Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polycrystalline”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

GaN/InGaN Blue Light-Emitting Diodes on Polycrystalline Molybdenum Metal Foils by Ion Beam-Assisted Deposition

Light-emitting diode (LED) arrays fabricated on a polycrystalline metal substrate are demonstrated using a novel technique that enables the growth of epitaxial metal-organic chemical vapor deposition (MOCVD) GaN layers on non-single-crystal substrates. Epitaxial GaN is deposited directly on metal foil using an intermediate ion beam-assisted deposition (IBAD) aligned layer. For a single 170 μm-diameter LED on the metal foil, electroluminescence (EL) spectrum shows a peak wavelength of ≈452 nm and a full width at half maximum (FWHM) of ≈24 nm. The current–voltage (I –V ) characteristics show a turn-on voltage of 3.7 V, a series resistance of 10 Ω. LEDs on metal show a relative external quantum efficiency (EQE) that is roughly 3× lower than that of similar LEDs fabricated on a sapphire substrate. Finally, InGaN LEDs on large-area non-single-crystal substrates such as metal foils enable large-area manufacturing, reducing production cost, and opening the door for new applications in lighting and displays.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Thermomechanical Cleave of Polycrystalline CdTe Solar Cells and its Applications: A Review

One of the primary research challenges for cadmium telluride (CdTe) solar cells is addressing its open‐circuit voltage ( V OC ) deficit. While theoretical studies and single crystal work show V OC > 1 V is possible, devices remain stubbornly low at ≈800–900 mV. As absorber opto‐electronic properties (e.g., hole density, carrier lifetime) are improved, device modeling suggests that interfaces become limiting. Because CdTe‐based devices are typically grown in the superstrate configuration, the back interface is relatively accessible for manipulation and study, while the front interface (i.e., the heterojunction region) is buried under microns of material and inaccessible. NREL has developed a novel technique to thermomechanically cleave polycrystalline CdTe device stacks directly at the front interface, enabling characterization and controlled manipulation of this important region. Herein, recent work, primarily from NREL, will be reviewed, including considerations for achieving successful delamination; key scientific discoveries about the front interface that have been enabled by this technique; and practical applications, such as flexible, low‐cost solar with high power‐to‐weight ratio.

14 SOLAR ENERGY↗
DOE OSTI2025

Measurement of Contact Resistivity In Symmetric Polycrystalline Si/SiO x /Monocrystalline Si Test Structures Using Variable Light Illumination

While different methods exist to determine the contact resistivity in semiconductor devices, these methods are limited to measurement of the majority carrier contacts. The measurement of p‐ or n‐type contacts on n‐ or p‐type crystalline silicon, respectively, is challenging due to the blocking diode formed by the p–n junction. In this article, we address this problem for tunneling oxide passivating contacts used in high‐efficiency Si solar cells. We propose a universal method to extract contact resistivity on symmetric test structures with polycrystalline silicon on SiO x (poly‐Si/SiO x ) passivating contacts under illumination, both for p–n and high–low‐junction passivated contacts. In this method, we demonstrate that the total contact resistance of each cell grid finger to the base wafer is governed by its effective contact area, defined by the transfer length extending from both sides of the finger. Therefore, the grid contact resistance of a poly‐Si contact depends on the ratio of the doped poly‐Si sheet resistance to the tunneling contact resistivity.

14 SOLAR ENERGY↗
DOE OSTI2026

Electron beam irradiation effects on bulk metals: a comparative study of polycrystalline versus single-crystalline structures

This study investigates the effects of electron beam (e-beam) irradiation on the mechanical and structural properties of eight bulk metallic samples, comprising both polycrystalline (PC) and single-crystalline (SC) forms of Ni, Cr, V, and Ti. These metals were evaluated as potential candidates for beam exit windows in high-power (MW-class) particle accelerators. The primary objective is to identify metals capable of withstanding the conditions of high-power/MW-class e-beam accelerators and serve effectively as exit windows. Selection criteria were based on each metal’s intrinsic properties, power dissipation capability, and irradiation-induced changes in mechanical behavior, including hardness, elastic modulus, and defect density. Comprehensive characterization was conducted using field-emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDS), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and nanoindentation, performed both before and after exposure to a ~¿66 kGy dose from a 10 MeV e-beam accelerator. Results revealed that e-beam irradiation induced hardening in PC Ni, whereas PC Ti, commonly used in beam exit windows, exhibited softening. The observed softening in PC Ti is attributed to grain coarsening, elongation, and the formation of twins and twin boundaries, in contrast to the smaller, compressed grains in the pristine (Pr) PC Ti samples, consistent with the Hall–Petch relationship. The stresses due to twinning are small and insignificant in influencing the overall hardening of the PC Ti irradiated sample when compared to the stresses due to the dislocation density. Conversely, SC Ti samples exhibited irradiation-induced hardening. The SC Ti irradiated samples developed additional irradiation-induced modifications in crystallographic texture of (100), (101), (110), (200), (112), (004), and (211) as evidenced from the XRD results, which could probably explain the hardening effect that is caused by irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A complete grain-level assessment of the stress-strain evolution and associated deformation response in polycrystalline alloys

Polycrystalline alloys are used pervasively across structural applications contingent upon extensive experimental testing. A statistically representative number of tests are required to expose the variability in the material's performance, as a result of non-uniform microstructures and associated micromechanical fields. In a more direct means of capturing this pertinent information, multi-modal experimental techniques are presented to measure and track the complete micromechanical state, evolving during loading, of each and every grain within the regions of interest. Specifically, a combination of high-energy X-ray diffraction microscopy and digital image correlation coupled with electron backscatter diffraction are conducted on a specimen for each of the alloys, Haynes 282 and Ti7Al. The results of the multi-modal analysis definitively demonstrate that the degree of heterogeneity increases with deformation level and is used to assess the number of grains necessary for a representative volume element description of the stress state for each of these materials. Moreover, higher resolution imaging is used for identification of the slip system activity and subsequently used to study slip transmission events. An accurate knowledge of the resolved shear stress in adjacent grains (grain interactions) is demonstrated to be a key descriptor of the slip transmission events.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Domain wall motion across microstructural features in polycrystalline ferroelectric films

This paper describes the effect of microstructural features such as grain boundaries and triple points on the pinning of domain wall motion in perovskite Pb(Zr 0.52 Ti 0.48 )O 3 (PZT) films on polycrystalline SrRuO 3 /SrTiO 3 substrates. Here, spatial variability in the collective domain wall dynamics was assessed using non-linearity mapping via Band Excitation Piezoresponse Force Microscopy (BE-PFM). Collocating the non-linearity maps with triple point locations (as visualized by EBSD) allowed for exploration of the effects that local microstructure (e.g., grain boundary) have on domain wall motion. It was found that the extrinsic behavior varied with both the misorientation angle and the proximity to the grain boundary. The width of influence of individual grain boundaries on the motion of domain walls was a function of the character of the grain boundary; random grain boundaries exhibit deeper minima in α d /d 33,initial and larger widths of influence (up to 905 nm) compared to coincident site lattice (CSL) boundaries (up to 572 nm). Additionally, triple points containing larger numbers of random boundaries exhibited non-Rayleigh behavior to greater distances, suggesting that the triple point provides either a deep potential minimum or a region where domain wall motion is unfavorable.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Active learning for the design of polycrystalline textures using conditional normalizing flows

Generative modeling has opened new avenues for solving previously intractable materials design problems. However, these new opportunities are accompanied by a drastic increase in the required amount of training data. This is in stark juxtaposition to the high expense and difficulty in curating such large materials datasets. In this work, we propose a novel framework for integrating generative models within an active learning loop. Further, this enables the training of generative models with datasets significantly smaller than what has previously been demonstrated, providing a direct route for their application in data constrained environments. The functionality of this framework is then demonstrated by addressing the challenge of designing polycrystalline textures associated with target anisotropic mechanical properties. The developed protocol exhibited a cost reduction between 14 to 18 times over a randomly sampled experimental design.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Large room-temperature elastocaloric effect in a bulk polycrystalline Ni-Ti-Cu-Co alloy with low isothermal stress hysteresis

Creation of high-performance advanced elastocaloric materials is essential for the execution of elastocaloric refrigeration that can be an environment-friendly and high-efficiency substitute for the widely used traditional vapor-compression cooling technology. Here we have developed a bulk polycrystalline Ni-Ti-Cu-Co shape memory alloy exhibiting large elastocaloric effect, low stress hysteresis and room temperature working temperature, all of which are of great importance to and urgently demanded for high-efficiency room-temperature elastocaloric refrigeration. This newly developed (Ni 42.5 Ti 50 Cu 7.5 ) 99 Co 1 alloy shows a large room-temperature elastocaloric effect with directly measured adiabatic temperature change up to -14.4 K during unloading. The stress hysteresis of the isothermal superelastic stress-strain curve is as low as 60 MPa when the maximum tensile strain is 2.7%. Owing to the large elastocaloric effect and low stress hysteresis, a very high coefficient of performance up to 19 is achieved on the material level. This newly developed (Ni 42.5 Ti 50 Cu 7.5 ) 99 Co 1 alloy is a robust candidate for efficient elastocaloric refrigeration. Advanced in-situ synchrotron high-energy X-ray diffraction technique was employed to reveal the phase transformation sequence and to accurately determine the crystal structure of different phases, based on which the lattice compatibility between the transforming phases was evaluated and the phase transformation strain was predicted, providing in-depth fundamental understanding of the martensitic transformation in this newly developed alloy. This work could be useful for designing high-performance elastocaloric materials for solid-state cooling applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A computational study of the effects of graphene additions on electrical properties of polycrystalline copper

The addition of graphene has recently shown promise as a route for the significant improvement of the bulk electrical properties of metallic materials. Here, we explore the effects these additions have on the net electrical conductivity of fabricated copper-graphene (Cu-Gr) nanocomposites as a function of grain structure and grain boundary properties. Synthetic 3D microstructures were generated to represent polycrystalline copper with different average grain diameters and twinned grain boundary fractions. Then, the Poisson equation of electrical transport was solved using a finite difference method in order to predict the net electrical conductivity of each microstructure. In this context, the potential effect of graphene on the conductivity of the composite was evaluated as a function of the number of affected grain boundaries. The results of these calculations indicate that 1.) as supported by literature, net electrical conductivity decreases with decreasing grain size, 2.) the presence of twinned grain boundaries results in smaller loss of conductivity than would otherwise be expected, and 3.) the presence of graphene on the grain boundaries can be expected to lead to improvements in net electrical conductivity. However, we also find that 4.) when the Cu grain structure becomes sufficiently refined, the addition of graphene could conceivably result in significant improvements in electrical conductivity over and above coarse-grained Cu. It is estimated from our calculations that, assuming microstructures with average grain sizes between 100 nm and 100 μm and graphene conductivity 1000 to 10,000 that of a typical Cu grain boundary, an improvement in electrical conductivity of approximately 17% over that of bulk Cu may be attainable. Therefore, by performing this study we suggest a possible route for the improvement of Cu electrical properties through the addition of graphene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Modeling brittle fracture due to anisotropic thermal expansion in polycrystalline materials

Here, this work investigated brittle fracture of polycrystalline materials due to thermal stresses arising from anisotropic thermal expansion. We used phase-field fracture simulations with the properties of alpha-uranium (α-U) and assumed a linear elastic mechanical response. Three-dimensional simulations were used to predict fracture for various conditions and crystallographic textures. We found that fracture was more pronounced during cooling than during heating because the anisotropy increased with temperature. We also found that the total crack surface area increased with increasing average misorientation, while the net shape change of the material decreased with increasing misorientation. Two-dimensional simulations in which one crystallographic coefficient of thermal expansion (CTE) was set to zero indicated that the expansion behavior in the crystallographic direction with the smallest CTE was the primary cause of fracture.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Effect of loading path on grain misorientation and geometrically necessary dislocation density in polycrystalline aluminum under reciprocating shear

Solid phase processing (SPP) is a promising alloy fabrication technique to produce fine and homogeneous grain structures for high-performance alloys. However, there is very limited modeling capability to understand and predict the grain refinement during SPP. In this work, the crystal plasticity theory was used to study elastic-plastic deformation in polycrystalline aluminums under large shear deformation. Two approaches, kernel averaged misorientation (KAM) and grain reference orientation deviation (GROD), were used to assess the grain misorientations. The geometrically necessary dislocation (GND) density was computed with the plastic strain rate. The deformation simulations were carried out under two loading conditions to investigate the effect of loading paths on the evolutions of grain misorientation and GND density. The results show that the regions with high misorientation and GND density first appear near grain boundaries. These regions then extend toward interior grains. The loading path affects dislocation system activation and dislocation recovery, hence dislocation evolution and misorientation. In conclusion, both two- and three-dimensional simulations showed that the spatial and temporal evolutions of GROD, KAM, and GND density in are closely correlated, which indicates they all can be used as criteria of grain refinement or recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

GrainNN: A neighbor-aware long short-term memory network for predicting microstructure evolution during polycrystalline grain formation

High fidelity simulations of grain formation in alloys are an indispensable tool for process-to-mechanical-properties characterization. Such simulations, however, can be computationally expensive as they require fine spatial and temporal discretizations. Their cost becomes an obstacle to parametric studies and ensemble runs and ultimately makes downstream tasks like optimal control and uncertainty quantification challenging. To enable such downstream tasks, we introduce GrainNN, an efficient and accurate reduced-order model for epitaxial grain growth in additive manufacturing conditions. GrainNN is a sequence-to-sequence long-short-term-memory (LSTM) deep neural network that evolves the dynamics of manually crafted features. Its innovations are (1) an attention mechanism with grain-microstructure-specific transformer architecture; and (2) an overlapping combination of several clones of the network to generalize to grain configurations that are different from those used for training. This design enables GrainNN to predict grain formation for unseen physical parameters, grain number, domain size and geometry. Furthermore, GrainNN not only reconstructs the quantities of interest but also can be pointwise accurate. In our numerical experiments, we use a polycrystalline phase field method to both generate the training data and assess GrainNN. For multiparametric, ensemble simulations with many grains, GrainNN can be orders of magnitude faster than phase field simulations, while delivering 5%–15% pointwise error. Additionally, this speedup includes the cost of the phase field simulations for generating training data.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Locking oxygen in lattice: A quantifiable comparison of gas generation in polycrystalline and single crystal Ni-rich cathodes

High-energy Ni-rich NMC (LiNi x Mn y Co 1-x-y O 2 , x ≥ 0.6) is a very promising cathode material in Li-ion batteries but the gas generation during cycling is a significant safety concern and becomes the major roadblock of the large-scale commercialization of Ni-rich NMC cathode materials. Micron-sized single crystal Ni-rich NMC has a potential to address the common issues that polycrystals have. However, it is unknown if gassing issue will be mitigated or even eliminated by using single crystals, not mentioning a quantifiable understanding of gas generation from single crystals and polycrystals. This work takes LiNi 0.76 Mn 0.14 Co 0.1 O 2 (NMC76) as a model material to study the mechanism of gas generation from single crystal and polycrystalline NMC by using both coin cells and pouch cells, which provides different conclusions on the generated gases, highlighting the importance of using relevant testing conditions for fundamental diagnostic study on battery materials. Further, the information from single crystal NMC also provides critical insights from material perspective to enhance the safety attributes of Ni-rich NMC cathodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Micro-cantilever beam experiments and modeling in porous polycrystalline UO 2

Understanding the impact of microstructure on the thermo-mechanical behavior of oxide nuclear fuels is vital to predicting their performance through multiscale models. Evaluating the mechanical properties at the sub-grain length scale is key to developing these multiscale models. In this work, 3D finite element (FE) models were constructed to simulate the micrometer-scale bending of micro-cantilever beams fabricated using porous polycrystalline uranium dioxide (UO 2 ) and tested at room temperature. Here, the results showed that the porosity and elastic anisotropy of individual grains can play a significant role in determining the effective mechanical properties of the material deduced from the tests. Specifically, the porosity had a non-negligible effect, given that the pore size was of the same order of magnitude as the dimensions of the micro-beams. Correlations between load-deflection data, pore location, and elastic properties (effective Young's modulus) were investigated using UO 2 micro-beam FE models, where pore clusters were included and placed at different locations along the length of the beam. Results indicated that the presence of pore clusters near the substrate, i.e., the clamp of the micro-cantilever beam, has the strongest effect on the load-deflection behavior, with the porosity leading to a reduction of stiffness that is the largest for any location of the pore clusters. Furthermore, it was also found that pore clusters located towards the middle of the span and close to the end of the beam have a comparatively small effect on the load-deflection behavior. Therefore, it is concluded that accurate estimates of Young's modulus can be obtained from micro-cantilever experiments after accounting for porosity on the one third of the beam length close to the clamp. This, in turn, provides an avenue to improve microscale experiments and their analysis in porous, anisotropic elastic materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Upcycling Polycrystalline LiNi1/3Mn1/3Co1/3O2 to High-Performance Large-Grained LiNi0.6Mn0.2Co0.2O2 via Simplified Polyol-Mediated Recycling

The escalating demand for lithium-ion batteries (LIBs) necessitates advanced recycling strategies that can address both resource scarcity and environmental impact. While conventional hydrometallurgy shows promise, it is challenged by complexity, impurity management, and environmental footprint. Here, we report a strategic polyol-metallurgy recycling process that efficiently transforms spent polycrystalline LiNi1/3Mn1/3Co1/3O2 (NMC111) into high-performance large-grained LiNi0.6Mn0.2Co0.2O2 (NMC622), offering dual benefits of compositional upcycling and morphology upgradation. Our approach leverages a polyol system with meticulous control over nickel salt addition and the precipitation process. This yields upcycled cathode materials possessing excellent structural integrity, well-defined large-grained particles (5-10?..mu..m), and robust electrochemical performance, including a specific capacity of ~182 mAh g-1 at C/10 and 88.0% capacity retention after 100 cycles. This facile and multifunctional process provides an environmental-friendly pathway for advanced cathode recycling, significantly contributing to a circular economy for LIBs through precise control over critical material attributes.

25 ENERGY STORAGE↗
DOE OSTI2021

Photoacoustic 3-D imaging of polycrystalline microstructure improved with transverse acoustic waves

Non-invasive fast imaging of grain microstructure of polycrystalline ceria with sub-micrometric spatial resolution is performed via time-domain Brillouin scattering. The propagation of a nanoacoustic pulse is monitored down to 8 µm deep in a 30 × 30 µm2 area. Grains boundaries are reconstructed in three-dimensions via a twostep processing method, relying on the wavelet synchro-squeezed transform and the alpha shape algorithm. Imaging contrast is improved by taking advantage of stronger sensitivity to anisotropy of transverse acoustic waves, compared with longitudinal waves. Utilization of transverse waves in the image processing reveals additional boundaries that are not discerned using longitudinal waves, confirmed by an electron backscattering diffraction pattern. A buried inclined interface between differently oriented grains is identified by monitoring changes in amplitude (phase) of the portion of the signal associated with transverse (longitudinal) waves. Estimates of the inclination angle of this interface prove the sensitivity of our laser ultrasonic method to image inclined boundaries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evaluating the Taylor hardening model in polycrystalline Ti using high energy X-ray diffraction microscopy

High energy X-ray diffraction microscopy (HEDM) was employed to index nearly 1000 grains in a polycrystalline Ti specimen and characterize their deformation during an incremental tensile test. For each grain, the positions of its associated diffraction peaks were used for analyzing its evolving crystal orientation and stress tensor. The azimuthal breadth of each peak at different load steps was measured, allowing measurement of initial yielding and providing an estimate of the dislocation density evolution in each grain. Furthermore, the Taylor hardening model was evaluated grain by grain using the above data, indicating that it can represent hardening in most grains. The yield stress and the strain hardening coefficient for all grains were statistically analyzed with respect to grain orientation, grain size, slip systems, and the surrounding neighborhood to examine how the yield stress and hardening are correlated.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Oxidation in Ca/K-1144 iron-based superconductors polycrystalline compounds

Iron-based superconductors (IBSCs) are a class of material under investigation for the development of superconducting wires in the low-temperature-high magnetic fields power application. Among the various families of IBSCs, the 1144 CaKFe$_4$As$_4$ compound is a promising material able to achieve outstanding superconducting properties with a cheap and simple chemical composition. Oxidation, in these compounds, is considered an obstacle for high intergranular critical current density, J c,GB . A study devoted to the evaluation of oxidation phenomena and their effects on the superconducting properties is thus needed in order to fully understand the involved mechanisms. From the evaluation of polycrystalline samples obtained by a mechanochemically assisted synthesis route, a degradation of the critical temperature and critical currents has been observed concurrently with oxygen accumulation at grain boundaries in open porosities. However, the crystalline structure at an atomic level seems not affected, as well as intragranular superconducting properties assessed by means of calorimetric methods. These results suggest that loss of superconducting properties in Ca/K-1144 compounds following oxidation is significantly associated with the worsening of grain connectivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗