Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Total Cost of Ownership Reduction Using Passive Pre-Chamber Ignition in Natural Gas Engines

Spark plug durability is a factor affecting the total cost of ownership (TCO) of spark-ignited natural gas engines, with some heavy-duty platforms requiring plug replacement after only 750 hours of operation. The high ignition energy demand under lean or diluted conditions accelerates electrode wear, shortening plug life and increasing maintenance frequency. This work evaluates passive pre-chamber (PC) ignition operating at lowered spark energies as a strategy to reduce spark energy requirements and extend plug durability, thereby lowering TCO. Experiments were conducted on a medium-duty Cummins 6.7L ISB engine at 1600 RPM and 50% load under varying exhaust gas recirculation (EGR) dilution levels (0–40%). Two passive pre-chambers with 1.1 mm and 1.6 mm nozzle diameters were compared with conventional spark ignition (SI). SI was operated with a fixed coil dwell of 4 ms (~90 mJ), while the PC configuration was tested across 2–4 ms dwell times (~30–90 mJ). Cylinder pressure analysis revealed that PC ignition sustained stable combustion at significantly lower spark energies than SI, with improved combustion stability at ~30 mJ compared with SI at ~90 mJ. The PC system also extended the dilution tolerance beyond that achievable with SI, while delivering up to ~2% higher indicated thermal efficiency and reducing the COV by nearly 90% at 30% EGR. A TCO analysis was conducted to assess the economic benefit of adopting a passive PC system operating at reduced spark energies compared to SI. It was found that adopting a passive PC system could reduce TCO by approximately $11,000 per engine over a five-year operational period, primarily due to fuel savings, extended spark plug life, and reduced maintenance frequency. These projections were weighed against the additional hardware cost of the pre-chamber, yielding a rapid estimated return on investment of ~300 operating hours. Therefore, this work motivates continued research and development of passive PC technology and its commercial adoption in natural gas engines used in transportation applications.

Dhotre, Akash [University of Minnesota]↗
DOE OSTI2021

Modeling of thermal and kinetic processes in non-equilibrium plasma ignition applied to a lean combustion engine

In recent years novel ignition systems have been developed to enable stable and efficient engine operations with lean mixtures. Among them, radio-frequency corona ignition systems create discharges that involve a much wider region compared to traditional spark, and produce non equilibrium plasma with high levels of active radicals and excited species. These devices considerably increase the early flame growth speed and extend stable operating limits. With the aim of expanding the knowledge on high efficiency lean-burn SI engines, this paper investigates and compares the combustion development generated by spark and corona ignitions through computational fluid dynamics, within the Reynolds-Averaged Navier-Stokes framework for turbulence modeling. In order to simultaneously take thermal and chemical effects into account, the Perfectly Stirred Reactor combustion model is used. Experimental data are also collected for validation in an optical access engine, for different mixture levels, from stoichiometric to very lean. Furthermore, the faster burn rate generated by the corona system in the initial stage of the combustion is well predicted by the simulations, in all the relative air-fuel ratio conditions. Remarkably, as the mixture becomes lean, simulations are able to capture the non-linear transition from fast to slow kernel growth, before a self-sustainable flame propagation is established. This correlates very well with the measured engine cyclic variability and the corresponding steep change in the duration of the flame kernel formation. Ultimately, this study highlights the important role of the atomic oxygen, as active radical, in promoting and enhancing the combustion initiated by a corona discharge, in addition to the volumetric ignition effect. By contrast, the validated simulations allow to explain that the high-temperature thermal plasma generated in a traditional spark discharge is insensitive to kinetic aspects.

42 ENGINEERING↗
DOE OSTI2022

Enhancing $\phi$-sensitivity of ignition delay times through dilution of fuel-air mixture

The high $\phi$-sensitivity (η) of ignition delay time (τ IDT ) is one of the desirable fuel properties for the high-load extension of advanced compression ignition engine. Recent studies revealed the effectiveness of a high dilution rate (x D ) for enhancing η at the engine-relevant conditions. This study aims to quantify the effect of dilution on the η of isooctane using a combined experiment-simulation approach. The ignition delay of the isooctane/air mixture was measured with an Advanced Fuel Ignition Delay Analyzer (AFIDA) over the temperature range of 623 - 923 K at 10 bar pressure with global $\phi$ = 0.3 - 0.6, with and without 28.6% of additional N 2 dilution. For precise evaluation of experimental η, the facility effect of the AFIDA experiment was characterized with three-dimensional computational fluid dynamics (3-D CFD) simulation. The temperature in the combustion chamber from 3-D CFD indicated a substantial temporal dependency, varying up to ~52 K by charge-cooling of fuel injection and heat transfer from the wall. We introduced the dimensionless number θ(t) for characterizing the temporal profile of chamber temperature. Consideration of the facility effect using θ(t) resulted in better agreement between the experimental ..eta.. and zero-dimensional (0-D) kinetics simulation. The refined η were then further utilized to quantify the effectiveness of dilution to η The extent of η enhancement with dilution strategy was maximized at the low-temperature chemistry regime, increasing η by 77% with a 28.6% dilution rate. Further analysis on the dilution effect was carried out using 0-D kinetics simulation, revealing the critical dimensionless numbers relevant to the effectiveness of dilution to η enhancement. Here, this study is the first experiment-simulation combined research to quantify the effect of dilution on η, facilitating the kinetics model refinement for better reproduction of $\phi$-sensitivity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Large-eddy simulation study on cycle-to-cycle variation of knocking combustion in a spark-ignition engine

The cycle-to-cycle variation in the knock intensity is commonly encountered under abnormal combustion conditions. The severity of these abnormal combustion events can vary significantly, and the efficiency of engines at high loads is limited in practice by heavy knocking phenomena. Since, a thorough analysis of such recurrent but non-cyclic phenomena via experiments alone becomes highly cumbersome, in the present work, a multi-cycle large-eddy simulation study was performed to quantitatively predict cyclic variability in the combustion process and cyclic knock intensity variability in a direct injection spark-ignition engine. To account for the turbulence-chemistry interaction effects on flame propagation, the G-equation combustion model was used. Detailed chemistry was solved outside the flame front with a toluene primary reference fuel skeletal kinetic mechanism. For both the mild knock and heavy knock conditions, the numerical results were validated against experimental measurements. Based on the simulation results, a correlation analysis was performed considering combustion phasing, peak cylinder pressure and maximum amplitude of pressure oscillation. Furthermore, a detailed three-dimensional spatial analysis illustrated the evolution of auto-ignition kernel development and propagation of pressure waves during knocking combustion for three typical cycles with different knock intensities. In this process, it was found that an early occurrence of auto-ignition in the end gas was prone to high knock intensity. Although multiple auto-ignition kernels were observed in different cycles, the degree of coupling between chemical heat release and pressure waves varied, thereby leading to different maximum amplitude of pressure oscillation values.

42 ENGINEERING↗
DOE OSTI2020

Ignition delay time and speciation of dibutyl ether at high pressures

Dibutyl ether (DBE) is a promising biofuel due to its high cetane number (~ 100) and high volumetric energy density (31.6 MJ/L). It could either be used directly in compression ignition engines or blended with other conventional or renewable fuels. Oxidation and pyrolysis kinetics of DBE are not well known, particularly at high pressures. In this work, we have experimentally investigated the chemical kinetics of DBE in three domains: (a) ignition delay time measurements in a rapid compression machine over T = 550–650 K, P = 10, 20, 40 bar, φ = 0.5, 1; (b) ignition delay time measurements in a shock tube over T = 900–1300 K, P = 20, 40 bar, φ = 0.5, 1; (c) laser-based carbon monoxide speciation measurements in a shock tube during DBE pyrolysis and oxidation over T = 1100–1400 K, P = 20 bar. Pressure time-histories measured in RCM experiments exhibited unique 3-stage and 4-stage ignition behavior predominantly at fuel-lean conditions. Experimental data were compared with the predictions of two recent chemical kinetic models of DBE. Sensitivity analyses were carried out to identify key reactions which may have caused the discrepancy between experiments and simulations. We found that the rate of decomposition of DBE may need to be revisited to improve the oxidative and pyrolytic predictions of DBE kinetic model.

09 BIOMASS FUELS↗
DOE OSTI2021

Model predictive combustion control of a Gasoline Compression Ignition engine

Gasoline Compression Ignition is a novel combustion concept that derives its superiority from the high compression ratio of a compression ignition engine as well as the properties of gasoline fuel, such as longer ignition delay and higher volatility compared to diesel. Here, this combustion concept was experimentally tested on a 12.4L Class 8 truck engine. Based on these experimental data, prior efforts by the authors focused on the development of an engine model for a heavy-duty engine operating on a low-reactivity fuel. This engine model was leveraged within this study to investigate a combustion control strategy at different engine conditions and injection methods and was augmented to incorporate cycle-to-cycle combustion variations. State estimation is performed by means of a Kalman filter which feeds into a model predictive controller. The model predictive controller chooses control actions based on a predefined cost function under consideration of bounds reflecting physical constraints. The engine model was utilized to establish a state-space model that serves the Kalman filter and model predictive controller for estimation and prediction. A comparative study investigating control actions and engine behavior was performed with and without limiting in-cylinder peak pressure as well as combustion noise, which is of particular interest for early pilot injection strategies. In addition, the proposed control architecture was investigated at two different levels of cycle-to-cycle variations and compared to the performance of a control structure with input disturbance rejection. For increased cycle-to-cycle variations, disturbance estimation reduces state fluctuations and control effort. In general, this investigation highlights control aspects specific to a compression-ignited combustion regime with low-reactivity fuel. The control algorithm is able to maintain the desired references for brake mean effective pressure and combustion phasing while controlling peak in-cylinder pressure and combustion noise.

42 ENGINEERING↗
DOE OSTI2024

On the modes of nanosecond pulsed plasmas for combustion ignition of quiescent CH 4 -air mixtures

The effect of transient plasma modes on ignition kernel development are discussed here for a quiescent CH 4 -air combustion model system. A 10 ns high-voltage pulse was applied to a pin-to-pin electrode in lean fuel-air mixtures at room temperature and atmospheric pressure. High-impedance streamer, transient spark and low-impedance spark discharges were identified based on pulse waveforms of voltage and current. A sustained ignition kernel expansion was observed when the plasma discharge transitioned into a transient spark or spark discharge. The minimum ignition energy was obtained at the transient spark mode, which has less than a third of the energy or Coulomb transfer compared to the low-impedance spark. Employing repetitive 10-pulse sequence at 10 kHz, the lean-fuel limit was extended from an equivalence ratio of 0.6 for the single pulse ignition to 0.5. The use of repetitive pulses also allowed streamer breakdown or spark initiation to occur at a lower voltage.

CH 4↗
DOE OSTI2023

Improved ion heating in fast ignition by pulse shaping

The fast ignition paradigm for inertial fusion offers increased gain and tolerance of asymmetry by compressing fuel at low entropy and then quickly igniting a small region. Because this hotspot rapidly disassembles, the ions must be heated to ignition temperature as quickly as possible, but most ignitor designs directly heat electrons. A constant-power ignitor pulse, which is generally assumed, is suboptimal for coupling energy from electrons to ions. Using a simple model of a hotspot in isochoric plasma, a novel pulse shape to maximize ion heating is presented in analytical form. Bounds are derived on the maximum ion temperature attainable by electron heating only. Moreover, arranging for faster ion heating allows a smaller hotspot, improving fusion gain. As a result, under representative conditions, the optimized pulse can reduce ignition energy by over 20%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Computationally efficient evaluation of optimum homogeneous charge compression ignition operating range with accelerated multizone engine cycle simulation

The very intensive calculations necessary to define a performance map requiring evaluation of over a hundred individual operating points can be efficiently conducted with accelerated multizone for engine cycle simulation, leading to a definition of regions of acceptable and optimum homogeneous charge compression ignition operation. Accelerated multizone for engine cycle simulation has the virtue of enabling accurate evaluation of many operating conditions based on thermal stratification data from a single fluid mechanics run at motored conditions. This is possible because thermal stratification is more sensitive to engine geometry than to operating conditions. In this article, accuracy of accelerated multizone for engine cycle simulation is demonstrated by comparison with experimental data for iso-octane homogeneous charge compression ignition operation over a broad range of lean equivalence ratios (0.14–0.28). The validated accelerated multizone for engine cycle simulation model is then applied to generating a performance map for an engine controlled by appropriately adjusting equivalence ratio and internal exhaust gas recirculation. Regions of acceptable and optimum combustion are identified. It is finally demonstrated that while indicated mean effective pressure remains low for optimum homogeneous charge compression ignition operation (1–4 bar), this is sufficient for a large fraction of typical driving in light-duty vehicles. Much driving including idle can therefore be done in homogeneous charge compression ignition mode at high efficiency and low (essentially zero) NOx and particulate matter emissions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

National Ignition Campaign Data Analysis by an ICF Outsider

A simple DT burn model, with no alpha-particle warming feedback, using a combination of ICF inputs and the measured ion temperature, T, volume compression, C, ablator velocity, v, and burn width time, Δt, can reproduce the national-ignition campaign (NIC) fusion yields with a rms percent difference of ~40%. Analysis suggestion the fusion-yield reproducibility of NIC events with nominally identically measured T, C, v, and Δt is <30%. The highest fusion yields, at a fixed laser energy are obtained with depleted-uranium (DU) hohlraums and high-density carbon (HDC) ablators. Small diameter fit tubes (≤5 μm) enhance fusion yields by an average of 26±15% relative to 10-μm diameter fit tubes. A dependence of fusion yield on the diameter of the capsule relative to the diameter of the hohlraum is inferred for fixed T, C, v, and Δt. No evidence of conditions close to ignition, or alpha-particle warming is found in the existing NIC data with LEH< 2MJ. To obtain a predictive model for extrapolation proposes we map the T, C, and v into power laws as a function of LEH. The above mentioned extrapolatable model has a rms percent difference from the yields of the second half of the NIC of (56 ± 4)%. Higher (and significantly lower) DT temperatures are obtained with HDC ablators (and low-foot drives). The highest compressions are obtained via low-foot drives, but this does not compensate for the corresponding lower temperatures. An extrapolation of the presented model suggests significant alpha-particle heating at an LEH of ~5 MJ. It is hoped that others more familiar it the conditions needed for ignition will use to presented model to estimate the LEH required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Poly(oxymethylene) Ethers as a High Cetane, Low Sooting Biofuel Blendstock for Use in Medium to Heavy Duty Mixing Controlled Compression Ignition Engines

Compression ignition (CI) engines are currently the most common prime mover for medium and heavy duty vehicles; these engines contribute roughly a quarter of US greenhouse gas emissions from transportation, and even higher percentages of particulate and nitrogen oxide emissions. As a result, there have been significant efforts made to reduce these emissions, particularly through selection of low-emissions alternative fuels. Oxymethylene ethers (OMEs) are a class of molecule, typically structured R-O-(CH2O)n-R', which have been considered as a possible blendstock in CI fuels for the goal of soot reduction. Generally, past work has focused on methyl-terminated OMEs, CH3-O-(CH2O)n-CH3, which by virtue of containing no C--C bonds, produce negligible soot. These molecules show significant reductions in soot emission from engines when blended in moderate to high ratios with traditional diesels, however, they have been shown to have inferior physical properties and poor compatibility with some legacy systems. Recent theoretical work has shown that OMEs with non-methyl alkyl groups may have superior performance, albeit at the cost of increased soot formation. In this work, a variety of OMEs with terminating alkyl groups from methyl to butyl are considered for their suitability as CI fuels. The synthesis of these extended OMEs is studied, including formation of n=1 OMEs from common chemical sources, and extension of the chain length to heavier molecules, via reactions over acidic ion exchange resins. Following the synthesis, the properties of these OMEs are studied with respect to their engine applicability. It is found that heavier (propyl- and butyl-terminated) OMEs have superior properties for diesel compatibility, particularly in reactivity, volatility, and water solubility. Extended-alkyl OMEs are found to have higher soot production than methyl-terminated OMEs, but remain superior to diesel soot production on a per-unit-energy basis. A sample of a butyl-terminated OME mixture, n=2-4, is selected as the ideal OME blend for close compatibility with legacy diesel systems. This mixture is blended with certified diesel and tested for ASTM D975 compatibility, passing all required tests but lubricity; decreased heat of combustion is observed but not governed by the diesel standard. Fundamental combustion tests of various mid-weight OMEs are performed in a rapid compression machine, where it is shown that low-temperature chemistry causes a region of decreased dependence of ignition delay on temperature, consistent with methyl-terminated OME behavior. An isopropyl-terminated OME is observed to have low reactivity compared to other OMEs; this fuel is investigated via further rapid compression machine testing and CFR engine testing. It is found that this OME has strong negative-temperature-coefficient ignition behavior - a first for OMEs - and has reactivity lower than other OMEs, but insufficient for direct spark ignition engine testing.

09 BIOMASS FUELS↗
DOE OSTI2022

Technology Enablers for Advanced Gasoline Compression Ignition Engines

To meet current emission regulations and increasingly demanding global fleet CO2 standards on fuel economy and future trends towards life cycle GHG emissions, advanced combustion engines remain significant in the passenger vehicle sector to achieve high efficiency and low emissions over the full operating range. Lean burn gasoline compression ignition (GCI) technology has shown to have the most potential in reaching these goals, although it faces challenges in the operating range. In this study, an advanced GCI engine is considered with the capability to operate under two combustion modes, namely low temperature combustion (LTC) and GCI. They are enabled with the use of two Hyundai in-house developed technologies; an advanced valve control mechanism known as continuously variable valve duration (CVVD) and a high-pressure gasoline injection system. At low load, the engine utilizes dual CVVD and dual CVVT (continuously variable valve timing) mechanisms for both intake and exhaust valvetrains to enable NVO (negative valve overlap) to trap hot residuals. The hot residuals enable low load auto-ignition, and the phasing control of that auto-ignition is achieved by varying the degrees of NVO, and in turn, the amount of hot residuals. This is done in real time with respect to the changes in engine loads or operating conditions, significantly improving cylinder-phasing control in LTC mode, and subsequently is able to realize a fuel economy gain and reduced emission benefits. Early direct injection during NVO or intake stroke is used to form homogenous or quasi-homogenous air-fuel mixture for LTC. At mid to high loads, late direct injection of gasoline or GCI mode is employed to take advantage of the high volatility and high resistance to auto-ignition of gasoline fuel, so that diesel-engine like high combustion efficiency can be achieved with lower soot emissions for the same NOx level as diesel combustion. In this paper, the key control and fueling technologies that enable this multiple mode combustion are introduced, and the resultant analysis on engine test and CFD simulation at LTC and GCI operating conditions are presented in detail.

Gasoline compression ignition, low temperature com↗
DOE OSTI2025

Thermal Gradient Effects on Local Hotspot Ignition in 1,3,5,7‐Tetranitro‐1,3,5,7‐tetrazocane (HMX)

Understanding hotspot ignition, growth, and criticality, as well as the timescales of each, is crucial for parameterizing mesoscale and continuum‐level models that rely on a statistical understanding of hotspots. However, these models often consider hotspots to have uniform temperatures or for hotspots of a given temperature and size to always behave the same. Therefore, using molecular dynamics simulations, we assess the influence of thermal distribution effects on hotspot local ignition and time to ignition in 1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocane (HMX) nanoscale hotspots. Finally, by assessing hotspots with a gradient driven from an initial two‐temperature core–shell setup, we show that small increases in the core temperature under a constant average temperature can lead to order‐of‐magnitude effects on reaction and local ignition timescales.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Piston geometry and stroke optimization for high efficiency propane spark ignition engines

Propane has unique properties and offers interesting characteristics for high-efficiency spark ignition engines. Its high volatility reduces or completely eliminates fuel-wall wetting and facilitates fuel air mixing. Furthermore, propane has a research octane number of 112 and a high octane sensitivity of 15. Finally, its laminar flame speed is on the same order as that of conventional gasoline, and it exhibits high dilution tolerance. Modern spark ignition internal combustion engines rely on fast combustion rates and high dilution to achieve high brake thermal efficiencies. To accomplish this, high stroke-to-bore ratios and high geometric compression ratios have been used in new engine designs. Therefore, propane’s relatively high laminar flame speeds, high knock resistance, and dilution tolerance make it an excellent candidate fuel for modern spark ignition engines. The objective of this work is to co-optimize the piston geometry and the engine stroke to maximize the efficiency of a spark-ignition engine fueled with propane. 3D computational fluid dynamics (CFD) simulations employing the extended coherent flamelet model were used to study the parametric effects of piston shape and stroke length. A piston geometry based on high performing pistons was parameterized using four controlling parameters. The piston geometry and engine stroke design space was explored using deterministic and quasi-random sampling techniques. In conclusion, a Gaussian process regression model was built using the simulation data to explain the results observed.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Data-driven chemical kinetic reaction mechanism for F-24 jet fuel ignition

A data-driven chemical kinetic mechanism for the military version of Jet A, F-24, is developed for numerical simulations of the ignition process. The main purpose of this study is to obtain a practical F-24 mechanism across wide temperature and equivalence ratio ranges, with a particular focus on the negative temperature coefficient and low temperature regions. The new mechanism (ARLMech-HC-F24) is based on the HyChem model of a similar fuel and optimized using a micro-genetic algorithm against an experimental ignition delay data set of the target fuel. The development and optimization processes include reaction selection, population creation, shuffled tournament implementation based on a merit function, and child-individual creation for the next generation. Several techniques and parameters are proposed to generate an accurate mechanism through an efficient process. The newly introduced data-driven mechanism based on these techniques shows better merit value convergence and represents the ignition behavior more accurately than that without the techniques. This practical mechanism is suitable for the numerical simulations of the F-24 or Jet A ignition problem, and the suggested strategies can be employed in similar problems of rate coefficients estimation.

42 ENGINEERING↗
DOE OSTI2020

Hotspot conditions achieved in inertial confinement fusion experiments on the National Ignition Facility

We describe the overall performance of the major indirect-drive inertial confinement fusion campaigns executed at the National Ignition Facility. With respect to the proximity to ignition, we can describe the performance of current experiments both in terms of no-burn ignition metrics (metrics based on the hydrodynamic performance of targets in the absence of alpha-particle heating) and in terms of the thermodynamic properties of the hotspot and dense fuel at stagnation—in particular, the hotspot pressure, temperature, and areal density. We describe a simple 1D isobaric model to derive these quantities from experimental observables and examine where current experiments lie with respect to the conditions required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Directly driven magnetized fast-ignition targets with steep density gradients for inertial fusion energy

The development of advanced targets capable of achieving ignition with improved energy gain at lower driver energies is one of four key technical challenges to be solved in order to realize economical inertial fusion energy. We report the minimum energy necessary for a small hemispherical mass of fast-ignited high-density deuterium–tritium fuel to explosively ignite a significantly larger hemispherical mass of assembled cold fuel with much lower mass density, both with and without a flux-compressed magnetic field connecting the two regions. With the magnetic field, the burn rate improves, and lower energy states become more effective. The imploded fuel reservoir available in the lower-density, larger-mass region of the steep density gradient determines whether the fusion yield is several hundred MJ or up to a few GJ. We report a case wherein the cold reservoir ignited and produced high gain with the assistance of only ~700 kJ of hotspot yield, an amount that has already been demonstrated as feasible in laboratory experiments using indirect-drive targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Simulated signatures of ignition

Ignition on the National Ignition Facility (NIF) provides a novel opportunity to evaluate past data to identify signatures of capsule failure mechanisms. We have used new simulations of high-yield implosions as well as some from past studies in order to identify unique signatures of different ignition failure mechanisms: jetting due to the presence of voids or defects, jetting due to the capsule fill tube, interfacial mixing due to instabilities or due to plasma transport, radiative cooling due to the presence of contaminant in the hot spot, long-wavelength drive asymmetry, and preheat. Many of these failure mechanisms exhibit unique trajectories that can be distinguished through variations in experimental observables such as neutron yield, down-scattered ratio (DSR), and burn width. Our simulations include capsules using both plastic and high-density carbon ablators and span all high-yield designs considered since the beginning of the National Ignition Campaign in 2011. We observe that the variability in trajectories through the space of neutron yield, DSR, and burn width varies little across capsule design yet are unique to the failure mechanism. The experimental trajectories are most consistent with simulated preheat and jetting due to voids and defects, which are the only failure mechanisms that are indistinguishable in our analysis. This suggests that improvements to capsule compression due to improved capsule quality or reduced preheat have played a primary role in enabling high yields on NIF. Furthermore, our analysis suggests that further improvements have the potential to increase yields further.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗