Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “idaho”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

UNREVIEWED DISPOSAL QUESTION EVALUATION: Disposal of the Idaho National Laboratory Classified Mockup Low-Level Waste, Revision 1, at the Area 5 Radioactive Waste Management Site, Nevada National Security Site, Nye County, Nevada

This Unreviewed Disposal Question Evaluation (UDQE) assesses whether the Idaho National Laboratory (INL) Classified Mockup Low-Level Waste (LLW) (INEL208599QR0, Revision 1 [INL 2021]) is suitable for shallow land burial (SLB) at the Area 5 Radioactive Waste Management Site (RWMS) on the Nevada National Security Site (NNSS). Disposal of the INL Classified Mockup LLW meets all performance objectives of U.S. Department of Energy (DOE) Manual DOE M 435.1-1, Radioactive Waste Management Manual, Chapter IV, Section P (DOE 1999). The INL Classified Mockup LLW stream is recommended for acceptance without conditions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Idaho's Clean Energy Jobs Potential Through 2030

According to the U.S. Census Bureau, Idaho had 1,127,985 people in its working population (15 to 64 years of age) in 2019. The graphs below show solar photovoltaic (PV), land-based wind, battery energy storage (BES), and energy efficiency job estimates in 2020, 2025, and 2030. These job estimates do not represent net job creation. Rather, they represent the size of the workforce required to achieve projected national deployment levels of each technology for 2025 and 2030 if the state captures the same proportion of jobs in the sector as it did in 2020.

clean energy↗
DOE OSTI2022

Progress on Pu-238 Production at Idaho National Laboratory From March 2021 to February 2022

Idaho National Laboratory has completed irradiation of Np-237 targets in the Advanced Test Reactor’s (ATR) South Flux Trap (SFT) and I-7 positions. INL also progressed qualification of new ATR Gen 1 Np-237 targets for the North East Flux Trap (NEFT), inner A, and H positions. This paper gives an overview of operational and technical activities from March 2021 to February 2022.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2022

Multi-Modal Characterization of Nuclear Fuels and Materials at the Idaho National Laboratory Materials & Fuels Complex

The Idaho National Laboratory (INL) leads cutting-edge research pertaining to the advancement of nuclear reactor technologies, including nuclear fuels and materials. The INL Irradiated Materials Characterization Laboratory (IMCL), Electron Microscopy Laboratory (EML), and future Sample Preparation Laboratory (SPL) are available to the nuclear research community to assess the behavior of nuclear fuels and materials, efficiently and comprehensively characterizing from the engineering to atomistic scale. The IMCL is a unique, 12,000-square-foot facility located at the INL Materials and Fuels Complex designed for analysis of irradiated materials. The facility operates advanced characterization instruments that are sensitive to vibration, temperature, and electromagnetic interference in modular radiological shielding and confinement systems, granting researchers the ability to assess the microstructural, chemical, mechanical and thermophysical properties of nuclear materials, especially irradiated fuels. The EML is dedicated to advanced characterization of materials with optical and electron microscopy tools, including scanning electron microscopy/focused-ion beam (SEM/FIB) and transmission electron microscopy (TEM). Upon construction, the SPL will be a 3 story, 49,000 sq. ft facility, that is the most modern reactor structural materials testing and analysis facility in the world, designed to investigate reactor structural materials in support of life-extension programs and development of advanced reactor concepts, including mechanical testing and advanced characterization capabilities. This presentation will showcase some of the main capabilities available at both IMCL, EML, and SPL, specifically illustrating how these characterization techniques are incorporated into multi-modal characterization work scopes to elucidate the degradation of nuclear structural materials and irradiated fuels.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Pillars of Innovation Across Southeast Idaho & the Interstate-15 Corridor

Since 1949, Idaho National Laboratory (INL) has been home to developing civilian and defense nuclear reactor technologies and managing spent nuclear fuel. Today, INL is the nation’s nuclear energy research laboratory, sustaining the safe and efficient operation of existing reactors, powering science in space, and breaking ground on the future fleet of advanced nuclear reactors. INL is only one of many rising technology resources in the region, however. Along the Interstate 15 (I-15) corridor, technology and cybersecurity industries and intellectual assets are rapidly expanding. Creating an innovation hub in this region would unite capabilities to solve current and future challenges in nuclear reactor sustainment and expanded deployment, integrated fuel cycle solutions, integrated energy systems, advanced materials and manufacturing for extreme environments, and secure and resilient cyber-physical systems.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Idaho National Laboratory Energy Cybersecurity Programs Update

This brief presentation provides a status update on three Idaho National Laboratory energy cybersecurity programs of particular interest to NERC Reliability and Security Technical Committee annual in-person Security Groups summit. Public information on the following three programs is included: Cybersecurity for Operational Technology Environments (CyOTE™) program Cyber-Informed Engineering (CIE) Cyber Testing for Resilient Industrial Control Systems (CyTRICS) program, and associated high-level information on the Energy Software Bill of Materials POC, Executive Order 14017, and the Energy Cyber Sense Act

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Progress on Pu-238 Production at Idaho National Laboratory From February 2022 to December 2022

Idaho National Laboratory (INL) has continued to qualify irradiation positions in the Advanced Test Reactor (ATR) for Pu-238 production to support NASA deep space missions. Over the past year, INL qualified Np-237 targets for ATR’s North East Flux Trap (NEFT), inner A, and H positions. Work has begun to requalify the South Flux Trap (SFT) and qualify the East Flux Trap (EFT) for the ATR GEN I target and is midway through the qualification process. This paper gives an overview of operational and technical activities from February 2022 to December 2022.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

Verification and Validation Activities of Molten Salt Reactors Multiphysics Coupling Schemes at Idaho National Laboratory

This paper presents the latest verification and validation activities in molten salt reactor modeling and simulation performed at Idaho National Laboratory. Multiphysics solutions are obtained by coupling the neutronics code Griffin, the thermal hydraulics code Pronghorn, and the system analysis code SAM, under the MOOSE framework. We present various multiphysics coupling schemes with these codes for molten salt reactor problems and provide verification and validation results. First, we present verification test results of the Griffin-Pronghorn coupled scheme for the CNRS benchmark. Then validation test results are presented for the Griffin-SAM coupled scheme for the pump startup and coast down transients of the Molten Salt Reactor Experiment. Finally, the Griffin-Pronghorn-SAM coupled scheme is demonstrated for the Molten Salt Reactor Experiment reactivity insertion transient using a domain-overlapping coupling algorithm between Pronghorn and SAM. The results of these various coupling schemes demonstrate the ability to capture the effect of fuel flow and the various feedback mechanisms important to MSRs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Pu-238 Production Progress at Idaho National Laboratory From December 2022 to December 2023

Idaho National Laboratory (INL) has an ongoing effort to produce Pu-238 for NASA deep space missions. Recent work at INL has consisted of irradiation of Pu 238 production targets in the Advanced Test Reactor (ATR), generating more than an estimated 400 grams of Pu-238 heat source material between March and October 2023. Additionally, INL began qualifying Pu-238 production targets with a higher loading of Np-237 to further increase the production of Pu-238 production in later years. INL has also updated the analysis as a result of operational changes at ATR. One instance was updating the analysis to enable a single Pu-238 production target to be run in ATR’s South Flux Trap (SFT), rather than the previous seven production targets, to make use of a spare target from a discontinued design. Higher lobe powers in ATR were also analyzed due to potential changes in planned lobe powers.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

Process Improvement For Pu-238 Production at Idaho National Laboratory

Idaho National Laboratory (INL) has supported the production of Pu-238 for future NASA deep space missions since 2017. Over this time, INL has worked to improve the qualification process of Pu-238 production targets as well as improve processes related to the shipping, storage, irradiation, and storage of Pu-238 production targets. Qualification of Pu-238 production targets began with flux measurements and scoping analysis to provide fundamental data to confirm the impacts on the operation of the Advanced Test Reactor (ATR), Fig1. Later, initial production targets were irradiated in ATR’s I-7 position, and then the South Flux Trap (SFT). A modified target design was then implemented which would use the full length of the ATR core and increase Pu-238 production. While working to improve and streamline the qualification of the Pu-238 production targets, INL worked to improve multiple operational aspects of the Pu-238 production process. These changes include updating procedures to streamline operations, supporting modification of shipping containers to contain five rather than one production target, reviewing target receipt procedures and changing work flow to provide flexibility in target receipt, and designing and fabricating support equipment for the storage and internal transfer of production targets

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

Process Improvements For Pu-238 Production at Idaho National Laboratory

Idaho National Laboratory (INL) has supported the production of Pu-238 for future NASA deep space missions since 2017. Over this time, INL has worked to improve the qualification process of Pu-238 production targets as well as improve processes related to the shipping, storage, irradiation, and storage of Pu-238 production targets. Qualification of Pu-238 production targets began with flux measurements and scoping analysis to provide fundamental data to confirm the impacts on the operation of the Advanced Test Reactor (ATR), Fig1. Later, initial production targets were irradiated in ATR’s I-7 position, and then the South Flux Trap (SFT). A modified target design was then implemented which would use the full length of the ATR core and increase Pu-238 production. While working to improve and streamline the qualification of the Pu-238 production targets, INL worked to improve multiple operational aspects of the Pu-238 production process. These changes include updating procedures to streamline operations, supporting modification of shipping containers to contain five rather than one production target, reviewing target receipt procedures and changing work flow to provide flexibility in target receipt, and designing and fabricating support equipment for the storage and internal transfer of production targets.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

FUEL PERFORMANCE STUDIES AT IDAHO NATIONAL LABORATORY MAKING USE OF THE BYRON FUEL SHIPMENT

In December of 2023 a shipment of commercially irradiated fuel rods from the Byron Generating Station in Illinois was successfully shipped to the Materials and Fuels Complex (MFC) at Idaho National Laboratory (INL). The make-up of the rods includes a mix of cladding types from traditional ZirloTM, advanced zirconium alloys, and chrome coated ZirloTM. Burnups range from regular end of life values to over 70 GWd/MTU rod average. The R&D plan for the rods involves multiple projects from developing licensing data for new claddings to integral transient tests to support burnup extension efforts in the United States. The R&D began in early 2024 with the nondestructive examinations of the rods after which they will be sectioned for microscopy, mechanical testing, and analytical chemistry. Additionally, many rod segments will be refabricated into new test pins and inserted into a static water capsule for integral Reactivity Initiated Accident (RIA) and Loss of Coolant Accident (LOCA) testing at the TREAT reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Fusion Energy Research at Idaho National Laboratory: Experimentation and Simulation to Support Safety and Rapid Technology Development

Research into fusion energy is growing rapidly, responding to a call for sustainable sources of energy to replace fossil fuels and mitigate climate change. Within the United States, at least, researchers are also responding to the “Bold Decadal Vision” proposed by the White House, seeking to have a commercially relevant fusion pilot plant deployed within a decade. Before this can become a reality, many Fusion Science & Technology (FS&T) gaps remain. For over 45 years, Idaho National Laboratory has been at the forefront of addressing these FS&T gaps in the context of fusion safety and technology via the operation of world-leading experimental facilities within the Safety and Tritium Applied Research (STAR) Facility. Here, INL focuses on the tritium fuel cycle, conceptual system design studies, risk assessment, waste management, and materials safety. Modeling and Simulation (M&S) has also been a component of this portfolio of research, but, early on, focused on individual systems. Since 2019, active development and research on integrated whole device modeling tools based on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework has been undertaken. This has culminated in a MOOSE-based version of the Tritium Migration and Analysis Program (TMAP), an INL code historically focused on tritium permeation and trapping within fusion systems. More recently, INL Laboratory Directed Research and Development funds have been used to create the Fusion ENergy Integrated multiphys-X (FENIX) code focused on scrape-off layer plasma physics and the first wall of a magnetically confined fusion device. This talk will focus on an overview of INL activities in the FS&T research area, with a particular focus on recent M&S activities and results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

RELAP5-3D HTGR Validation Work at Idaho National Laboratory

Prismatic block-type high-temperature gas-cooled reactors (HTGRs) were built in the United States decades ago, and now advanced reactor vendors are seeking to deploy them again for a variety of applications. Deploying these reactors requires modelling and simulation tools that have been validated against conditions representative of the HTGR application. Idaho National Laboratory (INL) is leading the execution an of HTGR thermal hydraulics benchmark to accelerate the validation of thermal hydraulics modelling and simulation tools for these applications. That benchmark is based on a facility called the High Temperature Test Facility (HTTF). This work provides an overview of work conducted at INL over the last 2 years to validate RELAP5-3D against data from HTTF. This presentation shows results from multiple RELAP5-3D models and an HTTF experiment to assess the impact of certain modelling assumptions on results. The contents of this talk sit on the cutting edge of RELAP5-3D validation for HTGR analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗