined from neon isotopic ratios in the mineral samples were also considered in evaluating the neon production cross sections. Results are presented.

Leich, D. A.↗

Partially confined configuration for the growth of semiconductor crystals from the melt in zero-gravity environment

A novel partially confined configuration is proposed for the crystal growth of semiconductors from the melt, including those with volatile constituents. A triangular prism is employed to contain the growth melt. Due to surface tension, the melt will acquire a cylindrical-like shape and thus contact the prism along three parallel lines. The three empty spaces between the cylindrical melt and the edges of the prism will accommodate the expansion of the solidifying semiconductor, and in the case of semiconductor compounds with a volatile constituent, will permit the presence of the desired vapor phase in contact with the melt for controlling the melt stoichiometry. Theoretical and experimental evidence in support of this new type of confinement is presented.

Lagowski, J.↗

EL2 and related defects in GaAs - Challenges and pitfalls

The incorporation process of nonequilibrium vacancies in melt-grown GaAs is strongly complicated by deviations from stoichiometry, and the presence of two sublattices. Many of the microdefects originating in these vacancies and their interactions introduce energy levels (shallow and deep) within the energy gap. The direct identification of the chemical or structural signature of these defects and its direct correlation to their electronic behavior is not generally possible. It is therefore necessary to rely on indirect methods and phenomenological models and be confronted with the associated pitfalls. EL2, a microdefect introducing a deep donor level, has been in the limelight in recent years because it is believed to be responsible for the semi-insulating behavior of undoped GaAs. Although much progress has been made towards understanding its origin and nature, some relevant questions remain unanswered. An attempt is made to assess the present status of understanding of EL2 in the light of the most recent results.

Gatos, H. C.↗

An experimental investigation on flame interaction and the existence of negative flame speeds

Downstream interaction between two counterflow premixed flames of different stoichiometries are investigated. Various flame configurations are observed and quantified; these include the binary system of two lean or rich flames, the triplet system of a lean and a rich flame separated by a diffusion flame, and single diffusion flames with some degree of premixedness. Extinction limits are determined for methane/air and butane/air mixtures over the entire range of mixture concentrations. Results show that these extinction limits can be significantly modified in the presence of interaction such that a mixture much beyond the flammability limit can still burn if it is supported by a stronger flame. The experiment also demonstrates the existence of negative flames whose propagation velocity is in the same general direction as that of the bulk convective flow. Implications of the present results on the flammability of stratified mixtures and on the modeling of turbulent flames are discussed.

Sohrab, S. H.↗

New methods for image collection and analysis in scanning Auger microscopy

While scanning Auger micrographs are used extensively for illustrating the stoichiometry of complex surfaces and for indicating areas of interest for fine point Auger spectroscopy, there are many problems in the quantification and analysis of Auger images. These problems include multiple contrast mechanisms and the lack of meaningful relationships with other Auger data. Collection of multielemental Auger images allows some new approaches to image analysis and presentation. Information about the distribution and quantity of elemental combinations at a surface are retrievable, and particular combinations of elements can be imaged, such as alloy phases. Results from the precipitate hardened alloy Al-2124 illustrate multispectral Auger imaging.

Browning, R.↗

Analysis of the effects of fuel spray characteristics on NO(x) formation

Results from experimental and analytical studies on NO(x) formation in a one-dimensional monodisperse spray combustion system are reported. In a previous investigation, an optimum droplet diameter was reported for minimizing NO(x) emissions. In this paper, the effects of enhanced prevaporization and droplet interactions in addition to droplet size effects on NO(x) formation are investigated by air preheating experiments. These phenomena have been incorporated into an analytical model which predicts NO(x) formed from the combustion of monodisperse fuel sprays. Both, experimental and computed results indicate the importance of the extent of prevaporization and droplet interactions on NO(x) production. Preflame vaporization controls the gas phase stoichiometry which has a significant effect on the volume of the hot gases surrounding a fuel droplet where NO(x) is formed. On the other hand, the release of fuel vapor from the droplet to the reaction zone is influenced by droplet interactions which reduce the volume of the hot gases and NO(x) production by bringing the flame closer to the droplet surface.

Sarv, H.↗