Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solution design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Life Support Systems for a New Lunar Lander

A life support system concept has been developed for a new NASA lunar lander concept. The ground rules and assumptions driving the design of this vehicle are different from the Constellation Altair vehicle, and have led to a different design solution. For example, this concept assumes that the lander vehicle arrives in lunar orbit independently of the crew. It loiters in lunar orbit for months before rendezvousing with the Orion Multi-Purpose Crew Vehicle (MPCV), resulting in the use of solar power for this new lander, rather than fuel cells that provided product water to the life support system in the Altair vehicle. Without the need to perform a single Lunar Orbit Insertion burn for both the lander and the MPCV, the modules do not have to be centered in the same way, so the new lander has a smaller ascent module than Altair and a large habitat rather than a small airlock. This new lander utilizes suitport technology to perform EVAs from the habitat, which leads to significantly different requirements for the pressure control system. This paper describes the major trades and resulting concept design for the life support system of a new lunar lander concept.

Anderson, Molly↗
NASA NTRS2012

Life Support Systems for a New Lunar Lander

A life support system concept has been developed for a new NASA lunar lander concept. The ground rules and assumptions driving the design of this vehicle are different from the Constellation Altair vehicle, and have led to a different design solution. For example, this concept assumes that the lander vehicle arrives in lunar orbit independently of the crew. It loiters in lunar orbit for months before rendezvousing with the Orion Multi-Purpose Crew Vehicle (MPCV), resulting in the use of solar power for this new lander, rather than fuel cells that provided product water to the life support system in the Altair vehicle. Without the need to perform a single Lunar Orbit Insertion burn for both the lander and the MPCV, the modules do not have to be centered in the same way, so the new lander has a smaller ascent module than Altair and a large habitat rather than a small airlock. This new lander utilizes suitport technology to perform EVAs from the habitat, which leads to significantly different requirements for the pressure control system. This paper describes the major trades and resulting concept design for the life support system of a new lunar lander concept. I

Anderson, Molly↗
NASA NTRS2011

Scoring Dawg Core Breakoff and Retention Mechanism

This novel core break-off and retention mechanism consists of a scoring dawg controlled by a set of two tubes (a drill tube and an inner tube). The drill tube and the inner tube have longitudinal concentric holes. The solution can be implemented in an eccentric tube configuration as well where the tubes have eccentric longitudinal holes. The inner tube presents at the bottom two control surfaces for controlling the orientation of the scoring dawg. The drill tube presents a sunk-in profile on the inside of the wall for housing the scoring dawg. The inner tube rotation relative to the drill tube actively controls the orientation of the scoring dawg and hence its penetration and retrieval from the core. The scoring dawg presents a shaft, two axially spaced arms, and a tooth. The two arms slide on the control surfaces of the inner tube. The tooth, when rotated, can penetrate or be extracted from the core. During drilling, the two tubes move together maintaining the scoring dawg completely outside the core. After the desired drilling depth has been reached the inner tube is rotated relative to the drill tube such that the tooth of the scoring dawg moves toward the central axis. By rotating the drill tube, the scoring dawg can score the core and so reduce its cross sectional area. The scoring dawg can also act as a stress concentrator for breaking the core in torsion or tension. After breaking the core, the scoring dawg can act as a core retention mechanism. For scoring, it requires the core to be attached to the rock. If the core is broken, the dawg can be used as a retention mechanism. The scoring dawg requires a hard-tip insert like tungsten carbide for scoring hard rocks. The relative rotation of the two tubes can be controlled manually or by an additional actuator. In the implemented design solution the bit rotation for scoring was in the same direction as the drilling. The device was tested for limestone cores and basalt cores. The torque required for breaking the 10-mm diameter limestone cores was 5 to 5.8 lb-in. (0.56 to 0.66 N-m).

Badescu, Mircea↗
NASA NTRS1972

The space shuttle and its uses.

The development of reusable space-shuttle vehicles has been made practical by the availability of improved staged-combustion engines and durable thermal protection systems. A two-state launch configuration with fully reusable booster and orbiter elements is considered to be the best design solution, and size specifications for such a vehicle are examined as a function of launch costs. Significant vehicle characteristics are explained in terms of cargo bay dimensions, cross-range maneuvering capability, mission duration requirements, engine characteristics, and acceleration constraints. Shuttle flight activities include satellite deployment and repair, sortie missions for short-duration research purposes, and space station support operations. Phases of the development program are outlined, and structural details of several candidate space shuttle concepts are illustrated.

Mathews, C. W.↗
NASA NTRS1973

Optimum TPS Design with Rei-mullite

It has been shown that a ceramic mullite fiber/mullite insulation has adequate margins-of-safety based on minimum strengths for the critical thermostructural conditions of the shuttle mission. Introduction into the design of the new lower density foam bond material provides cold soak and cold entry capability at 116 K (-250 F). Finally, design solutions to the coating cracking tendencies have been identified and the solution analytically verified with three dimensional thermostructural analysis.

Hess, T. E.↗
NASA NTRS1973

OSO-7 spectroheliograph mechanisms

The OSO-7 Orbiting Solar Observatory was launched on September 29, 1971. One of the two main sun pointing instruments aboard was a spectroheliograph for monitoring extreme ultraviolet and X-ray radiation from the sun. The instrument has been operating successfully in orbit for approximately two years. The design solution to each of the mechanism tasks is described. Also described are certain developmental problems and their solutions which led to the ultimate mission success.

Matteo, D. N.↗
NASA NTRS1971

Advancement of proprotor technology. Task 2: Wind-tunnel test results

An advanced-design 25-foot-diameter flightworthy proprotor was tested in the NASA-Ames Large-Scale Wind Tunnel. These tests, have verified and confirmed the theory and design solutions developed as part of the Army Composite Aircraft Program. This report presents the test results and compares them with theoretical predictions. During performance tests, the results met or exceeded predictions. Hover thrust 15 percent greater than the predicted maximum was measured. In airplane mode, propulsive efficiencies (some of which exceeded 90 percent) agreed with theory.

Source record↗
NASA NTRS1974

Skylab biomedical hardware development

The development of hardware to support biomedical experimentation and operations in the Skylab vehicle presented unique technical problems. Designs were required to enable the accurate measurement of many varied physiological parameters and to compensate for zero g such that uninhibited equipment operation would be possible. Because of problems that occurred during the orbital workshop launch, special tests were run and new equipment was designed and built for use by the first Skylab crew. Design concepts used in the development of hardware to support cardiovascular, pulmonary, vestibular, body, and specimen mass measuring experiments are discussed. Additionally, major problem areas and the corresponding design solutions, as well as knowledge gained that will be pertinent for future life sciences hardware development, are presented.

Huffstetler, W. J., Jr.↗
NASA NTRS1977

Application of polynomial techniques to multivariable control of jet engines

This paper describes a complete case study of the application of the theory of minimal design to multivariable control of jet engines. The minimal-design problem is approached from the viewpoint of polynomial modules, and computational experience with PL/I and FORMAC-PL/I software is discussed. The complete minimal-design solution exhibits flexibilities not apparent in early industry studies, and a matrix approach to pole assignment can be used to advantage in this situation.

Gejji, R. R.↗
NASA NTRS1979

Planetary mission requirements, technology and design considerations for a solar electric propulsion stage

High energy planetary missions such as comet rendezvous, Saturn orbiter and asteroid rendezvous require development of a Solar Electric Propulsion Stage (SEPS) for augmentation of the Shuttle-IUS. Performance and functional requirements placed on the SEPS are presented. These requirements will be used in evolution of the SEPS design, which must be highly interactive with both the spacecraft and the mission design. Previous design studies have identified critical SEPS technology areas and some specific design solutions which are also presented in the paper.

Cork, M. J.↗
NASA NTRS1979

The MOD-1 steel blade

The design, development, fabrication, testing, and transport of two 100 foot metal blades for the MOD-1 WTS are summarized. Because the metal blade design was started late in the MOD-1 system development, many of the design requirements (allocations) were restrictive for the metal blade concept, particularly the maximum weight requirement. The design solutions required to achieve the weight goal resulted in a labor intensive (expensive) fabrication, particularly for a quantity of only two blades manufactured using minimal tooling.

Vanbronkhorst, J.↗
NASA NTRS1979

Low-cost point-focus solar concentrator, phase 1

The results of the preliminary design study for the low cost point focus solar concentrator (LCPFSC) development program are presented. A summary description of the preliminary design is given. The design philosophy used to achieve a cost effective design for mass production is described. The concentrator meets all design requirements specified and is based on practical design solutions in every possible way.

Nelson, E. V.↗
NASA NTRS1980

Modular space structures

The Extendable Tetrahedral Truss orbiting antenna concept, comprising the use of prefabricated, automatically deployable lattice structures and their subsequent assembly into larger structures suitable for microwave antenna use, is described. It is assumed that the Space Shuttle Orbiter payload bay will be able to accommodate only modular portions of the structural system required, and that the Space Shuttle crew will furnish the manual labor entailed by orbital assembly. It is concluded that a deployable beam module system may be a more elegant design solution than the alternative triangular-module system.

Vaughan, D. H.↗
NASA NTRS1980

Design, fabrication and test of a complex helicopter airframe section

A design solution is developed for the fabrication of an all-composite helicopter airframe cabin roof structure. Although this is inherently a complex structure, the parts count has been minimized by the avoidance of many mechanical fasteners, and a weight reduction of 26% has been obtained. The reduction of parts and elimination of mechanical fasteners will also result in a lowering of labor costs. The bonded graphite/epoxy elements of the structure employed aluminum tooling with control on all mating surfaces to yield accurate bond lines. A summary of static test results is presented for the basic structure and for the structure with mechanically fastened skin stiffeners. It is shown that the shear buckles caused the skin to peel from the stiffeners at about 960 lb/in. shear flow, calling for the addition of stiffeners with more bond area.

Rich, M. J.↗
NASA NTRS1981

Progress in supersonic cruise technology

It is reported that nine years of NASA research have yielded significant design solutions in such matters pertaining to large supersonic cruise vehicles as aerodynamics, structures, propulsion, noise reduction, takeoff and landing procedures, and advanced configuration concepts. Attention is given to the incremental performance gains achieved over the years (with the Concorde SST as baseline reference), arrow wing planform performance potential, superplastic forming/diffusion bonding of titanium alloy primary structures, advanced engine cycles, twin-fuselage high-capacity configurations, and the potential military payoff of SST research. It is concluded that the greatest promise for future research and development lies in fiber-reinforced, high-temperature metal structures and the twin-fuselage configuration.

Driver, C.↗
NASA NTRS1982

The design and development of an end effector for the shuttle remote manipulator system

The design requirements, the design, and qualification and development test problems encountered on the Remote Manipulator End Effector are described. The constraints and interfaces with the arm, the Orbiter, and the payload are identified. The design solution to meet the requirements is a unique device that provides a soft-docking feature termed capture and a hard-docking feature termed rigidization.

Daniell, R. G.↗
NASA NTRS1982

A new design approach to achieve a minimum impulse limit cycle in the presence of significant measurement uncertainties

A new design was developed for the Space Shuttle Transition Phase Digital Autopilot to reduce the impact of large measurement uncertainties in the rate signal during attitude control. The signal source, which was dictated by early computer constraints, is characterized by large quantization, noise, bias, and transport lag which produce a measurement uncertainty larger than the minimum impulse rate change. To ensure convergence to a minimum impulse limit cycle, the design employed bias and transport lag compensation and a switching logic with hysteresis, rate deadzone, and 'walking' switching line. The design background, the rate measurement uncertainties, and the design solution are documented.

Martin, M. W.↗