Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “monotonicity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An experimental and kinetic modeling study of NO x sensitization on methane autoignition and oxidation

An experimental and kinetic modeling study of the influence of NO x (i.e. NO 2 , NO and N 2 O) addition on the ignition behavior of methane/‘air’ mixtures is performed. Ignition delay time measurements are taken in a rapid compression machine (RCM) and in a shock tube (ST) at temperatures and pressures ranging from 900–1500 K and 1.5–3.0 MPa, respectively for equivalence ratios of 0.5–2.0 in ‘air’. The conditions chosen are relevant to spark ignition and homogeneous charge compression ignition engine operating conditions where exhaust gas recirculation can potentially add NO x to the premixed charge. The RCM measurements show that the addition of 200 ppm NO 2 to the stoichiometric CH 4 /oxidizer mixture results in a factor of three increase in reactivity compared to the baseline case without NOx for temperatures in the range 600–1000 K. However, adding up to 1000 ppm N 2 O does not show any appreciable effect on the measurements. The promoting effect of NO 2 was found to increase with temperature in the range 950–1150 K, while the sensitization effect decreases at higher pressures. The experimental results measured are simulated using NUIGMech1.2 comprising an updated NO x sub-chemistry in this work. A kinetic analysis indicates that the competition between the reactions ĊH 3 + NO 2 ↔ CH 3 Ȯ + NO and ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), the former being a propagation reaction and the latter being a termination reaction governs NO x sensitization on CH 4 ignition. Recent calculations by Matsugi and Shiina (A. Matsugi, H. Shiina, J. Phys. Chem. A. 121 (2017) 4218–4224) for the nitromethane formation reaction CH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), together with the recently calculated rate constants for HONO/HNO 2 reactions significantly improve ignition delay time predictions in the temperature range 600–1000 K. Furthermore, the experiments with NO addition reveal a non-monotonous sensitization impact on CH 4 ignition at lower temperatures with NO initially acting as an inhibitor at low NO concentrations and then as a promoter as NO concentrations increase in the mixture. This non-monotonous trend is attributed to the role of the chain-termination reaction ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M) and the impact of NO on the transition to the chain-branching steps CH 2 O + HȮ 2 ↔ HĊO + H 2 O 2 , H 2 O 2 (+M) ↔ ȮH + ȮH (+M), HĊO ↔ CO + Ḣ followed by CO + O 2 ↔ CO 2 + Ö and Ḣ + O 2 ↔ Ö + ȮH. NUIGMech1.2 is systematically validated against the new ignition delay measurements taken here together with species measurements and high temperature ignition delay time data available in the literature for CH 4 /oxidizer mixtures diluted with NO 2 /N 2 O/NO and is observed to accurately capture the sensitization trends.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Woven ceramic matrix composite surrogate model based on physics-informed recurrent neural network

A recurrent neural network (RNN) based surrogate model is developed to emulate the nonlinear constitutive behavior of woven ceramic matrix composites (CMCs) driven by matrix damage at multiple length scales. Physics-informed constraints are introduced into the surrogate model through regularization to ground the prediction in physics and improve its predictive capabilities. Training data is generated using the multiscale generalized method of cells (MSGMC) approach coupled with a matrix damage model. This coupling permits simulating the nonlinear behavior of woven CMCs based on constituent response at the micro-, meso-, and macroscales. The multiscale repeating unit cell is loaded under non-monotonic conditions including multiple load / unload cycles and tension / compression. The fiber volume fraction as well as the intra- and intertow void volume fractions are also varied in the generation of training data. Therefore, the RNN-based surrogate model is tasked with predicting, as a function of variable input strain sequence and fiber and void volume fractions, the resulting stress versus strain response while satisfying physical constraints such as positive semi-definiteness of the tangent stiffness matrix and linear elastic unloading. Further, the trained surrogate model effectively matches the stress versus strain response and successfully predicts the tangent modulus throughout the loading regime. Neural network based surrogate models can offer efficient alternatives to running computationally intensive multiscale material models to simulate the nonlinear response of large structural models. Therefore the presented work provides evidence towards the feasibility of developing, training, and running such models for CMCs with complex architectures, nonlinear multiaxial material response, and under non-monotonic loading conditions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Testing and modeling of CLT-to-CLT joints made using hardwood dowels and screws with varying spacing

With the increasing popularity of mass timber, utilizing large-diameter wood screws and hardwood dowels can offer an easy and cost-efficient way to join structural elements. However, the existing research on hardwood dowels is limited to single fastener joints under monotonic loading. No research is available on the group effects of joints with multiple hardwood dowels. Here, this paper presents the results of 96 monotonic and cyclic single-shear plane CLT-to-CLT joint tests with hardwood dowels (Red Oak and Yellow Birch, 25.4 mm diameter) and self-tapping wood screws (8 mm diameter) in Grand-Fir CLT, where screws were inserted both perpendicular and at a 45-degree angle to the grain for comparison to hardwood dowels. The study evaluated the mechanical properties of the joints by changing fastener spacing. Mechanical properties such as yielding and peak strength, displacement, elastic and yielding stiffness, and ductility were evaluated. The results showed equal strength and stiffness properties for hardwood dowels comparable with large-diameter screws. Additionally, the hardwood dowel joints demonstrated moderate ductility properties. The strength and stiffness of the tested joints were compared with analytical equations found in the literature by considering the group action factor of the fasteners. Lastly, a nonlinear force-displacement model was presented and compared to the experimental results and analytical calculations, which gives the possibility to predict and optimize the mechanical behavior of hardwood dowel and screw joints with varying numbers and spacing between fasteners.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On Anomaly Detection for Transactive Energy Systems with Competitive Market

Two anomaly-detection criteria are proposed for transactive energy systems with competitive markets. Participants of transactive energy systems seek an optimal power allocation through hybrid economic-control methods to facilitate the integration of various types of distributed energy resources to power distribution systems. In transactive energy systems, every participant is assumed to be a rational entity, and consumers have diminishing marginal utility and suppliers have increasing marginal cost. With the first proposed anomaly-detection criterion, the monotonicity of marginal cost and marginal utility are examined. The impact of line flow constraints is also taken into consideration. Then, the second anomaly-detection criterion is proposed for TESs with marginal cost and marginal utility which change faster than a certain rate. The second criterion is more accurate than the first one for TES with marginal cost and marginal utility which change faster than a certain rate, but it requires the knowledge of that rate. Neither criteria requires more data than those necessary to find the optimal power allocation and the market-clear price in a transactive energy system. Therefore, the proposed criteria do not disclose any more data than necessary. As the monotonicity of marginal cost and marginal utility in a TES with competitive markets results in convex objective functions in an optimization problem and strongly convex ones when marginal cost and marginal utility changes faster than a certain rate, the two detection criteria are also applicable to anomaly detection of general convex optimization problems. Simulations are carried out to show the efficacy of the proposed criteria to detect anomalies caused by cyberattacks.

Wang, Peng↗
DOE OSTI2024

A block-spectral adaptive H-/$p$-refinement strategy for shock-dominated problems

An adaptive H-/p-refinement strategy using a novel sensor is devised and tested in a block-spectral compressible Euler code equipped with adaptive-mesh refinement (AMR) and high-order flux-reconstruction numerics. At each Gauss quadrature point (or solution point) within each spectral block (or mesh element) the discrete velocity jump ΔU = ∂U/∂y 1 Δy 1 + ∂V/∂y 2 Δy 2 + ∂W/∂y 3 Δy 3 is calculated and normalized by the local speed of sound, a. Here, the grid spacing, Δx i , is calculated in each direction as the distance between auxiliary Gauss-Lobatto points, staggered relative to the solution points. The polynomial order is increased from p = 0 to p = p max in regions of weak compression, (ΔU/a) crit < ΔU/a < 0 and kept at p = p max in regions of flow expansion ΔU/a ≥ 0, while staying at the H = 0 base mesh level. Regions experiencing strong compressions, i.e. ΔU/a < (ΔU/a) crit , are H-refined up to H = H max where H max is applied at the location of maximum compression, ΔU/a = min(ΔU/a) in the domain, while keeping p = 0 to guarantee robustness and monotonicity of the solution in the H refined region. The critical value of (ΔU/a) crit = -0.06 is found to effectively separate smooth and non-smooth solution regions, supported by a 1D detonation initiation test case in ideal gas and a shock-to-detonation transition in high explosives. Using this value, the Sod shock tube, Shu-Osher problem, double Mach reflection and a 2D detonation in a high-explosive are simulated with the proposed adaptive H-/p-refinement. In the Sod shock tube case, p-refinement resolves the (weak) contact discontinuity while H-refinement enhances the grid resolution in the shock exploiting the monotonicity of the p = 0 reconstruction. For the Shu-Osher problem, p-refinement captures the small-scale oscillations trailing the shock that would be otherwise attenuated, while H-refinement triggered by the ΔU-sensor appropriately tracks the shock. In the double Mach reflection problem, H-refinement confines the numerical diffusion around the reflected shock while p-refinement recaptures many physical features trailing the shock. Finally, in the 2D high-explosive detonation case, H-refinement follows the leading shock and resolves the curvature of the detonation wave, while p-refinement adds resolution to the trailing reaction zone. Finally, the proposed methodology is tested in a detonation-wave propagation test case in high-explosives with numerical predictions comparing favorably against experiments.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Spin canting of Ni/CoO/Fe films grown on curved MgO(0 0 1) substrate

Using element-resolved x-ray magnetic circular dichroism (XMCD) and x-ray magnetic linear dichroism (XMLD) measurements, we determined the spin orientations of Ni, CoO and Fe films in Ni/CoO/Fe films grown on a curved MgO(0 0 1) substrate. We find that the vicinal surface of MgO(0 0 1) substrate results in a spin canting towards out-of-plane direction in the Ni and CoO films as a result of the interfacial coupling. The Ni spin canting angle increases monotonically with the vicinal angle in the studied range of 0–17° and the CoO spin canting angle increases more rapidly towards saturation only at a few degrees of the vicinal angle. The uniaxial magnetic anisotropy induced in the Ni layer by the Ni/CoO interfacial coupling is quantitatively determined and is shown to increase monotonically with the vicinal angle. Our result provides a new pathway for tailoring the spin orientation by modifying the substrate surface symmetry in combining with the ferromagnetic/antiferromagnetic interfacial interaction in thin-film based spintronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multiscale study of helium diffusion in Ni-Cr alloys: Short-range trapping versus long-range channeling

Ni-Cr alloys are widely employed as structural materials in fast nuclear reactors but are vulnerable to high-temperature helium (He) embrittlement (HTHE) under fast neutron irradiation. A comprehensive understanding of He diffusion in Ni-Cr alloys, which governs the kinetics of HTHE, is therefore essential for developing resilient materials and preventing failure. In this work, we reveal the underlying mechanisms of He diffusion in pure Ni and Ni-Cr alloys by integrating density functional theory (DFT) with atomic kinetic Monte Carlo (AKMC) simulations. Our findings uncover a non-monotonic dependence of He diffusivity on Cr concentration, contradicting the monotonic trends predicted by DFT-parameterized theories. At low Cr concentrations, He diffusion is dominated by short-range trapping, characterized by multiple trapping sites and a distinct mechanism within the first nearest neighbor of Cr, differing from that in pure Ni. At high Cr concentrations, these local traps become interconnected, forming long-range fast diffusion channels that enhance He mobility. The competition between localized trapping and extended channeling results in a diffusivity that first decreases, then increases with rising Cr content. These atomic-scale insights offer critical guidance for the design of radiation-tolerant Ni-based alloys. Moreover, the combined DFT-AKMC methodology and the concept of random walker diffusion through interconnected energy basins present a broadly applicable framework for studying transport phenomena in disordered systems.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Molecular dynamics study of interstitial He clusters in nickel

This study presents a molecular dynamics analysis focusing on the behavior of interstitial helium (He) clusters in nickel (Ni), examining their formation, stability, and migration energetics. Consistent with previous research, we found that the binding energies of interstitial helium within a helium cluster are positive and increase with the cluster size, indicating a preference for helium atoms to cluster together. However, our findings also reveal that while the formation energy increases monotonically with cluster size, the increase in binding energy is non-monotonic. Importantly, small He clusters were observed to be thermally unstable at reactor operational temperatures (approximately 600 K), with the He 2 cluster exhibiting instability even at room temperature. With a binding energy of 0.49 eV for a He 4 cluster, we hypothesize that for helium bubbles to form via homogeneous nucleation (i.e., through trap mutation) at reactor operating temperatures, the helium concentration must be high enough to facilitate the formation of helium clusters of at least size 4 or larger. As expected, interstitial helium and small helium clusters are highly mobile. This mobility was observed not only at room temperature but also at temperatures as low as approximately 200 K. Furthermore, the mean squared displacement method has been utilized to determine the migration barriers and the corresponding prefactors for clusters ranging from He 1 to He 6

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Numerical modeling of plasma assisted deflagration to detonation transition in a microscale channel

Here, this work numerically studies the plasma assisted deflagration to detonation transition (DDT) of H 2 /O 2 mixtures in a microscale channel with detailed chemistry and transport. The results show that the DDT onset time is non-monotonically dependent on the discharge pulse number. The DDT is accelerated with small pulse numbers, whereas retarded with large ones. Two different DDT regimes, respectively at a small and large plasma discharge number, via acoustic choking of the burned gas and plasma-enhanced reactivity gradient without acoustic choking, are observed. Without plasma discharge, pronounced pressure and temperature gradients in front of the flame are generated by acoustic compression after the choking of the burned gas, triggering DDT via autoignition. With small plasma pulse numbers, the plasma-generated species enhance the ignition kinetics and lead to an increased reactivity in the boundary layer. After the choking of the burned gas, the plasma-enhanced reactivity advances the sequence of autoignition near the wall, strengthens ignition-shock wave coupling, and accelerates DDT. However, with a large discharge pulse number, a direct autoignition initiating DDT can occur without the acoustic choking of the burned gas due to the strongly accelerated reactivity and elevated temperature. In this case, DDT onset is retarded because the elevated temperature increases sonic velocity and the increased reactivity accelerates fuel oxidation in front of the flame, decelerating the formation of a leading shock and subsequent pressure buildup ahead of the flame. The present modeling reveals that no matter with or without plasma discharge, DDT is initiated by autoignition in thermal, pressure, and reactivity gradient fields via the Zel'dovich gradient mechanism. The acoustic choking of the burned gas may not be the necessary condition of DDT with strong plasma-enhanced reactivity gradient. This work provides an answer to the experimentally observed non-monotonic DDT onset time by plasma, which provides guidance to control DDT in advanced detonation engines and fire safety of hydrogen-fueled catalytic reactors in microchannels by non-equilibrium plasma discharge.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

A surprising proliferation of detwinning in β -tin at extreme loading rates

Integrating data from dynamic compression experiments of condensed matter across three national laboratories has led to insight and quantitative calibration of materials strength over decades of loading rate. For many materials, a single strength model (such as PTW) is sufficient to capture the flow-stress strain rate relationship which is monotonic. Here, we show here that β -tin, a tetragonal metal, exhibits dramatic deviations from this behavior. Naive fitting to a single PTW model is insufficient to capture the behavior; indeed, such resulting inferred flow stress versus strain exhibits a non-monotonic behavior. We suggest a resolution to this by proposing that in β -tin there are important Bauschinger effects arising from favorable conditions for twinning and detwinning. A simple yield surface model when paired with PTW hardening captures the experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Removing Basis Set Incompleteness Error in Finite-Temperature Electronic Structure Calculations: Two-Electron Systems

We investigate the basis-set-size dependence for quantities related to interacting electrons in the canonical ensemble. Calculations are performed using exact diagonalization (finite temperature full configuration interaction method) on two-electron model systems–the uniform electron gas (UEG) and the helium atom. Our data reproduce previous observations of a competition for how the internal energy converges between the ground-state correlation energy and the high-temperature kinetic energy. We explore how this can be related to component parts of the internal energy including kinetic, exchange, and correlation energies and show there is surprising nuance in how this can be broken down into mostly monotonically converging quantities. We also show that separation of the free energy into a free energy with/without correlation allows for monotonic convergence with basis set size due to the variational principle. We find that the free energy convergence matches the previously observed convergence properties of the internal energy. We discuss the free energy divergence that happens when converging a finite basis analytical hydrogen atom to the complete basis set limit and compare this to the energies of a helium atom in a large periodic box. Reducing the box size, we saw convergence trends for the helium atom that were similar to the UEG.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Notable Contributions of Aerosols to the Predictability of Hail Precipitation

There is an increasing concern of the uncertainty produced by aerosols in forecasting precipitation including hail precipitation. This study provides an assessment of the uncertainties in hail and total precipitation by varying initial cloud condensation nuclei (CCN) number concentration (CCNC) and meteorological conditions based on 1200 cloud-resolving simulations of an idealized hailstorm. Although the meteorological perturbations produce large uncertainties in hail precipitation (including rate and maximum hail size) as well as total precipitation, varying CCNC by an order of magnitude can cause even larger uncertainties, especially pairing with the thermodynamics perturbation (i.e., potential temperature and water vapor). Changing CCNC modifies the predictability of hail precipitation, with a higher predictability in moderate polluted environments compared with the very clean and polluted environments. Increasing CCNC consistently leads a non-monotonic response of ensemble mean with an optimal CCNC for hail precipitation but a monotonic decreasing response of total precipitation with the various meteorological perturbations, meaning the initial meteorological perturbations does not qualitatively change the aerosol effects. Investigation with 10-fold reduced initial perturbation further supports the large CCN effects are not dependent of metrological perturbations. The findings suggest the importance of considering CCN effects in severe weather simulations and forecasting.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Response of Extreme Rainfall to Atmospheric Warming and Wetting: Implications for Hydrologic Designs Under a Changing Climate

Understanding the processes of rainfall extremes and their response to anthropogenic climate change is pivotal for improved adaptation of unprecedented flood hazards around the world. Here we take the record-breaking 20 July 2021 storm over central China as an example. We investigate the response of this particular storm to atmospheric warming (i.e., increase in air temperature) and wetting (i.e., increase in atmospheric moisture content) based on a series of convection-permitting model simulations. Our results show non-monotonic changes of the space-time rainfall variability to either increased temperature or atmospheric moisture content. The most extreme rain rate is produced when relative humidity is increased by 20~40 % or temperature is increased by less than 2°C. The non-monotonic rainfall response is more clearly revealed at fine spatial (100-1000 km 2 ) and temporal scales (less than 6 hours) rather than over the entire domain (~10 4 km 2 ) and aggregated over the storm duration (around two days). This is mainly attributable to the distinct feedbacks from atmospheric dynamics (i.e., moisture convergence and interaction with regional topography) rather than regulated by thermodynamic changes alone. Furthermore, atmospheric warming poses notable changes in the vertical structure of storm cells, contributing to reduced areal reduction factors at small spatial scales and short durations, while atmospheric wetting additionally modifies storm evolution properties. Our modeling analyses challenge the existing practices for hydrologic designs under a changing climate, highlighting particular vulnerability for cities or small basins to short-duration rainfall extremes and the resultant flash flood hazards.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Anomalous electronic transport in high-mobility Corbino rings

We report low-temperature electronic transport measurements performed in two multi-terminal Corbino samples formed in GaAs/Al-GaAs two-dimensional electron gases (2DEG) with both ultra-high electron mobility ( ≳ 20 × 10 6 cm 2 / Vs) and with distinct electron density of 1.7 and 3.6 × 10 11 cm -2 . In both Corbino samples, a non-monotonic behavior is observed in the temperature dependence of the resistance below 1 K. Surprisingly, a sharp decrease in resistance is observed with increasing temperature in the sample with lower electron density, whereas an opposite behavior is observed in the sample with higher density. To investigate further, transport measurements were performed in large van der Pauw samples having identical heterostructures, and as expected they exhibit resistivity that is monotonic with temperature. Finally, we discuss the results in terms of various lengthscales leading to ballistic and hydrodynamic electronic transport, as well as a possible Gurzhi effect.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Screening of resonant magnetic perturbation fields assuming various plasma flow models

A recently updated version of the MARS-F code [Y. Q. Liu et al., Phys. Plasmas 7, 3681 (2000); L. Li et al., Phys. Plasmas 25, 082512 (2018); and G. L. Xia et al., Nucl. Fusion 59, 126035 (2019)] is utilized to numerically investigate the plasma screening effect on the applied resonant magnetic perturbation (RMP) field, assuming various equilibrium flow models, including the toroidal flow, the parallel flow and their combinations, and poloidal and toroidal projections of the parallel flow. A parallel equilibrium flow with a uniform radial profile is found to have no effect on plasma screening of the RMP field. A sheared parallel flow, however, does change plasma screening. The poloidal projection of the parallel flow weakens plasma screening in the resistive-inertial regime. The effect on the favorable average curvature regime is found, however, to be non-monotonic. With the increasing flow speed, the poloidal projection first weakens Glasser-Green-Johnson (GGJ)-screening. Further increase in the flow speed results in enhanced GGJ-screening again. This non-monotonic behavior is related to the perturbed parallel shielding current, which appears also off the mode rational surface at fast flow due to additional resonances between the RMP perturbation and the sound wave continuum. These results indicate that flow induced plasma screening to the RMP field can have complicated characteristics, which, in turn, can have implications on the RMP field penetration into the plasma in experiments for controlling the edge localized modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Thermal expansion of plasma-exposed tungsten

We report results from a systematic analysis of thermal expansion of plasma-exposed tungsten based on molecular-dynamics simulations using models of tungsten with distributions of helium (He) bubbles in the tungsten matrix. We distinguish between two approaches of filling the bubbles with He, where the amount of He in the bubble can or cannot vary with temperature. In the former case, the thermal expansion coefficient decreases monotonically with the porosity and He content of the tungsten matrix, while in the latter case, the thermal expansivity increases monotonically with increasing porosity and He content. The latter condition, where the He content in the bubble is determined at the implantation temperature and remains constant with varying temperature in the tungsten matrix, is consistent with He species transport in tungsten used as a plasma-facing component (PFC) in nuclear fusion reactors and implies the development of biaxial compressive thermal strains in the PFC material that contribute to accelerating the growth of a nanostructure on PFC tungsten surfaces. Furthermore our analysis advances the fundamental understanding of thermal expansion in PFC tungsten and contributes to the development of a thermophysical property database for properly incorporating effects of realistic heat loads into modeling the dynamical response of PFC tungsten under fusion reactor operating conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Memory in aging colloidal gels with time-varying attraction

Here, we report a combined rheology, x-ray photon correlation spectroscopy, and modeling study of gel formation and aging in suspensions of nanocolloidal spheres with volume fractions of 0.20 and 0.43 and with a short-range attraction whose strength is tuned by changing temperature. Following a quench from high temperature, where the colloids are essentially hard spheres, to a temperature below the gel point, the suspensions form gels that undergo aging characterized by a steadily increasing elastic shear modulus and slowing, increasingly constrained microscopic dynamics. The aging proceeds at a faster rate for stronger attraction strength. When the attraction strength is suddenly lowered during aging, the gel properties evolve non-monotonically in a manner resembling the Kovacs effect in glasses, in which the modulus decreases and the microscopic dynamics become less constrained for a period before more conventional aging resumes. Eventually, the properties of the gel following the decrease in attraction strength converge to those of a gel that has undergone aging at the lower attraction strength throughout. The time scale of this convergence increases as a power law with the age at which the attraction strength is decreased and decreases exponentially with the magnitude of the change in attraction. A model for gel aging in which particles attach and detach from the gel at rates that depend on their contact number reproduces these trends and reveals that the non-monotonic behavior results from the dispersion in the rates that the populations of particles with different contact number adjust to the new attraction strength.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Heat transport with a twist

Despite the desirability of polymers for use in many products due to their flexibility, light weight, and durability, their status as thermal insulators has precluded their use in applications where thermal conductors are required. However, recent results suggest that the thermal conductance of polymers can be enhanced and that their heat transport behaviors may be highly sensitive to nanoscale control. Here we use non-equilibrium molecular dynamics simulations to study the effect of mechanical twist on the steady-state thermal conductance across multi-stranded polyethylene wires. We find that a highly twisted double-helical polyethylene wire can display a thermal conductance up to three times that of its untwisted form, an effect which can be attributed to a structural transition in the strands of the double helix. We also find that in thicker wires composed of many parallel strands, adding just one twist can increase its thermal conductance by over 30%. However, we find that unlike stretching a polymer wire, which causes a monotonic increase in thermal conductance, the effect of twist is highly non-monotonic, and certain amounts of twist can actually decrease the thermal conductance. Finally, we apply the Continuous Chirality Measure (CCM) in an attempt to explore the correlation between heat conductance and chirality. The CCM is found to correlate with twist as expected, but we attribute the observed heat transport behaviors to structural factors other than chirality.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗