Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical pumping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Optoelectronic property comparison for isostructural Cu 2 BaGeSe 4 and Cu 2 BaSnS 4 solar absorbers

To target mitigation of anti-site defect formation in Cu 2 ZnSnS 4–x Se x , a new class of chalcogenides, for which Ba or Sr (group 2) replace Zn (group 12), has recently been introduced for prospective solar absorber application. Cu 2 BaGeSe 4 (CBGSe) and Cu 2 BaSnS 4 (CBTS) are two such compounds, which share a common trigonal crystal structure (P3 1 space group) and similar quasi-direct band gap (~2 eV). While CBTS-based films have already been studied, there are no reports yet on films and solar cells based on related CBGSe. To identify key differences and similarities in the electronic properties between these two materials, electronic characteristics (e.g., carrier concentration, mobility, electron affinity, defect levels, recombination, and charge carrier kinetics) of vacuum-deposited CBGSe and CBTS films are compared using a variety of characterization methods. Hall effect measurements reveal that CBGSe films have relatively higher hole carrier concentration and lower mobility (3 × 10 15 cm –3 , 0.6 cm 2 V –1 s –1 ) compared to CBTS (5 × 10 12 cm –3 , 3.5 cm 2 V –1 s –1 ). Photoelectron spectroscopy yields low electron affinity values for both CBGSe (3.7 eV) and CBTS (3.3 eV), pointing to the necessity of pursuing low electron affinity buffer materials for both types of absorbers. At low temperatures, CBGSe films show free-exciton photoluminescence, as well as pronounced deep-level emission at ~1.4 eV, while CBTS films exhibit a strong bound-exciton signal with noticeably less intense deep-level emission than for CBGSe. Charge carrier kinetics, transport, and recombination properties of both types of films are also analyzed using optical-pump terahertz-probe spectroscopy and time-resolved microwave conductivity. The first CBGSe prototype solar cells (using chemical bath deposited CdS as a buffer layer) show a maximum of 1.5% efficiency with ~0.62 V open-circuit voltage. Furthermore, the measured properties point to possible limiting factors for CBGSe and related films for PV and optoelectronics and provide insights on possible approaches for improvement within this multinary chalcogenide family.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Demonstration of a 20‐W membrane‐external‐cavity surface‐emitting laser for sodium guide star applications

Abstract We present a record 20‐W continuous‐wave output power membrane‐external‐cavity surface‐emitting laser (MECSEL) double‐bonded to silicon carbide (SiC) heat spreaders emitting around 1178 nm. We achieved a maximum slope efficiency of 27.7% and an optical‐to‐optical efficiency of 26.7%. By utilising an intracavity birefringent filtre, the wavelength was tuned over 75 nm and maximum output power of 12.7 W was recorded at 1178 nm. This study shows the potential of MECSELs to achieve high‐performance and cost‐effective optically pumped semiconductor disk lasers targeting applications in sodium guide stars.

Priante, D.↗
DOE OSTI2020

Carrier recombination parameters in diamond after surface boron implantation and annealing

In this study, an optical pump–probe technique was used to detect spatial distribution of carrier lifetimes across the thickness of a high-quality diamond device structure. Two samples with as-received and boron implanted surfaces were compared to assess the role of implantation and related processing on carrier recombination mechanisms. It was found that the two implanted surfaces show very different behaviors despite undergoing the same treatment. At one of the surfaces, carrier lifetimes remained relatively unchanged, indicating surface recombination rates in the 102–103 cm/s range. At the other surface, carrier lifetimes were almost a magnitude lower and correlated with the locally detected nitrogen vacancy defect that was attributed to the elevated concentration of residual nitrogen.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Accuracy of XAS theory for unraveling structural changes of adsorbates: CO on Ni(100)

Studying surface reactions using ultrafast optical pump and X-ray probe experiments relies on accurate calculations of X-ray spectra of adsorbates for correct identification of the spectral signatures and their dynamical evolution. We show that experimental XAS can be well reproduced for the different binding sites in a static prototype system CO/Ni(100) at a standard DFT (GGA) level of theory, using a plane-wave basis and pseudopotentials. This validates its utility in analyzing ultrafast X-ray probe experiments. The accuracy of computed relative core level binding energies is about 0.2 eV, representing a lower limit for which spectral features can be resolved with this method. We also show that the commonly used Z +1 approximation gives very good core binding energy shifts overall. However, we find a discrepancy for CO adsorbed in the hollow site, which we assign to the significantly stronger hybridization in hollow bonding than in on-top.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2022

High thermal conductivity and ultrahigh thermal boundary conductance of homoepitaxial AlN thin films

Wurtzite aluminum nitride (AlN) has attracted increasing attention for high-power and high-temperature operations due to its high piezoelectricity, ultrawide-bandgap, and large thermal conductivity k. The k of epitaxially grown AlN on foreign substrates has been investigated; however, no thermal studies have been conducted on homoepitaxially grown AlN. In this study, the thickness dependent k and thermal boundary conductance G of homoepitaxial AlN thin films were systematically studied using the optical pump–probe method of frequency-domain thermoreflectance. Our results show that k increases with the thickness and k values are among the highest reported for film thicknesses of 200 nm, 500 nm, and 1 μm, with values of 71.95, 152.04, and 195.71 W/(mK), respectively. Our first-principles calculations show good agreement with our measured data. Remarkably, the G between the epilayer and the substrate reported high values of 328, 477, 1180, and 2590 MW/(m 2 K) for sample thicknesses of 200 nm, 500 nm, 1 μm, and 3 μm, respectively. The high k and ultrahigh G of homoepitaxially grown AlN are very promising for efficient heat dissipation, which helps in device design and has advanced applications in micro-electromechanical systems, ultraviolet photonics, and high-power electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ultrafast laser-induced spin–lattice dynamics in the van der Waals antiferromagnet CoPS 3

CoPS 3 stands out in the family of the van der Waals antiferromagnets XPS 3 (X = Mn, Ni, Fe, and Co) due to the unquenched orbital momentum of the magnetic Co 2+ ions, which is known to facilitate the coupling of spins to both electromagnetic waves and lattice vibrations. Here, using a time-resolved magneto-optical pump–probe technique, we experimentally study the ultrafast laser-induced dynamics of mutually correlated spins and lattice. It is shown that a femtosecond laser pulse acts as an ultrafast heater and, thus, results in the melting of the antiferromagnetic order. At the same time, the resonant pumping of the 4 T 1g → 4 T 2g electronic transition in Co 2+ ions effectively changes their orbital momentum, giving rise to a mechanical force that moves the ions in the direction parallel to the orientation of their spins, thus generating a coherent B g phonon mode at the frequency of about 4.7 THz.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Room temperature buffer gas beam of metastable state titanium atoms

We produce beams of neutral titanium (Ti) atoms in their metastable 3d3(F4)4sa5F5 state by laser ablation into He, N2, and Ar buffer gases. The high temperatures associated with the ablation process populate the a5F5 level without the need for optical pumping. Remarkably, we observe that Ti atoms in the a5F5 state survive thousands of collisions with He and Ar buffer gas atoms without being quenched to lower-energy states. We study the yield of Ti atoms when ablated into buffer gases of varying species and pressure, quantify quenching rates and diffusion cross sections based on simple models, and provide insight into optimal design parameters for an ablation cell. Using a 3.3 cm ablation cell with interchangeable exit apertures, we produce metastable atom beams and quantify their brilliance and velocity distributions as functions of buffer gas pressure.

Schrott, Jackson↗
DOE OSTI2025

Soft x-ray high-harmonic generation in an anti-resonant hollow core fiber driven by a 3 μ m ultrafast laser

High-harmonic upconversion driven by a mid-infrared femtosecond laser can generate coherent soft x-ray beams in a tabletop-scale setup. Here, we report on a compact ytterbium-pumped optical parametric chirped pulse amplifier (OPCPA) laser system seeded by an all-fiber front-end and employing periodically poled lithium niobate (PPLN) nonlinear media operated near the pulse fluence limits of current commercially available PPLN crystals. The OPCPA delivers 3 µm wavelength pulses with 775 µJ energy at 1 kHz repetition rate, with transform-limited 120 fs pulse duration, diffraction-limited beam quality, and ultrahigh 0.33% rms energy stability over >18 h. Using this laser, we generate soft x-ray high harmonics (HHG) in argon gas by focusing into a low-loss, high-pressure gas-filled anti-resonant hollow core fiber (ARHCF), generating coherent light at photon energies up to the argon L-edge (250 eV) and carbon K-edge (284 eV), with high beam quality and ∼1% rms energy stability. This work demonstrates soft x-ray HHG in a high-efficiency guided-wave phase matched geometry, overcoming the high losses inherent to mid-IR propagation in unstructured waveguides, or the short interaction lengths of gas cells or jets. The ARHCF can operate in the long term without damage and with the repetition rate, stability, and robustness required for demanding applications in spectromicroscopy and imaging. Finally, we discuss routes for further optimizing the soft x-ray HHG flux by driving He at higher laser intensities using either the signal (1.5 μm) or idler wavelengths (3 μm).

Femtosecond lasers↗
DOE OSTI2026

A compact in situ polarized 3He neutron spin filter for the diffractometer VULCAN at the Spallation Neutron Source

We have built and commissioned a compact in situ 3He polarizer based on spin-exchange optical pumping for the engineering materials diffractometer, named VULCAN, at the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory. The system achieved 78% 3He polarization with a short pump-up time constant of 2.2 h. Its first deployment in an in situ half-polarized neutron diffraction experiment on a magnetic shape memory alloy, Ni–Mn–Ga, revealed changes in magnetization coupled to deformation twinning under compression. With this new capability, VULCAN has become the first diffractometer at SNS capable of performing polarized neutron experiments, opening new opportunities to study a wider range of magnetism-related material behaviors under varied thermal, mechanical, electrical, and/or magnetic fields.

Fu, Sichao [ORNL] (ORCID:0009000846771640)↗
DOE OSTI2020

Nanosecond semiconductor disk laser emitting at 496.5 nm

An optically pumped semiconductor disk laser based on a heterostructure containing ten CdS/ZnSe coupled quantum wells with type-II band offsets is studied. The structure was grown by metalorganic vapour phase epitaxy (MOVPE) on a GaAs substrate. The peak power of the semiconductor disk laser achieved at room temperature under longitudinal pumping by a repetitively pulsed N{sub 2} laser was 0.75 W at a wavelength of 496.5 nm, a pulse duration of 3 ns, and a pulse repetition rate of 100 Hz. The slope efficiency of the disk laser was 2.7 %. The total divergence angle at a cavity length of 1.1 mm varied from 5 mrad near the lasing threshold to 15 mrad at the maximum pump power. (lasers)

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Sensing ultrashort electronic coherent beating at conical intersections by single-electron pulses

In a theoretical study, we present an ultrafast technique for probing time-dependent molecular charge densities. An ultrafast optical pump first brings the molecule into an electronic nonstationary state. This is followed by coherent inelastic scattering of a broadband single-electron probe pulse with a variable delay T, which is detected spectrally. The technique is applied to reveal phase-sensitive background-free coherent electron beating in the conical intersection passage in uracil and reveals the otherwise elusive coherent beating of strongly coupled electrons and nuclei.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Structural dynamics of laser-ionized cis-stilbene studied by ultrafast electron diffraction

Stilbene has been a model system for studying photoisomerization upon absorption of a UV photon. Although the dynamics of the first excited state have been investigated in great detail, the structural dynamics of cationic states remains largely experimentally unexplored. In this study, the dynamics following ionization via absorption of two UV photons was captured using ultrafast electron diffraction. cis-stilbene (CS) was optically pumped with 267 nm ultraviolet light with two different pump fluences and probed with 3.7 MeV electrons. We compare our experimental results to ab-initio multiple spawning simulations for single-photon excitation and molecular dynamics simulations for ionization in order to separate the contributions from the two channels. We found that with a fluence of 170 mJ cm −2 both the single and two-photon channels are present, while with higher fluence of 280 mJ cm −2 the two-photon channel dominates. We did not observe isomerization of the CS cation and found the main structural motion a to be a vibration of the phenyl rings about the central C–C bond.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2024

Is Ba 3 In 2 O 6 a high- T c superconductor?

It has been suggested that Ba 3 In 2 O 6 might be a high-Tc superconductor. Experimental investigation of the properties of Ba 3 In 2 O 6 was long inhibited by its instability in air. Recently epitaxial Ba 3 In 2 O 6 with a protective capping layer was demonstrated, which finally allows its electronic characterization. The optical bandgap of Ba3In2O6 is determined to be 2.99 eV in-the (001) plane and 2.83 eV along the c-axis direction by spectroscopic ellipsometry. First-principles calculations were carried out, yielding a result in good agreement with the experimental value. Various dopants were explored to induce (super-)conductivity in this otherwise insulating material. Neither A- nor B-site doping proved successful. The underlying reason is predominately the formation of oxygen interstitials as revealed by scanning transmission electron microscopy and first-principles calculations. Additional efforts to induce superconductivity were investigated, including surface alkali doping, optical pumping, and hydrogen reduction. To probe liquid-ion gating, Ba 3 In 2 O 6 was successfully grown epitaxially on an epitaxial SrRuO 3 bottom electrode. So far none of these efforts induced superconductivity in Ba 3 In 2 O 6 , leaving the answer to the initial question of whether Ba 3 In 2 O 6 is a high-T c superconductor to be 'no' thus far.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Effects of head modeling errors on the spatial frequency representation of MEG

Abstract Objectives. We aim to investigate the effects of head model inaccuracies on signal and source reconstruction accuracies for various sensor array distances to the head. This allows for the assessment of the importance of head modeling for next-generation magnetoencephalography (MEG) sensors, optically-pumped magnetometers (OPM). Approach. A 1-shell boundary element method (BEM) spherical head model with 642 vertices of radius 9 cm and conductivity of 0.33 S m −1 was defined. The vertices were then randomly perturbed radially up to 2%, 4%, 6%, 8% and 10% of the radius. For each head perturbation case, the forward signal was calculated for dipolar sources located at 2 cm, 4 cm, 6 cm and 8 cm from the origin (center of the sphere), and for a 324 sensor array located at 10 cm to 15 cm from the origin. Equivalent current dipole (ECD) source localization was performed for each of these forward signals. The signal for each perturbed spherical head case was then analyzed in the spatial frequency domain, and the signal and ECD errors were quantified relative to the unperturbed case. Main results. In the noiseless and high signal-to-noise ratio (SNR) case of approximately ≥6 dB, inaccuracies in our spherical BEM head conductor models lead to increased signal and ECD inaccuracies when sensor arrays are placed closer to the head. This is true especially in the case of deep and superficial sources. In the noisy case however, the higher SNR for closer sensor arrays allows for an improved ECD fit and outweighs the effects of head geometry inaccuracies. Significance. OPMs may be placed directly on the head, as opposed to the more commonly used superconducting quantum interference device sensors which must be placed a few centimeters away from the head. OPMs thus allow for signals of higher spatial resolution to be captured, resulting in potentially more accurate source localizations. Our results suggest that an increased emphasis on accurate head modeling for OPMs may be necessary to fully realize its improved source localization potential.

Yeo, Wan-Jin (ORCID:0000000241417123)↗
DOE OSTI2023

Single-trial classification of evoked responses to auditory tones using OPM- and SQUID-MEG

Abstract Objective. Optically pumped magnetometers (OPMs) are emerging as a near-room-temperature alternative to superconducting quantum interference devices (SQUIDs) for magnetoencephalography (MEG). In contrast to SQUIDs, OPMs can be placed in a close proximity to subject’s scalp potentially increasing the signal-to-noise ratio and spatial resolution of MEG. However, experimental demonstrations of these suggested benefits are still scarce. Here, to compare a 24-channel OPM-MEG system to a commercial whole-head SQUID system in a data-driven way, we quantified their performance in classifying single-trial evoked responses. Approach. We measured evoked responses to three auditory tones in six participants using both OPM- and SQUID-MEG systems. We performed pairwise temporal classification of the single-trial responses with linear discriminant analysis as well as multiclass classification with both EEGNet convolutional neural network and xDAWN decoding. Main results. OPMs provided higher classification accuracies than SQUIDs having a similar coverage of the left hemisphere of the participant. However, the SQUID sensors covering the whole helmet had classification scores larger than those of OPMs for two of the tone pairs, demonstrating the benefits of a whole-head measurement. Significance. The results demonstrate that the current OPM-MEG system provides high-quality data about the brain with room for improvement for high bandwidth non-invasive brain–computer interfacing.

Iivanainen, Joonas (ORCID:0000000160344604)↗
DOE OSTI2023

Polarized fusion and potential in situ tests of fuel polarization survival in a tokamak plasma

Abstract The use of spin-polarized fusion fuels would provide a significant boost towards the ignition of a burning plasma. The cross section for D + T → α + n, would be increased by 1.5 if the fuels were injected with parallel polarization. Furthermore, our simulations demonstrate additional non-linear power gains in large-scale machines such as ITER, due to increased alpha heating. Such benefits require the survival of spin polarizations for periods comparable to the particle confinement time. During the 1980s, calculations predicted that polarizations could survive a plasma environment, although concerns persisted regarding the cumulative impacts of wall recycling. In that era, technical challenges prevented direct tests and left the large scale fueling of a power reactor beyond reach. Over the last decades, this situation has changed dramatically. Detailed simulations of ITER have predicted negligible wall recycling in a high-power reactor, and recent advances in laser-driven sources project the capability of producing large quantities of ∼100% polarized D and T. The remaining crucial step is an in-situ demonstration of polarization survival in a plasma. For this, we outline a measurement strategy using the isospin-mirror reaction, D + 3 He → α + p. Polarized 3 He avoids the complexities of handling tritium, while encompassing the same spin-physics. We evaluate two methods of delivering deuterium, using dynamically polarized Lithium-Deuteride (with vector polarization P V D of 70%) or frozen-spin Hydrogen-Deuteride (with P V D of 40%), together with a method of injecting optically-pumped 3 He (with 65% polarization). Pellets of these materials all have long polarization decay times (∼6 min for LiD at 2 K, ∼2 months for HD at 2 K, and ∼3 d for 3 He at 77 K), all far greater than a plasma shot in a research tokamak such as DIII-D (∼20 s). Both species can be propelled from a single cryogenic injection gun. We review plasma requirements and strategies for detecting polarization survival. Polarization alters both fusion yields and the angular distribution of fusion products, and each of these provides a potential signal. In this paper we simulate a selection of shots with similar characteristics in a future high-T ion H plasma, and find ratios of yields from shots with fuel spins parallel and antiparallel reaching 1.3 (HD + 3 He) to 1.6 (LiD + 3 He) over a wide range of poloidal angles. (A companion paper finds sensitivity to fusion product angular distributions as reflected in the pitch angles of protons and alphas reaching the plasma facing wall.)

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

MEOP based 3 He polarization and injection system for experiments below 1 K

Metastability exchange optical pumping (MEOP) is a widely used technique for producing polarized 3 He. In connection with an experiment to search for the electric dipole moment of the neutron (nEDM) we have built a MEOP based 3 He polarization and injection system to prepare 80 % polarized 3 He at room temperature which will be injected into a ∼ 400 mK measurement cell filled with superfluid 4 He. We describe the polarization and injection system, which is designed to allow for final concentrations of 10 -8 –10 -10 of 80% polarized 3 He in the superfluid filled measurement cell. Only ≈ 0.72% polarization loss due to gradients is expected during injection.

Gas systems and purification↗