Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Ion velocity effect governs damage annealing process in defective KTaO 3

Effects of electronic to nuclear energy losses (S e /S n ) ratio on damage evolution in defective KTaO 3 have been investigated by irradiating pre-damaged single crystal KTaO 3 with intermediate energy O ions (6 MeV, 8 MeV and 12 MeV) at 300 K. By exploring these processes in pre-damaged KTaO 3 containing a fractional disorder level of 0.35, the results demonstrate the occurrence of a precursory stage of damage production before the onset of damage annealing process in defective KTaO 3 that decreases with O ion energy. The observed ionization-induced annealing process by ion channeling analysis has been further mirrored by high resolution transmission electron microscopy analysis. In addition, the reduction of disorder level is accompanied by the broadening of the disorder profiles to greater depth with increasing ion fluence, and enhanced migration is observed with decreasing O ion energy. Since S e (~3.0 keV nm –1 ) is nearly constant for all 3 ion energies across the pre-damaged depth, the difference in behavior is due to the so-called 'velocity effect': the lower ion velocity below the Bragg peak yields a confined spread of the electron cascade and hence an increased energy deposition density. Here, the inelastic thermal spike calculation has further confirmed the existence of a velocity effect, not previously reported in KTaO 3 or very scarcely reported in other materials for which the existence of ionization-induced annealing has been reported. In other words, understanding of ionization-induced annealing has been advanced by pointing out that ion velocity effect governs the healing of pre-existing defects, which may have significant implication for the creation of new functionalities in KTaO 3 through atomic-level control of microstructural modifications, but may not be limited to KTaO 3 .

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Exploring the Storage Mechanism of Alkali Ions in Non-Graphitic Hard Carbon Anodes

This study aims to develop high-capacity hard carbon anode materials for alkali-ion batteries by controlling the microstructures of non-graphitic hard carbon through an annealing protocol and investigating the effects on the alkali-ion storage mechanisms using physical, chemical, and electrochemical analytical techniques. The hard carbon materials were synthesized at temperatures ranging from 900 °C to 1600 °C. Those synthesized at 1100 °C with high surface area and abundant defects exhibited the highest reversible capacity in Li- and K-ion systems, with the storage dominated by surface-adsorption mechanisms. In contrast, the hard carbon compounds prepared at 1400 °C with numerous curve-featured pores delivered the highest reversible capacity in the Na-ion system, indicating that these pores are the preferred Na-ion storage sites, particularly in low-voltage plateau regions. This study provides a comprehensive understanding of the relationship between microstructures and alkali-ion storage mechanisms in non-graphitic hard carbon and highlights the importance of tailoring the microstructures of hard carbon to achieve high specific capacity for the desired alkali-ion species.

25 ENERGY STORAGE↗
DOE OSTI2025

AdditiveFOAM: A Continuum Multiphysics Code for Additive Manufacturing

AdditiveFOAM is a computational framework that simulates transport phenomena in Additive Manufacturing (AM) processes. It is built on OpenFOAM (Weller et al., 1998), the leading free, open-source software package for computational fluid dynamics (CFD). OpenFOAM offers an extensible platform for solving complex multiphysics problems using state-of-the-art finite volume methods. AdditiveFOAM leverages these capabilities to develop specialized tools aimed at addressing challenges in AM processing. Metal additive manufacturing, also known as metal 3D printing, is an advanced manufacturing technique that creates physical parts from a three-dimensional (3D) digital model by melting metal powder or wire feedstock. A significant area of research in metal AM focuses on process planning to mitigate anomalous features during printing that are deleterious to part performance (e.g., porosity and cracking), as well as controlling localized microstructure and material properties. Given the high costs and substantial time requirements associated with experimental methods for qualifying new materials and processes, there is a compelling incentive for researchers to utilize advanced computational simulations. In this context, AdditiveFOAM offers a simulation framework to better understand undesirable features in printing, thereby enhancing process planning and reducing the reliance on labor-intensive experimental campaigns.

Coleman, John [Oak Ridge National Laboratory (ORNL↗
DOE OSTI2022

MODELLING OF ADDITIVE MANUFACTURING – COMPRESSION MOLDING PROCESS USING COMPUTATIONAL FLUID DYNAMICS

A computational fluid dynamics model has been developed to predict the behavior of a printed strands during a novel material extrusion additive manufacturing and compression molding process. While the traditional additive manufacturing process enables control over the fiber orientation within the part, it would also result in high void content. On the other hand, compression molding produces parts with low porosity levels at rapid processing cycle time but lacks control over the microstructure. The novel additive manufacturing – compression molding (AM-CM) integrating both these processes offers control over both the microstructure and porosity to manufacturing high performance composite parts. The numerical model developed here enables to analyze the effect of processing parameters on the behaviour of printed layer that is subsequently compressed and to determine the optimal printing parameters for high-performance composite part design.

Seta, Berin↗
DOE OSTI2020

Engineering the Microstructure and Morphology of Explosive Films via Control of Interfacial Energy

Physical vapor deposition of organic explosives enables growth of polycrystalline films with a unique microstructure and morphology compared to the bulk material. This study demonstrates the ability to control crystal orientation and porosity in pentaerythritol tetranitrate films by varying the interfacial energy between the substrate and the vapor-deposited explosive. Additionally, variation in density, porosity, surface roughness, and optical properties is achieved in the explosive film, with significant implications for initiation sensitivity and detonation performance of the explosive material. Various surface science techniques, including angle-resolved X-ray photoelectron spectroscopy and multiliquid contact angle analysis, are utilized to characterize interfacial characteristics between the substrate and explosive film. Optical microscopy and scanning electron microscopy of pentaerythritol tetranitrate surfaces and fracture cross sections illustrate the difference in morphology evolution and the microstructure achieved through surface energy modification. X-ray diffraction studies with the Tilt-A-Whirl three-dimensional pole figure rendering and texture analysis software suite reveal that high surface energy substrates result in a preferred (110) out-of-plane orientation of pentaerythritol tetranitrate crystallites and denser films. Low surface energy substrates create more randomly textured pentaerythritol tetranitrate and lead to nanoscale porosity and lower density films. This work furthers the scientific basis for interfacial engineering of polycrystalline organic explosive films through control of surface energy, enabling future study of dynamic and reactive detonative phenomena at the microscale. Results of this study also have potential applications to active pharmaceutical ingredients, stimuli-responsive polymer films, organic thin film transistors, and other areas.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Dynamic Beam Shape Sensing and Control in an Open Architecture Metal AM System for Microstructure Manipulation

Most commercially available metal additive manufacturing (AM) systems are closed-architecture, meaning that the system manufacturer limits the ability of the user to directly control the process conditions and can modify the specified inputs using proprietary methods. Unfortunately, this approach severely limits or confounds the ability for users to perform research on fundamental aspects of additive manufacturing. ARCTOS Technology Solutions (ARCTOS) produces an open-architecture laser powder bed fusion (PBF) additive manufacturing system that allows the user to fully control all aspects of the process control and monitoring. The purpose of this project is to help develop beam shaping capabilities and controls within the ARCTOS open-architecture system for control of microstructure evolution during metal AM.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Defect formation and microstructure tuning via proton irradiation to control electrochemical and phase reversibility in layered battery materials

The reversibility of phase transformation influences the functionality of electrode materials in batteries. In many battery materials, nanosized grains favor phase reversibility but at the cost of cyclability due to aggravated side reactions with the electrolyte. Here, in this study, we present a novel approach to enhance the phase transformation reversibility of layered oxide cathodes, exemplified by Na 2/3 Fe 1/2 Mn 1/2 O 2 through proton irradiation. In addition to forming defects, proton irradiation at sufficiently high doses can subdivide single grains into multiple nanodomains without physically rupturing them. Hence, the single grains of the material assume a pseudo-secondary particle nature without reducing the overall grain size. Preserving the grain size is advantageous, as it reduces side reactions, which is not possible with conventional grain size reduction methods. While chemical transformations and defect formation induced through proton irradiation can influence the stability of battery materials, it is expected that structural reorganization due to cycling-induced phase transformation will be contained within these nanodomains. Such confinement of phase transformation is potentially responsible for enhancing the reversibility of layered oxide materials in our study. Thus, our study suggests that grain subdivision could become an effective microstructure tuning strategy for managing electrochemical cycling-induced phase changes in battery electrodes.

25 ENERGY STORAGE↗
DOE OSTI2022

High-Energy Solid-State Lithium Batteries with Organic Cathode Materials (Final Report)

Organic materials made from abundant elements via low-energy processes are emerging as sustainable and low-cost alternatives to transition metal oxides as the electrode materials for high- energy batteries in the wake of supply chain and environmental issues associated with critical materials during the transition to clean energy. Organic insertion materials (OIMs) offer material- level energy comparable to transition metal oxides, but they have durability difficulties owing to dissolving in common liquid electrolytes. Combining ceramic-based solid electrolytes with organic electrode materials is one intriguing solution. The goal of this project is to design and synthesize high-energy OIMs, to understand the chemical dynamics and mechanical properties at the OIM-sulfide interface during electrochemical cycling, and to develop methods for constructing the optimum cathode microstructure, which will lead to improved electrochemical performance. The project team has accomplished the following over the last four years: (a) demonstrating that the mechanical softness of organic electrode materials is uniquely beneficial in suppressing crack formation at the electrode-electrolyte interface during cell operation; (b) understanding the interaction between cathode microstructure and the mechanical properties of individual components; and (c) establishing predictive control of cathode microstructure by tuning the mechanical properties of solid electrolytes and OIMs; (d) determining the chemical combability of sulfide electrolyte with high-energy OIMs and finally (f) laying out a road map toward a specific energy of 500 Wh kg -1 for solid-state lithium batteries. 14 publications resulted from this project.

25 ENERGY STORAGE↗
DOE OSTI2021

Observation of Stepwise Ultrafast Crystallization Kinetics of Donor–Acceptor Conjugated Polymers and Correlation with Field Effect Mobility

The semicrystalline microstructures of donor-acceptor conjugated polymers strongly impact their optoelectronic properties. The control of the microstructure relies on the understandings of the crystallization processes in these polymers, from packing structures to crystallization kinetics. How fast these conjugated polymer chains crystallize and how their chemical structures and pre-existing microstructure history influence their crystallization have so far remained unclear, due to the fast crystallization rate caused by chain rigid structures and strong interactions. Here, ultrafast scanning calorimetry (FSC) is employed to reveal the crystallization behaviors of high perform- ance diketopyrrolopyrrole (DPP)-based conjugated polymers with scanning rates up to 500 000 K/s. Through elaborately designed nonisothermal and isothermal crystallization studies, we probed the fast crystallization kinetics and extracted the two-step crystallization process of these polymers quantitatively. We found that both the rigidity of the chain backbones and the preinduced crystalline microstructures can influence the crystallization rate over an order of magnitude at the same degree of undercooling. We further demonstrated the manipulated crystallization kinetics in the DPP-based polymer films with different amounts of preinduced crystallites and correlate it to the polymers’ charge transport mobility.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High Performance Computing to Quantify the Evolution of Microscopic Concentration Gradients During Flash Processing

During the Flash process, the cross section of a plain-carbon or a low-alloy steel is austenitized through rapid heating and transformed on rapid cooling to a predominantly martensite + bainite structure with small amounts of retained austenite. Unlike conventional heat treating, homogeneity is intentionally avoided during Flash processing of steels. The Flash process assembly consists of a pair of rolls that transfer the steel sheets through the heating and cooling stage of the thermal cycle. The initial microstructure of the steel consists of ferrite (body-centered cubic iron) + carbide ((Fe,X)mCn) mixture. The heating rate through the peak temperature is a function of temperature and reaches a peak of about 300-400°C/s and the cooling rate has a maximum value of 3,000-4,000°C/s. The on-heating phase transformations include carbide dissolution, austenite (face-centered cubic iron) nucleation and growth, and diffusion of carbon and other substitutional elements in the steel. The on-cooling phase transformations include formation of martensite (body-centered tetragonal phase containing supersaturated solute) and bainite (ferrite plates with or without fine carbides). In this project, the focus is on Fe-C-Cr steels that are currently Flash processed for armor applications. The modeling effort proposed here will help optimize the Flash thermal cycle for these low alloy steels to achieve the target performance, which is an ongoing effort at SFP Works. A significant feature of Flash processed Fe-C-Cr steels is the presence of scatter in the through-thickness in the sheet. The variability in hardness results from a variability in the bainite + martensite microstructure that is sensitive to the local chemical concentration of C and Cr. Such a chemical inhomogeneity is intentionally obtained in the Flash process. Although such a microstructural gradient is presumably responsible for the exceptional properties of the Flash processed steel, it is very important to quantify the gradients as a function of Flash variabilities in processing parameters and the input microstructure. Understanding the mechanistic pathway that leads to microstructural gradients could be ground-breaking and instrumental for achieving better process control and optimized microstructural state to meet application-specific strength-ductility requirements. Since the final microstructure depends on setting up precise solute concentration gradients through a rapid heating process, and transforming these regions into various phases, it is important to understand how small changes in steel chemistry, input microstructure (carbide size and distribution), and process variables (Flash thermal cycle) will impact the solute concentration gradients.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Tailoring Piezoelectricity of 3D Printing PVDF-MoS 2 Nanocomposite via In Situ Induced Shear Stress

3D printing of unique structures with tunable properties offers significant advantages in the fabrication of complex and customized electronic devices. Here, this study introduces a process-microstructure–property-guided manufacturing route to fabricate PVDF-2D MoS 2 piezoelectric nanocomposites with tunable piezoelectric properties without having a postprocess. We control PVDF’s microstructure through direct ink writing (DIW) 3D printing while tuning PVDF-MoS 2 interfacial strain by controlling rheology and 3D printing parameters, such as nozzle size and printing speed. Our approach demonstrates tunable piezoelectricity in PVDF-MoS 2 , achieving a 15-fold increase in the piezoelectric coefficient (d 33 ) at a printing-induced shear stress of 6685 Pa. This enhancement arises from the electrostatic interactions between PVDF and MoS 2 and the filler distribution and alignment caused by the in situ shear stress in 3D printing, as confirmed by XPS and Raman mapping analyses. Our findings advance the understanding of piezoelectric mechanisms in PVDF-based nanocomposites, laying the foundation for 3D printing of piezoelectric sensors in wearable device applications with enhanced performance and customization capabilities.

2D MoS2↗
DOE OSTI2025

Manufacturing Li 2 TiO 3 -based tritium breeder materials by volume-controlled spark plasma sintering with an optimized microstructure

Multifunctional ceramic breeder materials are highly desirable for the deuterium-tritium fusion to achieve high efficiency in breeding tritium through neutron irradiation of lithium-containing blankets. Li 2 TiO 3 displays unique attributes as a potential ceramic breeder material. An optimized microstructure with three-dimensional interconnected pore structure is required for rapid transport of the tritium for effective fuel cycle, which however enviably results in the degradation of the thermal-mechanical properties of the breeding materials. In this work, nanocrystalline porous Li 2 TiO 3 ceramic pellets with controlled porosities of 14% and 20% are manufactured by volume-controlled spark plasma sintering. An optimized 3D interconnected pore structure is achieved consisting of both micro-sized pores and nano-sized pores embedded in nanocrystalline matrix, which could be beneficial to facilitate easy removal of bred T and He. Further, the 3D interconnected porous structure is well maintained upon isothermal annealing of the SPS-fabricated pellets at relevant operation temperature of the solid breeding materials. Single-phasic porous pellets also display enhanced thermal-mechanical properties, superior to current state-of-the-art materials which establish their potential as a promising tritium breeder material for nuclear fusion applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Limiting Retained Austenite Decomposition in Quenched and Tempered Steels: Influences of Rapid Tempering and Silicon

Tempering reactions are critical to microstructure and property control in martensitic steels. Here, retained austenite decomposition and cementite precipitation are monitored using Mössbauer spectroscopy in 4340 and 300-M steel under conventional and rapid tempering conditions. Tempering times are compared at a constant tempered hardness by increasing tempering temperatures associated with short time conditions to achieve equivalent matrix softening to that of longer tempering times. Time-temperature combinations that provide equivalent tempered hardness generated microstructures with similar dislocation densities and cementite precipitation fractions; these mechanisms are controlled by self-diffusion. However, systematic differences in retained austenite content were observed at a given degree of softening, where shorter tempering times exhibited higher levels of retained austenite compared to more conventional conditions. At low temperatures, the differences in retained austenite preservation between explored time-temperature conditions are attributed to corresponding differences in carbon diffusion distance (in austenite), the controlling diffusional process of retained austenite decomposition. At higher temperatures, retained austenite decomposition exhibits C-curve kinetic behavior in 4340. Thus, reduced thermodynamic driving force for cementite and ferrite formation at higher temperature is believed to play a role in restricting retained austenite decomposition within some short-time, high temperature tempering regimes. The addition of silicon pushes cementite precipitation and retained austenite decomposition to higher temperatures, although retained austenite decomposition is suppressed to a greater extent than cementite precipitation. Potential is illustrated for coupling rapid tempering with silicon alloying to produce appreciably tempered martensite (~490 HV) with relatively less retained austenite decomposition compared to conventional tempering conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Chain rigidity controlled aggregation ability and solid-state microstructures for efficient stretchable conjugated polymer films

Stretchable conjugated polymer films with good electrical performance under mechanical deformation are highly desirable for soft electronics. However, the mechanical and electrical properties of these films, particularly in conjugated polymer:elastomer blends, are not fully understood at molecular level. Here, this study explores the relationships among molecular structure, aggregation ability, film microstructure, and the electrical/mechanical properties of three diketopyrrolopyrrole-based conjugated polymers (P1, P2, P3) with decreasing backbone rigidity and their corresponding polymer:elastomer blends. The most flexible polymer P3 shows strong aggregation, which forms highly crystalline fibers to produce fragile neat film and produces large isolated crystallites restricting charge transport in blend film. As chain rigidity increases, the P1 and P2 polymers show weaker aggregation, and produce smaller crystallites in neat films with enhanced ductility. P1 and P2 based blend films display nanocrystallites polymer networks with dispersed elastomer domains. As a result, we achieved near-constant charge mobility before and after stretching under 50 % strain for P2-based blend films with well-controlled pathways for both charge transport and energy dissipation. This study demonstrates the critical role of backbone rigidity in regulating the properties of stretchable conjugated polymer films, paving the way for more reliable and deformable materials in soft electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear-based deformation processing of age-hardened aluminum alloy for single-step sheet production

Shear-based deformation processing by hybrid cutting-extrusion and free machining are used to make continuous strip, of thickness up to one millimeter, from low-workability AA6013-T6 in a single deformation step. The intense shear can impose effective strains as large as 2 in the strip without pre-heating of the workpiece. The creation of strip in a single step is facilitated by three factors inherent to the cutting deformation zone: highly confined shear deformation, in situ plastic deformation-induced heating and high hydrostatic pressure. The hybrid cutting-extrusion, which employs a second die located across from the primary cutting tool to constrain the chip geometry, is found to produce strip with smooth surfaces (S a < 0.4 μm) that is similar to cold-rolled strip. The strips show an elongated grain microstructure that is inclined to the strip surfaces – a shear texture – that is quite different from rolled sheet. Furthermore, this shear texture (inclination) angle is determined by the deformation path. Through control of the deformation parameters such as strain and temperature, a range of microstructures and strengths could be achieved in the strip. When the cutting-based deformation was done at room temperature, without workpiece pre-heating, the starting T6 material was further strengthened by as much as 30% in a single step. In elevated-temperature cutting-extrusion, dynamic recrystallization was observed, resulting in a refined grain size in the strip. Implications for deformation processing of age-hardenable Al alloys into sheet form, and microstructure control therein, are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Considering interplay between multiple physical phenomena to elucidate single crystal-like texture, phase transformations, and mechanical behavior of directed energy deposited SS316L

A widespread implementation of large scale additive manufacturing (AM) processes, such as wire arc-directed energy deposition (WA-DED) AM can transform the current manufacturing supply chain networks. Naturally, such implementation requires control of the microstructural attributes, such as texture and phase evolution in the processed alloys. Currently, the texture evolution in fusion-based AM (F-BAM) processes is majorly rationalized by the phenomena occurring only during solidification. However, such rationalization is insufficient for understanding the evolution of primary and secondary crystallographic orientations, and consequently, fails to offer a comprehensive understanding and control of overall texture in F-BAM processed alloys. To this end, we report a single crystal (SX)-like texture in WA-DED processed SS316L for the first time. Furthermore, we assess the physical phenomena that may lead to such unique microstructural evolution during WA-DED AM. Subsequently, using microstructural characterization spanning the build height and thermomechanical simulations we investigate the effect of competitive growth and epitaxial growth occurring during solidification and thermally induced plastic deformation occurring post solidification on the overall texture of WA-DED processed SS316L. A spatial variation in solidification pathway is also established and correlated with variation in undercoolings across the build. Tensile tests revealed a strong orientation dependence of deformation mechanisms with over 110% elongation to failure of specimens deformed along <011>. Such anisotropy is rationalized using Schmid's analysis of dislocation slip and deformation twinning. Importantly, overall, the mechanisms outlined in this work will facilitate an enhanced understanding and subsequent control of texture evolution, solidification behavior and mechanical behavior of WA-DED processed steels.

36 MATERIALS SCIENCE↗