SEARCH · Engineering Papers

Results for “large displacement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1978

High-velocity gas in the jet in the radio galaxy DA 240

Spectrograms of the radio galaxy identified with the source DA 240, obtained with the Kitt Peak 4-m telescope and Ritchey-Chretien spectrograph, reveal the presence of ionized gas in the jet discovered earlier. This gas has a large negative velocity displacement of 3400 km/s relative to the center of the galaxy. This is further evidence for the ejection of gas in a violent event in the nucleus of a radio galaxy. The velocity gradient in this gas is less than about 50 km/s over 14 kpc.

Burbidge, E. M.↗

NASA NTRS1986

Measure of displacement around holes in composite plates subjected to quasi-static compression

Contour maps of thickness changes were obtained for three quasi-isotropic graphite-epoxy plates with central holes, loaded in compression. Thickness changes were determined for six load increments from nearly zero to within a few percent of the failure load. The largest change of thickness occurred near the hole but not at the boundary of the hole. Below 90 percent of the failure load, the thickness changes were nearly proportional to load. Irregularities of thickness changes occurred in zones of compressive stresses and they were attributed to localized fiber buckling. A new optical technique was developed to measure thickness changes with high sensitivity. It utilizes a comparatively simple means of holographic interferometry on both sides of the specimen, followed by additive moire to obtain thickness changes as the sum of the out-of-plane displacements. Sensitivity was 12.5 x 10 to the -6 power in. per fringe order. The fringe patterns represent thickness changes uniquely, even when specimen warpage and consequent out-of-plane displacements are very large.

Duke, J. C., Jr.↗

NASA NTRS1986

Analyses of spacecraft polymeric materials

Partial analytical characterizations are made by four different techniques of three polymeric materials used in conjunction with the Space Telescope for samples flown on mission STS-8. The polymers were Tedlar, Kapton H, and Kapton F. The surfaces of the three polymers were attacked and oxidized by atomic oxygen, and fluorine is lost from the surface of Kapton F, largely due to displacement by atomic oxygen.

Worley, S. D.↗

NASA NTRS1996

Laser Sources for Generation of Ultrasound

Two laser systems have been built and used to demonstrate enhancements beyond current technology used for laser-based generation and detection of ultrasound. The first system consisted of ten Nd:YAG laser cavities coupled electronically and optically to permit sequential bursts of up to ten laser pulses directed either at a single point or configured into a phased array of sources. Significant enhancements in overall signal-to-noise ratio for laser ultrasound incorporating this new source system was demonstrated, using it first as a source of narrowband ultrasound and secondly as a phased array source producing large enhanced signal displacements. A second laser system was implemented using ultra fast optical pulses from a Ti:Sapphire laser to study a new method for making laser generated ultrasonic measurements of thin films with thicknesses on the order of hundreds of angstroms. Work by prior investigators showed that such measurements could be made based upon fluctuations in the reflectivity of thin films when they are stressed by an arriving elastic pulse. Research performed using equipment purchased under this program showed that a pulsed interferometric system could be used as well as a piezoreflective detection system to measure pulse arrivals even in thin films with very low piezoreflective coefficients.

Wagner, James W.↗

NASA NTRS2003

Umbilical Stiffness Matrix Characterization and Testing for Microgravity Science Payloads

This paper describes efforts of testing and analysis of various candidate cables and umbilicals for International Space Station microgravity science payloads. The effects of looping, large vs. small displacements, and umbilical mounting configurations were assessed. A 3-DOF stepper motor driven fixture was used to excite the umbilicals. Forces and moments were directly measured in all three axes with a 6-DOF load cell in order to derive suitable stiffness matrices for design and analysis of vibration isolation controllers. Data obtained from these tests were used to help determine the optimum type and configuration of umbilical cables for the International Space Station microgravity science glovebox (MSG) vibration isolation platform. The data and procedures can also be implemented into control algorithm simulations to assist in validation of actively controlled vibration isolation systems. The experimental results of this work are specific in support of the Glovebox Integrated Microgravity Isolation Technology (g-LIMIT) isolation platform, to be located in the microgravity science glovebox aboard the U.S. Destiny Laboratory Module.

Engberg, Robert C.↗

NASA NTRS2012

Photogrammetry Measurements During a Tanking Test on the Space Shuttle External Tank, ET-137

On November 5, 2010, a significant foam liberation threat was observed as the Space Shuttle STS-133 launch effort was scrubbed because of a hydrogen leak at the ground umbilical carrier plate. Further investigation revealed the presence of multiple cracks at the tops of stringers in the intertank region of the Space Shuttle External Tank. As part of an instrumented tanking test conducted on December 17, 2010, a three dimensional digital image correlation photogrammetry system was used to measure radial deflections and overall deformations of a section of the intertank region. This paper will describe the experimental challenges that were overcome in order to implement the photogrammetry measurements for the tanking test in support of STS-133. The technique consisted of configuring and installing two pairs of custom stereo camera bars containing calibrated cameras on the 215-ft level of the fixed service structure of Launch Pad 39-A. The cameras were remotely operated from the Launch Control Center 3.5 miles away during the 8 hour duration test, which began before sunrise and lasted through sunset. The complete deformation time history was successfully computed from the acquired images and would prove to play a crucial role in the computer modeling validation efforts supporting the successful completion of the root cause analysis of the cracked stringer problem by the Space Shuttle Program. The resulting data generated included full field fringe plots, data extraction time history analysis, section line spatial analyses and differential stringer peak ]valley motion. Some of the sample results are included with discussion. The resulting data showed that new stringer crack formation did not occur for the panel examined, and that large amounts of displacement in the external tank occurred because of the loads derived from its filling. The measurements acquired were also used to validate computer modeling efforts completed by NASA Marshall Space Flight Center (MSFC).

Littell, Justin D.↗

NASA NTRSDate not supplied

Buckling Behavior of Conical-Cylindrical Shells and Design Considerations for Launch-Vehicle Applications

Traditionally, launch vehicles are constructed with a series of buckling-prone thin-walled cylindrical and conical shells, in which the buckling behavior of these shells has been well studied and buckling design guidance exists. Conical-cylindrical shell geometry is now being utilized for launch-vehicle stage adapters and payload adapters due to advances in manufacturing and numerical techniques, but there is no available buckling design guidance for this nontraditional combined geometry. In order to provide design recommendations, the buckling behavior and imperfection sensitivity of conical-cylindrical shells and how it differs from the conical and cylindrical components needs to be better understood. From this premise, it is possible to investigate whether or not the buckling knockdown factor guidelines for conical and cylindrical shells outlined in NASA SP-8019 and NASA SP-8007, respectively, are still applicable. The results in this paper will show that the current recommendations are not appropriate in some cases. In addition, it was observed that the large rotations and displacements near the transition between the cone and cylinder can have a larger effect on the buckling load than the presence of radial imperfections for conical-cylindrical shells, which is different than conical and cylindrical shells. More interesting is the fact that design modifications to increase the buckling capability of a conical-cylindrical shell such as adding reinforcement, which may add mass, will make the shell more sensitive to imperfections. The increased imperfection sensitivity may negate the increase in buckling capability that was thought to be achievable. In the end, it may be more beneficial to design a conical-cylindrical shell in which the buckling behavior is dominated by the more predictable geometric nonlinearity, which may lead to an overall lower buckling load, but a lower knockdown factor may be possible since it will not be as sensitive to the less-known radial imperfections.

Buckling↗

NASA NTRS1990

Measurement of structure motion by means of a moving light sheet

The elaboration of an optical system which measures the displacement and velocity of large flexible space structures is reviewed. The motion-measuring system, comprised of a laser, optics, motorized mirror, two photodiodes and electronics, is designed to allow feedback for configuration control of flexible structures. A motor or scanner is employed to sweep the light sheet. The range of motion was shown to be 2 inches, and information was received at a rate of 30 Hz. The uncertainty in displacement measurement was better than +0.01 inch from a distance of 16 feet. The results are considered to be very good for two scanning light sheet systems. Higher sample rates and a more constant speed would improve the rotating mirror option, and the accuracy and range of the scanning mirror option could be upgraded as well. Both setups are shown to be viable noncontact measuring methods for the displacement and velocity of large space structures.

Tcheng, Ping↗

NASA NTRS1999

Sensitivity of Lumped Constraints Using the Adjoint Method

Adjoint sensitivity calculation of stress, buckling and displacement constraints may be much less expensive than direct sensitivity calculation when the number of load cases is large. Adjoint stress and displacement sensitivities are available in the literature. Expressions for local buckling sensitivity of isotropic plate elements are derived in this study. Computational efficiency of the adjoint method is sensitive to the number of constraints and, therefore, the method benefits from constraint lumping. A continuum version of the Kreisselmeier-Steinhauser (KS) function is chosen to lump constraints. The adjoint and direct methods are compared for three examples: a truss structure, a simple HSCT wing model, and a large HSCT model. These sensitivity derivatives are then used in optimization.

Akgun, Mehmet A.↗

NASA NTRS1995

The Elastic Response of the Earth to Interannual Variations in Antarctic Precipitation

Measurements of elastic displacements of the bedrock surrounding large ice sheets have been proposed as a means to detect mass changes in these ice sheets. However, accumulation of glacial mass on the ice sheets is a noisy process, subject to large spatial and temporal variations in precipitation. We simulated the response of the Antarctic continent to a stochastic model of interannual precipitation variations and found that interannual variations in the elastic response of the earth are large when compared to the long-term mean of displacements produced by an assumed average ice mass imbalance of 10%. If, as some scientists predict, Antarctic ice mass changes in the future become dramatic, the long-term signal should be large enough to be detected by a few years of geodetic measurements, despite climatic noise.

Hager, Bradford H.↗

NASA NTRS2020

U.S. Coast Guard Boat Recovery Simulation at the NASA Ames Vertical Motion Simulator

The U.S. Coast Guard routinely uses the Over-The-Horizon (OTH-IV), a cutter deployed, rigid-hulled inflatable boat for rescue and law enforcement operations. The term "cutter" refers to a Coast Guard vessel 65 feet in length or greater with accommodations for crew to live aboard and the ability to deploy smaller boats including the OTH-IV. A deployment method employed by some cutter class vessels is a davit crane system and specialized hook mechanism to connect the smaller boat. The launch and recovery operation requires several crewmembers, where one is tasked with releasing and connecting the hook to the small boat. Manipulating the hook can pose a risk to the crewmember depending on sea conditions combined with fatigue level or task expertise. Equipment and crewmembers are tested extensively due to the inherent risk of the task, but the sea conditions cannot be controlled. To address the sea condition variable, the U.S. Coast Guard and NASA leveraged the Vertical Motion Simulator (VMS) as a platform to test new equipment or train crewmembers in varying sea conditions. With 6 degrees of freedom and a vertical displacement of +/- 22ft, the VMS is capable of simulating conditions up to sea-state 5. The proof of concept experiment took place in September 2018 and demonstrated that the VMS can accurately simulate varying sea-states, collect performance data, and design a reliable and safe system for participants. The U.S. Coast Guard provided boat displacement data from the Large Amplitude Motion Program (LAMP). The program generates multi-directional waves with a cosine squared spreading function which produced a time history response of displacement data (surge, sway, heave, roll, pitch, yaw) of the OTH-IV's center of gravity (C.G). The displacement data was differentiated into acceleration evaluated at the crewmember's position at the front (bow) of the boat. Those accelerations were transformed to the VMS coordinate system and used as command inputs to the motion system's washout filters. The VMS uses Interchangeable Cabs (ICab) to perform flight simulations on a variety of aircraft or spacecraft configurations. An ICab typically contains seats, restraints, pilot controls, instrument panel, and out-the-window projectors all enclosed in a familiar cockpit configuration. To replicate the launch and recovery of a small boat, all the conventional features of a flight simulator and canopy were removed to be replaced with a to-scale OTH-IV bow mockup. The bow section was constructed from aluminum, and a connection point known as the davit ring. Additionally, a hook replica was suspended by a cable from the ceiling as if it were hanging from a davit crane aboard a cutter vessel. The last step was providing an auxiliary control to close the distance between suspended hook and the davit ring on the bow mockup. Without control the boat would simulate the wave motion, but with no guarantee that the crewmember will be in reach of the hook. Since the wave motion was repeatable, an additional acceleration command sent to the washout filters to move the simulator in the surge, sway, and heave directions, independently. The commands were rate limited such that the additional movement was not detectable with respect to the wave motion. The results showed that for each wave profile, a unique set of acceleration commands provided opportunities for crewmembers to gain control of the hook and connect it to the davit ring.

Riccobono, Nicholas S.↗

NASA NTRS1986

Wind-driven surface transport in stratified closed basins Direct versus residual circulations

The wind-driven circulation in a moderately large, stratified basin Lake Tahoe, California-Nevada, is studied using a numerical model. Direct circulations, in which the current directions remain relatively constant and the mean circulation formed over several days resembles the instantaneous circulation, and residual circulations, in which the currents fluctuate continuously and the mean circulation is characterized by small net displacements of parcels after large oscillations, are found. The lake's double gyre, dominated by the large anticyclonic northern gyre, differs from the single cyclonic gyre reported for other stratified basins, and examination of the modeled vorticity budget in the surface layer shows that the curl of the wind stress must be included to obtain the observed direct double gyre circulation.

Strub, P. T.↗

NASA NTRS2010

Interlaminar Stresses by Refined Beam Theories and the Sinc Method Based on Interpolation of Highest Derivative

Computation of interlaminar stresses from the higher-order shear and normal deformable beam theory and the refined zigzag theory was performed using the Sinc method based on Interpolation of Highest Derivative. The Sinc method based on Interpolation of Highest Derivative was proposed as an efficient method for determining through-the-thickness variations of interlaminar stresses from one- and two-dimensional analysis by integration of the equilibrium equations of three-dimensional elasticity. However, the use of traditional equivalent single layer theories often results in inaccuracies near the boundaries and when the lamina have extremely large differences in material properties. Interlaminar stresses in symmetric cross-ply laminated beams were obtained by solving the higher-order shear and normal deformable beam theory and the refined zigzag theory with the Sinc method based on Interpolation of Highest Derivative. Interlaminar stresses and bending stresses from the present approach were compared with a detailed finite element solution obtained by ABAQUS/Standard. The results illustrate the ease with which the Sinc method based on Interpolation of Highest Derivative can be used to obtain the through-the-thickness distributions of interlaminar stresses from the beam theories. Moreover, the results indicate that the refined zigzag theory is a substantial improvement over the Timoshenko beam theory due to the piecewise continuous displacement field which more accurately represents interlaminar discontinuities in the strain field. The higher-order shear and normal deformable beam theory more accurately captures the interlaminar stresses at the ends of the beam because it allows transverse normal strain. However, the continuous nature of the displacement field requires a large number of monomial terms before the interlaminar stresses are computed as accurately as the refined zigzag theory.

Slemp, Wesley C. H.↗

NASA NTRS1991

New displacement-based methods for optimal truss topology design

Two alternate methods for maximum stiffness truss topology design are presented. The ground structure approach is used, and the problem is formulated in terms of displacements and bar areas. This large, nonconvex optimization problem can be solved by a simultaneous analysis and design approach. Alternatively, an equivalent, unconstrained, and convex problem in the displacements only can be formulated, and this problem can be solved by a nonsmooth, steepest descent algorithm. In both methods, the explicit solving of the equilibrium equations and the assembly of the global stiffness matrix are circumvented. A large number of examples have been studied, showing the attractive features of topology design as well as exposing interesting features of optimal topologies.

Bendsoe, Martin P.↗

NASA NTRS1973

Task 10: an ERTS Experiment for Mapping Iron Compounds, 1383

The author has identified the following significant results. Preliminary results of a spectral ratioing technique are shown for a region at the southern end of the Wind River Range, Wyoming. Digital ratio graymaps and analog ratio images have been produced for the test site, but ground truth is not yet available for thorough interpretation of these products. ERTS-1 analog ratio images were found generally better than either ERTS-1 single channel images or high altitude aerial photos for the discrimination of vegetation from non-vegetation in the test site region. Some linear geological features smaller than the ERTS-1 spatial resolution are seen as well in ERTS-1 ratio and single channel images as in high altitude aerial photography. Geochemical information appears to be extractable from ERTS-1 data. Good preliminary quantitative agreement between ERTS-1 derived ratios and laboratory derived reflectance ratios of rocks and minerals encourage plans to use lab data as training sets for a simple ratio gating logic approach to automatic recognition maps. Empirical atmospheric corrections indicate that atmospheric corrections are needed to make the ratio method, and possibly other types of data processing, consistent over large geographical and temporal displacements.

Vincent, R. K.↗

NASA NTRS1978

An extension of the dual magnetometer method for use on a dual spinning spacecraft

A method of estimating and correcting for the magnetic field of a dual spinning spacecraft has been developed by employing an extension of the dual magnetometer technique of Ness et al. (1971). This new method is useful for those situations in which a magnetometer boom of modest length (7-10 m) is attached to the spinning part of a large spacecraft (800-1000 kg). The purpose of using a dual spinning spacecraft is to accommodate two types of instruments: (1) imaging and similar 'pointed' remote sensing systems on the stationary platform and (2) fields, particles, and other in situ measuring instruments on the spinning portion. Present-day imaging systems are well known to exhibit large magnetic moments, sometimes displaced from the spacecraft center by a significant amount. The new method assumes that the stationary part of the spacecraft possesses a magnetic field which is represented by a combination of a dipole and a quadrupole field.

Lepping, R. P.↗

NASA NTRS1987

Nonlinear beam kinematics by decomposition of the rotation tensor

A simple matrix expression is obtained for the strain components of a beam in which the displacements and rotations are large. The only restrictions are on the magnitudes of the strain and of the local rotation, a newly-identified kinematical quantity. The local rotation is defined as the change of orientation of material elements relative to the change of orientation of the beam reference triad. The vectors and tensors in the theory are resolved along orthogonal triads of base vectors centered along the undeformed and deformed beam reference axes, so Cartesian tensor notation is used. Although a curvilinear coordinate system is natural to the beam problem, the complications usually associated with its use are circumvented. Local rotations appear explicitly in the resulting strain expressions, facilitating the treatment of beams with both open and closed cross sections in applications of the theory. The theory is used to obtain the kinematical relations for coupled bending, torsion, extension, shear deformation, and warping of an initially curved and twisted beam.

Danielson, D. A.↗

NASA NTRS1990

Parallel simulated annealing algorithms for cell placement on hypercube multiprocessors

Two parallel algorithms for standard cell placement using simulated annealing are developed to run on distributed-memory message-passing hypercube multiprocessors. The cells can be mapped in a two-dimensional area of a chip onto processors in an n-dimensional hypercube in two ways, such that both small and large cell exchange and displacement moves can be applied. The computation of the cost function in parallel among all the processors in the hypercube is described, along with a distributed data structure that needs to be stored in the hypercube to support the parallel cost evaluation. A novel tree broadcasting strategy is used extensively for updating cell locations in the parallel environment. A dynamic parallel annealing schedule estimates the errors due to interacting parallel moves and adapts the rate of synchronization automatically. Two novel approaches in controlling error in parallel algorithms are described: heuristic cell coloring and adaptive sequence control.

Banerjee, Prithviraj↗