Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Operando neutron imaging-guided gradient design of Li-ion solid conductor for high-mass-loading cathodes

High-mass-loading cathodes are crucial for achieving high energy density in all-solid-state batteries from the lab scale to industry. However, as mass-loading increases, electrochemical performance is significantly compromised due to sluggish kinetics. In this work, operando neutron imaging is deployed on a high-mass-loading NMC 811 cathode of 33 mg/cm 2 (5.0 mAh/cm 2 ) and directly visualizes the lithiation prioritization of the cathode active material (CAM) from the solid electrolyte membrane side to the current collector side. In addition to the tortuosity, another key limitation on ion transfer in the cathode arises from the mismatch between the uniform distribution of the solid electrolyte (catholyte) in the conventional composite cathode and the non-uniform Li + flux generated by the faradaic reaction of CAMs. Therefore, we engineer a gradient in the catholyte concentration to match the Li + flux distribution as a means of eliminating the ion transfer obstacle. This approach demonstrates enhanced rate performance, even with high-mass-loading cathodes. A LiCoO 2 composite cathode with 100 mg/cm 2 high-mass-loading exhibits an areal capacity of 10.4 mAh/cm 2 at a current density of 2.25 mA/cm 2 . This work provides insight into the ion-transport limitation in thick cathodes and demonstrates an effective gradient design to overcome the kinetic barrier and achieve high battery performance.

Batteries↗
NASA NTRS1972

Fatigue crack growth from a circular hole with and without high prior loading

Fatigue crack growth from a circular hole was investigated experimentally and analytically. An aluminum-alloy sheet specimen was cycled under a single level of loading with and without prior high loads. Tests showed that the crack propagation life was significantly longer when the high loads were applied initially. This longer life was attributed to compressive residual stresses produced near the hole by the initial high loads. The residual stresses near the hole were determined by an elastoplastic analysis and were then used to develop a stress-intensity solution for a crack growing through the residual stress field. This solution and a similar solution for the case of no prior loading were used to predict crack growth. The predicted crack growth agreed closely with the experimental values.

Crews, J. H., Jr.↗
DOE OSTI2026

High waste loading glass formulation development for high-P HLW

The primary objective of the work described herein was to develop and identify HLW glass compositions and glass forming additive blends that achieve high waste loadings and processing rates for high phosphorus HLW streams while maintaining acceptable glass properties. This was accomplished through a combination of crucible-scale tests, vertical gradient furnace tests, and confirmation tests on the DM100 melter system.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

High waste loading glass formulation development for High-Mn HLW

One of the primary objectives of the work described herein was to develop and identify HLW glass compositions and glass forming additive blends that achieve high waste loadings and processing rates for high manganese HLW streams while maintaining acceptable glass properties. Another objective was to determine the effect of the form of manganese (MnO, MnO2, MnCO3) on feed processing properties, glass production rates, and product quality while vitrifying a high manganese HLW stream. This was accomplished through a combination of crucible-scale tests, vertical gradient furnace tests, and confirmation tests on a DM100 melter system.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2004

BASS Code Development

The BASS computational aeroacoustic code solves the fully nonlinear Euler equations in the time domain in two-dimensions. The acoustic response of the stator is determined simultaneously for the first three harmonics of the convected vortical gust of the rotor. The spatial mode generation, propagation and decay characteristics are predicted by assuming the acoustic field away from the stator can be represented as a uniform flow with small harmonic perturbations superimposed. The computed field is then decomposed using a joint temporal-spatial transform to determine the wave amplitudes as a function of rotor harmonic and spatial mode order. This report details the following technical aspects of the computations and analysis. 1) the BASS computational technique; 2) the application of periodic time shifted boundary conditions; 3) the linear theory aspects unique to rotor-stator interactions; and 4) the joint spatial-temporal transform. The computational results presented herein are twofold. In each case, the acoustic response of the stator is determined simultaneously for the first three harmonics of the convected vortical gust of the rotor. The fan under consideration here like modern fans is cut-off at +, and propagating acoustic waves are only expected at 2BPF and 3BPF. In the first case, the computations showed excellent agreement with linear theory predictions. The frequency and spatial mode order of acoustic field was computed and found consistent with linear theory. Further, the propagation of the generated modes was also correctly predicted. The upstream going waves propagated from the domain without reflection from the in ow boundary. However, reflections from the out ow boundary were noticed. The amplitude of the reflected wave was approximately 5% of the incident wave. The second set of computations were used to determine the influence of steady loading on the generated noise. Toward this end, the acoustic response was determined with three steady loading conditions: design, low-loading, high-loading. The overall trend showed significant (approximately 10 dB) increases in the generated noise for the highly loaded stator.

Sawyer, Scott↗
DOE OSTI2020

Rheological behavior and fiber spinning of polyacrylonitrile (PAN)/Carbon nanotube (CNT) dispersions at high CNT loading

Rheological studies play an important role in polymer processing including fiber spinning. In the current work, rheological behavior has been studied for polyacrylonitrile (PAN)/carbon nanotube (CNT) dispersions in dimethyl formamide (DMF), where CNT loading is as high as 15 wt% of the total solids (polymer + CNT). The presence of CNTs increased the elastic-like and shear thinning behavior of the dispersions. The terminal slope of the log G' versus log G" curve, which was used to characterize the homogeneity of solution or dispersion, is dependent on the CNT concentration but independent of temperature between 0 and 60 °C. PAN/CNT-10 (90 wt% PAN +10 wt% CNT) and PAN/CNT-15 were gel spun at different conditions, with small diameter capillary at high shear rate and large diameter capillary at relatively low shear rate. Additionally, for PAN/CNT-10, fiber spinning with lower molecular weight polymer showed increased continuous jetting time when compared to spinning with higher molecular weight polymer. In addition, the rheological behavior of PAN/cellulose nanocrystal (CNC) dispersion with 20–60 wt% CNC was also compared to that of the PAN/CNT dispersions. PAN/CNC and PAN/CNT share similarities in both rheological behavior and fiber spinning at high filler loading.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2001

Axial and Torsional Load-Type Sequencing in Cumulative Fatigue: Low Amplitude Followed by High Amplitude Loading

The experiments described herein were performed to determine whether damage imposed by axial loading interacts with damage imposed by torsional loading. This paper is a follow on to a study that investigated effects of load-type sequencing on the cumulative fatigue behavior of a cobalt base superalloy, Haynes 188 at 538 C Both the current and the previous study were used to test the applicability of cumulative fatigue damage models to conditions where damage is imposed by different loading modes. In the previous study, axial and torsional two load level cumulative fatigue experiments were conducted, in varied combinations, with the low-cycle fatigue (high amplitude loading) applied first. In present study, the high-cycle fatigue (low amplitude loading) is applied initially. As in the previous study, four sequences (axial/axial, torsion/torsion, axial/torsion, and torsion/axial) of two load level cumulative fatigue experiments were performed. The amount of fatigue damage contributed by each of the imposed loads was estimated by both the Palmgren-Miner linear damage rule (LDR) and the non-linear damage curve approach (DCA). Life predictions for the various cumulative loading combinations are compared with experimental results.

Bonacuse, Peter J.↗
DOE OSTI2022

Nickel Hydroxide Nanofluid Cathodes with High Solid Loadings and Low Viscosity for Energy Storage Applications

Nanofluid electrodes with high loading of active solid materials have significant potential as high energy density flow battery electrolytes; however, two key criteria need to be met: they must have a manageable viscosity for pumping and simultaneously exhibit good electrochemical activity. A typical dispersion of nickel hydroxide nanoparticles (~100 nm) is limited to 5–10 wt.% of solids, above which it has a paste-like consistency, incompatible with flow applications. We report on the successful formulation of stable dispersions of a nano-scale nickel hydroxide cathode (β-Ni(OH) 2 ) with up to 60 wt.% of solids and low viscosity (32 cP at 25 °C), utilizing a surface graft of small organic molecules. The fraction of grafting moiety is less than 3 wt.% of the nanoparticle weight, and its presence is crucial for the colloidal stability and low viscosity of suspensions. Electrochemical testing of the pristine and modified β-Ni(OH) 2 nanoparticles in the form of solid casted electrodes were found to be comparable with the latter exhibiting a maximum discharge capacity of ~237 mAh/g over 50 consecutive charge–discharge cycles, close to the theoretical capacity of 289 mAh/g.

25 ENERGY STORAGE↗
NASA NTRS2008

Seal Technology for Hypersonic Vehicle and Propulsion: An Overview

Hypersonic vehicles and propulsion systems pose an extraordinary challenge for structures and materials. Airframes and engines require lightweight, high-temperature materials and structural configurations that can withstand the extreme environment of hypersonic flight. Some of the challenges posed include very high temperatures, heating of the whole vehicle, steady-state and transient localized heating from shock waves, high aerodynamic loads, high fluctuating pressure loads, potential for severe flutter, vibration, and acoustic loads and erosion. Correspondingly high temperature seals are required to meet these aggressive requirements. This presentation reviews relevant seal technology for both heritage (e.g. Space Shuttle, X-15, and X-38) vehicles and presents several seal case studies aimed at providing lessons learned for future hypersonic vehicle seal development. This presentation also reviews seal technology developed for the National Aerospace Plane propulsion systems and presents several seal case studies aimed at providing lessons learned for future hypersonic propulsion seal development.

Steinetz, Bruce M.↗
NASA NTRS2011

Utilizing Photogrammetry and Strain Gage Measurement to Characterize Pressurization of Inflatable Modules

This paper focuses on integrating a large hatch penetration into inflatable modules of various constructions. This paper also compares load predictions with test measurements. The strain was measured by utilizing photogrammetric methods and strain gages mounted to select clevises that interface with the structural webbings. Bench testing showed good correlation between strain data collected from an extensometer and photogrammetric measurements, even when the material transitioned from the low load to high load strain region of the curve. The full-scale torus design module showed mixed results as well in the lower load and high strain regions. After thorough analysis of photogrammetric measurements, strain gage measurements, and predicted load, the photogrammetric measurements seem to be off by a factor of two.

Mohammed, Anil↗
NASA NTRS1939

The Calculated Effect of Various Hydrodynamic and Aerodynamic Factors on the Take-Off of a Large Flying Boat

Present designs for large flying boats are characterized by high wing loading, high aspect ratio, and low parasite drag. The high wing loading results in the universal use of flaps for reducing the takeoff and landing speeds. These factors have an effect on takeoff performance and influence to a certain extent the design of the hull. An investigation was made of the influence of various factors and design parameters on the takeoff performance of a hypothetical large flying boat by means of takeoff calculations. The parameters varied in the calculations were size of hull (load coefficient), wing setting, trim, deflection of flap, wing loading, aspect ratio, and parasite drag. The takeoff times and distances were calculated to the stalling speeds and the performance above these speeds was studied separately to determine piloting technique for optimum takeoff. The advantage of quick deflection of the flap at high water speeds is shown.

Olson, R.E.↗
DOE OSTI2024

Seasonal Cost-Benefit Analysis of Automated Distribution Feeder Upgrades with Advanced Mitigation Technologies

The increasing deployment of distributed solar photovoltaics (DPV) to meet clean energy goals can trigger adverse grid operation issues, such as voltage excursions and the violation of thermal loading constraints of the power delivery elements (e.g., lines and transformers) on the evolving electricity infrastructure. Such integration issues would require distribution upgrades with associated costs to mitigate them and to maintain reliable and resilient grid operating conditions. Traditional distribution network upgrade approaches use a specific single snapshot analysis that is overly conservative. This study considers a multi-time point analysis to capture both moderate (probable bounds) and extreme grid operating conditions using time points such as minimum load with minimum photovoltaics (PV), maximum load with maximum PV, maximum load with minimum PV, and minimum load with maximum PV. Further, this study investigates seasonal variation impacts and associated distribution upgrade costs for a spring season case (March, representing a low load and high PV scenario) and a summer case (July, representing a high load and high PV scenario). Such seasonal analysis will allow system operators to characterize upgrade requirements and associated costs across various periods. Because the spatial distribution of DPV can impact upgrade and associated costs, this study investigates three common DPV deployment scenarios - randomly deployed, close to the substation, and far from the substation - at different penetration levels. Apart from spatial distribution impacts, this project evaluates the techno-economic impacts of the nodal photovoltaic penetration factor (NPPF) for generating the various DPV deployment scenarios at increasing penetration levels. This project investigates the impact of varying nodal PV-to-load ratios using conservative and extreme NPPF values of 3 and 10, respectively. This study investigates the deployment of traditional infrastructure upgrade strategies, such as installing new voltage regulating equipment, transformers and lines replacements, and the activation of advanced inverter functionality (e.g., autonomous volt/VAR) in expanding PV hosting capacity. Existing DPV systems are assumed to operate with the legacy unity power factor, and we considered the possibility of retrofitting such systems with the activation of volt/VAR control as integration standards and regulations continue to evolve to allow such functions. The cost-benefit analysis metrics used in study include distribution upgrade costs, average cost per watt of the upgrade cost, average marginal cost per watt of the upgrade cost, and power losses.

14 SOLAR ENERGY↗
DOE OSTI2024

Promoting electrochemical rates by concurrent ionic-electronic conductivity enhancement in high mass loading cathode electrode

Enhancing the fast charging capacity of thick electrodes with high mass loading is imperative in expediting the widespread adoption of electric vehicles. Nonetheless, the insufficient charge transfer kinetics of thick electrodes hinder the movement of effective electrons and ions, hence diminishing capacity at high current rates. In this work, we applied sustainable and biodegradable cellulose nanocrystals (CNCs) as electrode additives. It is the first time to simultaneously improve the electronic conductivity by optimizing the carbon dispersion and establishing electron transfer networks, as well as boosting the ionic conductivity of electrodes by shortening the ion transfer pathway. Specifically, the LiNi 0.6 Mn 0.2 Co 0.2 O 2 electrodes incorporating 1% dual functional CNCs additive exhibit improved effective electrical conductivity from 0.11 to 0.16 S/m and risen effective ionic conductivity from 0.36 to 0.62 S/m, in comparison to counterpart electrodes without CNCs. Therefore, the 1% CNC electrode with a high mass loading of 27.0 mg/cm 2 delivers a discharge capacity of 128 mAh/g at 1 C, which is superior to that of the CNC-free electrodes (95 mAh/g). In short, this study presents a novel environmentally friendly, economically viable, and dual-functional electrode additive that enhances both electronic and ionic conductivities with the aim of facilitating the widespread adoption of fast-charging high mass loading electrodes.

25 ENERGY STORAGE↗
NASA NTRS1979

A comparison of the pitching and plunging response of an oscillating airfoil

An oscillating SC1095 airfoil model was tested for its aerodynamic stability in a rigid body with a single degree of freedom pitch about its quarter chord, and also in a rigid body with single degree of freedom plunge. The ability of pitching data to model plunging motions was evaluated. A one to one correspondence was established between pairs of pitching and plunging motions according to the potential flow transformation formula alpha=ikh. The imposed variables of the experiment were mean incidence angle, amplitude of motion, free stream velocity, and oscillatory frequency. Results indicate that significant differences exist between the aerodynamic responses to the motions, particularly at high load conditions. At high load conditions, the normal force for equivalent pitch is significantly greater than that for true pitch at the geometric incidence angle.

Carta, F. O.↗
DOE OSTI2022

Wire-coil insert optimization for high-heat-load/flux synchrotron components

Many synchrotron components require high levels of internal-flow, forced-convection heat transfer to minimize surface temperatures, thermal gradients, and thermally induced stress on high-power beam-interacting surfaces. Wire-coil inserts, physically similar to a common spring, are mechanically fitted inside of component cooling passages to optimize heat transfer performance. They are routinely used in Advanced Photon Source (APS) front end and beamline high-heat-load/flux components to significantly enhance convection heat transfer-up to 400% compared to plain open passages. This has the additional benefit of greatly reducing coolant flow requirements for these components. Using several cooling passage sizes, five different wire sizes, and a range of pitch values, an experimental investigation conducted at the APS has determined the average heat transfer coefficient and resulting pressure loss as a function of water flow rate for 65 different wire-coil inserts. Data from this study have been non-dimensionalized and generalized to yield relationships that can be used to determine the heat transfer performance and resulting pressure loss for any given wire-coil insert that may be used at the APS. Through data reduction, the wire-coil insert characteristic dimensions have also been optimized to yield the highest heat transfer enhancement while minimizing the coolant flow requirements. These generalized expressions for wirecoil inserts will be presented, and they can be used by scientists and engineers during the component design process to evaluate achievable heat transfer performance and associated pressure loss, aiding in the establishment of optimized operating parameters and cooling passage flow distribution schemes.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Immobilization of cesium and iodine into Cs 3 Bi 2 I 9 perovskite-silica composites and core-shell waste forms with high waste loadings and chemical durability

Cs$_3$Bi$_2$I$_9$, a defect perovskite derivative, is a potential host phase to immobilize iodine and cesium with high waste loadings. In this work, two strategies were explored to form Cs$_3$Bi$_2$I$_9$-silica composites and a core-shell structure in order to improve chemical durability of waste form materials meanwhile maintaining high waste loadings. Cs$_3$Bi$_2$I$_9$ loadings as high as 70 wt.% were incorporated into a silica matrix to form silica-ceramic composites, and 20 wt.% Cs$_3$Bi$_2$I$_9$ was encapsulated into silica to form a core–shell structure by low temperature spark plasma sintering. Chemical durability of the composite and core-shell waste forms was evaluated by semi-dynamic leaching experiments, and Cs and I were incongruently released from waste form matrices. A BiOI alteration layer formed, acting as a passivation layer to reduce the release of radionuclides. The long-term iodine release rate was low (30 mg m$^{-2}$ day$^{-1}$) for the 70 wt.%Cs$_3$Bi$_2$I$_9$–silica composite leached in deionized water at 90 °C, which can be further reduced to 5 × 10$^{-3}$ mg m$^{-2}$ day$^{-1}$ for the 20 wt.% core-shell structure. This work highlights a robust way to immobilize the highly mobile radionuclides with high waste loadings through encapsulation into durable matrices and a surface passivating mechanism that can greatly reduce the elemental transport from waste form materials and significantly enhance their chemical durability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗