SEARCH · Engineering Papers

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Comparison of the Thermal Stability in Equal‐Channel‐Angular‐Pressed and High‐Pressure‐Torsion‐Processed Fe–21Cr–5Al Alloy

Nanostructured steels are expected to have enhanced irradiation tolerance and improved strength. However, they suffer from poor microstructural stability at elevated temperatures. In this study, Fe–21Cr–5Al–0.026C (wt%) Kanthal D (KD) alloy belonging to a class of (FeCrAl) alloys considered for accident‐tolerant fuel cladding in light‐water reactors is nanostructured using two severe plastic deformation techniques of equal‐channel angular pressing (ECAP) and high‐pressure torsion (HPT), and their thermal stability between 500–700 °C is studied and compared. ECAP KD is found to be thermally stable up to 500 °C, whereas HPT KD is unstable at 500 °C. Microstructural characterization reveals that ECAP KD undergoes recovery at 550 °C and recrystallization above 600 °C, while HPT KD shows continuous grain growth after annealing above 500 °C. Enhanced thermal stability of ECAP KD is from significant fraction (>50%) of low‐angle grain boundaries (GBs) (misorientation angle 2–15°) stabilizing the microstructure due to their low mobility. Small grain sizes, a high fraction (>80%) of high‐angle GBs (misorientation angle >15°) and accordingly a large amount of stored GB energy, serve as the driving force for HPT KD to undergo grain growth instead of recrystallization driven by excess stored strain energy.

Arivu, Maalavan↗

DOE OSTI2022

TEM Specimen Manufacturing to Support Analysis of IASCC Mechanisms in Irradiated Austenitic Steels – Light-Water– Relevant Materials

The present report describes the manufacturing of samples for advanced microstructure studies of mechanisms of irradiation-assisted stress corrosion cracking (IASCC) in the materials of light-water reactor (LWR) internal components. The samples were manufactured via FIB (focused ion beam milling) from 4-point-bend specimens subjected to oxidation and mechanical loading in a simulated LWR environment (primary water, PW). The corrosion tests were conducted at the University of Michigan (UM), and the tested specimens were transported to ORNL to perform FIB work. Finally, the manufactured FIB specimens were shipped back to the UM for microstructure characterization. Section 1 in the report provides a brief introduction; Section 2 describes materials, their in-service and irradiation history, and the geometry of specimens for IASCC testing. Section 3 documents typical work steps (specimen mapping) and reports the number of manufactured FIB objects. Section 4 briefly describes the preliminary results of microstructure analysis performed at the University of Michigan and highlights the key findings. The summary and conclusions section discusses future possible future steps and generalizes the obtained results, their unique character, and their importance for the nuclear industry.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2026

Additively manufactured refractory high-entropy alloys with superior radiation resistance

Refractory high-entropy alloys (RHEAs) are promising candidates for next-generation nuclear and high-temperature applications. Among many approaches to manufacture RHEAs, additive manufacturing (AM) represents the most recent and advanced metal manufacturing method which allows near-net-shape manufacturing to reduce material waste and post-processing time. However, performance of AM RHEAs under complex irradiation conditions remains largely unexplored. Here, in this study, we demonstrate for the first time the response of directed energy deposition (DED) AM quaternary RHEAs (HfTaVW, CrTaVW) subjected to sequential dual-beam ion irradiation, consisting of helium pre-implantation followed by high-dose heavy ion bombardment. Compositions of DED AM RHEAs were selected using Monte Carlo (MC) simulations based on a cluster expansion (CE) Hamiltonian parameterized by density functional theory (DFT). Post-irradiation microstructural characterization revealed that the AM RHEA maintained remarkable stability, with suppressed helium bubble growth and reduced defect accumulation compared to conventional alloys. Even at high doses (∼100 dpa), the alloy exhibited no void swelling, a low density of dislocation loops, and no evidence of severe degradation. These results highlight the intrinsic ability of AM-derived microstructures and multicomponent chemistry to synergistically mitigate irradiation effects. Our findings establish AM RHEAs as a class of materials with superior resistance to radiation damage under conditions relevant to advanced fusion and fission environments and demonstrate the importance of sequential ion beam studies in evaluating their long-term performance.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Minimizing thickness variation in monolithic U-10Mo fuel foil and Zr interlayer during hot rolling: A microstructure-based finite element method analysis

Low-enriched uranium alloyed with 10 wt. % molybdenum (U-10Mo) has been identified as a promising alternative to highly enriched uranium fuel for the United States’ high performance research reactors. The monolithic U-10Mo fuel plate consists of a metallic U-10Mo fuel foil with a 25 µm Zr interlayer and a relatively thick cladding of aluminum alloy 6061. The Zr interlayer is typically applied during the hot co-rolling process, and this process dictates the uniformity of the Zr interlayer. Thickness variation observed in the U-10Mo and Zr interlayer has been attributed to several sources: the initial grain size of the U-10Mo castings, can materials, rolling temperature, inhomogeneous molybdenum content, and porosity in the cast U-10Mo. This thickness variation limits the ability to meet the dimensional specification; thus, a better understanding of the factors causing the nonuniform thickness is needed. In this work, we used a novel, microstructure-based finite element method to model the hot rolling process to address these concerns. Grain microstructures in U-10Mo were tessellated and explicitly considered in the finite element model. Each grain was assigned a random material property to mimic the grain strength variations induced by different grain orientations. Simulations were performed using six steel can thicknesses, four grain sizes, and with or without a Zr interlayer to investigate the influences of those variables on the thickness nonuniformity. The simulation results showed that a thinner steel can and finer U-10Mo grain size reduce thickness variations in both the U-10Mo fuel foil and Zr interlayer. The direct findings from the simulations and analysis can be used to optimize the hot rolling schedule, reduce fabrication defects, and meet the dimensional specifications. The proposed microstructure-based finite element model can be also coupled with experimental microstructure characterization data, images, and models to simulate multi-pass hot rolling.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Microstructural diversity and digestion yields of select bituminous and subbituminous coals as raw material candidates for carbon fiber precursor production

Here, this work investigates the use of coals as raw materials for carbon fiber precursor production as a new alternative to coal utilization. Coal being a highly complex and heterogeneous material with different macerals and minerals complicates this task. Extensive microstructural characterization as well as preliminary digestion studies are performed on three bituminous coals (Herrin and Springfield from the Illinois Basin and the Blue Gem from the Central Appalachians) and one subbituminous coal from the Powder River Basin (Monarch), as raw material candidates. The subbituminous coal was richer in oxygen, lower in sulfur, and had a higher volatile matter yield. Microstructural investigations were performed using X-ray diffraction, X-ray/neutron computed tomography, scanning electron microscopy with energy dispersive spectroscopy, and petrology. Mild solvent extraction studies were conducted using creosote and decant oil as solvents in microreactors. The extraction yield was sensitive to temperature and time (350 to 450 °C between 30 and 120 mins.) for both creosote and decant oil digestions. While the Blue Gem coal had more desirable microstructural properties with less mineral content and cleaner macerals, it had the lowest coal conversion to quinoline soluble ‘liquid’ (of the bituminous coals). The lower coal conversion yield was hypothesized to be connected to the lack of FeS2 which could act as a catalyst when Fe is liberated from the structure under solvent extraction conditions. The Herrin and Springfield coals revealed similar microstructures and coal conversion efficiencies (higher than Blue Gem). These coals were the most promising candidates for further examination from this first approximations study. The subbituminous Monarch coal, however, was deemed less suitable due to poor coal conversion and less desirable microstructures. Additionally, the presented results with combined microstructural data from multiple length scales established a framework necessary for a first approximations study in this new coal utilization approach.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Comparison on the properties of ITZs in fly ash-based geopolymer and Portland cement concretes with equivalent flowability

Highlights: • Modelled ITZs can effectively avoid the effects caused by different factors and test locations of ITZ. • ITZ properties of PC and geopolymer concretes are compared based on equivalent flowability of binders. • Geopolymer ITZ exhibits stronger bonding than that of PC, and higher mechanical properties than geopolymer paste. • Strong ITZs in geopolymer concrete are attributed to the layer of gel-rich paste with dense microstructures. • Elastic modulus and hardness properties of ITZs in PC concrete are increased due to the CH crystals. This paper aims to compare the properties of interfacial transition zones (ITZs) in Portland cement (PC) concrete and geopolymer concrete. Portland cement and geopolymer pastes were designed with the equivalent flowability to provide similar mix and casting condition of ITZs. Two types of modelled ITZs were prepared to facilitate the nanoindentations across ITZs, microstructural characterization, and comparison on the properties of ITZs with less influential factors. The results showed that the interfacial bonding of ITZs between geopolymer matrix and aggregate is relatively stronger than the counterpart in the PC concrete. There is a high amount of crystalline hydration products in the ITZs of PC concrete, but a layer gel-rich paste with denser microstructures in the ITZs of geopolymer concrete. Additionally, the interface morphology and nanoindentation analysis indicate that the property of ITZs in the modelled geopolymer concrete is not poorer than that of the corresponding geopolymer paste.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Exploring the Microstructure-Property Relationship of Mg-Al-Mn alloys enhanced via Friction Stir Processing

Friction Stir Processing (FSP) is a solid-state thermomechanical processing technique that enables local grain refinement, densification, and homogenization of microstructure in metallic components. Here, FSP is applied to thin sheets of high-pressure die cast AM60 to address the porosity and heterogeneities inherent to the casting process. In this work, microstructure characterization is correlated to improvements in the static mechanical properties of the Mg-Al-Mn alloy system at various FSP processing conditions. Notably, there is a significant increase in the ductility and ultimate tensile stress of system following FSP. The dominant deformation mechanisms for the as-cast material and the FSP material are investigated. Finally, the fatigue life improvement is correlated to microstructure modifications that may lead to distinct behavior in crack initiation and crack propagation for the as-cast and FSP material.

Garcia, David↗

DOE OSTI2022

Transformation and twinning induced plasticity in metastable Ti-Mo alloys under high strain rate deformation

The development of metastable titanium (Ti) alloys provides an unprecedented opportunity to expand their use in plasticity and damage critical applications like protective structures. However, such applications require knowledge of quasi-static to dynamic mechanical behavior, which is currently lacking. Here we perform in-situ, ultrafast synchrotron x-ray diffraction during high strain rate (Kolsky) pressure bar testing in tension and post-mortem electron microscopy to study TRansformation Induced Plasticity (TRIP) and TWinning Induced Plasticity (TWIP) in metastable Ti-Mo alloys. Two alloys, namely Ti-12Mo and Ti-15Mo (wt.%), were selected for study having different β -phase chemical stabilities. TWIP was observed in both Ti-12Mo and Ti-15Mo by in-situ synchrotron diffraction during high strain rate testing. Post-mortem microstructural characterization also revealed the presence of TRIP in Ti-12Mo. TWIP in Ti-15Mo was found to under-perform in terms of total elongation compared to TRIP/TWIP in Ti-12Mo. Ti-12Mo exhibited an average elongation of 17% compared to only 12% for Ti-15Mo with deformation at 1000 s -1 . In conclusion, TRIP resulted in significantly finer microstructure evolution and alleviated local strain accumulations in Ti-12Mo, suggesting TRIP can be used to tune available strength/ductility combinations in metastable Ti alloys under high strain rate deformation conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Geomechanical characterization of Rock Valley carbonates

In Rock Valley, Nevada, the USA, past earthquake sequences and shallow faulting in Paleozoic carbonates remain poorly understood. Carbonates are typically more ductile rocks that do not experience large stress drops or fracture coalescence, which contradicts previous observations in the region. As part of the Source Physics Experiment, an effort has been made to experimentally characterize the petrophysical and geomechanical properties of carbonates from Rock Valley. Well core and outcrop samples were used to determine the difference between shallow-buried Tertiary limestones and deeply buried Paleozoic limestones and dolostones. The carbonates possessed porosities between 3 and 9%, with V P and V S in the Tertiary carbonates around 2700 and 1800 m/s, respectively, and 6000 and 3100 m/s, respectively, in the Paleozoic carbonates. Microstructural characterization revealed that the Paleozoic carbonates contained significantly more pre-existing damage and alteration than the Tertiary carbonates, though the deformation varies from localized to diffuse. Unconfined Brazilian tests and triaxial tests with confining pressures between 0 and 50 MPa showed that, although samples all experienced failure, the dolostones typically failed at greater stresses and possessed greater E/ν ratios than the limestones. Furthermore, the Hoek–Brown failure criterion was used to construct failure envelopes with the compressive and tensile failure tests. Velocity, density, and porosity measurements were used to construct a hypothetical velocity-depth profile and compare the results with the theoretical petrophysical measurements. Using brittleness analysis, the likely failure conditions were determined to be low-porosity dolomitic rock for fault nucleation in the Paleozoic basement.

Brittleness↗

DOE OSTI2024

Insight into the interfacial microstructure and chemistry of hot isostatically pressed AA6061-AA6061 bonds for U-10Mo fuel cladding application

Here, in the present study, hot isostatic pressing (HIP) bonding was carried out using AA6061-AA6061 plates for U-10Mo monolithic fuel cladding application. HIP was performed at 560°C with an applied isostatic pressure of 103 MPa for 90 min. Interfacial microstructure characterizations were performed using scanning electron microscopy (SEM) combined with electron backscatter diffraction (EBSD) to quantify precipitate fractions and study recrystallization, grain growth, and orientation relationships across the interface. EBSD results confirmed that no interfacial grain growth occurred during the HIP process. Transmission electron microscopy (TEM) was also employed to quantify composition and identify phases of various precipitates and an oxide layer that formed at the interface during HIP bonding. Microstructural analyses revealed the formation of a large fraction of Mg 2 Si precipitate and a ~50 nm thick Mg-oxide layer at the interface. Further TEM analysis confirmed that the oxide layer was not continuous, and Mg 2 Al 2 O 5 oxide particles with an average size of 18 nm were present in the oxide layer. Finite element modeling analysis was performed to study the stress distribution at the interface during HIP processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Effect of nitriding on mechanical and microstructural properties of Direct Metal Laser Sintered 17-4PH stainless steel

In this work, the effect of the nitriding process on microstructure and mechanical properties of additively manufactured (AM) 17-4PH stainless steel is investigated. The nitriding was performed at 530 °C, 560 °C, and 580 °C for 2 h. The nitriding process improves the hardness and surface roughness of the AM 17-4PH steel. Detailed microstructural characterizations of both as-built and nitride samples are performed using an optical microscope, scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction technique. It reveals that the nitride layer thickness increases with nitriding temperature. A distinct transition layer between the substrate and nitride layer is observed in the 560 °C and 580 °C nitride samples. The nitriding process develops almost equiaxed grain microstructure with new secondary phase precipitates, whereas in the as-built material, the grains are primarily columnar along the AM process build direction. Specifically, the nitriding process introduces γ-Fe4N, ε-Fe3N, CrN, and Ni3N precipitates. The increase in Ni- and Cu-rich precipitates with the nitriding temperature explains the observed improvement in the hardness and surface roughness. Furthermore, the nitriding process does not alter the substrate's initial weak crystallographic texture.

17-4PH steel↗

DOE OSTI2025

Creep Deformation and Damage Mechanisms in an Advanced High-Temperature Additively Manufactured Nickel-Base Superalloy

Abstract This research investigates the processing–structure–properties–performance relationship in a novel nickel-base superalloy, ABD ® -900AM, designed for extreme environments. Specifically tailored for additive manufacturing (AM), ABD ® -900AM maintains mechanical integrity at high temperatures and is comparable to other nickel-based superalloys with a 30–40% gamma-prime volume fraction. A comprehensive study was conducted using laser-beam powder bed fusion and electron-beam powder bed fusion methods. Factors such as heat treatment, porosity, build orientation, and hot isostatic pressing were evaluated to understand their effects on microstructure and mechanical performance. Microstructural characterization revealed significant differences in grain size and orientation across build processes and heat treatments. High-temperature mechanical testing indicated that grain size, heat treatment, and orientation significantly influence creep behavior. A super-solvus heat treatment led to recrystallization and grain growth, significantly improving creep properties compared to a near-solvus heat treatment. Various creep mechanisms were identified across different conditions, and creep rupture models were developed for each build process. Post-test microstructural analysis showed grain boundary damage, with differences in creep cavitation morphology under varying stress conditions. It was shown that MC carbides grow at the expense of gamma-prime near grain boundaries, leading to precipitate-free zones in specimens tested at higher temperatures. This study fills a significant gap in fundamental research by offering a deeper insight into the high-temperature mechanical behavior of additively manufactured nickel-base superalloys. It also explores critical research questions regarding the role of carbides and the significance of heat treatment. The insights gained enhance confidence in the industry adoption of ABD ® -900AM and similar alloys for high-temperature applications, bridging the knowledge gap and supporting the development of reliable AM processes for extreme environments.

Bridges, Alex (ORCID:000000030338759X)↗

DOE OSTI2021

Varied enhancements in mechanical properties and sodium compatibility of Grade 92 by thermomechanical treatments

As a candidate material for advanced nuclear reactors, a ferritic-martensitic (FM) steel Grade 92 in the standard normalized and tempered (NT) condition was subjected to two types of thermomechanical treatments (TMTs) with one having a lower level of deformation (T5A) and the other having a higher level of deformation (T5B). The testing results of the three conditions indicated that the TMTs significantly improved yield strength, creep resistance, fracture toughness, and sodium corrosion resistance compared with the NT condition. T5A excelled at creep resistance while T5B at sodium corrosion resistance. Microstructural characterization of the three conditions supports the varied enhancements in the properties. This study suggests that an appropriate TMT can be developed and applied to FM steels to better meet specific application requirements.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Insights on carbon dioxide adsorption in a flexible 1-D coordination polymer from in situ X-ray scattering and density functional theory

A combination of in situ small-angle X-ray scattering (SAXS) microstructure characterization over scales ranging from 1 nm to 10 µm and powder X-ray diffraction (XRD) structure characterization under various gas/pressure/temperature conditions with density functional theory (DFT) calculations provides new insights for the CO2 sorption behavior of a one-dimensional porous coordination polymer: catena-bis(dibenzoylmethanato)(4,4′-bipyridyl)nickel(II), denoted NiDBM-Bpy. The NiDBM-Bpy chains are held together by van der Waals forces, but the structure of guest-free NiDBM-Bpy is unsolved due to a lack of suitable crystals and high-quality powder XRD patterns. Nevertheless, SAXS and powder XRD can follow microstructural and structural changes as a function of gas pressure, composition and temperature. Both mixed-gas flow and static supercritical CO2 regimes are explored experimentally. DFT calculations are used to model the structural variation associated with XRD changes and hysteresis in the sorption isotherms. XRD and DFT calculations suggest that an orthorhombic Fddd structure with two CO2 per Ni emerges following a transition from the structure with lower molar volume and symmetry that exists without CO2 present.

Allen, Andrew J.↗

DOE OSTI2024

Invertible Temper Modeling using Normalizing Flows and the Effects of Structure Preserving Loss

Advanced manufacturing research and development is typically small-scale, owing to costly experiments associated with these novel processes. Deep learning techniques could help accelerate this development cycle but frequently struggle in small-data regimes like the advanced manufacturing space. While prior work has applied deep learning to modeling visually plausible advanced manufacturing microstructures, little work has been done on data-driven modeling of how microstructures are affected by heat treatment, or assessing the degree to which synthetic microstructures are able to support existing workflows. We propose to address this gap by using invertible neural networks (normalizing flows) to model the effects of heat treatment, e.g., tempering. The model is developed using scanning electron microscope imagery from samples produced using shear-assisted processing and extrusion (ShAPE) manufacturing. This approach not only produces visually and topologically plausible samples, but also captures information related to a sample’s material properties or experimental process parameters. We also demonstrate that topological data analysis, used in prior work to characterize microstructures, can also be used to stabilize model training, preserve structure, and improve downstream results. We assess directions for future work and identify our approach as an important step towards end-to-end deep learning system for accelerating advanced manufacturing research and development.

Howland, Sylvia↗

DOE OSTI2026

Variation in supercurrent connectivity and vortex pinning of state-of-the-art pulsed laser deposited RE Ba 2 Cu 3 O 7- x coated conductors

REBa 2 Cu 3 O 7-x (REBCO, RE: rare earth) coated conductors (CCs) suffer from great critical current I c differences between different manufacturers, I c variations within individual manufacturers, and often significant lengthwise fluctuations. The understanding of such variations is complicated by the lack of a direct correlation between I c and the critical current density J c . In fact, although J c is the fundamental property determined by the local vortex pinning landscape, I c is often limited by variable current blocking mechanisms. An important practical complexity is commercial practices of performing J c and I c evaluations based on I c at 77 K and self-field (sf), where connectivity variation dominates over vortex pinning variations. However, at higher fields and lower temperatures, vortex pinning becomes more complex and highly variable, making predictions of I c and J c at arbitrary temperature T, magnetic field H, and field orientation θ, quite uncertain. To address some aspects of this problem, we conducted detailed spool-to-spool performance characterization on recently manufactured REBCO CCs. Despite J c (77 K, sf) varies by only ∼11%, J c (77 K, 1 T) of its minimum and maximum (for H//ab-plane) show variations of ∼21% and ∼32%, respectively. This emphasizes the shortcoming in using J c (77 K, sf) as parameter for evaluating even the low field performance. An even more remarkable spool-to-spool J c variation of ∼68% was observed at 20 K and 15 T for H//ab-plane. To identify the origin of such lack of reproducibility we performed microstructural characterizations, which revealed, within the REBCO layer, large variation in the density of copper oxide (CuO x ) particles ranging from 0.1 to 2 μm in size. We believe that they play a decisive role in reducing the effective cross-section of the REBCO layer by not simply blocking current themselves, but also by nucleating off-axis REBCO grains, whose misoriented grain boundaries adversely impact REBCO grain-to-grain connectivity. The REBCO growth associated with high density CuO x particles also leads to the more disordered spatial arrangement of BaHfO 3 precipitate arrays, which, when self-aligning along the ab-planes, generate stronger pinning enhancing J c (H//ab) at all temperatures. In this way, we established that variations of both connectivity and vortex pinning are thus directly coupled. Our results also explain why the so-called ‘lift-factor’, typically defined by the ratio between I c (T, H) and I c (77 K, sf), frequently turns out to be unreliable.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Extent of interlocking and metallurgical bonding in friction riveting of aluminum alloy to steel

In this study, the joining of 6061-T6 aluminum alloy and DP590 steel using a M42 steel rivet via friction riveting technique is investigated. The surface morphology and microstructure characterization reveal the formation of an anchor zone that imparts mechanical interlock as well as the formation of metallurgical bonds at the interface of aluminum and steel. A combination of interlocking and bonding results in the achievement of a high load-carrying capacity of 5.7 kN during lap shear testing at room temperature. A finite element-based computational model was developed which accurately predicted the lap shear response of the joint. The model revealed that the metallurgical bond formed during fric-riveting adds 39% peak load strength to the joint. An extensive microstructural investigation, post-lap-shear fractography, and the modeling results, together provided insights on the joint failure mechanism. In conclusion, this study highlights that friction riveting is a promising method for aluminum-to-steel dissimilar joining, which is important for lighweighing automotive vehicles for energy efficiency.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Comparing structure-property evolution for PM-HIP and forged alloy 625 irradiated with neutrons to 1 dpa

The nuclear power industry has growing interest in qualifying powder metallurgy with hot isostatic pressing (PM-HIP) to replace traditional alloy fabrication methods for reactor structural components. But there is little known about the response of PM-HIP alloys to reactor conditions. This study directly compares the response of PM-HIP to forged Ni-base Alloy 625 under neutron irradiation doses ~0.5–1 displacements per atom (dpa) at temperatures ranging ~321–385 °C. Post-irradiation examination involves microstructure characterization, ASTM E8 uniaxial tensile testing, and fractography. Up through 1 dpa, PM-HIP Alloy 625 appears more resistant to irradiation-induced cavity nucleation than its forged counterpart, and consequently experiences significantly less hardening. This observed difference in performance can be explained by the higher initial dislocation density of the forged material, which represents an interstitial-biased sink that leaves a vacancy supersaturation to nucleate cavities. These findings show promise for qualification of PM-HIP Alloy 625 for nuclear applications, although higher dose studies are needed to assess the steady-state irradiated microstructure.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗