Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “layered solid element”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Solidification of REDC Organics and Airborne Release Fraction Measurements

The Radiochemical Engineering Development Center (REDC) generates various liquid organic wastes from processing irradiated targets to recover heavy elements. In the past, these organics were discharged to the Oak Ridge National Laboratory (ORNL) liquid low-level waste (LLLW) system, along with the aqueous waste. Because of a reduction in aqueous LLLW from other ORNL generators and an increase in the radionuclide concentration, particularly 238 Pu, in the organic waste stream, the organics can no longer be discharged to the LLLW system. The plan is to solidify the liquid organic waste for disposal as solid debris waste. The documented safety analysis for REDC uses an airborne release fraction of 5 x 10 -4 with a respirable fraction of 0.2 for plutonium and other actinides from packaged solid debris waste during a fire scenario, for an overall airborne release fraction/respirable fraction of 10 -4 . Solidifying the organic liquids, either by using PM-199 Organoclay ® or by grouting, would produce solid waste forms with no free liquid, which should qualify for disposal at the Waste Isolation Pilot Plant. The use of Organoclay would be much simpler to implement inside a hot cell. Granular Organoclay can be added to the organic waste solutions until there is a dry layer on top of the liquid and then allowed to cure for a few hours. Grouting the liquids would require using multiple ingredients and mixing steps. Both methods produced waste forms that trapped cerium, as a surrogate for plutonium, inside the waste, with airborne release fractions during fire scenario tests of well below the 10 -4 limit.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Impact of Cr and Co on 99Tc retention in magnetite: A combined study of ab initio molecular dynamics and experiments

This work explores the effect of co-mingled dopants, Co(II) and Cr(III), on Tc(IV) incorporation and retention in magnetite when heat treated to 625 or 700 °C. Key trends in Tc retention in the high temperature regime were identified using a combination of density-functional-theory based ab initio molecular dynamics (AIMD) simulations, and batch experiments including solid phase characterization techniques, e.g. X-ray absorption spectroscopy. A stabilizing effect on Tc(IV) was observed when the number of Tc and Cr atoms are equal or when the magnetite surface is oversaturated with Tc and Cr inclusions. Here, oversaturation is hypothesized to force Cr from the magnetite surface to form a Cr2O3 phase, which may act as a protective layer that prevents Tc release. With the addition of Co, Tc(IV) is stabilized via redox processes. The presence of Cr in low concentrations interferes with this redox stabilization and Cr is preferentially stabilized as opposed to Tc. As a result, using Co as a stabilizing dopant for Tc may be compromised in the presence of Cr. When the relative concentration of Tc, Cr and Co is the same, or more Co atoms are added to high Cr incorporated systems, the formation of the Cr2O3 phase may be suppressed. Although waste streams with co-mingled Tc and Cr potentially may benefit from a Co dopant, since the formation of a Cr2O3 passivation layer may protect incorporated Tc from being released, the relative concentration of the three elements will be a critical parameter for maximizing effectiveness of this strategy.

Lee, Mal Soon↗
DOE OSTI2020

Phase stabilization and oxidation of a continuous composition spread multi-principal element (AlFeNiTiVZr) 1-x Cr x alloy

Multi-Principal Element Alloys (MPEA) have been hypothesized to maintain a stable single alloy phase and resist corrosion at high temperatures, which are desirable in various functional applications, including material of turbine blades. However, studies into oxidation resistant alloys have been constrained to individual MPEA systems or a limited selection of compositions within those systems. Here, High-Throughput Experimental (HTE) techniques were utilized to rapidly assess phase stability and resistance to oxidation of an (AlFeNiTiVZr) 1-x Cr x continuous composition spread (CCS) thin-film alloy system. High-throughput synchrotron diffraction and Raman spectroscopy were used to identify phases, especially high symmetry structures and oxides, as a function of annealing time and composition. The formation of two distinct phase regions, R 1 and R 2 , across the CCS was observed. One of these phase regions, R 2 , exhibited a stable high symmetry BCC-like phase at Cr concentrations greater than 25.4 at%, and grew a passivating mixed metal surface oxide; whereas, the R 1 phase region, decomposed on oxidation to multiple oxides and reacted with the substrate to form silicides. The passivating mixed metal oxide layer appears to prevent destabilization of the (AlFeNiTiVZr) 1-x Cr x MPEA BCC solid solution. Furthermore, at longer annealing times the passivating phase was seen only above 29.2 at% Cr. High Cr-doped (AlFeNiTiVZr) 1-x Cr x appear to be a good candidate for high temperature, oxidation-resistant structural alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of H + Exchange and Surface Impurities on Bulk and Interfacial Electrochemistry of Garnet Solid Electrolytes

Contact loss and current constriction pose significant challenges at the Li metal interface of solid-state batteries. For garnet-structured Li 7 La 3 Zr 2 O 12 (LLZO), these effects are amplified by Li + /H + exchange and surface contamination reactions, which lead to conductivity losses and poor Li wetting. In this study, we utilize a variety of surface treatment processes across 37 cells to selectively induce proton exchange and contamination reactions in LLZO. The resulting bulk and surface chemistry is systematically characterized and correlated to changes in electrochemical properties. Additionally, we combine impedance analysis and finite element method modeling to deconvolute sources of impedance contributions at the Li metal interface. Specifically, we show that constriction impedance at the Li metal interface arises not solely from voids, but also from ionically-resistive surface contaminants. Further, these findings emphasize the connection between ionic conductivity and constriction, demonstrating that micron-scale ionically-resistive components increase constriction even with identical contact geometries. Finally, we leverage our comprehensive dataset to highlight unstable overpotential growth as a failure mechanism, additionally showing that the phase of a cell’s impedance is a sensitive indicator for the onset of interfacial instability. Overall, this study clarifies the impacts of proton exchange and surface contamination on electrochemical properties at the Li|solid electrolyte interface and elucidates insights that are generalizable to other solid-state battery systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Final Technical Report - Rapid Surface Microanalysis using a Low Temperature Plasma

This project focused on improving our current understanding and scientific knowledge in the area of plasma-surface interactions and plasma assisted material synthesis related to advanced microelectronics and nanotechnology. Current challenges include: controlling the interaction of Low Temperature Plasma (LTP) with a single layer of atoms to manufacture integrated circuits, continued miniaturization of integrated circuits, LTP processing of material surfaces and thin films to enable industrial scale fabrication of advanced microelectronics, synthesis of new materials, nanomaterials, nanotubes, and complex materials, Technology developed in this subtopic is of value to either (i) enable scans of surfaces (~1 sq. cm area) using various microscopies (electron, optical, other) at high resolution (micron or sub-micron resolution) rapidly (hours or days rather than years to complete a high-resolution scan of such a large surface area), or (ii) enable scans of surfaces (~1 sq. cm area) using various microscopies (electron, optical, other) at relatively low resolution rapidly, then apply algorithms to select spots for micron-scale imaging. Sputtering occurs when particles of a solid material are ejected from its surface by energetic particles from a plasma. While the degradation of the solid material and the subsequent deposition of the ejected material onto vulnerable surfaces are the usual subjects of sputtering studies, plasma science has yet to be combined with sputtering to create new diagnostics devices and systems. Small changes in the design of the plasma discharge device make it possible to create broad plasma beams for rapid scanning or small plasma beams to obtain the distribution of ejected elements with micron resolution. In the high-resolution use, the ion flux is extracted from the gas-discharge plasma and focused by a spherical emission surface to micron sizes onto the target specimen, providing very local sputtering and local elemental analysis. We call this “self-focusing”. The radiation from the excited and ionized sputtered atoms is recorded by a spectrometer through a window and fiberglass cable and analyzed with standard software packages used for optical glow discharge spectroscopy. Computer simulations of beam formation were used to verify and optimize the designs to be tested. A prototype was designed, constructed, and used to start experiments of beam formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Pristine Interface between Lithium Lanthanum Zirconate and Lithium Manganese Oxide by Pulsed Laser Deposition

Solid state lithium-ion batteries have garnered increasing interest in recent years due to several potential advantages over liquid-electrolyte based systems. The possibility of integrating the lithium garnet oxide, Li 6.75 La 3 Zr 1.75 Ta 0.25 O 12 (LLZTO), with the high voltage cathode, spinel Li x Mn 2 O 4 (LMO), is evaluated here. Thin film bilayer structures are prepared by pulsed laser deposition on MgO (001) substrates and characterized by x-ray diffraction and transmission electron microscopy. The LLZTO is grown by an alternating layer-by-layer deposition of LLZTO and Li 3 N and subsequently annealed for several hours at 575 °C to promote crystallinity. Growth of crystalline LMO with a pristine interface to LLZTO is achieved by gentle heat treatment (500 °C) to remove surface carbonate from the electrolyte and by cathode growth at a low temperature of 250 °C. Higher temperature depositions (330 – 450 °C) result in reaction between the two materials and the appearance of Li 2 MnO 3 , which may be in part due to the presence of excess lithium in the electrolyte layer. Because fully lithiated LiMn 2 O 4 has a voltage of ≈3.7 V versus Li+/Li, the observation of a well-defined interface, free of impurity phases and with no interdiffusion of elements, indicates LLZTO is stable to at least 3.7 V.

Garnet LLZO↗
DOE OSTI2022

Enhancing high-fidelity nonlinear solver with reduced order model

Abstract We propose the use of reduced order modeling (ROM) to reduce the computational cost and improve the convergence rate of nonlinear solvers of full order models (FOM) for solving partial differential equations. In this study, a novel ROM-assisted approach is developed to improve the computational efficiency of FOM nonlinear solvers by using ROM’s prediction as an initial guess. We hypothesize that the nonlinear solver will take fewer steps to the converged solutions with an initial guess that is closer to the real solutions. To evaluate our approach, four physical problems with varying degrees of nonlinearity in flow and mechanics have been tested: Richards’ equation of water flow in heterogeneous porous media, a contact problem in a hyperelastic material, two-phase flow in layered porous media, and fracture propagation in a homogeneous material. Overall, our approach maintains the FOM’s accuracy while speeding up nonlinear solver by 18–73% (through suitable ROM-assisted FOMs). More importantly, the proximity of ROM’s prediction to the solution space leads to the improved convergence of FOMs that would have otherwise diverged with default initial guesses. We demonstrate that the ROM’s accuracy can impact the computational efficiency with more accurate ROM solutions, resulting in a better cost reduction. We also illustrate that this approach could be used in many FOM discretizations (e.g., finite volume, finite element, or a combination of those). Since our ROMs are data-driven and non-intrusive, the proposed procedure can easily lend itself to any nonlinear physics-based problem.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

Role of Elemental Substitution on Hydrogen Incorporation in Characteristic Ti/Fe-Based Oxides

Elemental substitution is well-known to benefit hydrogen storage in the intermetallic compound TiFe; however, the impact of these substituents on the native and passivating surface oxide has not been well-established. Here, we perform density functional theory calculations on several characteristic oxides that are likely to form on exposed TiFe surfaces, specifically, TiO 2 , FeO, TiFeO 3 , and Ti 4 Fe 2 O. In TiO 2 and TiFeO 3 , additional acceptor species substituting for Ti can increase the solubility of protonic hydrogen (H i + ), likely enhancing hydrogen permeation of the oxide layer. In FeO, few dopants will act as acceptors, and hydrogen will incorporate as substitutional H O + , which is likely to be less mobile and will hinder hydrogen permeation. Finally, we find that Ti 4 Fe 2 O, which is thermodynamically metastable, may be stabilized by defects under O-poor conditions, although the presence of certain substitutional elements can destabilize it. In general, Mn, V, and Cr are among the best substituents for enhancing hydrogenation through the oxide layer. In conclusion, our results help to explain what features make additional elements particularly effective for enabling reversible hydrogen storage in TiFe, and they can guide further technological development of high-performing TiFe-based alloys for future energy applications.

organic↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
DOE OSTI2021

Evaluation of Phase Change Plaster/Paste Composites for Building Envelopes

Thermal energy storage (TES) materials increase a building’s thermal mass and provide the flexibility to shave and time-shift energy use. These materials are needed to enable grid-interactive efficient buildings, allowing building occupants to lower costs by leveraging free ambient heating/cooling as well as shifting consumption to cheaper electricity periods. Phase change materials (PCMs) that store heat through a solid-liquid/solid-solid transformation are of particular interest for TES because of their ability to store large amounts of energy across a constant temperature or very small temperature range. Furthermore, previous studies on PCM building envelopes evaluated products that may only be incorporated as part of new construction and are not easily applicable to existing, energy-intensive buildings. In this work, we leverage laboratory PCM characterization and whole-building energy simulation to study the energy and cost savings of PCM plaster/paste coatings, which can be applied post construction to both new builds and retrofits of existing buildings (about 40% of residential buildings in the United States fall into the retrofit category). We evaluated the energy impact of PCM plaster/paste composites for a single-family residential building in the United States, including layer design (location and thickness), composite properties (phase change temperature, energy density, and shape of the enthalpy curve), and U.S. climate zone. The enthalpy curve shape of PCM shows that phase change temperature and energy density are not the only two parameters that must be considered for PCM selection. Maximizing the energy density amid the effective TES zone is key to boosting energy savings. We also studied PCM price targets with the aim of achieving reasonable payback periods based on both block and time-of-use electricity rates. Moreover, we developed an empirical equation to provide a rough estimate of the energy savings potential of incorporating PCM without the need to perform detailed simulations. These results will help guide the selection and design of PCM plaster/paste composite elements for residential building envelopes.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗
DOE OSTI2021

Tuning Surface Stoichiometry of SOFC Electrodes at the Molecular and Nano-scale for Enhanced Performance and Durability

This project achieved the following objectives. Different cation segregation behaviors of different common SOFC cathodes, including La 0.6 Sr 0.4 Co0.2Fe 0.8 O 3-δ (LSCF), Sr 0.5 Sm 0.5 O 3-δ (SSC), and PrBa 0.5 Sr 0.5 Co 1.5 Fe 0.5 O5 +δ (PBSCF), were determined. We showed how oxygen partial pressure and gas impurities impact the stability of SOFC cathodes. We developed atomic layer deposition (ALD) coating techniques for electrodes and showed that by introducing different elements and different ALD oxidizers, electrode surface chemistry can be altered, resulting in enhanced oxygen reduction kinetics. In addition, we developed solution infiltration technique to enhance performance and durability of electrodes. Different infiltrates as well as different thermal treatment processes were screened to identify the optimal surface modification process that yields both low impedance and high durability. The modified cathode shows excellent stability and has a low area specific resistance (ASR) of only 0.2 Ωcm 2 at 600 °C after over 2000 hours of operation. Further, we developed ceramic anodes, SrFe(Co,Mo)O 3 (SFCM) and SrFe(Ni,Mo)O 3 (SFNM), and enhanced anode oxidation kinetics by solution infiltration or in situ catalyst exsolution from the ceramic anode surface. The modified anodes showed improved performance in full SOFCs, and the optimized anode modification shows high stability for over 400 hours at 550 °C. Moreover, the modified anode also demonstrates high durability in methane. This work provides fundamental understanding of electrode surface chemistry and demonstrates a simple, facile, cost-effective approach to enhance catalytic activity and durability of SOFC electrodes.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Dry Printing Pure Copper with High Conductivity and Adhesion for Flexible Electronics

Additive manufacturing of functional devices on various rigid and flexible substrates is rising rapidly due to their design flexibility, rapid manufacturing, and lower cost. Current printing technologies are ink-based and focused on printing silver (Ag) as conductive lines due to its matured ink formulation process, low sintering temperature, ease of printing, and low oxidation rate. However, Ag is the 68th most abundant element on Earth, while copper (Cu) is the 25th, making it much cheaper (>100×) while having a comparable conductivity to Ag. Therefore, printing Cu has become technologically and economically more attractive than Ag. Nevertheless, Cu printing is still a significant challenge in ink-based printing methods due to the higher sintering temperature relative to the glass-transition temperature of most flexible substrates, the higher oxidation rate, the challenging ink formulation process, and ink stability concerns. Here, we demonstrate printing highly conductive Cu on flexible polyimide substrates using a dry printing technique. Cu nanoparticles (~3–30 nm) are generated by on-demand laser ablation of a solid Cu target inside the printer head and under argon background gas. These Cu nanoparticles are then transported through a nozzle and onto the substrate, where they are laser-sintered in real time. The argon gas plays three critical roles in laser plume condensation for nanoparticle generation, transport, and sheath gas to avoid oxidation during sintering. The sintered nanoparticles thus show high electrical conductivity and mechanical stability under static and cyclic tests. Our dry printing technique can potentially revolutionize how electronic devices and sensors are additively manufactured for earth and space applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Reimagining the $e_g$ 1 Electronic State in Oxygen Evolution Catalysis: Oxidation-State-Modulated Superlattices as a New Type of Heterostructure for Maximizing Catalysis

We report that the discovery of solid-phase, inexpensive transition-metal-based water oxidation catalysts is a central goal for renewable energy, and has led to a general consensus that a partially populated metal e g d-electronic state is desirable, leading to favorable catalysis for certain elements in specific oxidation states. In manganese systems, the key species is manganese(III), whose high-spin d 4 electronic configuration places an unpaired electron in the e g orbital, which is postulated to contribute to electronic and structural features that support catalysis. Based on density functional theory calculations, it is predicted that electron transfer would be facilitated by a catalyst with alternating low- and high-Mn III -content sheets, which positions neighboring band edges in closer energetic proximity. The preparation of such catalysts is demonstrated for the first time and it is shown that the catalytic activity is maximized in these systems over more uniform, but more Mn III -rich systems. The best catalyst possesses alternating high-and low-average oxidation state sheets with interlayer Cs + ions, and has an overpotential of 450 mV at 10 mA, which represents an improvement of 250 mV over the best unmodified synthetic potassium birnessites. Using scanning tunneling spectroscopy, bandgap modulations consistent with the theoretically predicted band edge shifts are detected.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Behavioral simulations and experimental evaluations of stress induced spatial nonuniformity of dynamic bulk modulus in additive friction stir deposited AA 6061

Additive friction stir deposition (AFSD) is a rapidly developing solid-state additive manufacturing (AM) technology that enables the fabrication of customized products on a relatively large scale. The unique forge-liked process offers high quality products with refined equiaxed microstructure and exceptional mechanical performance. However, in AFSD, the spatially distributed mechanical properties within a deposited layer have not been established so far, due to the lack of a suitable large-scale mapping method. In the present work, an ultrasonic dynamic-elasticity mapping method was employed to map the distribution of physical properties in a AFSD 6061 Al. Strong spatial asymmetries in elastographies were mainly due to the residual stresses. The origin of the asymmetries was investigated through thermo-mechanical simulations of the AFSD process. It was observed that majority of the asymmetries were associated with the mechanical residual stresses instead of the symmetric thermal residual stresses during linear deposition of the AFSD process. However, the thermal residual stresses can be manipulated to become asymmetric with a 90° turn in the linear deposition path, due to the difference between the levels of cooling along the edges of the inner and outer corners. Hence, the mechanical and thermo-mechanical residual stresses can be additive or subtractive depending on the direction of the turns. Here, such numerically predicted behaviors were also experimentally observed on the AFSD fabricated samples by ultrasonic elastography. Furthermore, additional preliminary studies on multi-layer AFSD fabrications show the asymmetric mechanical stresses generated during the deposition process on different layers generate constructive or destructive interference which results to spatially variable dynamic bulk modulus depending on the deposition orientations of layers.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electrochemical Proton Insertion Modulates the Hydrogen Evolution Reaction on Tungsten Oxides

Development of new electrocatalysts for the hydrogen evolution reaction (HER) could reduce dependence on Pt and other rare metals and enable large-scale production of hydrogen with near-zero carbon emissions. Mechanistic insight into the electrocatalytic activity of a material helps to accelerate the development of new electrocatalysts. Alternative electrocatalyst materials such as transition metal oxides and sulfides can undergo insertion reactions that change their properties. Recent reports indicate that the presence of inserted ions can influence electrocatalytic activity. In this work, we utilized a materials chemistry approach to understand the role of proton insertion on the HER activity of layered tungsten oxide hydrates (WO 3 ∙xH 2 O, x = 1, 2). We synthesized a series of tungsten oxide hydrates along with an octylamine-pillared tungsten oxide (OA-WO 3 ). We used cyclic voltammetry to study the electrochemical reactivity of each material and performed ex situ X-ray diffraction and Raman spectroscopy to understand bulk and surface structural changes during electrochemical cycling. We show an inverse relationship between the degree of proton insertion and HER overpotential in tungsten oxides: the lack of proton insertion leads to a high overpotential for the HER. We discuss three hypotheses for how proton insertion leads to HER activity in WO 3 ∙xH 2 O: 1) proton insertion changes the electronic band structure of WO 3 ∙xH 2 O, 2) the presence of bulk protons can influence ΔG H,ads at the surface sites, and 3) inserted protons may participate in the HER mechanism on WO 3 ∙xH 2 O. Overall, this work shows the critical role of proton insertion in enabling high HER activity in tungsten oxides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

ZnTiN 2 as an Electron-Selective, Protective Layer on Si Photocathodes

Photoelectrochemical production of fuels requires photoelectrodes that efficiently convert sunlight to electrochemical energy by producing photovoltage and photocurrent and maintain this ability over time under a variety of pH, illumination, and applied bias conditions. Work in the photovoltaic community has demonstrated that interfaces with high charge carrier selectivity provide high photovoltages. This offers a co-design opportunity to create semiconductor photoelectrodes with contact layers that are both carrier-selective and offer protection from degradation in aqueous solutions. In this work, we explored the ternary nitride ZnTiN 2 as an electronselective, protective layer for Si-based photocathodes. We demonstrated that ZnTiN 2 formed a heterojunction with p-type Si that facilitated electron movement toward the ZnTiN 2 surface for light-driven reduction reactions. Across a variety of electrolyte conditions, ZnTiN 2 /Si produced an open circuit voltage of ca. 400 mV vs the solution potential, while bare Si produced 220−480 mV vs the solution potential depending on conditions. ZnTiN 2 was also shown to protect Si over 72 h at open circuit in the dark in 0.1 M KHCO 3 aqueous solution at pH 10.5, with a 2.4% loss in open circuit voltage compared to a 17% loss for unprotected Si. A protective effect was also observed under illumination during methyl viologen reduction at pH 3.5 for 21 h, with a 2.5% loss in open circuit voltage observed for ZnTiN 2 /Si compared to a 25% loss in open circuit voltage for unprotected Si under the same conditions. Elemental characterization revealed the presence of oxides on the surface of ZnTiN 2 that are consistent with the Pourbaix diagram after photoelectrochemical operation; these oxides appeared to support durability without hindering charge carrier extraction to drive electrochemical work. This work highlights the promise of ZnTiN 2 for durable photoelectrochemical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Reduced order modeling for flow and transport problems with Barlow Twins self-supervised learning

Abstract We propose a unified data-driven reduced order model (ROM) that bridges the performance gap between linear and nonlinear manifold approaches. Deep learning ROM (DL-ROM) using deep-convolutional autoencoders (DC–AE) has been shown to capture nonlinear solution manifolds but fails to perform adequately when linear subspace approaches such as proper orthogonal decomposition (POD) would be optimal. Besides, most DL-ROM models rely on convolutional layers, which might limit its application to only a structured mesh. The proposed framework in this study relies on the combination of an autoencoder (AE) and Barlow Twins (BT) self-supervised learning, where BT maximizes the information content of the embedding with the latent space through a joint embedding architecture. Through a series of benchmark problems of natural convection in porous media, BT–AE performs better than the previous DL-ROM framework by providing comparable results to POD-based approaches for problems where the solution lies within a linear subspace as well as DL-ROM autoencoder-based techniques where the solution lies on a nonlinear manifold; consequently, bridges the gap between linear and nonlinear reduced manifolds. We illustrate that a proficient construction of the latent space is key to achieving these results, enabling us to map these latent spaces using regression models. The proposed framework achieves a relative error of 2% on average and 12% in the worst-case scenario (i.e., the training data is small, but the parameter space is large.). We also show that our framework provides a speed-up of $$7 \times 10^{6}$$ 7 × 10 6 times, in the best case, and $$7 \times 10^{3}$$ 7 × 10 3 times on average compared to a finite element solver. Furthermore, this BT–AE framework can operate on unstructured meshes, which provides flexibility in its application to standard numerical solvers, on-site measurements, experimental data, or a combination of these sources.

97 MATHEMATICS AND COMPUTING↗