SEARCH · Engineering Papers

Results for “microstructural analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Combinatorial measurement of critical cooling rates in aluminum-base metallic glass forming alloys

Direct measurement of critical cooling rates has been challenging and only determined for a minute fraction of the reported metallic glass forming alloys. Here, we report a method that directly measures critical cooling rate of thin film metallic glass forming alloys in a combinatorial fashion. Based on a universal heating architecture using indirect laser heating and a microstructure analysis this method offers itself as a rapid screening technique to quantify glass forming ability. We use this method to identify glass forming alloys and study the composition effect on the critical cooling rate in the Al–Ni–Ge system where we identified Al 51 Ge 35 Ni 14 as the best glass forming composition with a critical cooling rate of 10 4 K/s.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Rheology improvement for silicon nitride and resin slurries for vat photopolymerization printing and sintering

This work presents the formulation, rheological characterization, and sintering of silicon nitride (Si₃N₄) slurries for vat photopolymerization (VPP) using digital light processing (DLP). Bimodal Si₃N₄ powder was dispersed into commercial photopolymer resin using two different dispersants with opposing effects on surface charge, resulting in varied slurry stability and flow behavior. Slurries were engineered to exhibit shear-thinning behavior suitable for VPP, and their flow properties were quantified using a power-law fluid model. The formulations achieved cure depths of approximately 40 µm and enabled printing of green bodies. Post-processing included thermal debinding and liquid-phase sintering, yielding primarily β-Si₃N₄ with a minor Y-Si-Al-O-N glass phase. The sintered parts reached ~85% of theoretical density and demonstrated a flexural strength of ~330 MPa. Microstructural analysis revealed closed porosity along with some defects related to powder agglomeration and interlayer adhesion. These findings provide insights into slurry formulation strategies for additive manufacturing of high-performance non-oxide ceramics.

Aerospace engineering↗

DOE OSTI2021

Enhancing the multi-functional properties of renewable lignin carbon fibers via defining the structure–property relationship using different biomass feedstocks

Lignin has been explored extensively as a renewable precursor for carbon materials, considering its abundance as a major component of plant cell walls and its sustainability as a byproduct of both lignocellulosic biorefinery and the paper-making industry. Despite the extensive efforts to define the process–property relationship, it remains largely unknown how lignin biosynthesis and its chemistry would impact the resultant carbon fiber properties, for both mechanical and electroconductive performances. Such inadequate understanding fundamentally limits feedstock design and selection to improve carbon fiber properties toward broader commercial applications. Using lignin from a broad range of biomass feedstocks for carbon fiber manufacturing, we have fundamentally explored the structure–function relationship between lignin chemistry and carbon fiber performance. Specifically, lignin extracted from hardwood (sugar maple), softwood (loblolly pine and red cedar), and herbaceous plants (corn stover and switchgrass) was used for carbon fiber manufacturing, considering the very different lignin structures from these feedstocks. Linear regression models were established to define the relationship between carbon fiber mechanical properties and lignin structural characteristics. The results highlighted that the content of β-O-4 linkages correlates significantly with the tensile strength and elastic modulus of lignin carbon fibers, indicating that more linear β-O-4 linkages would promote the carbon fiber mechanical performance. Moreover, electroconductive properties are essential for broader energy device application of lignin-based carbon fibers, yet the mechanisms controlling their electroconductivity are largely unknown. Furthermore, we hereby demonstrated that a higher β-O-4 content also promotes the electroconductivity of lignin carbon fibers. Microstructure analysis further revealed that the crystallite size and content of the pre-graphitic turbostratic carbon structure in lignin-based carbon fibers were enhanced as the β-O-4 linkages increased. The content of β-O-4 linkages has shown a strong correlation with the crystallite content in a linear regression model. This study thus revealed the underlying mechanisms regarding how the lignin structure in planta defines the resultant carbon fiber properties. Moreover, the study also highlighted the correlation between the mechanical and electroconductive properties of lignin-based carbon fibers, both of which were defined by the lignin structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Tailorable multifunctionalities in ultrathin 2D Bi-based layered supercell structures

Two-dimensional (2D) materials with robust ferromagnetic behavior have attracted great interest because of their potential applications in next-generation nanoelectronic devices. Aside from graphene and transition metal dichalcogenides, Bi-based layered oxide materials are a group of prospective candidates due to their superior room-temperature multiferroic response. In this work, an ultrathin Bi 3 Fe 2 Mn 2 O 10+δ layered supercell (BFMO322 LS) structure was deposited on an LaAlO 3 (LAO) (001) substrate using pulsed laser deposition. Microstructural analysis suggests that a layered supercell (LS) structure consisting of two-layer-thick Bi–O slabs and two-layer-thick Mn/Fe–O octahedra slabs was formed on top of the pseudo-perovskite interlayer (IL). A robust saturation magnetization value of 129 and 96 emu cm -3 is achieved in a 12.3 nm thick film in the in-plane (IP) and out-of-plane (OP) directions, respectively. The ferromagnetism, dielectric permittivity, and optical bandgap of the ultrathin BFMO films can be effectively tuned by thickness and morphology variation. In addition, the anisotropy of all ultrathin BFMO films switches from OP dominating to IP dominating as the thickness increases. This study demonstrates the ultrathin BFMO film with tunable multifunctionalities as a promising candidate for novel integrated spintronic devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2021

Selenium infiltrated hierarchical hollow carbon spheres display rapid kinetics and extended cycling as lithium metal battery (LMB) cathodes

Lithium metal–selenium (Li–Se) batteries offer high volumetric energy but are limited in their cycling life and fast charge characteristics. Here a facile approach is demonstrated to synthesize hierarchically porous hollow carbon spheres that host Se (Se@HHCS) and allow for state-of-the-art electrochemical performance in a standard carbonate electrolyte (1 M LiPF 6 in 1:1 EC:DEC). The Se@HHCS electrodes display among the most favorable fast charge and cycling behavior reported. For example, they deliver specific capacities of 442 and 357 mA h g -1 after 1500 and 2000 cycles at 5C and 10C, respectively. At 2C, Se@HHCS delivers 558 mA h g -1 after 500 cycles, with cycling coulombic efficiency of 99.9%. Post-mortem microstructural analysis indicates that the structures remain intact during extended cycling. Per GITT analysis, Se@HHCS possesses significantly higher diffusion coefficients in both lithiation and delithiation processes as compared to the baseline. Furthermore, the superior performance of Se@HHCS is directly linked to its macroscopic and nanoscale pore structure: the hollow carbon sphere morphology as well as the remnant open nanoporosity accommodates the 69% volume expansion of the Li to Li 2 Se transformation, with the nanopores also providing a complementary fast ion diffusion path.

25 ENERGY STORAGE↗

DOE OSTI2024

NiGa 2 O 4 interfacial layers in NiO/Ga 2 O 3 heterojunction diodes at high temperature

NiO/Ga 2 O 3 heterojunction diodes have attracted attention for high-power applications, but their high temperature performance and reliability remain underexplored. Here, we report the time evolution of the electrical properties in the widely studied p-NiO/n-Ga 2 O 3 heterojunction diodes and formation of NiGa 2 O 4 interfacial layers at high temperatures. Results of our thermal cycling experiment show an initial leakage current increase which stabilizes after sustained thermal load, due to reactions at the NiO–Ga 2 O 3 interface. High-resolution TEM microstructure analysis of the devices after thermal cycling indicates that the NiO–Ga 2 O 3 interface forms a ternary compound at high temperatures, and thermodynamic calculations suggest the formation of the spinel NiGa 2 O 4 layer between NiO and Ga 2 O 3 . First-principles defect calculations find that NiGa 2 O 4 shows low p-type intrinsic doping and hence can serve to limit electric field crowding at the interface. Vertical NiO/ Ga 2 O 3 diodes with intentionally grown 5 nm thin spinel-type NiGa 2 O 4 interfacial layers show an excellent device ON/OFF ratio of >10 10 (± 3 V), V ON of ~1.9 V, and increased breakdown voltage of ~1.2 kV for an initial unoptimized 300 lm diameter device. These p–n heterojunction diodes are promising for high-voltage, high temperature applications.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2025

Cr-Be Pushered Single Shell (PSS) Capsule Development

Pushered single shell (PSS) has emerged as an alternative platform of implosion to ease the stability issue at the ablation front. The design consists of a thin inner Be layer, a 50% Cr:Be plateau region, an S-curve gradient, a low Cr (1.5%) tamper layer, and followed by a pure Be outer layer. General Atomics has developed a way to fabricate the higher-Z Cr to lower-Z Be gradients on glow discharge polymer mandrels with a designed S-shape profile for optimal implosion stability using magnetron sputtering. Microstructure analysis of the gradient coating indicated that at lower Cr concentration a short order or amorphous structure was formed. Here, these fabricated PSS capsules were subsequently built into capsule fill tube assemblies, verified to be leak tight at both ambient and cryogenic conditions, and delivered to Lawrence Livermore National Laboratory for the shots. The capsule thermal stability was demonstrated by invariable Cr profiles before and after pyrolysis. However, cracking at inner Cr layers was observed, which has been attributed to thermal stress.

Capsule↗

DOE OSTI2022

Tungsten doped diamond shells for record neutron yield inertial confinement fusion experiments at the National Ignition Facility

We report on fabrication and characterization of layered, tungsten doped, spherical about 2 mm diameter microcrystalline diamond ablator shells for inertial confinement fusion (ICF) experiments at the National Ignition Facility. As previously reported, diamond ICF ablator shells can be fabricated by chemical vapor deposition (CVD) on solid spherical silicon mandrels using an ellipsoidal microwave plasma reactor. In the present work, we further developed these ablator shells by embedding a W -doped diamond layer sandwiched between two undoped diamond regions. W incorporation in diamond was achieved by adding tungsten hexacarbonyl to the CH 4 /H 2 CVD feed gas. We observe that the W doping concentration decreases with increasing deposition rate which, in turn, is controlled by adjusting the total gas pressure. Cross sectional microstructural analysis reveals sharp interfaces between doped and undoped regions of the diamond shell and uniform W distribution with concentrations up to about 0.3 at.%. At higher W concentrations (>0.3 at.%) formation of tungsten carbide precipitates is observed. Using a 3-shock 1.6 MJ laser pulse, the targets described in this work produced the first laser driven implosion to break the 1 × 10 16 neutron yield barrier, followed by experiments (described in future publications) with similar targets and slightly more laser energy producing yields as high as 4 × 10 17 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Age and growth of early‐life‐stage Atlantic tarpon ( Megalops atlanticus) from the northcentral Gulf of Mexico

Abstract Age and growth of early‐life‐stage Atlantic tarpon Megalops atlanticus collected from Mississippi coastal waters in the northcentral Gulf of Mexico (GOM) are described using otolith microstructure analysis. Tarpon leptocephali ( n = 95, 16.0—27.8 mm standard length, L S ) collected from June throughOctober 2013—2018, ranged in age from 22 to 43 days (mean = 30.9 ± 0.5 days). Leptocephalus somatic growth rates ranged 0.46—1.24 mm day −1 (mean = 0.76 ± 0.02 mm day −1 ), and leptocephalus otolith growth rates ranged 1.78—3.97 μm day −1 (mean = 2.58 ± 0.04 μm day −1 ). Growth rates were inversely correlated to leptocephalus age, indicating the shrinkage phase associated with leptocephalus metamorphosis. Juvenile tarpon ( n = 358, 50—359 mm fork length, L F ) were collected from August through December 2007—2018. Juveniles exhibited a positive allometric relationship (adjusted R 2 = 0.99, P < 0.001) between length and mass. The age of 100 juveniles (71—277 mm L F ) ranged from 76 to 174 days. Juvenile growth rate was estimated as 1.56 ± 0.11 mm day −1 . Significant ( P < 0.001) linear relationships were found between juvenile age and otolith metrics, including otolith mass ( R 2 = 0.81) and radius ( R 2 = 0.68). Evaluation of the backcalculated hatch dates suggests that specimens in the collection hatched from late May through mid‐September with slight peaks during July and August. A Rao's Spacing Test of Uniformity indicates the presence of significant lunar periodicity in leptocephalus hatch dates ( n = 95, U = 250.1, P < 0.05), with 50% of the leptocephali hatched within 5 days (before or after) of the full moon. This study fills critical gaps in the scientific knowledge of tarpon and provides estimates of early‐life‐history metrics for an iconic game fish at the northernmost extent of its GOM range.

Graham, Patrick M.↗

DOE OSTI2023

Property-Graded Stainless Steel 316L by Selective Laser Melting: Characterization & Design

Abstract The purpose of this research work is to characterize and inform the design of (mechanical) property-graded bulk structures made from a single metallic alloy via a laser powder bed fusion (LPBF) process, with an end goal of creating repeatable/reproducible functionally-graded additively manufactured (FGAM) parts. This paper specifically investigates the manufacture of stainless steel (SS) 316L structures via a pulsed selective laser melting (SLM) process, and the underlying causes of property variations (within a functionally-acceptable range) through various material characterization techniques. For this, a design of experiments spanning the volumetric energy density (VED) based process parameter design space was utilized to investigate the range of functionally-acceptable physical/mechanical properties achievable in SS 316L. Five sample conditions (made via different process parameter combinations) were down-selected for in-depth microstructure analysis and mechanical/physical property characterization; these were suitably selected to impart a wide and controllable property range (209–318 HV hardness, 90–99.9% relative density, and 154–211 GPa modulus). It was observed that property variations resulted from combinations of porosity types/amounts, martensitic phase fractions, and grain sizes. Based on these findings, property-graded standard test specimens were designed and manufactured for further investigation—tensile specimens having a monotonic hardness change along its gauge length, four-point bending specimens with varying elastic moduli as a function of the distance from the neutral axis, and Moore’s rotating beam fatigue specimens with moduli variations based on the distance from the center. Altogether, this work lays the foundation for understanding and designing the local and global mechanical performance of FGAM bulk structures.

Engineering↗

DOE OSTI2023

Neutron Characterization of 3D Printed Gas Turbine Alloy With Internal Cooling Structure

The objective of this research work is to investigate the residual strains induced by the presence of a exit hole and internal hollow geometry present in a 3D printed IN718 similar to that seen in a gas turbine blade. The specimens were manufactured with an internal hollow structure that ended with an exit hole, and fabricated by direct metal laser sintering additive manufacturing technique. Using this technique, metal powder was melted by a laser source and rapidly cooled to form the part layer by layer. Rapid heating and cooling generate large thermal gradients and residual stresses in the 3D printed material. To be aligned with industry standards, specimens were heat-treated to relieve most of the residual stresses as well as to investigate whether IN718 still preserved a nonhomogeneous stress state after the thermal treatment. Roughness and microstructure analysis was performed to understand the heat-treated sample properties. To investigate the volumetric residual strain, the neutron diffraction technique was used with a definite neutron wavelength. Bragg’s law was used to determine lattice spacing. Interplanar lattice spacing and stress-free state lattice spacings were measured to calculate the strains. Residual strains were measured in the x and y direction to understand the impact of the presence of a exit hole and internal hollow geometry. The results of volumetric residual strain in the x and y directions showed no significant variations in the distribution of the strain due to the presence of a hollow structure as well as the exit hole. Overall, no significant stress concentration was observed in the heat treated sample. Sample geometry, instrumentation for neutron diffraction, and material properties are discussed in detail in this paper.

Raju, Nandhini↗

DOE OSTI2025

Compatibility of molten plutonium with wrought and additively manufactured metal crucibles

Understanding plutonium’s interaction with metals is crucial for optimizing pyrochemical operations, nuclear fuel containment, and various actinide processing techniques. Traditionally, tantalum crucibles are employed for plutonium processing due to their high durability, excellent temperature stability, and low solubility in plutonium. However, tantalum faces challenges such as plutonium wetting and diffusion, making surface coatings particularly important for crucibles in pyrochemical applications to enhance corrosion resistance against plutonium. Tantalum is also expensive and difficult to machine, prompting the need for advanced manufacturing techniques to address these challenges. Here, in this work, we investigate the interaction of Pu with tantalum and titanium crucibles fabricated using both traditional machining methods and laser powder bed fusion (LPBF) additive manufacturing (AM). LPBF-AM is an advanced technique that allows for the creation of complex geometries from traditionally difficult-to-machine metals by using a high-powered laser to build parts. Previous studies of conventional manufactured tantalum have utilized oxidation and carburization of the surface to mitigate plutonium wetting; however, no studies of surface modified LPBF-AM material have been undertaken. These studies are crucial, given the typical differences in the grain structure between conventional and LPBF-AM materials. All crucibles underwent differential scanning calorimetry to confirm the melting of plutonium. Subsequently, the crucibles were sectioned and mounted in epoxy for microstructural analysis using optical microscopy and scanning electron microscopy. This investigation, comparing the performance of wrought vs AM metal crucibles, provides a basis for future tooling applications in actinide processing techniques and can address the challenges associated with traditional machining, particularly in pyrochemical applications.

Actinides↗

DOE OSTI2022

Mechanisms of Retention and Transport of Fission Products in Virgin and Irradiated Nuclear Graphite

To fulfill the design and licensing requirements for advanced reactors, the U.S. Department of Energy (DOE) is specifically interested in targeted research to quantify the mechanisms of fission product transport and retention in graphitic grades that will likely be used in next-generation very/high temperature reactors, fluoride salt-cooled high temperature reactors and molten salt reactors. We have examined an integrated experimental-computational approach to determine the diffusivities of selected fission products – ruthenium (Ru) and silver (Ag) in five nuclear graphite grades – POCO AXF-5Q, POCO ZXF-5Q, PCEA, IG110, and NBG-18. Experimental investigation for diffusion of other fission products (iodine, cesium, and krypton) in graphite could not be carried out due to extreme evaporation due to high vapor pressure, despite several attempts incorporating various experimental schemes. Experimental investigation with irradiated graphite could not be carried out because necessary approval to transport irradiated graphite could not be obtained due to procedural reasons at ORNL and national policy change in UK. An effort was made to “produce” by ion sputtering, but it was discontinued because the outcome did not adequately represent irradiated graphite. Thin film and “cup-and-cap” methods were employed to deposit fission products, diffusion annealed were carried out in an argon atmosphere, and concentration profiles were determined by dynamic secondary ion mass spectroscopy depth profiling technique. Regardless of graphite type, anomalous diffusion behavior of Ru (i.e., lower than expected based on Arrhenius temperature dependence) at an intermediate temperature, around 600 to 700 °C, was observed. Diffusion behavior of silver on the other hand agreed well to the Arrhenius temperature dependence although the excessive evaporation of silver hampered the accurate determination of diffusivities at temperature higher than 900 °C. In general, silver was observed to diffuse faster than Ru in the temperature range compared from 500 to 900 °C, had consistently had higher pre-exponential factor corresponding to higher jump frequency. To understand the abnormal diffusional behavior of Ru in graphite in intermediate temperature range, a detailed microstructural analysis was carried out. Clustering of Ru into particles on the surface of graphite was observed around 700 °C corresponding to de-wetting and spheroidization. This change would influence the boundary condition of diffusion, although features of clustering was much smaller (<1 mm) than the SIMS raster size (120 x 120 mm). Raman spectroscopy also demonstrated that Raman peak intensity for Ru decreased significantly for samples annealed higher than 700 °C and presence of Ru in graphite altered the crystallinity of graphite. To further elucidate the abnormal diffusion behavior observed in intermediate temperature investigated, the vibrational properties of graphene, bilayer graphene and Kr atoms in bilayer graphene were investigated with molecular dynamics. Krypton, which is a fission product, was introduced between a bilayer graphene system to evaluate (i) whether the phonon dispersion curves change with high temperature in bilayer graphene (ii) whether the addition of Kr atoms between the bilayer introduces any significant change in the vibrational properties, and (iii) whether any change in the vibrational properties can be correlated to the diffusive behavior of Kr atoms. The results show that the Kr atoms indeed exhibit an anomalous diffusive behavior at 550°C. Phonon analysis shows that a few phonon frequencies are enhanced as much as 20 to 30 % with the addition of just 0.2 at.% Kr. So, this may explain the unexpected self-diffusivity of fission products.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Laser Surface Processing of Alloys for Corrosion Protection (Final Project Report of Marine Energy Seedling Project)

This is the final project report for the MHK Seedling project. The report describes use of laser surface processing (LSP) to modify the surface of test materials (Al, steel) and the corrosion testing performed on the resulting samples in different corrosion environments. Data shows that LSP improved the corrosion resistance of Al and steel used in this work relative to respective non-LSP samples. The data also showed that each material had a specific range of laser processing conditions where the beneficial effects of LSP (i.e. improvement in corrosion protection) were observed. Application of LSP to enable low-cost materials in marine environments, additional microstructural analysis and long-term testing are proposed to further develop this technology for marine renewable energy and systems.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Capability to Process and Characterize Uranium-Zirconium (U-Zr) and Uranium-Zirconium-Plutonium (U-Zr-Pu) Alloys

This work investigated co-reduction of anhydrous compounds of uranium, zirconium, and plutonium to produce uranium rich ternary nuclear fuel alloys. Metallothermic co-reduction is a novel method to produce all-metal nuclear fuels. Metal fuels offer thermal, fissility, compatibility, and security benefits over oxide fuels. Alloys of uranium–10% zirconium with plutonium contents of 0%, 2.5%, 5%, and 10% were produced, with yields of 60–85% of theoretical values in a traditional calciothermic bomb reduction apparatus. Microstructural analysis indicated transformation of uranium phase from gamma to beta and then alpha, in alternating lamellar plates typical of alpha phase uranium and delta phase uranium-zirconium, with zirconium and carbides at prior grain boundaries. Some of the analyses were inconclusive in their results and therefore require additional testing. Successful ternary co-reduction would simplify production of homogeneous feedstock and thereby streamline manufacture of homogeneous ternary metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Process Intensification for Nanostructure Aluminum Extrusions

A new technology called Shear Assisted Processing and Extrusion (ShAPE™), pioneered at the Pacific Northwest National Laboratory (PNNL), has the potential to revolutionize the US extrusion industry. Maturation of the ShAPE™ process would create a new cross cutting US manufacturing technology that advances three key the objectives within AMO; namely, nanomaterials processing, process intensification, and materials for extreme and harsh environments. PNNL and SCM Metals Products, Inc. (SCM), a division of Kymera International, will collaborate to mature the ShAPE™ extrusion process beyond TRL 3 to increase the likelihood of its adoption by industry. PNNL’s custom (one-of-a-kind in the world) ShAPE™ machine will be used to extrude round rods of high strength aluminum alloy feedstock powder provided by SCM. As proof-of-concept, PNNL has previously extruded 5 mm diameter rods with SCM aluminum alloy powder AL-12.4TM. This project aims to scale up the process to a diameter of 25 mm while retaining the excellent mechanical properties achieved for the 5 mm diameter rods. The degree of process intensification with ShAPE™ will also be estimated. The primary objectives of this project are as follows. 1) Fabricate 25 mm diameter nanostructured extrusions in bulk, directly from AL-12.4TM aluminum alloy powder without the need for canning, degassing, compaction, and other intermediate steps typical of powder metallurgy extrusion. 2) Achieve a microstructure with an ultrafine grained (UFG <1 µm) aluminum matrix having refined and homogenously distributed nanoscale second phases. 3) Show that the ram force can be significantly reduced compared to conventional powder metallurgy extrusion of the same material and estimate the extent of process intensification that may be possible with ShAPE™. 4) Demonstrate improved high-temperature mechanical properties compared to conventional extrusion of the same material. The following tasks will be undertaken to achieve these objectives. PNNL will develop the die set and process parameters necessary to fabricate Al-12.4TM extrusions with a 25 mm diameter. Microstructural analysis will be performed by PNNL while mechanical testing will be conducted by SCM. With information learned from the process development and characterization, PNNL will perform an estimate of the degree of process intensification that may be possible with ShAPE™.

42 ENGINEERING↗

DOE OSTI2024

Laser Powder Bed Fusion of Steels for Nuclear Applications

This report provides an update on laser powder bed fusion of steels for nuclear applications. This report is a Milestone 3 deliverable in FY2024, under work package CT-24AN130401 to support research and qualification activities supported by the Advanced Materials and Manufacturing Technologies (AMMT) program here at Argonne National Laboratory (ANL). Continuing from FY23, the focus of FY24 for ANL includes further optimization of process parameters for three alloys: A709, G91, G92. The work package also includes fabricating test samples to conduct a thorough microstructural analysis and perform preliminary mechanical testing. For the same, we have used CALPHAD-based thermodynamic kinetic modeling to optimize the experimental activities.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗