Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solution deposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effect of deposition rate on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by laser engineered net shaping

Laser engineered net shaping (LENS) is an additive manufacturing technique for fabricating and repairing metallic components. However, the relationships between its process parameters and the resulting mechanical properties of alloys such as 17-4 precipitation-hardening (PH) stainless steel require further investigation to enable reliable application. This study examines the specific effect of LENS deposition rate on the microstructure and mechanical properties of 17-4 PH stainless steel. Specimens were fabricated at two different deposition rates (8.47 and 9.31 mm s−1), subjected to subsequent solution and H900 aging treatment, and then evaluated via tensile testing, hardness measurements, and microscopy. A higher deposition rate results in a finer grain structure but increased porosity, leading to greater ultimate tensile strength (∼1294 MPa) yet lower ductility (strain at failure ∼5.8%) compared to the slower deposition rate (∼1266 MPa, ∼9.0% strain). Hardness follows the same trend as tensile strength. Tensile fracture surfaces for both conditions exhibited a mixed mode of ductile dimples and brittle quasi-cleavage regions, with chromium/silicon oxide particles identified within dimples. Complementary finite element modeling indicates that small void fractions primarily reduce ductility by enhancing localized plasticity, with only a marginal decrease in tensile strength. These integrated experimental and numerical results elucidate the mechanical properties linked to deposition rate, providing insight into tailoring LENS processes to achieve desired properties of 17-4 PH stainless steel.

17-4 PH stainlesssteel↗
DOE OSTI2022

Growth mechanisms of large, faceted crystals grown from solutions

Here, the paper describes optical techniques and methods used to study growth mechanisms and phenomena occurring on multiple faces of real bulk crystals grown from aqueous and organic solutions. Using examples of ionic KDP and molecular trans-stilbene crystals, it shows how in-situ and ex-situ surface observations can be applied to identify growth structures characteristic for the dislocation, two-dimensional (2D), and 3D cluster deposition mechanisms. Results are analyzed and applied to understanding of defects origins and methods for their elimination in practical growth of large, high optical quality crystals.

2D growth mechanism↗
DOE OSTI2021

SURFACE FINISHING AND ELECTROLESS NICKEL PLATING OF ADDITIVELY MANUFACTURED (AM) METAL COMPONENTS

This study investigates the application of electroless nickel deposition on additively manufactured stainless steel samples. Current additive manufacturing (AM) technologies produce metal components with a rough surface. Rough surfaces generally exhibit fatigue characteristics, increasing the probability of initiating a crack or fracture to the printed part. For this reason, the direct use of as-produced parts in a finished product cannot be actualized, which presents a challenge. Post-processing of the AM parts is therefore required to smoothen the surface. This study analyzes chempolish (CP) and electropolish (EP) surface finishing techniques for post-processing AM stainless steel components CP has a great advantage in creating uniform, smooth surfaces regardless of size or part geometry EP creates an extremely smooth surface, which reduces the surface roughness to the sub-micrometer level. In this study, we also investigate nickel deposition on EP, CP, and as-built AM components using electroless nickel solutions. Electroless nickel plating is a method of alloy treatment designed to increase manufactured component's hardness and surface resistance to the unrelenting environment. The electroless nickel plating process is more straightforward than its counterpart electroplating.. We use low-phosphorus (2-5% P), medium-phosphorus (6-9% P), and high-phosphorus (10-13% P). These Ni deposition experiments were optimized using the L9 Taguchi design of experiments (TDOE), which compromises the prosperous content in the solution, surface finish, plane of the geometry, and bath temperature. The pre-and post-processed surface of the AM parts was characterized by KEYENCE Digital MicroscopeVHX-7000 and Phenom XL Desktop SEM. The experimental results show that electroless nickel deposition produces uniform Ni coating on the additively manufactured components up to 20 μm per hour. Mechanical properties of as-built and Ni coated AM samples were analyzed by applying a standard 10 N scratch test. Nickel coated AM samples were up to two times scratch resistant compared to the as-built samples. This study suggests electroless nickel plating is a robust viable option for surface hardening and finishing AM components for various applications and operating conditions.

Keywords: additive manufacturing, fatigue, chempol↗
DOE OSTI2025

Numerical design considerations for vapor transport deposition of metal-halide perovskite thin films

While metal-halide perovskites (MHPs) offer high efficiency and potential application in single junction and tandem solar cells, challenges remain in translating solution-based methods to commercial-scale production. Vapor transport deposition (VTD) offers advantages such as precise control over film composition and purity, as well as the possibility of achieving high thin film deposition rates for scale-up. In this work, a numerical model is developed to simulate the deposition process, analyzing the impact of parameters including source material temperature, carrier gas and dilution gas flow rates, and chamber pressure to optimize deposition rates and film uniformity. Geometrical parameters, such as throw distance, are also found to significantly affect rate and uniformity. Furthermore, the modeling results presented here offer valuable insight for improving the scalability of VTD for the processing of metal-halide perovskites.

Chemical vapor deposition↗
DOE OSTI2021

Cesium Batch Contact Equilibrium Testing of Crystalline Silicotitanate (CST) Sieve Cuts in SRS Average Simulant and Examination of CST Samples Aged in Caustic and Simulant in Support of Tank Closure Cesium Removal 1A (TCCR-1A)

Batch contact testing to determine cesium equilibrium loading on Crystalline Silicotitanate ion exchange media in Savannah River Site Average Waste Simulant at 25 °C indicated that smaller diameter particles isolated by sieving pretreated CST media may load slightly higher (<10%) amounts of cesium, though the differences are within analytical uncertainty. In addition, ion exchange media sub-samples stored in 2-4 M NaOH and caustic simulant solutions for ~2.5 years were examined by optical microscopy and the 3 M NaOH sample was also analyzed to determine whether changes in the particle size distribution occurred during storage. No visual indications of particle attrition or agglomeration were observed for any sample. Particle size analysis indicated that a slight decrease occurred in the average particle diameter following contact with 3 M NaOH (541 µm average diameter versus 566 µm for the pretreated CST prior to contact). A small increase (from 0 to <0.5 wt. %) in the number of particles ranging from 271 and 322 µm was also observed for the CST sample contacted with 3 M NaOH relative to a sample of the original pretreated material. However, this small change could be due to sub-sampling differences or analytical uncertainty. It does not appear that small particles are formed to a significant degree during CST caustic contact or that small particles which do form (presumably from attrition of larger particles during pretreatment) load significantly more cesium than the bulk material. Minimal other negative consequences were observed associated with CST extended caustic or simulant contact, except for the tendency for more concentrated salt solutions to form some salt crystals which deposit on the media over time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Mk-IV Salt Crystallization Hot Finger Apparatus for Partitioning Used Electrorefiner Salt

Electrorefining is a controlled redox process used to regulate the behavior of ionic species. Through this process, metals can be deposited onto a cathode from an electrolyte solution in a controlled manner. The Mk-IV electrorefiner (Mk-IV ER) at Idaho National Laboratory is an engineering-scale, molten salt-based electrorefining cell that has been used for decades to recover metallic uranium from spent fuel. As a result, highly stable fission product chlorides have accumulated in the electrolyte. This accumulation results in changes to the salt’s properties, such as melting temperature, thermal conductivity, and density, as well as elevated product impurity and fissile materials criticality margin. These factors prompt the need for a salt regeneration process, such as melt-crystallization and species drawdown. This work focuses on providing a conceptual design to regenerate ER salt from used Mk-IV-ER salt in-situ, while minimizing salt waste volumes by concentrating the fission products in a final processed salt heal. We propose using a hot-finger crystallization apparatus design to fractionally crystallize salt in the Mk-IV-ER head space (or baffle space), allowing the collection of solid and liquid fractions. By using a cup-drain design, the used salt will be allowed to slowly solidify on the walls of a stainless-steel cup. The apparatus drain plug will then open to allow the liquid salt phase to drain to a lower cup, effectively separating the liquid phase from the solid phase. Under the hypothesis that the liquid phase salt concentrates the fission products, which is under examination in the accompanying work package, this separation allows the recovered solid salt to be reused while minimizing the high-level salt waste volume of used ER salt.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Understanding Solution State Conformation and Aggregate Structure of Conjugated Polymers via Small Angle X-ray Scattering

Donor-acceptor (D-A) conjugated polymers are high-performance organic electronic materials that exhibit complex aggregation behavior. Understanding the solution state conformation and aggregation of conjugated polymers is crucial for controlling morphology during thin-film deposition and the subsequent electronic performance. However, a precise multiscale structure of solution state aggregates is lacking. Here, we present an in-depth small-angle X-ray scattering (SAXS) analysis of the solution state structure of an isoindigo-bithiophene-based D-A polymer (PII-2T) in chlorobenzene and decane as our primary system. Modeling the system as a combination of hierarchical fibrillar aggregates mixed with dispersed polymers, we extract information about conformation and multiscale aggregation and also clarify the physical origin of features often observed but unaddressed or misinterpreted in small-angle scattering patterns of conjugated polymers. The persistence length of the D-A polymer extracted from SAXS agrees well with a theoretical model based on the dihedral potentials. Additionally, we show that the broad high q structure factor peak seen in scattering profiles can be attributed to lamellar stacking occurring within the fibril aggregates and that the low q aggregate scattering is strongly influenced by the polymer molecular weight. Overall, the SAXS profiles of D-A polymers in general exhibit a sensitive dependence on the co-existence of fibrillar aggregate and dispersed polymer chain populations. We corroborate our findings from SAXS with electron microscopy of freeze-dried samples for direct imaging of fibrillar aggregates. Finally, we demonstrate the generality of our approach by fitting the scattering profiles of a variety of D-A polymers based on thieno-isoindigo (PTII-2T), diketopyrrolopyrrole (DPP2T-TT, DPP-BTZ, PDPP2FT-C- 16 ), naphthalenediimide (P(NDI2OD-T2)), and a conjugated block copolymer P3HT-b-DPPT-T. The results presented here establish a picture of the D-A polymer solution state structure and provide a general method of interpreting and analyzing their scattering profiles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Atomic layer deposition and its derivatives for extreme ultraviolet (EUV) photoresist applications

Solution-processed photoresists have been forerunners in semiconductor patterning for decades. Even with the drastic reduction in photolithography wavelength, traditional spin-on resists still support the fabrication of the most advanced, sub-5 nm node logic and memory devices using EUV lithography (EUVL) (λ = 13.5 nm). However, trade-off between resolution, sensitivity, and roughness in the conventional resists pose a critical challenge in the race towards device downscaling to 1 nm node. While great efforts are being made to improve spin-on EUV photoresist performance, there has been emergence of new approaches focused on developing novel resists via vapor-phase processing routes, such as atomic layer deposition (ALD) and its analogs. This review summarizes recent advances in EUVL photoresist development based on ALD and its derivative techniques, which include ALD-based inorganic–organic dry resists and hybrid resists synthesized by infiltrating conventional spin-on resists. Despite being in the early stage, initial studies have shown the great potential of ALD applications in EUVL photoresist development.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Bypassing sulfides: comparing the morphology and performance of solution processed Cu(In,Ga)Se 2 films prepared via two selenide molecular precursor routes

Solution-processing of thin-film photovoltaics offers an alternative to vacuum-deposition based approaches. The amine–thiol reactive solvent system has become a focal point for the solution-processing of chalcogenide species, owing to the convenience of precursor preparation and comparatively high performance of prepared devices. Selenide species prepared via the amine–thiol route typically progress through a sulfide intermediate phase, and as such are commonly afflicted with sulfur and carbon impurities along- side the presence of a carbonaceous fine-grained layer. Here, two routes of preparing films directly to a selenide phase are examined; first by the co-dissolution of selenium in an amine–thiol solution and second via the novel use of reactive alkylammonium polyselenides. Lamella are cut from these selenide precursor films and final devices, and STEM-EDX and TEM are used to characterize film morphology and secondary phases. A champion device efficiency of 11.2% is reported for the novel polyselenide route, and clear paths of improvement are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Manipulating meso-scale solvent structure from Pd nanoparticle deposits in deep eutectic solvents

Deep Eutectic Solvents (DESs) are complex solutions that present unique challenges compared to traditional electrolytes. Unlike most electrolytes and ionic liquids, DESs have delicate hydrogen bond networks that are responsible for their highly sensitive compositional dependence on the melting point. Prior work has demonstrated unique nanoscale structure both experimentally and theoretically that brings both challenges and opportunities to their adoption in traditional electrochemical processes. In this study, we use in-situ sample-rotated ultra-small angle X-ray scattering to resolve the near-interface solvent structure after electrodepositing Pd nanoparticles onto a glassy carbon electrode in choline chloride:urea and choline chloride:ethylene glycol DESs. Our results indicate that solvent structure can be observed on the meso-scale in the choline chloride:urea and choline chloride:ethylene glycol systems. Importantly, this extended solvent structure peaks at -0.5 V (vs. Ag/AgCl) and decreases slightly with higher overpotentials during Pd electrodeposition. Experimentally, the nature of this structure is more pronounced in the ethylene glycol system, as evidenced by both the X-ray scattering as well as the electrochemical impedance spectroscopy (EIS). Here, molecular dynamics simulations and dipolar orientation analysis reveal that chloride delocalization near the Pd interface and long-range interactions between the choline and each hydrogen bond donor are very different and qualitatively consistent with the experimental data. These results show how the long-range solvent-deposit interactions can be tuned by changing the hydrogen bond donor in the DES and the applied potential.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Engineering Perovskite Precursor Inks for Scalable Production of High‐Efficiency Perovskite Photovoltaic Modules

Abstract Blade coating of perovskite solar cells (PSCs) and modules has progressed considerably toward the industrial production of perovskite photovoltaics. Developing stable perovskite precursors is critical for achieving uniform coating over large areas. Here, the engineering of a perovskite precursor solution consisting of 2‐methoxyethanol (2‐Me) and 1,3‐dimethyl‐imidazolidinone (DMI) with superior intermediate phase stability that enables scalable production of efficient perovskite solar modules is reported. With this perovskite precursor solution, uniform and pinhole‐less perovskite film is deposited over a large area of > 100 cm 2 and higher‐efficiency PSCs and modules are obtained. The best‐performing unit cell and module with n‐i‐p configuration reach power conversion efficiencies of 23.4% and 20.1%, respectively. Additionally, a series of non‐destructive metrology methods, such as spectroscopic ellipsometry, hyperspectral photoluminescence, electroluminescence, and laser beam‐induced current mapping, are employed to assess and guide the development the blade‐coated perovskite modules. This results show that rational engineering of precursor inks for blade coating is promising for the scalable production of efficient perovskite solar modules.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Design of an Additively Manufactured Recuperator With 800 °C Inlet Temperature for sCO2 Power Cycle Application

Abstract Recuperators with design temperatures at and above 800 °C can further increase the thermal efficiency of supercritical CO2 power cycles by enabling higher turbine exhaust temperatures. Mar-M247 is a well-suited nickel-based superalloy for high temperature service due to its high creep strength that prevents excessive material thickness being required for pressure containment. Additive manufacturing using a high-speed laser-directed energy deposition (L-DED) process presents a promising solution, with build trials demonstrating the ability to produce nonconventional flow channels for enhanced heat transfer. A design process is presented that includes aerothermal and mechanical evaluation to maximize performance within the constraints of the manufacturing process. A 2-D heat transfer network and pressure drop code allows prediction of flow distribution and its effect on overall thermal performance. Established literature correlations, along with CFD simulation, inform the prediction of heat transfer coefficients and friction factors for the flowpaths and enhancement features in the heat exchanger core. Mechanical evaluation using finite element analysis (FEA) modeling with the intent of the ASME Boiler & Pressure Vessel Code (BPVC) Section VIII, Div. 2 assesses the operational safety of the design. The detailed design features annular finned passages that take advantage of helical flow paths to distribute the flow from separated headers to shared heat transfer surfaces. Performance predictions for the recuperator at a 50 kW scale provide insights into the feasibility of the additively manufactured (AM) process to produce recuperators on a commercial scale that extend existing operating envelopes.

Engineering↗
DOE OSTI2020

Development of Perovskite (PVSK) Technology Related to Solar Cell Manufacturing Equipment (CRADA CRD-18-733 Final Report)

This CRADA between Energy Everywhere and NREL is to develop a process to fabricate flexible photovoltaic modules using a solution coated PVSK absorber with interlayers comprising materials deposited by economically feasible methods. Energy Everywhere™ will replicate and scale this process in Berkeley, California where it will ultimately commercialize the process, fabrication equipment, and PV modules.

14 SOLAR ENERGY↗
DOE OSTI2024

Electrochemically Assisted Single Crystal Growth of Reduced Preyssler Polyoxometalates Decorated with M 2+ ( M = Co, Ni) and Cubane–Like Ni 4 O 4 Units

Polyoxometalates (POMs) are of great interest to the scientific community, and their reduction and nucleation have been well–established by multi–step techniques. The present study develops an electrochemical approach for simultaneous reduction and nucleation of polyoxometalate–containing solids. Herein we report crystal growth of reduced Preyssler polyoxotungstate–based (anionic formula [NaP 5 W 30 O 110 ] 14– ) new crystalline solids made of Preyssler anions interlinked by Co 2+ and Ni 2+ ions. Crystal nucleation and in situ reduction were achieved at room temperature using a two silver wire electrode setup in various aqueous solutions under constant applied potentials. The POM material was deposited on the cathode, and its structure was characterized by X–ray diffraction techniques. The primary structure type observed involves POMs decorated by disordered Co 2+ /Ni 2+ octahedra and fused into 1–D pillars by additional Co 2+ /Ni 2+ octahedra. Additionally, a secondary phase was observed in the Ni–based reactions, where reduced Preyssler anions are decorated by Ni 4 O 4 cubane–like units. To understand the electrochemical process, polarization curves of the electrolyte solutions are presented, suggesting an applied potential best suited for crystal growth. The work highlights the effectiveness of an electrochemical pathway where nucleation and simultaneous reduction of POMs can make novel reduced POM solids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Synthesis and Morphological Characterization of Electroless-Deposited Ni-P Coatings on Diamond Abrasives

Deposition of a coating on rough surfaces faces unique challenges due to the complexity of substrate morphology. In the present research, electroless deposition of a Ni-P coating was successfully deposited on diamond particles. Microtomography was conducted to study the deposition mechanisms. It revealed that the coating coverage rate on diamond particles was affected by the synergistic action of the deposition time, substrate morphology, and hypophosphite concentration. The best coverage was achieved in a solution with 0.2 mol/L hypophosphite. Two major morphological features of the coating: nodular and smooth, were influenced by the deposition parameters, coating integrity, and substrate morphology. The failure was seen in fractured and peeled off coatings. It was due to residual stress produced by the coalescing of crystallites during the deposition. This failure mechanism explains the tendency of coating fracture at three morphological features of the substrate. This work is beneficial to semiconductor manufacturing where effective cutting in chip fabrication is essential.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Energetics of hydroxylbastnäsite solid solutions, La 1-$\chi$ Nd $\chi$ CO 3 OH

Bastnäsites (LnCO 3 (F,OH)) are a group of common rare earth elements (REE)-bearing minerals and are one of the primary global sources of REE. Due to the chemical similarities among REE, bastnӓsites tend to occur as solid solutions instead of end members in REE containing ores. To better understand the processes and the mechanisms of formation of such deposits, it is essential to determine the thermodynamic properties of bastnӓsites, including hydroxylbastnӓsite (LnCO 3 OH) solid solutions. In this work, we performed detailed structural and calorimetric investigations on synthetic hexagonal La–Nd hydroxylbastnӓsite (La 1-$\chi$ NdCO 3 OH, $\chi$ = 0, 0.25, 0.5, 0.75, 1) solid solutions. X-ray diffraction confirms the crystal structure of the solid solution series in the $\ P$6 space group, and pair distribution function (PDF) analysis reveals local bonding environments characterized by three different types of 9-coordinated metal-oxygen polyhedra. Unit cell parameters of La1–xNdxCO3OH exhibit a nearly linear relation with the Nd content x, suggesting a random distribution of La and Nd in the structure. Their standard enthalpies of formation (Δ$\ H$° f ) were determined by high temperature oxide melt drop solution calorimetry, from which the enthalpies of mixing (Δ$\ H$ mix ) were derived. The Δ$\ H$ mix can be fitted by a regular solution model with an interaction parameter of 12.58 ± 0.16 kJ/mol, suggesting enthalpic metastability of La1–xNdxCO3OH relative to the two endmembers. Combining entropy and enthalpy, we further estimated the Gibbs free energies of mixing (Δ$\ G$ mix ) at relevant temperatures, revealing favorable temperatures under which the intermediate La 1-$\chi$ NdCO 3 OH phases can be stabilized. Such entropy-driven stabilization, as is consistent with our geochemical modeling results, may explain the enhancement of thermal stability of the solid solutions in nature. Additionally, the temperature range constrained from this study may be used to estimate the thermal history of REE bastnӓsite deposit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Localized Heterogeneous Nucleation for Vapor‐Assisted Sequential Deposition of Metal Halide Perovskites

Vapor-assisted hybrid two-step deposition, which combines thermally evaporated inorganic layers with solution-processed organic halides to form halide perovskites, has emerged as a scalable and industry-compatible route for textured tandem photovoltaics. However, this process is often hindered by reaction-limited phase formation, particularly when compact, non-porous, and highly crystalline inorganic layers formed by thermal evaporation restrict subsequent conversion, resulting in incomplete reaction and pronounced depth-dependent heterogeneity. In this study, we introduce a strategy to regulate the inorganic precursor layer by incorporating localized heterogeneous nucleation sites. Sparsely distributed hydrophilic metal oxide species serve as effective nucleation centers during vapor deposition, enabling effective control over film morphology and crystal orientation from the early stages of growth. This tailored inorganic framework facilitates the subsequent incorporation of organic halides, alleviating reaction limitations and suppressing residual unreacted precursors. Consequently, the perovskite films exhibit improved stoichiometric uniformity and enhanced optoelectronic quality, enabling wide-bandgap perovskite solar cells with markedly improved performance and operational stability. This work provides important mechanistic insight into crystal growth engineering of vapor-deposited perovskite thin films.

nucleation↗