Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “source location”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

An iterative method for obtaining the optimum lightning location on a spherical surface

A brief introduction to the basic principles of an eigen method used to obtain the optimum source location of lightning is presented. The location of the optimum source is obtained by using multiple direction finders (DF's) on a spherical surface. An improvement of this method, which takes the distance of source-DF's as a constant, is presented. It is pointed out that using a weight factor of signal strength is not the most ideal method because of the inexact inverse signal strength-distance relation and the inaccurate signal amplitude. An iterative calculation method is presented using the distance from the source to the DF as a weight factor. This improved method has higher accuracy and needs only a little more calculation time. Some computer simulations for a 4DF system are presented to show the improvement of location through use of the iterative method.

Chao, Gao↗

Scattering of terrestrial kilometric radiation at very high altitudes

On a number of occasions during the 3.8 yr. operating lifetime of RAE-2, strong terrestrial kilometric radiation was observed when the spacecraft was over the far side of the moon and when the low altitude terrestrial magnetosphere was completely obscured from view. If these deep lunar occultation events are used to infer radio source locations, then it is found that the apparent source must sometimes be situated at geocentric distances of 10 to 40 sub E or more. From an analysis of these events, it is shown that they are probably due to propagation effects rather than the actual generation of the emission at such large distances. The kilometric radiation can be generated near the earth at auroral latitudes and subsequently strongly scattered in the magnetosheath and nearby solar wind to produce the large apparent distances. The most likely scatterers are density inhomogeneities in the magnetosheath plasma and ion plasma waves in the magnetosheath and the upstream solar wind.

Alexander, J. K.↗

Scattering of terrestrial kilometric radiation at very high altitudes

On a number of occasions during the 3.5-yr operating lifetime of Rae 2, strong terrestrial kilometric radiation has been observed when the spacecraft was over the far side of the moon and when the low-altitude terrestrial magnetosphere was completely obscured from view. If these deep lunar occultation events are used to infer radio source locations, then it is found that the apparent source must sometimes be situated at geocentric distances of 10-40 earth-radii or more. From an analysis of these events, it is shown that they are probably due to propagation effects rather than the actual generation of the emission at such large distances. The kilometric radiation can be generated near the earth at auroral latitudes and subsequently strongly scattered in the magnetosheath and nearby solar wind to produce the large apparent distances. The most likely scatterers are density inhomogeneities in the magnetosheath plasma and ion plasma waves in the magnetosheath and the upstream solar wind.

Alexander, J. K.↗

A model for intensity profiles of dust jets near the nucleus of Comet Halley

The Giotto spacecraft's Halley Multicolor Camera images have been used to derive intensity profiles of the jetlike dust features that are associated with active regions of the Comet Halley nucleus. An intensity profile's asymptotic behavior at a radius greater than 100 km from the nucleus can be seen as arising from a source located at a hypothetical point below the active source region. Several source distributions are investigated. The extended source model considers divergent dust flow from an active area of arbitrary shape. It is concluded that the surface is neither smooth nor homogeneous, but must instead be characterized by varying curvature and roughness in order to reflect the observed conical dust flow.

Huebner, W. F.↗

Reflection type skin friction meter

A housing block is provided having an upper surface conforming to the test surface of a model or aircraft. An oil film is supplied upstream of a transparent wedge window located in this upper surface by an oil pump system located external to the housing block. A light source located within the housing block supplies a light beam which passes through this transparent window and is reflected back through the transparent window by the upper surface of the oil film to a photo-sensitive position sensor located within the housing. This position sensor allows the slope history of the oil film caused by and aerodynamic flow to be determined. The skin friction is determined from this slope history. Internally located mirrors augment and sensitize the reflected beam as necessary before reaching the position sensor. In addition, a filter may be provided before this sensor to filter the beam.

Bandyopadhyay, Promode R.↗

Possible Very Distant or Optically Dark Cluster of Galaxies

The goal of this proposal was an XMM followup observation of the extended X-ray source detected in our ROSAT PSPC cluster survey. Approximately 95% of extended X-ray sources found in the ROSAT data were optically identified as clusters of galaxies. However, we failed to find any optical counterparts for C10952-0148. Two possibilities remained prior to the XMM observation: (1) This is was a very distant or optically dark cluster of galaxies, too faint in the optical, in which case XMM would easily detect extended X-ray emission and (2) this was a group of point-like sources, blurred to a single extended source in the ROSAT data, but easily resolvable by XMM due to a better energy resolution. The XMM data have settled the case --- C10952-0148 is a group of 7 relatively bright point sources located within 1 square arcmin. All but one source have no optical counterparts down to I=22. Potentially, this can be an interesting group of quasars at a high redshift. We are planning further optical and infrared followup of this system.

Vikhlinin, Alexey↗

The x ray reflectivity of the AXAF VETA-I optics

The x-ray reflectivity of the VETA-I optic, the outermost shell of the AXAF x-ray telescope, with a bare Zerodur surface, is measured and compared with theoretical predictions. Measurements made at energies of 0.28, 0.9, 1.5, 2.1, and 2.3 keV are compared with predictions based on ray trace calculations. The data were obtained at the x-ray calibrations facility at Marshall Space Flight Center with an electron impact x-ray source located 528 m from the grazing incidence mirror. The source used photoelectric absorption filters to eliminate bremsstrahlung continuum. The mirror has a diameter of 1.2 m and a focal length of 10 m. The incident and reflected x-ray flux are detected using two proportional counters, one located in the incident beam of x-rays at the entrance aperture of the VETA-I, and the other in the focal plane behind an aperture of variable size. Results on the variation of the reflectivity with energy as well as the absolute value of the reflectivity are presented. We also present a synchrotron reflectivity measurement with high energy resolution over the range 0.26 to 1.8 keV on a flat Zerodur sample, done at NSLS. We present evidence for contamination of the flat by a thin layer of carbon on the surface, and the possibility of alteration of the surface composition of the VETA-I mirror perhaps by the polishing technique. The overall agreement between the measured and calculated effective area of VETA-I is between 2.6 percent and 10 percent, depending on which model for the surface composition is adopted. Measurements at individual energies deviate from the best-fitting calculation to 0.3 to 0.8 percent, averaging 0.6 percent at energies below the high energy cutoff of the mirror reflectivity, and are as high as 20.7 percent at the cutoff. We also discuss the approach to the final preflight calibration of the full AXAF flight mirror.

Kellogg, Edwin M.↗

OSO-8 X-ray observations of AM Herculis

Hard X-ray observations of the binary system AM Her were coincident with soft X-ray and ground-based optical measurements. In the 2-60 KeV band, variability was detected with an eclipse during phases 0.5 to 0.7 with respect to the 0. d 12892 period optical minima, synchronous with the known soft X-ray eclipse. The 2-60 KeV uneclipsed flux was 9.5 x 10 to the minus 10th power erg sq cm/sec, of which 86% lies above 10 keV. Thus AM Her contains a hard source located near the similarly eclipsed soft X-ray source. The X-ray data are interpreted in terms of thermal bremsstrahlung from accretion onto a white dwarf.

Swank, J. H.↗

OSO-8 X-ray observations of AM Herculis

Results are reported for hard X-ray observations of the binary system AM Her, which were coincident with soft X-ray and ground-based optical measurements. In the 2-60-keV band, variability was detected with an eclipse during phases 0.5 to 0.7 with respect to the 0.12892-day optical minima, synchronous with the known soft X-ray eclipse. The 2-60-keV uneclipsed flux was 9.5 by 10 to the -10th power erg/sq cm per sec, of which 86% lies above 10 keV. Thus, AM Her contains a hard source located near the similarly eclipsed soft X-ray source. The X-ray data are interpreted in terms of thermal bremsstrahlung from accretion onto a white dwarf.

Swank, J.↗

Evidence for a variable far-infrared source in NGC 6334

NGC 6334 has been mapped with a 40-250 micron photometer with 1 arcmin resolution. Six sources of far-infrared radiation have been detected. The second-strongest source was not detected in an earlier (2.7 years) 40-350 micron survey of the same region. This source is interpreted as a variable far-infrared source. The new source, located at the position of OH and H2O maser sources, is extended (0.7 arcmin FWHM) and has a bolometric luminosity of 190,000 solar luminosities and may represent a hitherto unobserved transient stage of protostellar collapse.

Mcbreen, B.↗

Source of O mode radio emissions from the dayside of Uranus

During the inbound trajectory toward Uranus, the Planetary Radio Astronomy instrument on Voyager 2 observed narrow-band smooth (n-smooth) emission at frequencies centered near 60 kHz and O-mode emission (the dayside source) in a frequency range narrowly confined around 160 kHz. Assuming empirical models of the plasma density for the dayside magnetosphere of Uranus, and using cold plasma theory together with observational constraints, ray-tracing calculations are performed to determine the source location of the O-mode emission. The dayside source appears to originate along magnetic field lines with a footprint near the north magnetic pole. Sources of nightside high-frequency broadband smooth (b-smooth) emission observed by Voyager after encounter are believed to exist near the conjugate footprint of these same field lines. This would indicate that the particle population supplying the free energy source has energies at least as high as a few keV.

Menietti, J. D.↗

Variable positron annihilation radiation from the galactic center region

HEAO 3 Cosmic Gamma-Ray Spectrometer evidence is presented for the existence of a time-varying, unshifted, narrow 511 keV line emission from the vicinity of the galactic center. Although uncertainties exist regarding the spatial extent of the features as well as its centroid, all data are consistent with emission from a single point source located at the galactic center. This interpretation would require a source luminosity of 2 x 10 to the 37th ergs/sec, and a positron annihilation rate of about 10 to the 43rd/sec. It is concluded that a variable source of positrons which could generate such an annihilation figure might be a massive black hole at the galactic center, as has been suggested by IR observations.

Riegler, G. R.↗

Lightning Studies Using VHF Waveform Data

Several atmospheric electricity studies were begun utilizing VHF lightning data obtained with the lightning detection and ranging system (LDAR) at the Kennedy Space Center (KSC). The LDAR system uses differences in the time of arrival of electromagnetic noise generated by the lightning process to seven antennas to calculate very accurate three dimensional locations of lightning. New software was developed to obtain the source location of multiple, simultaneous, and spatially separate lightning signatures. Three studies utilizing these data were begun this summer: (1) VHF observations of simultaneous lightning, (2) ground based VHF observations of transionospheric pulse pairs (TIPPs), and (3) properties of intra-cloud recoil streamers. The principal result of each of these studies are: (1) lightning commonly occurs in well separated (2-50 km) regions simultaneously, (2) large amplitude pairs of VHF pulses are commonly observed on the ground but had not been previously identified due to the large number of signals usually observed in the VHF noise of close lightning, and (3) the VHF Q-noise and pulse signatures associated with K-changes within intra-cloud lightning propagate at velocities of more than 10(exp 8) m/s. The interim results of these three studies are reviewed in this brief report.

Moldwin, Mark↗

The EUVE satellite survey database

The EUVE survey database contains fundamental science data for 9000 potential source locations (pigeonholes) in the sky. The first release of the Bright Source List is now available to the public through an interface with the NASA Astrophysical Data System. We describe the database schema design and the EUVE source categorization algorithm that compares sources to the ROSAT Wide Field Camera source list.

Craig, N.↗

Acquisition of and Access to Research Omics Data

Omics data are essential for understanding the myriad and complex effects of space environments on humans. To assure maximum benefit from these kinds of data, the NASA Human Research Program Data Management Plan stipulates that human omics data should be archived within and accessed through the NASA Life Sciences Portal (NLSP). The NLSP has the capability to acquire and provision access to omics (and other kinds of) research results for individual and ad-hoc groups of subjects at the direction of institutional review boards, or other authorizing bodies or individuals, per institutional, program and investigation-specific policies and procedures. However, because some single-subject omics data, like CT scans and other kinds of large, complex biomedical data, could be used to identify heretofore unknown risks to the subject’s health, or, in certain cases, be used to identify a subject, NASA Policy Directive 7170.1 describes various policies regarding the management of and access to “research genetic testing” data, which includes many kinds of omics data. For example, NPD 7170.1 prohibits access to human research genetic data by NASA personnel who make employment decisions for the subjects from whom the data were obtained. To meet the objective of acquiring research omics data for NLSP in compliance with the policies in NPD 7170.1 and other applicable NASA policies, we designed NOMADS (the NLSP Omics Multimodal Acquisition of Data System), a new component that supports the transfer of large research data files, including research genetic testing data, using one of several different transfer mechanisms. The choice of mechanism is made by the submitter of the data, with guiding information from the system, and is likely to often be determined in large part by the nature and source location of the data. For example, for small files where the source data files are not already stored in a cloud storage system, users are likely to prefer to transfer their data to the NLSP via a web browser. Conversely, for large sets of files already organized and stored in a cloud storage system, users may opt for NOMAD’s cloud-to-cloud transfer method. All omics datasets targeted for the NASA Life Sciences Data Archive must pass a variety of quality checks to ensure data integrity and adherence to the standards defined by the LSDA Data Submission Guidelines (DSG) (see https://nlsp.nasa.gov/explore/lsdahome/datasubmit). These include requirements that data are consistent with open standards established by the omics community. Non-compliant data will not be accepted however archivists are available to advise submitters on how to revise data submissions and re-submit until compliance is achieved. Following compliance with the LSDA DSG, omics data next undergo a variety of additional quality checks to ensure the data meet omics community standards. Domain specific Omics data quality control tools and techniques are continually evolving and linked to the advancements in omics assays utilized and thus, the tools and techniques utilized by the LSDA for data quality control and validation will need to be sustained accordingly. All human omics data will be access controlled according to the policies described above, and requiring IRB approval for any additional access grants once the data are acquired (including access for analysis using the NLSP workspace tools).

Omics↗

Acquisition of and Access to Research Omics Data

Omics data are essential for understanding the myriad and complex effects of space environments on humans. To assure maximum benefit from these kinds of data, the NASA Human Research Program Data Management Plan stipulates that human omics data should be archived within and accessed through the NASA Life Sciences Portal (NLSP). The NLSP has the capability to acquire and provision access to omics (and other kinds of) research results for individual and ad-hoc groups of subjects at the direction of institutional review boards, or other authorizing bodies or individuals, per institutional, program and investigation-specific policies and procedures. However, because some single-subject omics data, like CT scans and other kinds of large, complex biomedical data, could be used to identify heretofore unknown risks to the subject’s health, or, in certain cases, be used to identify a subject, NASA Policy Directive 7170.1 describes various policies regarding the management of and access to “research genetic testing” data, which includes many kinds of omics data. For example, NPD 7170.1 prohibits access to human research genetic data by NASA personnel who make employment decisions for the subjects from whom the data were obtained. To meet the objective of acquiring research omics data for NLSP in compliance with the policies in NPD 7170.1 and other applicable NASA policies, we designed NOMADS (the NLSP Omics Multimodal Acquisition of Data System), a new component that supports the transfer of large research data files, including research genetic testing data, using one of several different transfer mechanisms. The choice of mechanism is made by the submitter of the data, with guiding information from the system, and is likely to often be determined in large part by the nature and source location of the data. For example, for small files where the source data files are not already stored in a cloud storage system, users are likely to prefer to transfer their data to the NLSP via a web browser. Conversely, for large sets of files already organized and stored in a cloud storage system, users may opt for NOMAD’s cloud-to-cloud transfer method. All omics datasets targeted for the NASA Life Sciences Data Archive must pass a variety of quality checks to ensure data integrity and adherence to the standards defined by the LSDA Data Submission Guidelines (DSG) (see https://nlsp.nasa.gov/explore/lsdahome/datasubmit). These include requirements that data are consistent with open standards established by the omics community. Non-compliant data will not be accepted however archivists are available to advise submitters on how to revise data submissions and re-submit until compliance is achieved. Following compliance with the LSDA DSG, omics data next undergo a variety of additional quality checks to ensure the data meet omics community standards. Domain specific Omics data quality control tools and techniques are continually evolving and linked to the advancements in omics assays utilized and thus, the tools and techniques utilized by the LSDA for data quality control and validation will need to be sustained accordingly. All human omics data will be access controlled according to the policies described above, and requiring IRB approval for any additional access grants once the data are acquired (including access for analysis using the NLSP workspace tools).

Omics↗

Thermal Inspection of Low Emissivity Surfaces Using a Pulsed Light Emitting Diodes (PLED) Heat Source

Thermal inspections of a structure typically utilize a flash or quartz lamp heat source located on the same side of an infrared camera. The heat source provides light energy for heating while the infrared camera measures the surface transient temperature response. The inspection can be difficult for low emissivity surfaces for several reasons. First, the high intensity light can reflect off the surface and cause “burn-in” to the camera’s detector. The “burn-in” can take time for the sensors to recover and potentially damage the detector. Secondly, the heat source after pulsing, has a transient cool down component. The cool down component can be reflected and therefore superimposed over the structure’s thermal response which can cause an error (false defect indications) in the inspection. Lastly, the heat source is spectrally broad and therefore while heating, infrared components of the heat source can produce non-uniformity in the measured temperature field. Typically for the inspection of reflective surfaces, paint or other emissivity enhancing coatings are applied before inspection. In this paper, a pulsed light emitting diodes (PLED) heat source is used. The PLED heat source is spectrally narrow, contained within the visible band, and therefore not detectable by the infrared camera. The PLED heat source is configured to reduce any transient cool down components that could produce false defect indications. The PLED thermal inspections are compared to commercially available flash thermography inspections on unpainted aluminum samples with simulated corrosion and additively manufactured Ti-6AL-4V metal specimens.

thermal nondestructive evaluation↗

Thermal Inspection of Low Emissivity Surfaces Using a Pulsed Light Emitting Diodes (PLED) Heat Source

Thermal inspections of a structure typically utilize a flash or quartz lamp heat source located on the same side of an infrared camera. The heat source provides light energy for heating while the infrared camera measures the surface transient temperature response. The inspection can be difficult for low emissivity surfaces for several reasons. First, the high intensity light can reflect off the surface and cause “burn-in” to the camera’s detector. The “burn-in” can take time for the sensors to recover and potentially damage the detector. Secondly, the heat source after pulsing, has a transient cool down component. The cool down component can be reflected and therefore superimposed over the structure’s thermal response which can cause an error (false defect indications) in the inspection. Lastly, the heat source is spectrally broad and therefore while heating, infrared components of the heat source can produce non-uniformity in the measured temperature field. Typically for the inspection of reflective surfaces, paint or other emissivity enhancing coatings are applied before inspection. In this paper, a pulsed light emitting diodes (PLED) heat source is used. The PLED heat source is spectrally narrow, contained within the visible band, and therefore not detectable by the infrared camera. The PLED heat source is configured to reduce any transient cool down components that could produce false defect indications. The PLED thermal inspections are compared to commercially available flash thermography inspections on unpainted aluminum samples with simulated corrosion and additively manufactured Ti-6AL-4V metal specimens.

thermal nondestructive evaluation↗