Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “impacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Impact of low reactivity fuel type on low load combustion, emissions, and cyclic variations of diesel-ignited dual fuel combustion

In this study, cyclic variations in dual fuel combustion with diesel ignition of three different low reactivity fuels (methane, propane, and gasoline) are examined under identical operating conditions. Experiments were performed on a single cylinder research engine (SCRE) at a low load of 3.3 bar brake mean effective pressure (BMEP). The start of injection (SOI) of diesel was varied from 280 to 330 absolute crank angle degrees (CAD). Engine speed, rail pressure, and boost pressure were held constant at 1500 rpm, 500 bar, and 1.5 bar, respectively. The energy substituted by the low reactivity fuel was fixed at 80% of the total energy input. It was found that diesel-methane (DM) and diesel-propane (DP) combustion were affected by diesel mixing to a greater extent than diesel-gasoline (DG) combustion due to the higher reactivity of gasoline. The magnitude of low temperature heat release was greatest for DG combustion followed by DM and DP combustion for all SOIs. The ignition delay for DG combustion was the shortest, followed by DM and DP combustion. DM and DP combustion exhibited more cyclic variations than DG combustion. Cyclic variations decreased for DM and DP combustion when SOI was advanced; however, DG combustion cyclic variations remained essentially constant for all SOIs. Earlier SOIs (280, 290, 300, and 310 CAD) for DM and (280, 290, and 300 CAD) for DP combustion indicated some prior-cycle effects on the combustion and IMEP (i.e. some level of determinism).

Engineering↗
DOE OSTI2022

Experimental study of the impact of scavenging efficiency on diesel combustion in an opposed-piston two-stroke engine

The opposed-piston two-stroke (OP2S) engine is a promising alternative powertrain technology that can offer thermal and brake efficiency improvements over conventional four-stroke engines. In recent years, many of the technical barriers of the OP2S engine architecture have been overcome. However, there is still a need for fundamental studies to provide insight into the scavenging and combustion processes of the OP2S engine to help design and operate the most efficient combustion systems using this engine architecture. This work aims to provide such insights by analyzing experimental data collected on a 3-cylinder, 4.9 L OP2S engine. Specifically, a scavenging efficiency sweep, an engine speed sweep with a constant scavenging efficiency, and an engine speed with a constant pressure differential across the engine were studied in detail. It was found that in diesel combustion, as the scavenging efficiency decreased, the increase in temperature of the hot, internal residuals resulted in a significant increase in heat transfer. Despite lowering pumping losses, this resulted in an overall decrease in brake efficiency. When the bulk thermodynamic conditions of two different scavenging efficiency cases (67% and 72%) were matched at port closing, the lower scavenging efficiency case still displayed a 0.7 percentage point penalty in net thermal efficiency and an increase in engine-out indicated specific emissions of NOx of 18% due to residual stratification in the cylinder. The results presented in this work show that the optimal breathing strategy in diesel combustion on an OP2S engine architecture is one that results in a slightly under-scavenged environment at port closing. However, the results did show potential system-level efficiency benefits of decreasing scavenging efficiency, meaning that alternative fuels and combustion strategies without the constraints of diesel combustion could achieve system-level efficiency gains by running significantly under-scavenged.

Engineering↗
DOE OSTI2026

Data for Immediate Impacts of Soybean Cover Crop on Bacterial Community Composition and Diversity in Soil Under Long-Term Saccharum Monoculture

Saccharum yield decline results from long-term monoculture practices. Changes in cropping management can improve soil health and productivity. Below-ground bacterial community diversity and composition across soybean (Glycine max (L.) Merr) cover crop, Saccharum monoculture (30+ year) and fallowed soil were determined. Near full length (~1,400 base pairs) of 16S rRNA gene sequences were extracted from the rhizospheres of sugarcane and soybean and fallowed soil were compared. Higher soil bacterial diversity was observed in the soybean cover crop than sugarcane monoculture across all measured indices (observed operationational taxonomic units, Chao1, Shannon, reciprocal Simpson and Jackknife). Acidocateria, Proteobacteria, Bacteroidetes and Planctomycetes were the most abundant bacterial phyla across the treatments. Indicator species analysis identified nine indicator phyla. Planctomycetes, Armatimonadetes and candidate phylum FBP were associated with soybean; Proteobacteria and Firmicutes were linked with sugarcane and Gemmatimonadetes, Nitrospirae, Rokubacteria and unclassified bacteria were associated with fallowed soil. Non-metric multidimensional scaling analysis showed distinct groupings of bacterial operational taxonomic units (97% identity) according to management system (soybean, sugarcane or fallow) indicating compositional differences among treatments. This is confirmed by the results of the multi-response permutation procedures (A = 0.541, p = 0.00045716). No correlation between soil parameters and bacterial community structure was observed according to Mantel test (r = 211865, p = 0.14). Use of soybean cover-crop fostered bacterial diversity and altered community structure. This indicates cover crops could have a restorative effect and potentially promote sustainability in long-term Saccharum production systems.

Field Data↗
DOE OSTI2026

Data for Impact of Vertical and Seasonal Variation in Leaf Traits on Simulating Soybean Canopy Photosynthesis via 1D and 3D Modeling

Accurate modeling of photosynthesis is crucial for predicting crop productivity and quantifying the carbon cycle in agroecosystems. Leaf traits are essential inputs for modeling canopy photosynthesis. Yet, many existing models still use fixed plant functional type (PTF)-based values to parameterize leaf traits under a big-leaf or two-big-leaf assumption, neglecting their vertical profiles and seasonal changes. This simplification may introduce significant uncertainties in estimating gross primary productivity (GPP). In this study, we simulated soybean GPP and tested the effects of vertical and seasonal variation in three key leaf photosynthetic traits: the maximum carboxylation rate at 25 °C (Vcmax25), leaf chlorophyll content (LCC), and leaf mass per area (LMA) in the 1D-SCOPE and 3D-Helios models. Weekly field measurements were conducted during the growing season of 2024 to support the simulation. We designed ten leaf trait parameterization schemes by incorporating different combinations of vertical profiles and seasonal changes, while assuming homogeneous canopy architecture in both models. Our results revealed that Vcmax25 vertical and seasonal variation had the strongest influence on simulated GPP in both 1D and 3D models, while LCC and LMA effects were minimal. Particularly, the scheme with an empirically parameterized Vcmax25 profile achieved comparable performance to the scheme with the measured Vcmax25 profile. Both 1D-SCOPE and 3D-Helios accurately modeled GPP (SCOPE: R2 = 0.87, Bias = 0.55 µmol m⁻² s⁻¹; Helios: R2 = 0.9, Bias = 0.22 µmol m⁻² s⁻¹) under the most complex scheme, and their responses to vertical and seasonal variation in leaf traits were consistent, demonstrating the robustness of our findings. Based on our findings, we propose a scalable framework for parameterizing leaf traits to improve GPP simulations. This study contributes to improving the representation of leaf trait dynamics in canopy-level photosynthesis models, potentially enhancing our ability to predict crop productivity and understand agroecosystem carbon dynamics.

Photosynthesis↗
DOE OSTI2026

Data for Impacts of Legacy and Contemporary Nitrogen Inputs on N2O and CO2 Emissions in Miscanthus and Maize Cultivated Soils

Nutrient inputs influence the sustainability of bioenergy crop production through contemporary (shortly after addition) and legacy effects (persisting over years) on microbial nitrogen (N) and carbon cycling, which contribute to greenhouse gas emissions. However, the relative importance of contemporary and legacy effects and how that could vary by crop functional types is poorly understood. Considering its rhizomatous roots and perennial growth, we hypothesized that Miscanthus × giganteu s ( M × g ) would be more sensitive to legacy N fertilization and the historical context of its environment than an annual crop like maize. To test this hypothesis, we examined the effects of legacy and contemporary N inputs on nitrous oxide (N2O) and carbon dioxide (CO2) emissions, as well as key N cycling genes in soils where M × g and maize were grown. A 150-day soil incubation experiment was conducted using soils from a long-term M × g and maize fertility experiment with three historic N fertilization rates (0, 112, and 336 kg N ha−1 year−1) and a contemporary amendment (60 mg N kg−1) with negative control (0 mg N kg−1). We observed significant increases in cumulative N2O emissions in M × g soils relative to maize soils, particularly at higher legacy fertilization rates, while contemporary N had no significant effect. Bacterial amoA gene abundance, which plays a significant role in nitrification in nutrient-rich soils, also increased with higher legacy fertilization rates in M × g soils but was unaffected by the contemporary N. In maize soils, legacy and contemporary N did not significantly affect N2O emissions, but cumulative CO2 emissions and amoA gene abundance significantly increased. The abundances of norB genes were not significantly influenced by either legacy fertilization or contemporary N amendments in either soil. Our findings demonstrate the greater importance of fertilization history over contemporary N in mediating soil N2O emissions, particularly for perennial bioenergy crops.

Carbon↗
DOE OSTI2020

Photometric Redshifts with the LSST. II. The Impact of Near-infrared and Near-ultraviolet Photometry

Accurate photometric redshift (photo-z) estimates are essential to the cosmological science goals of the Vera C. Rubin Observatory Legacy Survey of Space and Time (LSST). In this work, we use simulated photometry for mock galaxy catalogs to explore how LSST photo-z estimates can be improved by the addition of near-infrared (NIR) and/or ultraviolet (UV) photometry from the Euclid, Wide-Field InfrarRed Survey Telescope (WFIRST), and/or Cosmological Advanced Survey Telescope for Optical and ultraviolet Research (CASTOR) space telescopes. Generally, we find that deeper optical photometry can reduce the standard deviation of the photo-z estimates more than adding NIR or UV filters but that additional filters are the only way to significantly lower the fraction of galaxies with catastrophically under- or overestimated photo-z. For Euclid, we find that the addition of JH 5σ photometric detections can reduce the standard deviation for galaxies with z > 1 (z > 0.3) by ∼20% (∼10%), and the fraction of outliers by ∼40% (∼25%). For WFIRST, we show how the addition of deep YJHK photometry could reduce the standard deviation by ≳50% at z > 1.5 and drastically reduce the fraction of outliers to just ∼2% overall. For CASTOR, we find that the addition of its UV- and u-band photometry could reduce the standard deviation by ∼30% and the fraction of outliers by ∼50% for galaxies with z < 0.5. We also evaluate the photo-z results within sky areas that overlap with both the NIR and UV surveys and when spectroscopic training sets built from the surveys’ small-area deep fields are used.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Impact of Rheology Models on Horizontal Well Polymer Flooding in a Heavy Oil Reservoir on Alaska North Slope: A Simulation Study

Polymer rheology can have either a positive or a negative effect on polymer flooding performance under varied circumstances. Many researchers have studied the effect of polymer rheology in a vertical well, but no field scale studies have been conducted to investigate whether polymer rheology is beneficial to polymer flooding in heavy oil reservoirs developed by horizontal wells. In this paper, we conducted a numerical simulation study to examine the effect of HPAM polymer rheology on a polymer flooding pilot, which is the first-ever project conducted on a heavy oil reservoir from Alaska North Slope (ANS) developed by horizontal wells. Three rheology types were considered in the study including the apparent viscosity measured during coreflooding of using a HPAM polymer, the bulk viscosity measured with a viscometer, and a Newtonian flow model. The results suggest that using the bulk viscosity in simulation underestimates the conformance control and the water-oil-ratio reduction capability of the HPAM polymer solution. When the apparent viscosity is used, the incremental oil and sweep were largely increased, and the optimal recovery period of polymer flooding was extended greatly, especially for the heterogeneous formations. Therefore, the rheology type of polymer plays a significant role in the incremental oil recovery and injection profile of the horizontal well system given the pilot test conditions. This study has provided practical guidance to field operators for the ongoing polymer flooding pilot on ANS and will also provide valuable information for other polymer projects conducted in similar conditions.

Leng, Jianqiao↗
DOE OSTI2020

Hypervelocity impact flash expansion geometry under various spacecraft surface electrical conditions

A more congested space environment due to increasing space activities introduces new threats to spacecraft operators. Among these threats include hypervelocity impacts from microparticles (< 1 µg) in the form of meteoroids and space debris. These microparticles travel at speeds between 11.2 and 72.8 km/s with respect to the Earth and can impact spacecraft forming a small (~1 µm) and dense (~ 10 26 m -3 ) plasma. This plasma can generate a strong optical emission (impact flash) and a radio frequency (RF) emission. These emissions can lead to spacecraft electrical anomalies when the impacted spacecraft surface (target) carries high electrical potential due to various space weather effects. To understand the microparticle hypervelocity impact plasma and its associated threat to spacecraft electronics, we studied the hypervelocity impact flash expansion geometry under various spacecraft surface electrical conditions. Three high-speed broadband photomultiplier tubes (PMT) are used to capture the temporal evolution of the impact flash and the temporal evolution of the angular distribution of the impact flash expansion geometry in a 3 MV electrostatic dust accelerator during a ground-based experiment. Overall, results indicate that the impact surface electrical condition has a statistically significant influence on the impact flash geometry, and a strong similarity between the impact plasma and flash expansion geometry. Thus, this paper provides new experimental support for the impact flash origin from and connection with the impact plasma, and serves as the first impact flash expansion geometry characterization under various impact surface electrical conditions in a collisionless environment (< 10 -5 Torr).

42 ENGINEERING↗
DOE OSTI2020

Algebraic expressions for estimating the impact depths of a surface barrier over a homogeneous soil

Engineered surface barriers are used to isolate subsurface contaminants for effective long-term containment of municipal solid waste, other nonhazardous solid and liquid waste, hazardous and toxic wastes, and radioactive waste. The impact depths of a surface barrier are affected by the pre-barrier recharge rate and the properties of the soil beneath the barrier. In this paper, the pore-size-specific (PSS) water velocity is defined and an algebraic expression of PSS velocity is derived based on the stream tube concept and the Brooks and Corey hydraulic retention model. Algebraic expressions are developed to estimate drainage velocities and barrier impact depths after the emplacement of a surface barrier. Four impact depth terms are used to convey the protective effect: drainage front, average drainage, the location with 50% impact, and drainage tail. The drainage front depth is the deepest point at which the barrier has a detectable impact at a specific time (also called the near zero-impact depth). The average-impact depth is the depth at which average drainage occurs. At the 50% impact depth, the water flux rate is reduced by half because of the surface barrier. Lastly, the drainage tail depth (also called the full-impact depth) is the deepest depth at which the water conditions above it are in equilibrium with the barrier. The algebraic expressions show that the average-impact depth is no more than 1/3 of near zero-impact depth, while the 50% impact depth is slightly larger than 1/2 of the near zero-impact depth. The full-impact depth, depending on the final recharge rate from the surface barrier, is usually much smaller than the other impact depths. These differences lead to a very large transition zone beneath a surface barrier. Numerical simulations were conducted to replicate the same conditions. The numerical results corroborated the analytical models by predicting very similar water content profiles and near zero-, average-, 50%, and full-impact depths. The algebraic expressions provided in this paper are useful for quickly identifying sites where the depth of the existing contaminants could be beyond the protection of a surface barrier.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

On the attribution of the impacts of extreme weather events to anthropogenic climate change

Investigations into the role of anthropogenic climate change in extreme weather events are now starting to extend into analysis of anthropogenic impacts on non-climate (e.g. socio-economic) systems. However, care needs to be taken when making this extension, because methodological choices regarding extreme weather attribution can become crucial when considering the events’ impacts. The fraction of attributable risk (FAR) method, useful in extreme weather attribution research, has a very specific interpretation concerning a class of events, and there is potential to misinterpret results from weather event analyses as being applicable to specific events and their impact outcomes. Using two case studies of meteorological extremes and their impacts, we argue that FAR is not generally appropriate when estimating the magnitude of the anthropogenic signal behind a specific impact. Attribution assessments on impacts should always be carried out in addition to assessment of the associated meteorological event, since it cannot be assumed that the anthropogenic signal behind the weather is equivalent to the signal behind the impact because of lags and nonlinearities in the processes through which the impact system reacts to weather. Whilst there are situations where employing FAR to understand the climate change signal behind a class of impacts is useful (e.g. ‘system breaking’ events), more useful results will generally be produced if attribution questions on specific impacts are reframed to focus on changes in the impact return value and magnitude across large samples of factual and counterfactual climate model and impact simulations. We advocate for constant interdisciplinary collaboration as essential for effective and robust impact attribution assessments.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Effects of Impact and Target Parameters on the Results of a Kinetic Impactor: Predictions for the Double Asteroid Redirection Test (DART) Mission

Abstract The Double Asteroid Redirection Test (DART) spacecraft will impact into the asteroid Dimorphos on 2022 September 26 as a test of the kinetic impactor technique for planetary defense. The efficiency of the deflection following a kinetic impactor can be represented using the momentum enhancement factor, β , which is dependent on factors such as impact geometry and the specific target material properties. Currently, very little is known about Dimorphos and its material properties, which introduces uncertainty in the results of the deflection efficiency observables, including crater formation, ejecta distribution, and β . The DART Impact Modeling Working Group (IWG) is responsible for using impact simulations to better understand the results of the DART impact. Pre-impact simulation studies also provide considerable insight into how different properties and impact scenarios affect momentum enhancement following a kinetic impact. This insight provides a basis for predicting the effects of the DART impact and the first understanding of how to interpret results following the encounter. Following the DART impact, the knowledge gained from these studies will inform the initial simulations that will recreate the impact conditions, including providing estimates for potential material properties of Dimorphos and β resulting from DART’s impact. This paper summarizes, at a high level, what has been learned from the IWG simulations and experiments in preparation for the DART impact. While unknown, estimates for reasonable potential material properties of Dimorphos provide predictions for β of 1–5, depending on end-member cases in the strength regime.

58 GEOSCIENCES↗
DOE OSTI2024

A model for oblique impacts on material surfaces

Many practical situations of material damage, wear, and erosion involve collisions between small particles and surfaces at inclined angles. While there are many well-validated models of normal incidence impact situations, elastic-plastic models for oblique incidence impact events are lacking. Here the finite element method is used to predict the normal and tangential coefficient of restitution in oblique impacts for hard, elastic spheres impacting an elastic-perfectly plastic material surface. The proposed model covers various impact angles ranging from 0° to 45°, within a limiting impact velocity below which the effects of heating are negligible. The normal coefficient of restitution follows power-laws with respect to normalized values of the impact velocity. Interestingly, the tangential coefficient of restitution follows a linear relationship with impact velocity. Together, these results provide a semi-empirical set of equations predicting oblique impact rebounds (both velocity and trajectory) for a wide range of conditions and material properties, with which experimental results can be rapidly interpreted. As a result, Laser-Induced Particle Impact Test (LIPIT) data are also presented for aluminum particles impacting aluminum substrates, at impact angles of 25° and 40°; the results compare favorably with the model and validate the general use of such models for the analysis of experimental data.

Coefficient of restitution↗
DOE OSTI2025

Environmental Impacts of Closed-Loop Pumped Storage Hydropower

The goal of this report is to help license applicants, resource agencies, and other members of the hydropower community involved in closed-loop pumped storage hydropower permitting and licensing process, focus the scope of environmental reviews, and more quickly identify impacts with project nexus and potential mitigation measures for these impacts. Pumped storage hydropower (PSH) is an energy storage technology that uses energy to pump water up from a lower reservoir to an upper reservoir where water is stored until electricity is needed and the water is released to a lower reservoir passing through turbines. Closed-loop PSH—PSH that is not continuously connected to a naturally flowing water feature—is one of the lowest greenhouse gas emitting energy storage technologies and is therefore a critical part of the transition to renewable energy (Simon et al. 2023). Proposals for closed-loop PSH facilities in the United States currently account for more than 40% of original licenses and 99% of potential generation capacity in the Federal Energy Regulatory Commission (FERC) hydropower licensing pipeline (Johnson et al. 2023). While closed-loop PSH facilities can have lower environmental impacts than open-loop PSH facilities, no closed-loop facilities have been constructed in the United States to enable direct accounting of project impacts and efficacy of mitigations. Many proposals for closed-loop PSH submitted to FERC are abandoned early in the permitting and licensing process prior to license applications and environmental assessments, so there is little documentation describing potential project impacts and proposed mitigations. The newness of closed-loop PSH proposals in the United States may mean that tribal, federal, and state agencies with authorities for cultural and natural resources protection and management involved in the FERC licensing process may not have experience with closed-loop PSH regulation. Moreover, many proposed closed-loop PSH facilities are in areas that do not have high concentrations of conventional hydropower, so these agencies may also be unfamiliar with the FERC hydropower licensing process. The goal of this report is to help license applicants, resource agencies, and other members of the hydropower community focus the scope of environmental review for the closed-loop PSH development, licensing, and federal authorization process enabling quicker identification of potential impacts, mitigations, and situations where mitigation may not be possible. We found that environmental impacts of closed-loop PSH are highly site-specific, and generalizations about the types of environmental impacts across closed-loop PSH projects are difficult to make. Environmental impacts of closed-loop PSH are like those for open-loop PSH with a few exceptions including water sourcing, which can lead to delays and contention due to potential complexities with water rights, impacts to aquatic resources, and greenhouse gas emission potential. Cultural resource impacts were commonly reported in National Environmental Policy Act (NEPA) documents reviewed and discussed in interviews, but in many cases such impacts cannot be mitigated.

13 HYDRO ENERGY↗
DOE OSTI2025

Impact Testing of Heat Source Exemplars

This report details the heat source impact testing performed at the Shock Thermodynamics Applied Research Facility (STAR). The purpose of these tests were to measure the impact behavior of a heated Ta-10W tantalum/tungsten alloy heat source exemplar. Each exemplar resembled a cylinder with a rectangular through-hole orthogonal to the cylinder axis-of-symmetry. In each test, the exemplar was impacted by a hardened steel impactor accelerated using the STAR air gun. The exemplars were impacted perpendicular to the through-hole and at an an angle to the cylindrical axis-of-symmetry. The exemplar bar stock source, impact angle, and impact velocity were varied throughout the testing series. High-speed video was used to measure dynamic impact behavior while photon doppler velocimetry (PDV) and shorting pins were used to measure the impact velocity. Foam support structures were used to thermally isolate the exemplar and provide a support structure which was non-perturbative to the impact event. Soft-catch techniques were used to minimize secondary impacts and enable recovery for detailed post-shot analysis. Results indicate positive correlation between exemplar fracture and the variables of impact velocity and impact angle. Exemplar fracture occurred consistently along a single corner of the through-hole.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mapping and Characterizing the Visual Impacts of the Existing US Wind Turbine Fleet

Visual impacts of wind turbines have been a persistent concern for wind energy development in the United States (US) for decades and remain a major source of project delays and cancellations. Assessments of visual impacts are frequently performed at a local scale for individual projects, but a comprehensive understanding of broader geographic patterns in visual impacts across the US is lacking. This paper presents a visual impact assessment of the existing land-based wind turbine fleet of the contiguous United States (CONUS). The assessment combines geographic information systems and 3D simulation methods to account for key factors driving the visual magnitude of impacts from the installed turbines. The results indicate that, despite the deployment of approximately 70,000 turbines and over 144 gigawatts of land-based wind in the CONUS, the visual impacts are very small when measured as a proportion of land area, population, and sensitive visual resources. Nonetheless, visual impacts are not evenly distributed: people experience a concentrated share in a small number of natural settings, primarily including plains, prairies, and deserts. Finally, we find that although increased density of wind development consistently leads to visual impacts across a greater proportion of land, it does not always lead to impacts to a greater share of the population. These findings suggest that visual impacts from wind energy are generally well-mitigated across the CONUS to date but also highlight the need for a deeper understanding of landscape sensitivity and individual perceptions of wind turbines in the most heavily impacted natural settings.

3D simulation↗
DOE OSTI2020

A thermodynamic analysis of hypervelocity impacts on metals

Hypervelocity impacts on solid surfaces generate and propagate shock waves and create extreme density, pressure, and temperature conditions. Understanding hypervelocity impacts requires a multi-physics approach at the intersection of fluid dynamics, solid mechanics, and quantum theory, which has the capability of spanning multiple different dominating physics regimes. These strong shock conditions found in hypervelocity impacts are studied in the context of high-speed collisions between spacecraft and meteoroids and debris. We study the problem of hypervelocity impacts on metals with the lens of understanding the processes that lead to the creation of an impact generated plasma. In order to characterize the impacting particle as well as its threat to spacecraft from the subsequent radiating plasma an analysis was performed that highlights how the kinetic energy of the impactor is deposited into a target, how the shock wave and shocked material in the target evolve, and how these effects can lead towards the creation of an impact plasma through heating. The analysis suggests that at low velocities the majority of the energy from a hypervelocity impact is stored in reversible elastic energy and does not contribute to strong heating. At higher impact velocities, nucleus and electron thermal components dominate, increasing the energy available for ionization. Overall, this work provides the complete set of state variable initial conditions for any study of hypervelocity impact plasma expansion and its effects.

42 ENGINEERING↗
DOE OSTI2024

Numerical modelling of impact seismic sources using the stress glut theory

SUMMARY Meteorite impacts have proved to be a significant source of seismic signal on the Moon, and have now been recorded on Mars by InSight seismometers. Understanding how impacts produce seismic signal is key to the interpretation of this unique data, and to improve their identification in continuous seismic records. Here, we use the seismic Representation Theorem, and particularly the stress glut theory, to model the seismic motion resulting from impact cratering. The source is described by equivalent forces, some resulting from the impactor momentum transfer, and others from the stress glut, which represents the mechanical effect of plasticity and non linear processes in the source region. We condense these equivalent forces into a point-source with a time-varying single force and nine-component moment tensor. This analytical representation bridges the gap between the complex dynamics of crater formation, and the linear point-source representation classically used in seismology. Using the multiphysics modelling software HOSS, we develop a method to compute the stress glut of an impact, and the associated point-source from hypervelocity impact simulations. For a vertical and an oblique impact at 1000 m s−1, we show that the moment tensor presents a significant deviatoric component. Hence, the source is not an ideal isotropic explosion contrary to previous assumptions, and draws closer to a double couple for the oblique impact. The contribution of the point force to the seismic signal appears negligible. We verify this model by comparing two signals: (1) HOSS is coupled to SPECFEM3D to propagate the near-source signal elastically to remote seismic stations; (2) the point-source model derived from the stress-glut theory is used to generate displacements at the same distance. The comparison shows that the point-source model is accurately simulating the low-frequency impact seismic waveform, and its seismic moment is in trend with Lunar and Martian impact data. High-frequencies discrepancies exist, which are partly related to finite-source effects, but might be further explained by the difference in mathematical framework between classical seismology and HOSS’ numerical modelling.

79 ASTRONOMY AND ASTROPHYSICS↗