SEARCH · Engineering Papers

Results for “modal identification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Rotorcraft Blade Mode Damping Identification from Random Responses Using a Recursive Maximum Likelihood Algorithm

An on line technique is presented for the identification of rotor blade modal damping and frequency from rotorcraft random response test data. The identification technique is based upon a recursive maximum likelihood (RML) algorithm, which is demonstrated to have excellent convergence characteristics in the presence of random measurement noise and random excitation. The RML technique requires virtually no user interaction, provides accurate confidence bands on the parameter estimates, and can be used for continuous monitoring of modal damping during wind tunnel or flight testing. Results are presented from simulation random response data which quantify the identified parameter convergence behavior for various levels of random excitation. The data length required for acceptable parameter accuracy is shown to depend upon the amplitude of random response and the modal damping level. Random response amplitudes of 1.25 degrees to .05 degrees are investigated. The RML technique is applied to hingeless rotor test data. The inplane lag regressing mode is identified at different rotor speeds. The identification from the test data is compared with the simulation results and with other available estimates of frequency and damping.

Molusis, J. A.↗

NASA NTRS1993

Dynamic tests on the NASA Langley CSI evolutionary model

A modal analysis study, representing one of the anticipated 'Cooperative Spacecraft Structural Dynamics Experiments on the NASA Langley CSI Evolutionary Model', was carried out as a sub-task under the NASA/DLR collaboration in dynamics and control of large space systems. The CSI evolutionary testbed (CEM) is designed for the development of Controls-Structures Interaction (CSI) technology to improve space science platform pointing. For orbiting space structures like large flexible trusses, new identification challenges arise due to their specific dynamic characteristics (low frequencies and high modal density) on the one hand, and the limited possibilities of exciting such structures and measuring their responses on orbit on the other. The main objective was to investigate the modal identification potential of several different types of forcing functions that could possibly be realized with on-board excitation equipment using a minimum number of exciter locations as well as response locations. These locations were defined in an analytical test prediction process used to study the implications of measuring and analyzing the responses thus produced. It turned out that broadband excitation is needed for a general modal survey, but if only certain modes are of particular interest, combinations of exponentially decaying sine functions provide favorable excitation conditions as they allow to concentrate the available energy on the modes being of special interest. From a practical point-of-view structural nonlinearities as well as noisy measurements make the analysis more difficult, especially in the low frequency range and when the modes are closely spaced.

Troidl, H.↗

NASA NTRS1979

The dual momentum control device for large space systems - An example of distributed system adaptive control

One area in which large space systems require new technology is attitude control. The paper presents an adaptive control philosophy applicable to the control of distributed systems. An adaptive control system is described for stabilization of the flexible modes of a spinning ring. The system consists of a modal decomposition and identification subsystem, a gain adjustment subsystem, and a feedback control subsystem. Simulations are presented illustrating the adaptive capability of the system. The adaptive controller did produce stable results by quickly identifying the parameter differences and adjusting the feedback controller gains.

Montgomery, R. C.↗

NASA NTRS1985

Adaptive identification and control of structural dynamics systems using recursive lattice filters

A new approach for adaptive identification and control of structural dynamic systems by using least squares lattice filters thar are widely used in the signal processing area is presented. Testing procedures for interfacing the lattice filter identification methods and modal control method for stable closed loop adaptive control are presented. The methods are illustrated for a free-free beam and for a complex flexible grid, with the basic control objective being vibration suppression. The approach is validated by using both simulations and experimental facilities available at the Langley Research Center.

Sundararajan, N.↗

NASA NTRS1988

A summary of recent NASA/Army contributions to rotorcraft vibrations and structural dynamics technology

The requirement for low vibrations has achieved the status of a critical design consideration in modern helicopters. There is now a recognized need to account for vibrations during both the analytical and experimental phases of design. Research activities in this area were both broad and varied and notable advances were made in recent years in the critical elements of the technology base needed to achieve the goal of a jet smooth ride. The purpose is to present an overview of accomplishments and current activities of govern and government-sponsored research in the area of rotorcraft vibrations and structural dynamics, focusing on NASA and Army contributions over the last decade or so. Specific topics addressed include: airframe finite-element modeling for static and dynamic analyses, analysis of coupled rotor-airframe vibrations, optimization of airframes subject to vibration constraints, active and passive control of vibrations in both the rotating and fixed systems, and integration of testing and analysis in such guises as modal analysis, system identification, structural modification, and vibratory loads measurement.

Kvaternik, Raymond G.↗

NASA NTRS2012

Sensor-Only System Identification for Structural Health Monitoring of Advanced Aircraft

Environmental conditions, cyclic loading, and aging contribute to structural wear and degradation, and thus potentially catastrophic events. The challenge of health monitoring technology is to determine incipient changes accurately and efficiently. This project addresses this challenge by developing health monitoring techniques that depend only on sensor measurements. Since actively controlled excitation is not needed, sensor-to-sensor identification (S2SID) provides an in-flight diagnostic tool that exploits ambient excitation to provide advance warning of significant changes. S2SID can subsequently be followed up by ground testing to localize and quantify structural changes. The conceptual foundation of S2SID is the notion of a pseudo-transfer function, where one sensor is viewed as the pseudo-input and another is viewed as the pseudo-output, is approach is less restrictive than transmissibility identification and operational modal analysis since no assumption is made about the locations of the sensors relative to the excitation.

Kukreja, Sunil L.↗

NASA NTRS2001

System Identification of a Vortex Lattice Aerodynamic Model

The state-space presentation of an aerodynamic vortex model is considered from a classical and system identification perspective. Using an aerodynamic vortex model as a numerical simulator of a wing tunnel experiment, both full state and limited state data or measurements are considered. Two possible approaches for system identification are presented and modal controllability and observability are also considered. The theory then is applied to the system identification of a flow over an aerodynamic delta wing and typical results are presented.

Juang, Jer-Nan↗

NASA NTRS1990

Identification and control of a flexible beam using modal domain sensor

The use of a distributed-effect, modal domain optical fiber sensor (MD sensor) as a component in an active control system to suppress vibrations in a flexible beam is discussed. The sensor model is integrated into the model for a flexible structure. Based on this system model, a control system with a dynamic compensator is designed to add damping to the low order modes of the flexible structure. To verify the modeling procedure, a cantilevered beam was instrumental with a piezoelectric actuator and an MD sensor. It is shown that experimental responses closely match simulated responses for both open loop and closed loop tests.

Cox, David E.↗

NASA NTRS1987

State-space formulation of multi-shaker modal analysis

As modal testing techniques have improved in recent years, the demands placed on the accuracy of modal test results have increased. This paper describes a new multi-input, multi-output modal parameter estimation algorithm suitable for the identification of reduced-order models of structures. The method described is a frequency-domain method based on excitation and response spectra. The principal features of the algorithm are: (1) applicability to general linear, time-invariant systems, (2) direct use of multiple input and multiple response data, (3) identification of reduced-order models with minimum user interaction through the use of two automatic model-reduction techniques, (4) identification of a consistent set of modal parameters through the use of numerically stable least-squares techniques, and (5) complete user documentation.

Craig, Roy R., Jr.↗

NASA NTRS2017

GOES-R Active Vibration Damping Controller Design, Implementation, and On-Orbit Performance

GOES-R series spacecraft feature a number of flexible appendages with modal frequencies below 3.0 Hz which, if excited by spacecraft disturbances, can be sources of undesirable jitter perturbing spacecraft pointing. In order to meet GOES-R pointing stability requirements, the spacecraft flight software implements an Active Vibration Damping (AVD) rate control law which acts in parallel with the nadir point attitude control law. The AVD controller commands spacecraft reaction wheel actuators based upon Inertial Measurement Unit (IMU) inputs to provide additional damping for spacecraft structural modes below 3.0 Hz which vary with solar wing angle. A GOES-R spacecraft dynamics and attitude control system identified model is constructed from pseudo-random reaction wheel torque commands and IMU angular rate response measurements occurring over a single orbit during spacecraft post-deployment activities. The identified Fourier model is computed on the ground, uplinked to the spacecraft flight computer, and the AVD controller filter coefficients are periodically computed on-board from the Fourier model. Consequently, the AVD controller formulation is based not upon pre-launch simulation model estimates but upon on-orbit nadir point attitude control and time-varying spacecraft dynamics. GOES-R high-fidelity time domain simulation results herein demonstrate the accuracy of the AVD identified Fourier model relative to the pre-launch spacecraft dynamics and control truth model. The AVD controller on-board the GOES-16 spacecraft achieves more than a ten-fold increase in structural mode damping of the fundamental solar wing mode while maintaining controller stability margins and ensuring that the nadir point attitude control bandwidth does not fall below 0.02 Hz. On-orbit GOES-16 spacecraft appendage modal frequencies and damping ratios are quantified based upon the AVD system identification, and the increase in modal damping provided by the AVD controller for each structural mode is presented. The GOES-16 spacecraft AVD controller frequency domain stability margins and nadir point attitude control bandwidth are presented along with on-orbit time domain disturbance response performance.

Active Vibration Damping↗

NASA NTRS1991

Search-based model identification of smart-structure damage

This paper describes the use of a combined model and parameter identification approach, based on modal analysis and artificial intelligence (AI) techniques, for identifying damage or flaws in a rotating truss structure incorporating embedded piezoceramic sensors. This smart structure example is representative of a class of structures commonly found in aerospace systems and next generation space structures. Artificial intelligence techniques of classification, heuristic search, and an object-oriented knowledge base are used in an AI-based model identification approach. A finite model space is classified into a search tree, over which a variant of best-first search is used to identify the model whose stored response most closely matches that of the input. Newly-encountered models can be incorporated into the model space. This adaptativeness demonstrates the potential for learning control. Following this output-error model identification, numerical parameter identification is used to further refine the identified model. Given the rotating truss example in this paper, noisy data corresponding to various damage configurations are input to both this approach and a conventional parameter identification method. The combination of the AI-based model identification with parameter identification is shown to lead to smaller parameter corrections than required by the use of parameter identification alone.

Glass, B. J.↗

NASA NTRS1992

New time-domain technique for flutter boundary identification

A new methodology for flutter boundary identification in the time domain is presented. This technique is based on a single-input single-output deterministic ARMA model and an on-line parameter estimation procedure. It is capable of simultaneous identification of the aeroelastic modal parameters as well as the static offset term which represents the static deformation or state of the aeroelastic system. The capabilities of the method are illustrated by applying it to several examples, such as: damped free oscillations, a two degree of freedom NACA 64A010 airfoil in transonic flight, and a cantilevered rectangular wing in subsonic flow. Numerical implementations of the new methodology developed in this study demonstrates that it is a cost effective time-domain technique for flutter boundary identification.

Pak, Chan-Gi↗

NASA NTRS1987

An overview of controls research on the NASA Langley Research Center grid

The NASA Langley Research Center has assembled a flexible grid on which control systems research can be accomplished on a two-dimensional structure that has many physically distributed sensors and actuators. The grid is a rectangular planar structure that is suspended by two cables attached to one edge so that out of plane vibrations are normal to gravity. There are six torque wheel actuators mounted to it so that torque is produced in the grid plane. Also, there are six rate gyros mounted to sense angular motion in the grid plane and eight accelerometers that measure linear acceleration normal to the grid plane. All components can be relocated to meet specific control system test requirements. Digital, analog, and hybrid control systems capability is provided in the apparatus. To date, research on this grid has been conducted in the areas of system and parameter identification, model estimation, distributed modal control, hierarchical adaptive control, and advanced redundancy management algorithms. The presentation overviews each technique and presents the most significant results generated for each area.

Montgomery, Raymond C.↗

NASA NTRS1989

Influence of rubbing on rotor dynamics, part 1

The results of analytical and experimental research on rotor-to-stationary element rubbing in rotating machines are presented. A characterization of physical phenomena associated with rubbing, as well as a literature survey on the subject of rub is given. The experimental results were obtained from two rubbing rotor rigs: one, which dynamically simulates the space shuttle main engine high pressure fuel turbopump (HPFTP), and the second one, much simpler, a two-mode rotor rig, designed for more generic studies on rotor-to-stator rubbing. Two areas were studied: generic rotor-to-stator rub-related dynamic phenomena affecting rotating machine behavior and applications to the space shuttle HPFTP. An outline of application of dynamic stiffness methodology for identification of rotor/bearing system modal parameters is given. The mathematical model of rotor/bearing/seal system under rub condition is given. The computer program was developed to calculate rotor responses. Compared with experimental results the computed results prove an adequacy of the model.

Muszynska, Agnes↗

NASA NTRS1993

Optimization for efficient structure-control systems

The efficiency of a structure-control system is a nondimensional parameter which indicates the fraction of the total control power expended usefully in controlling a finite-dimensional system. The balance of control power is wasted on the truncated dynamics serving no useful purpose towards the control objectives. Recently, it has been demonstrated that the concept of efficiency can be used to address a number of control issues encountered in the control of dynamic systems such as the spillover effects, selection of a good input configuration and obtaining reduced order control models. Reference (1) introduced the concept and presented analyses of several Linear Quadratic Regulator designs on the basis of their efficiencies. Encouraged by the results of Ref. (1), Ref. (2) introduces an efficiency modal analysis of a structure-control system which gives an internal characterization of the controller design and establishes the link between the control design and the initial disturbances to affect efficient structure-control system designs. The efficiency modal analysis leads to identification of principal controller directions (or controller modes) distinct from the structural natural modes. Thus ultimately, many issues of the structure-control system revolve around the idea of insuring compatibility of the structural modes and the controller modes with each other, the better the match the higher the efficiency. A key feature in controlling a reduced order model of a high dimensional (or infinity-dimensional distributed parameter system) structural dynamic system must be to achieve high efficiency of the control system while satisfying the control objectives and/or constraints. Formally, this can be achieved by designing the control system and structural parameters simultaneously within an optimization framework. The subject of this paper is to present such a design procedure.

Oz, Hayrani↗

NASA NTRS1979

The Apollo 17 drill core - Petrologic systematics and the identification of a possible Tycho component

Modal data support a five-unit stratigraphy for the Apollo 17 drill core. The upper unit E (0-22 cm depth) is marked by high content of fused soil, brown glass, and mare basalt fragments. This unit corresponds with a portion of the core excavated and refilled within the last 2 m.y. The underlying unit D (22071 cm depth) has a low abundance of fused soil (i.e., low maturity) and is rich in coarse (less than 200 microns) mare fragments. A large section of the core, unit C (71-224 cm depth), is finer-grained, more mature (richer in agglutinates), more feldspathic and has more highland lithic, mineral and glass fragments than unit D. The next underlying unit, B (224-256 cm depth), has yellow/colorless KREEP glasses with a high Si, low-alkali composition unlike the common Apollo 15 or Apollo 17 KREEP series. The petrologic (fused soil) and Is/FeO maturity of this layer is also lower than the units above and below. The deepest unit, A (256-284 cm depth), is marked by its relatively higher maturity and lower yellow/colorless KREEP glass content. The most prominent petrographic/stratigraphic indicators are the pyroxene-rich immature mare unit D and the abundance of KREEP glass in unit B. This KREEP glass is distinctive petrographically and compositionally, and is probably exotic to the Apollo 17 site. It is suggested here that the KREEP glass in unit B is derived from Tycho, which implies widespread distribution of KREEP on the lunar nearside.

Vaniman, D. T.↗

NASA NTRS1989

System identification test using active members

A modal test using active members as the excitation source has been performed on the Precision Truss. Using the step sine testing technique, the frequency response functions are obtained and the modal parameters are extracted by the curve-fitting method. Total of 10 global modes and 3 local modes are obtained. The results are compared with those obtained by the conventional external excitation test.

Chen, Jay-Chung↗

NASA NTRS1990

Identification and control for a manipulator with two flexible links

The authors investigate the effectiveness of an online identification scheme for tracking the modal frequencies of a two-link flexible mechanism executing large-angle movements and carrying an unknown payload. A decentralized, gain-scheduled, adaptive control scheme is employed in conjunction with the identification scheme in order to illustrate the feasibility of online controller adjustment for endpoint position control in terms of vibration suppression after large-angle movements. Motivation for adopting the autoregressive-moving-average-model perspective is based on the convenient representation for online controller tuning and on the assumption that flexibility dynamics, for small deflections after a nonlinear large-angle motion, exhibit linear behavior. Experimental results are presented for a two-link planar mechanism in which both links are very flexible.

Yurkovich, Stephen↗