Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “segregation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Triple-halide wide–band gap perovskites with suppressed phase segregation for efficient tandems

Wide–band gap metal halide perovskites are promising semiconductors to pair with silicon in tandem solar cells to pursue the goal of achieving power conversion efficiency (PCE) greater than 30% at low cost. However, wide–band gap perovskite solar cells have been fundamentally limited by photoinduced phase segregation and low open-circuit voltage. Here, we report efficient 1.67–electron volt wide–band gap perovskite top cells using triple-halide alloys (chlorine, bromine, iodine) to tailor the band gap and stabilize the semiconductor under illumination. We show a factor of 2 increase in photocarrier lifetime and charge-carrier mobility that resulted from enhancing the solubility of chlorine by replacing some of the iodine with bromine to shrink the lattice parameter. We observed a suppression of light-induced phase segregation in films even at 100-sun illumination intensity and less than 4% degradation in semitransparent top cells after 1000 hours of maximum power point (MPP) operation at 60°C. By integrating these top cells with silicon bottom cells, we achieved a PCE of 27% in two-terminal monolithic tandems with an area of 1 square centimeter.

14 SOLAR ENERGY↗
DOE OSTI2025

Halide segregation to boost all-solid-state lithium-chalcogen batteries

Mixing electroactive materials, solid-state electrolytes, and conductive carbon to fabricate composite electrodes is the most practiced but least understood process in all-solid-state batteries, which strongly dictates interfacial stability and charge transport. Here, we report on universal halide segregation at interfaces across various halogen-containing solid-state electrolytes and a family of high-energy chalcogen cathodes enabled by mechanochemical reaction during ultrahigh-speed mixing. Bulk and interface characterizations by multimodal synchrotron x-ray probes and cryo–transmission electron microscopy show that the in situ segregated lithium halide interfacial layers substantially boost effective ion transport and suppress the volume change of bulk chalcogen cathodes. Various all-solid-state lithium-chalcogen cells demonstrate utilization close to 100% and extraordinary cycling stability at commercial-level areal capacities.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Role of Oxygen on Chemical Segregation in Uncapped Ge 2 Sb 2 Te 5 Thin Films on Silicon Nitride

Germanium antimony telluride has been the most used and studied phase-change material for electronic memory due to its suitable crystallization temperature, amorphous to crystalline resistance contrast, and stability of the amorphous phase. In this paper, the segregation of Ge in a Ge 2 Sb 2 Te 5 film of 30 nm thickness during heating inside the transmission electron microscope was observed and characterized. Furthermore, Ge 2 Sb 2 Te 5 film was deposited using sputtering on a Protochips Fusion holder and left uncapped in atmosphere for about four months. Oxygen incorporated within the film played a significant role in the chemical segregation observed which resulted in amorphous Ge-O island boundaries and Sb and Te rich crystalline domains. Such composition changes can occur when the phase-change material interfaces insulating oxide layers in an integrated device and can significantly impact its electrical and thermal properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Optimizing thermal stability and mechanical behavior in segregation-engineered nanocrystalline Al–Ni–Ce alloys: A combinatorial study

The deliberate use of solute enrichment at grain boundaries, otherwise known as segregation engineering, is a promising approach to tailor the properties of interface-dominated materials such as nanocrystalline alloys. Here, the ensuing chemical and structural evolution at grain boundaries can give rise to thermal stability and excellent mechanical properties, but the interplay between enrichment, phase decomposition, grain growth, and mechanical behavior exists in a vast composition and processing space. In this study, a combinatorial synthesis and rapid characterization approach was applied to segregation-engineered nanocrystalline Al–Ni–Ce alloys to assess the evolution of microstructure and resulting mechanical behavior as functions of alloying content and annealing conditions. In addition to the identification of alloys and processing conditions that give rise to exceptional thermal stability, strength retention, and homogeneous plastic flow, we construct combined thermal stability and deformation mechanism maps that demarcate several important regimes of behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Bulk segregant and QTL analysis of maltose metabolism in Saccharomyces eubayanus

This study investigates natural variation in maltose utilization among Saccharomyces eubayanus strains isolated from different tree hosts. An F2 population was generated from a cross between strain QC18 (Quercus-associated) and strain CL467.1 (Nothofagus-associated). Bulk segregant analysis (BSA) was performed on the F2 offspring, and QTL mapping was conducted by whole-genome sequencing of two pools of 30 segregants each, representing the lowest and highest growth in high maltose concentrations. For QTL analysis, the parental strains QC18 and CL467.1 were also sequenced.

evolutionary plasticity↗
DOE OSTI2022

Novel Segregated Solid Propulsion System with Separately Stored Fuel and Oxidizer

Abstract The development and experimentation of a solid propulsion concept consisting of separate hydrogen‐rich solid propellant and solid oxidizer grains is presented. This system consists of an extremely fuel‐rich solid propellant, which, once ignited, undergoes a self‐sustaining decomposition to release fuel‐rich product gases, which are particularly rich in hydrogen gas. These relatively high‐temperature gases subsequently react with a solid oxidizer grain stored downstream. Progress in high‐nitrogen materials has allowed for the synthesis of fuel‐rich compounds that can store significant amounts of hydrogen, with little or no bound oxygen. With these new developments in propellant chemistry, a unique segregated propulsion system has been developed, creating an all‐solid propulsion system that combusts analogously to a reverse hybrid rocket system. Because of the physical separation of fuel and oxidizer, a higher level of safety is achieved which concurrently allows for the utilization of higher energy ingredients without the penalty of higher sensitivity. Theoretical performance calculations and experimental data have shown the potential for this system to compete with existing composite rocket propellants while having significant benefits in terms of safety, toxicity, and mission space. This paper presents a detailed overview of the conception, development, and testing of this propulsion system.

42 ENGINEERING↗
DOE OSTI2021

Elemental segregation to lattice defects in the CrMnFeCoNi high-entropy alloy during high temperature exposures

The influence of small plastic pre-strains on the elevated-temperature stability and microstructure of the equiatomic CrMnFeCoNi FCC solid solution is investigated. Particular attention is given to whether any of the alloy elements segregate to individual dislocations. To that end, CrMnFeCoNi samples were first deformed in tension at room temperature to plastic strains of 0.2 and 2.3%, and subsequently annealed at 973 K for 800 hours. The pre-strains activated planar slip of 1/2<110>-type dislocations on {111}-type glide planes. Interactions of this planar slip with special Σ3 grain boundaries formed a large number of dislocation segments with a <110>-type crystallographic orientation suitable for a credible end-on analysis of dislocation cores in HR-STEM. The cores of the 1/2<110> dislocations pushed up against the investigated grain boundaries were found to be close to the compact configuration. Within the sensitivity of the Super-X EDS mapping, no concentration gradient was detected near dislocations that would indicate enrichment at dislocation cores of any of the elemental constituents of the alloy after the pre-deformation and annealing. However, a Cr-rich tetragonal sigma phase nucleated and grew at grain boundary triple junctions during this anneal, processes that were not accelerated by the enhanced dislocation density present after pre-strain. A clear chromium gradient was observed in the Cr-depleted zones near grain boundaries suggesting that Cr transport occurred by relatively slow diffusion from the bulk to the grain boundaries and then by relatively fast diffusion along the grain boundaries to the precipitates. Accompanying the Cr depletion near grain boundaries is a simultaneous Ni and Mn enrichment, which promotes formation of the L1 0 NiMn phase that is observed on the grain boundaries after prolonged annealing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Analysis of phase stability and chemical segregation in the Mo-V alloys using a generalized embedded atom method potential

A new interatomic potential for the Mo-V system is introduced to facilitate the study of phase stability and mechanical properties at lower temperatures. This potential is based on a generalization of the embedded atom method and includes contributions from embedding energy, explicit two- and three-body interactions and nonlocal many-body interaction terms. The parameters of the potential are optimized by using data from ab initio density functional theory (DFT) calculations. The potential is rigorously validated across a range of physical properties, such as elastic constants, equation of states, phonon dispersion curves, point defect properties and melting temperatures for different compositions. Even though our potential is trained on a small dataset, its accuracy is comparable to available machine learning potentials for Mo and V. Furthermore, our results show that an ordered B2 phase is stable at low temperatures in alloys containing 50% V, but the solid solution phase is stable above 800 K. However, such long-range ordering is not observed in V-rich or Mo-rich alloys. In addition, our results show that V segregates to dislocation cores and grain boundaries.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding effects of chemical complexity on helium bubble formation in Ni-based concentrated solid solution alloys based on elemental segregation measurements

Here, helium bubble formation and swelling were systematically studied in Ni-based concentrated solid solution alloys containing different numbers and types of elements. Our microscopy analysis showed that although increasing the alloy chemical complexity helps suppress bubble formation in general, there is no monotonic relationship between the bubble growth rate and the number of alloying elements. Certain elements (e.g., Fe and Pd) are more effective in suppressing bubble growth than others (e.g., Cr and Mn). Atom probe tomography was applied to accurately measure elemental segregation around bubbles, revealing unique effects of certain alloying elements on vacancy migration towards bubbles. More specifically, the high vacancy mobility via Cr sites leads to a large vacancy flux and an increased bubble size, while the high degree of atomic size mismatch introduced by Pd helps deflect vacancy flow away from bubbles and decrease the amount of swelling. The effects identified in this study provide new strategies to design concentrated solid solutions with superior resistance to swelling.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase Segregation and Sequential Expulsion of Iodide and Bromide in Photoirradiated Ruddlesden–Popper 2D Perovskite Films

Two-dimensional (2D) Ruddlesden–Popper mixed-halide perovskite films, BA 2 PbBr 2 I 2 , undergo phase segregation when excited with visible light to generate bromide- and iodide-rich regions, as marked by absorption and emission changes. Upon stopping illumination, the process reverses, allowing original film compositions to be restored. However, if films are in contact with dichloromethane, light irradiation causes the sequential expulsion of iodide and bromide and introduces irreversible changes to the 2D films. The sequential disappearance of I– and Br– from pristine films (BA 2 Pb 2 Br 4 and BA 2 Pb 2 I 4 ) under photoirradiation, as observed from variances in expulsion rates, reflects differences in halide ion mobilities in these films. The photoinstability of 2D films raises questions about their use in stabilizing bulk, three-dimensional (3D) perovskite solar cells through 3D/2D interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Designing for cooperative grain boundary segregation in multicomponent alloys

Tailoring the nanoscale distribution of chemical species at grain boundaries is a powerful method to dramatically influence the properties of polycrystalline materials. However, classical approaches to the problem have tacitly assumed that only competition is possible between solute species. In this paper, we show that solute elements can cooperate in the way they segregate to grain boundaries: In properly targeted alloys, the different chemical species cooperate to each fill complementary grain boundary sites disfavored by the other. By developing a theoretical “spectral” approach to this problem based on quantum-accurate grain boundary site distributions, we show how grain boundaries can be cooperatively alloyed, whether by depletion or enrichment. We provide machine-learned cosegregation information for over 700 ternary aluminum-based alloys and experimentally validate the concept in one ternary alloy where cosegregation is not expected by prior models but is expected based on the cooperative model.

grain boundaries↗
DOE OSTI2023

Effect of Production Bias on Radiation-Induced Segregation in Ni-Cr Alloys

We present an in-depth investigation into the Radiation-Induced Segregation (RIS) phenomenon in Ni-Cr alloys. All the pivotal factors affecting RIS such as surface’s absorption efficiency, grain size, production bias, dose rate, temperature, and sink density were systematically studied. Through comprehensive simulations, the individual and collective impacts of these factors were analyzed, enabling a refined understanding of RIS. A notable finding was the significant influence of production bias on point defects’ interactions with grain boundaries/surfaces, thereby playing a crucial role in RIS processes. Production bias alters the neutrality of these interactions, leading to a preferential absorption of one type of point defect by the boundary and consequent establishment of distinct surface-mediated patterns of point defects. These spatial patterns further result in non-monotonic spatial profiles of solute atoms near surfaces/grain boundaries, corroborated by experimental observations. In particular, a positive production bias, signifying a higher production rate of vacancies over interstitials, drives more Cr depletion at the grain boundary. Moreover, a temperature-dependent production bias must be considered to recover the experimentally reported dependence of RIS on temperature. The severity of radiation damage and RIS becomes more pronounced with increased production bias, dose rate, and grain size, while high temperatures or sink density suppress the RIS severity. Model predictions were validated against experimental data, showcasing robust qualitative and quantitative agreements. The findings pave the way for further exploration of these spatial dependencies in subsequent studies, aiming to augment the comprehension and predictability of RIS processes in alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase-field modeling of radiation-induced segregation for multicomponent alloys

Structural alloys under irradiation are known to undergo radiation-induced solute redistribution (RIS) at grain boundaries, leading to detrimental effects such as intergranular corrosion and stress-assisted cracking. To better understand the phenomenon, improved models of RIS applicable to concentrated, multicomponent alloys, and mesoscale microstructures are needed. In this talk, we present a novel grand-potential-based phase-field model to account for the complete set of multicomponent kinetic and thermodynamic couplings between atoms and point defects in the Onsager transport equations. We demonstrate multiscale modeling capability by deriving the Onsager coefficient matrix from atomistic-based Kinetic Monte Carlo simulations. Model predictions and validations of RIS and the effect of defect production, grain boundary sink strength and density are demonstrated for a model FCC FeCrNi system. We also demonstrate the novel capability to describe RIS in the presence of equilibrium segregation described using a density-based CALPHAD thermodynamic framework. This modeling approach overcomes certain limitations in conventional RIS models and provides a step closer towards multiscale modeling.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Spectroscopic determination of metal redox and segregation effects during CO and CO/NO oxidation over silica-supported Pd and PdCu catalysts

Here, we report the effects of alloying Cu into silica supported Pd nanoparticles on the catalytic activity, surface composition, and particle structure during CO oxidation Pd is highly active for CO oxidation but is inhibited by relevant competitive reagents (e.g. NO) at low temperatures (< 150 °C). By alloying Cu into Pd nanoparticles, NO inhibition is suppressed without any CO oxidation activity loss. Infrared spectroscopy illustrates the formation of surface nitrosyl (NO-Pd) is eliminated in the PdCu alloy catalyst, preventing CO oxidation inhibition by NO. X-ray absorption spectroscopy studies show that Pd in the monometallic catalyst forms a surface oxide after light-off. Conversely, in the PdCu catalyst, Pd remains metallic during reaction, independent of temperature, whereas the Cu oxidizes when the catalyst becomes active, after light-off. Furthermore, DRIFTS studies show that the Cu segregates to the surface as the catalyst becomes active for diesel oxidation, presumably becoming the O 2 adsorption site.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Indium segregation in Gd 5 (Si, Ge) 4 magnetocaloric materials

Chemical substitution is one of the most efficient tools to tune and optimize magnetic and magnetocaloric properties of the giant magnetocaloric materials. In particular, Indium substitutions could be useful both for tuning properties of these interesting intermetallic materials and to unveil their local-scale behavior across the magnetostructural transition via hyperfine techniques. Hence, in order to investigate the effect of Indium additions on the crystal structure, micro-structure, magnetic and magnetocaloric properties, a series of In-containing samples derived from the base Gd 5 Si 1.2 Ge 2.8 stoichiometry were prepared. Here, the major findings are that while In is insoluble in the 5:4 phase, it will instead promote the emergence of the impurity 5:3 phase and segregates into this phase. Hence, In leads to major crystallographic changes, which enhance atomic disorder and disrupt the Si to Ge ratio in the 5:4 phase. Subsequently, a higher 5:4 unit cell volume and a lower magnetic ordering temperature are found in the In-substituted samples. Finally, the magnetocaloric properties of the In-substituted samples reveal a detrimental effect on the maximum magnetic entropy change.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Nanoscale clustering and fission product segregation in irradiated annular U-10Zr fuel

Zirconium (Zr) is added to uranium (U) to improve the performance of metallic fuel for fast reactor applications. This study employs transmission electron microscopy (TEM) and atom probe tomography (APT) to investigate nanoscale clustering of U and Zr, as well as segregation of fission products (FPs), in annular U-10Zr (in weight) metallic fuel irradiated at the Advanced Test Reactor (ATR). The results reveal variations in the shape, size, and chemical composition of clusters at different radial locations within the irradiated fuel cross-section. Zr-rich clusters exhibit higher concentration of FPs compared to U-rich clusters, potentially due to the co-precipitation of Zr and FPs in the fuel matrix during cooling at the end-of-life. In conclusion, this work complements the study of fuel constituents and fission product distribution across multiple length scales in irradiated U-10Zr metallic fuel.

Atom probe tomography↗
DOE OSTI2023

Additive manufacturing of a metastable high entropy alloy: Metastability engineered microstructural control via process variable driven elemental segregation

Compositional paradigm shift in high entropy alloys (HEAs) provided new opportunities for microstructural engineering, whereas process control during laser powder bed fusion (LPBF) additive manufacturing (AM) enable fine microstructure tailoring. Metastability engineering in transformation induced plasticity (TRIP) HEAs by addition of minor alloying elements is an attractive strategy for fine microstructural tuning. This study explored in detail the microstructural evolution during LPBF AM of a metastable Fe 40 Mn 20 Co 20 Cr 15 Si 5 (at.%) dual phase HEA (CS-HEA). LPBF processing window for CS-HEA was established based on quantitative analysis and experiments. Based on melt pool overlap lack of fusion pores were observed at lower energy densities (J) of $\textit{J}$ ≤ 31.25 J/mm 3 and key-hole formation by melt pool destabilization in case of $\textit{J}$ ≥ 75 J/mm 3 . The microstructure of CS-HEA consists of metastable FCC-γ and HCP-ε phases; LPBF process parameters governed the final phase fraction in the alloy which has been correlated to metastability alteration of the high temperature γ phase. Final microstructural engineering was devised by LPBF process control which enabled cooling rate manipulation to guide Mn and Si segregation at the cell boundaries, thereby controlling the matrix metastability and final phase fraction. Additionally, high resolution transmission electron microscopy (TEM) revealed disparity in stacking fault morphology in CS-HEA with LPBF process variable alterations associated with local variations in chemical composition and stacking fault energy. Further, the phase evolution with process parameters also affected the nanomechanical behavior of the alloy.

36 MATERIALS SCIENCE↗