Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “selected inversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Calculation of atmospheric loss from microwave radiometric noise temperature measurements

Microwave propagation loss in the atmosphere can be inferred from microwave radiometric noise temperature measurements. The relevant equations are given and a derivation and calculation is made assuming various physical models. Comparison is made with the commonly used lumped element atmospheric model (isothermal and uniform loss) and the model with linear temperature and exponential loss distributions. The results are useful for estimating the integral inversion differences due to the model selection. This indicates that the commonly used lumped element atmospheric model is a very good approximation with judicious choice of the effective physical temperature. For the worst case comparison, the lumped element model agrees with the variable parameter model within 0.2 dB up to a propagation loss of 3 dB.

Stelzried, C.↗

Two-and-a-half-dimensional magnetohydrodynamic turbulence

The homogeneous turbulence for which fluctuating magnetic fields and velocity fields are independent of one spatial coordinate but still possess all three components are studied to form a generalized two-and-half dimensional geometry. The integral of the z-vector potential and the magnetic helicity are shown to be ideal invariants, and the basic dynamical variables and the equations of uniform-density incompressible magnetohydrodynamics are defined. The possibility of simultaneous inverse cascades is considered, and Kolmogoroff dimensional analysis is employed to infer omnidirectional inverse cascade spectra. Implications of a selective decay hypothesis, where a tendency exists in the initial value problem for the ideal invariants directly cascaded to higher wavenumbers to be selectively dissipated, and the possibility of a dynamo action in the considered geometry, are examined.

Montgomery, D.↗

Aerosol studies in mid-latitude coastal environments in Australia

The results of the evaluation of several inversion procedures that were used to select one which provides the most accurate atmospheric extinction profiles for small aerosol extinction coefficients (that often predominate in the maritime airmass) are presented. Height profiles of atmospheric extinction calculated by a two component atmospheric solution to the LIDAR equation will be compared with corresponding in-situ extinction profiles based on the size distribution profiles obtained in Western Australia. Values of the aerosol backscatter to extinction ratio obtained from multi-angle LIDAR measurements will be used in this solution.

Young, S. A.↗

Minimization search method for data inversion

Technique has been developed for determining values of selected subsets of independent variables in mathematical formulations. Required computation time increases with first power of the number of variables. This is in contrast with classical minimization methods for which computational time increases with third power of the number of variables.

Fymat, A. L.↗

A refined methodology for stress inversions of earthquake focal mechanisms: Refined Stress Inversion Methodology

We develop an improved methodology for reliable high-resolution inversions of focal mechanisms to background stress field orientation and stress ratio R in two or three dimensions. The earthquake catalog is declustered to remove events likely affected strongly by local stress interactions rather than reflecting the large-scale background stress field. The declustered data are discretized with the k-means algorithm into groups containing a number of focal mechanisms between a minimum number N min and 2N min . Synthetic tests indicate that N min ≈ 30 provides stable inversion results under different stress regimes and noise conditions when R ≈ 0.5, while N min ≈ 45 is needed for R near 0 or 1. Additional synthetic tests compare the performance of selecting the fault plane of each focal mechanism using (a) the plane with lowest misfit angle between the slip vector from the focal mechanism and shear traction from the stress tensor and (b) the plane with highest instability coefficient representing proximity to the optimally oriented fault for given stress field and friction coefficient. The instability criterion is found to provide more accurate inversion results under all tested stress regimes, stress ratios, and noise conditions. The refined inversion methodology combines selecting fault planes using the instability criterion iteratively with a damped simultaneous inversion of different focal mechanism groups. Results characterizing neighborhoods of discretized domains merged during the damped inversion provide high-resolution information independent of the discretization. Some aspects of the methodology are illustrated with focal mechanism data from the San Jacinto Fault Zone in Southern California.

58 GEOSCIENCES↗

Detection and Characterization of Underground Facilities by Stochastic Inversion and Modeling of Data from the New Generation of Synthetic Aperture Satellites (Final Report)

Many clandestine development and production activities can be conducted underground to evade surveillance. The purpose of the study reported here was to develop a technique to detect underground facilities by broad-area search and then to characterize the facilities by inversion of the collected data. This would enable constraints to be placed on the types of activities that would be feasible at each underground site, providing a basis the design of targeted surveillance and analysis for more complete characterization. Excavation of underground cavities causes deformation in the host material and overburden that produces displacements at the ground surface. Such displacements are often measurable by a variety of surveying or geodetic techniques. One measurement technique, Interferometric Synthetic Aperture Radar (InSAR), uses data from satellite-borne (or airborne) synthetic aperture radars (SARs) and so is ideal for detecting and measuring surface displacements in denied access regions. Depending on the radar frequency and the acquisition mode and the surface conditions, displacement maps derived from SAR interferograms can provide millimeter- to centimeter-level measurement accuracy on regional and local scales at spatial resolution of {approx}1-10 m. Relatively low-resolution ({approx}20 m, say) maps covering large regions can be used for broad-area detection, while finer resolutions ({approx}1 m) can be used to image details of displacement fields over targeted small areas. Surface displacements are generally expected to be largest during or a relatively short time after active excavation, but, depending on the material properties, measurable displacement may continue at a decreasing rate for a considerable time after completion. For a given excavated volume in a given geological setting, the amplitude of the surface displacements decreases as the depth of excavation increases, while the area of the discernable displacement pattern increases. Therefore, the ability to detect evidence for an underground facility using InSAR depends on the displacement sensitivity and spatial resolution of the interferogram, as well as on the size and depth of the facility and the time since its completion. The methodology development described in this report focuses on the exploitation of synthetic aperture radar data that are available commercially from a number of satellite missions. Development of the method involves three components: (1) Evaluation of the capability of InSAR to detect and characterize underground facilities ; (2) inversion of InSAR data to infer the location, depth, shape and volume of a subsurface facility; and (3) evaluation and selection of suitable geomechanical forward models to use in the inversion. We adapted LLNL's general-purpose Bayesian Markov Chain-Monte Carlo procedure, the 'Stochastic Engine' (SE), to carry out inversions to characterize subsurface void geometries. The SE performs forward simulations for a large number of trial source models to identify the set of models that are consistent with the observations and prior constraints. The inverse solution produced by this kind of stochastic method is a posterior probability density function (pdf) over alternative models, which forms an appropriate input to risk-based decision analyses to evaluate subsequent response strategies. One major advantage of a stochastic inversion approach is its ability to deal with complex, non-linear forward models employing empirical, analytical or numerical methods. However, while a geomechanical model must incorporate adequate physics to enable sufficiently accurate prediction of surface displacements, it must also be computationally fast enough to render the large number of forward realizations needed in stochastic inversion feasible. This latter requirement prompted us first to investigate computationally efficient empirical relations and closed-form analytical solutions. However, our evaluation revealed severe limitations in the ability of existing empirical and analytical forms to predict deformations from underground cavities with an accuracy consistent with the potential resolution and precision of InSAR data. We followed two approaches to overcoming these limitations. The first was to develop a new analytical solution for a 3D cavity excavated in an elastic half-space. The second was to adapt a fast parallelized finite element method to the SE and evaluate the feasibility of using in the stochastic inversion. To date we have demonstrated the ability of InSAR to detect underground facilities and measure the associated surface displacements by mapping surface deformations that track the excavation of the Los Angeles Metro system. The Stochastic Engine implementation has been completed and undergone functional testing.

58 GEOSCIENCES↗

Moessbauer medium with a hidden nuclear population inversion and negative absorption of gamma quanta

We consider physical foundations of an eventual experiment aimed at observing stimulated gamma-photon emission of long-lived Moessbauer isomers through selective frequency modulation of gamma-resonances establishing hidden population inversion without exceeding the number of excited nuclei over unexcited ones and without additional pumping. The examples of suitable nuclei and numerical estimates of the parameters are presented. (active media)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Robust unfolding of MeV x-ray spectra from filter stack spectrometer data

Here, we present an inversion method capable of robustly unfolding MeV x-ray spectra from filter stack spectrometer (FSS) data without requiring an a priori specification of a spectral shape or arbitrary termination of the algorithm. Our inversion method is based upon the perturbative minimization (PM) algorithm, which has previously been shown to be capable of unfolding x-ray transmission data, albeit for a limited regime in which the x-ray mass attenuation coefficient of the filter material increases monotonically with x-ray energy. Our inversion method improves upon the PM algorithm through regular smoothing of the candidate spectrum and by adding stochasticity to the search. With these additions, the inversion method does not require a physics model for an initial guess, fitting, or user-selected termination of the search. Instead, the only assumption made by the inversion method is that the x-ray spectrum should be near a smooth curve. Testing with synthetic data shows that the inversion method can successfully recover the primary large-scale features of MeV x-ray spectra, including the number of x-rays in energy bins of several-MeV widths to within 10%. Fine-scale features, however, are more difficult to recover accurately. Examples of unfolding experimental FSS data obtained at the Texas Petawatt Laser Facility and the OMEGA EP laser facility are also presented.

47 OTHER INSTRUMENTATION↗

Natural fibers as promising core materials of vacuum insulation panels

To reduce energy consumption in buildings, this paper investigates the feasibility of using natural fibers as cost-effective, environmentally sustainable core materials for vacuum insulation panels (VIPs). First, a comprehensive experimental study was conducted for 10 potential natural fiber candidates. The thermal conductivities of the 10 natural fiber mats at various vacuum pressures were measured; their compression and morphology properties were quantified. In addition, an analytical model was used to explore the major factors that influence the thermal conductivity of natural fibers as a function of internal air pressure. Results show that recycled cotton, kapok, and bamboo fibers are ideal candidates for VIP core materials; at <0.05 Pa, their thermal conductivities varied between 2 and 4 mW/(m∙K). Furthermore, for some fibers, thermal conductivity was inversely proportional to fiber density. For the selection of fiber materials for VIP cores, the ideal fiber candidate has a small fiber diameter and a low fiber mat density. Based on thermal measurements, even though the internal air pressure of 5 Pa was enough to attain the minimum thermal conductivity, obtaining internal air pressure below 5 Pa is recommended for prolonged service life, considering small leaks of VIP package barrier films and potential off-gassing from fibers. The simulation results predicting the effective thermal conductivities matched the experimental results well. These findings indicate that natural fiber–based VIPs have the potential to be a sustainable, inexpensive alternative to the current technologies in building insulation materials.

36 MATERIALS SCIENCE↗

Modification of Gaussian Elimination to the Complex Seismic Data

A method for solution of large and sparse systems with complex seismic observations has been developed by revising of the classical Gaussian elimination. The observation matrix is divided into a set of smaller cells that can be determined based on clusters of a seismic activity. Reliable inversion solutions with minimum error rating are selected within each cell, then solutions that are non-stable with respect to the same unknown are rejected After the final sifting the found unknowns are eliminated from the initial system with subsequent decreasing of its size. A numerical example is provided to demonstrate how the method can be applied to a real data set (a case study of the Nagano fault area, Central Japan). Results of processing of a huge volume of data and their importance for the Earthquake Early Warning (EEW) system are briefly discussed.

58 GEOSCIENCES↗

Machine learning-driven design and self-sensing capabilities of automotive bumper lattices for adaptive impact response

We present a novel approach to design an automotive bumper energy absorber using carbon fiber reinforced polymer composites, optimized to meet conflicting performance requirements for two distinct impact scenarios. The design must satisfy both a low-speed (2.5 mph) pendulum intrusion test, simulating vehicle-to-vehicle collisions, and a high-speed (25 mph) leg flexion test, replicating pedestrian impacts. These tests demand opposing deformation characteristics: high flexibility (deformation < 85 mm) for the former and high stiffness (deformation < 22 mm) for the latter. To address these contradictory requirements, we developed a machine learning (ML) framework for inverse optimization of lattice designs and material selection. Unlike traditional iterative design processes, our ML model directly outputs optimal design parameters and material choices based on target performance inputs. The energy absorber was fabricated using advanced additive manufacturing techniques, including extrusion deposition and digital light processing. The integration of carbon fibers provides multifunctionality to the bumper structure, enabling self-sensing capabilities through changes in electrical resistivity under compression. This electrical response demonstrates high repeatability under multiple cycles at 2% compression and exhibits distinct signatures during crack formation under high deformation. This research offers adaptive performance through innovative design methodologies and smart material integration. The approach has potential applications in various fields requiring adaptive energy absorption and real-time structural health monitoring.

Chawla, Komal [ORNL] (ORCID:0000000190327565)↗

Modeling Personalized Email Prioritization: Classification-based and Regression-based Approaches

Email overload, even after spam filtering, presents a serious productivity challenge for busy professionals and executives. One solution is automated prioritization of incoming emails to ensure the most important are read and processed quickly, while others are processed later as/if time permits in declining priority levels. This paper presents a study of machine learning approaches to email prioritization into discrete levels, comparing ordinal regression versus classier cascades. Given the ordinal nature of discrete email priority levels, SVM ordinal regression would be expected to perform well, but surprisingly a cascade of SVM classifiers significantly outperforms ordinal regression for email prioritization. In contrast, SVM regression performs well -- better than classifiers -- on selected UCI data sets. This unexpected performance inversion is analyzed and results are presented, providing core functionality for email prioritization systems.

97 MATHEMATICS AND COMPUTING↗

Time-Resolved Spectroscopy of Insulator-Metal Transitions: Exploring Low-Energy Dynamics in Strongly Correlated Systems. Final Report

Transition metal oxides (TMOs) have attracted much attention in recent years. The strong coupling between charge, spin, and orbital degrees of freedom creates novel functional properties. The research at the interplay between ferromagnetism, ferroelectricity and conductivity provides a promising way to the development of future spintronic devices. The interface characterization of multifunctional oxide heterostructures is crucial to understand deeply the magnetic response, spin injection and spin transport. In year one, we characterized optically the magnetic property with the method of magnetization-induced second-harmonic generation (MSHG), which is a sensitive technique to selectively probe the interface where the spatial inversion symmetry is broken. The interface of n-type BaTiO 3 (BTO)/La 0.67 Sr 0.33 MnO 3 (LSMO) forms a Schottky barrier and displays a good diode effect. By applying an external electric field across the sample, we observe the magnetoelectric (ME) coupling effect to modulate the interface magnetization. The voltage dependent magnetic contrast sharply vanishes at positive voltage (applied to LSMO contact) and reveals a ferromagnetic (FM)-to- antiferromagnetic (AFM) transition occurring at the interface, while the magneto-optic Kerr effect (MOKE) indicates that the bulk property is not affected. The strain mediated mechanism and ferroelectric (FE) polarization induced charge medicated mechanism are both discussed, but they do not play an important role in the observed magnetization transition. A new mechanism is proposed - the injected minority spins through strong Hund's interaction with the local magnetic moments at positive voltage weaken the double-exchange interaction of nearby Mn e g electrons, thereby reducing the ferromagnetic (FM) ordering. The dominant superexchange interaction of localized t 2g electrons finally leads to the AFM configuration. By reducing the electron carrier concentration of BTO, a positive voltage shift of the transition is observed. The oxygen richer sample with lower carrier concentration requires a higher voltage to increase the hole doping level of LSMO to induce the interfacial AFM phase. By inserting a thin (1nm) La 0.5 Ca 0.5 MnO 3 layer between BTO and LSMO, the interface magnetic response from LSMO is enhanced. In year two, a non-multiferroic heterostructure SrTiO 3 (STO)/ La 0.5 Ca 0.5 MnO 3 (LCMO)/La 0.67 Sr 0.33 MnO 3 (LSMO) was studied. In this system, the interface FM-AFM transition is observed at negative voltage. The STO layer may act as a hole-donating layer, which induces the hole transfer to LSMO making it overdoped, while the LCMO interlayer at the 0.5 hole doping level displays complicated CE type AFM phase. Thus the AFM phase is dominant at the interface and electron accumulation is required to induce the FM phase by applying a negative voltage. For oxygen rich sample, the magnetic MSHG loop reappears at high positive voltage (around +2.5 V). At high doping level (x > 0.5), LSMO exhibits A-type AFM order, consisting of AFM superexchange coupling between adjacent layers and intralayer FM double-exchange coupling. The less tensile strain of STO and LSMO due to a smaller lattice mismatch as compared to BTO would result in a weaker interlayer coupling . Thus, interfacial A-type AFM order can occur in STO/LCMO/LSMO heterostructure at high hole doping concentration. The study of ME coupling of multifunctional oxide heterostructures is definitely important to the development and performance of future spintronic devices. The results presented here regarding the interfacial magnetic transition controlled by an external electric field offer some new perspective to study the spin transport of magnetic tunnel junctions.

36 MATERIALS SCIENCE↗

CLUSTERING OF STAR-FORMING GALAXIES DETECTED IN MID-INFRARED WITH THE SPITZER WIDE-AREA SURVEY

We discuss the clustering properties of galaxies with signs of ongoing star formation detected by the Spitzer Space Telescope at the 24 {mu}m band in the SWIRE Lockman Hole field. The sample of mid-IR-selected galaxies includes {approx}20,000 objects detected above a flux threshold of S{sub 24{mu}m} = 310 {mu}Jy. We adopt optical/near-IR color selection criteria to split the sample into the lower-redshift and higher-redshift galaxy populations. We measure the angular correlation function on scales of {theta} = 0.{sup 0}01-3.{sup 0}5 , from which, using the Limber inversion along with the redshift distribution established for similarly selected source populations in the GOODS fields (Rodighiero et al.), we obtain comoving correlation lengths of r{sub 0} = 4.98 {+-} 0.28 h{sup -1} Mpc and r{sub 0} = 8.04 {+-} 0.69 h{sup -1} Mpc for the low-z (z{sub mean} = 0.7) and high-z (z{sub mean} = 1.7) subsamples, respectively. Comparing these measurements with the correlation functions of dark matter (DM) halos identified in the Bolshoi cosmological simulation, we find that the high-redshift objects reside in progressively more massive halos reaching M{sub tot} {approx}> 3 Multiplication-Sign 10{sup 12} h{sup -1} M{sub Sun }, compared to M{sub tot} {approx}> 7 Multiplication-Sign 10{sup 11} h{sup -1} M{sub Sun} for the low-redshift population. Approximate estimates of the IR luminosities based on the catalogs of 24 {mu}m sources in the GOODS fields show that our high-z subsample represents a population of 'distant ULIRGs' with L{sub IR} > 10{sup 12} L{sub Sun }, while the low-z subsample mainly consists of 'LIRGs', L{sub IR} {approx} 10{sup 11} L{sub Sun }. The comparison of number density of the 24 {mu}m selected galaxies and of DM halos with derived minimum mass M{sub tot} shows that only 20% of such halos may host star-forming galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗

Resin selection criteria for tough composite structures

Resin selection criteria are derived using a structured methodology consisting of an upward integrated mechanistic theory and its inverse (top-down structured theory). These criteria are expressed in a 'criteria selection space' which can be used to identify resin bulk properties for improved composite 'toughness'. The resin selection criteria correlate with a variety of experimental data including laminate strength, elevated temperature effects and impact resistance.

Chamis, C. C.↗

Resin selection criteria for tough composite structures

Resin selection criteria are derived using a structured methodology consisting of an upward integrated mechanistic theory and its inverse (top-down structured theory). These criteria are expressed in a "criteria selection space" which are used to identify resin bulk properties for improved composite "toughness". The resin selection criteria correlate with a variety of experimental data including laminate strength, elevated temperature effects and impact resistance.

Chamis, C. C.↗