Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graphite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

HDG-1 Graphite Preirradiation Data Package Report

This report documents all pre-irradiation examination material-property measurement data for graphite specimens that are going to be used within the first high dose graphite (HDG) -1 irradiation capsule. The two new HDG capsules signify a major change to the AGC Experiment. HDG-1 and HDG-2 will replace the last two Advanced Graphite Creep (AGC) capsules (AGC-5 and AGC-6) which were designed to irradiate graphite at the extreme upper operational temperatures for a very-high-temperature reactor (VHTR) design, 1100°C. These very high temperature AGC-5 and AGC-6 capsules have been repurposed to re-irradiated specimens (from AGC-2, AGC-3, and AGC-4) at the lower temperatures of 600°C and 800°C. HDG-1 will be irradiated at 600°C and HDG-2 will be irradiated at 800°C. By re-irradiating the previous AGC specimens a total maximum neutron dose of around 15 dpa (displacements per atom) can be achieved for all major graphite grades at irradiation temperatures of 600°C and 800°C. Specimens in the HDG-1 capsule are made up of previously irradiated specimens from the AGC-2 capsule and unirradiated specimens prepared for the now discontinued AGC-5 capsule. Utilizing the irradiated specimens, a maximum neutron dose of around 15 dpa is anticipated. These new maximum dose levels will provide irradiated material property data over a total neutron dose range of 1-15 dpa at a temperature of 600°C when combined with the previous AGC-1 and AGC-2 irradiation data. This will provide quantitative data necessary for predicting the irradiation behavior and operating performance of new nuclear graphite grades for use within high temperature reactor designs. Similar to previous AGC test trains, HDG-1 includes the major graphite grades (IG-110, NBG-17, NBG-18, PCEA, and 2114) as well as adding the very fine-grain grade IG-430 which is of interest to the Molten Salt Reactor (MSR) designs. Also new to the HDG-1 capsule are 90 smaller geometry specimens designated as pencil specimens. These specimens take up only one third the space of a standard creep size specimen. This increased number of specimens will enhance property measurement statistics because they will provide 3 times the control specimen data at a position that would otherwise only have a single measurement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Microstructural Characterization of Al 4 C 3 in Aluminum-Graphite Composite Prepared by Electron-Beam Melting

We prepared graphite infused aluminum composites by electron-beam vacuum melting and electromagnetic stirring with 0% and 4wt% graphite addition. Bulk density of 2.69 g/cm 3 was measured for samples with 0% graphite addition (AlCv0) and 2.66 g/cm 3 for samples with 4 wt% graphite addition (AlCv4). Both are >99% of their theoretical values. X-ray diffraction indicated that AlCv0 is phase pure, while the AlCv4 sample is a composite consisting of aluminum, Al 4 C 3 , and graphite. Electron microscopy and energy dispersive X-ray spectroscopy revealed pockets of carbon rich phase of 10 to 50 μm in sizes dispersed in the Al matrix in AlCv4. Scanning transmission electron microscopy (STEM) showed that Al 4 C 3 crystallites of 1-2 μm sizes that are mostly located near the outer shell of the pockets of carbon rich phase and with undissolved graphite at the center. Thermal conductivity of 107.8 W/m·K was measured for the AlCv4 and 226.7 W/m·K for the AlCv0. Our work demonstrated the feasibility of producing pore-free high density graphite infused aluminum composite materials by electron-beam melting and electromagnetic stirring in vacuum.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Engineering Nucleation Kinetics of Graphite Nodules in Inoculated Cast Iron for Reducing Porosity

Inoculation of cast iron with spherical graphite (SGI) controls nucleation kinetics of graphite nodules and is used for improving casting performance and eliminating solidification micro-porosity. In this study, thermodynamic simulations were used to design inoculants. Thermal and chemical stability of different potential heterogeneous nuclei formed in the melt above the liquidus temperature and in the mushy zone during solidification was predicted. Several inoculation treatments of SGI were performed in laboratory heats. An automated SEM/EDX analysis was applied to examine the graphite nodule size distribution and the family of the non-metallic inclusions in the experimental castings. The data were used to reconstruct a relative graphite nodule nucleation rate in the castings. It was shown that the graphite nodule nucleation kinetics in the castings were significantly different from those predicted by classical nucleation models. In inoculated SGI, the observed bi-modal distribution of graphite nodules was related to a continuous nucleation that occurred towards the end of solidification. The origin of the continuous nucleation and the possibility of engineering graphite nodules nucleation kinetics to control SGI casting soundness by inoculation are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fullerene-like defects in high-temperature neutron-irradiated nuclear graphite

Irradiation-induced defect evolution in graphite is particularly important for its application in graphite-moderated nuclear reactors. The evolution of defects directly influences macroscopically observed property changes in irradiated nuclear graphite which, in turn, can govern the lifetime of graphite components. This article reports novel defect structures and the irradiation response of microstructural features occurring in high-temperature irradiated nuclear graphite IG-110. High resolution transmission electron microscopy (HRTEM) was used to characterize specimens neutron-irradiated at a high temperature (≥ 800°C) at doses of 1.73 and 3.56 atomic displacements per atom (dpa). Concentric shelled and fullerene-like defects were found to result in swelling along the c-axis and contraction along the a/b-axis of crystallites. Furthermore, such defects are shown to occur within, and partially fill, Mrozowski cracks prior to turnaround dose. In addition, in situ TEM under similar irradiation conditions was used to capture the real-time dynamic evolution of defects, providing unambiguous analysis of the evolution of the graphite structures during irradiation. Here, the results suggest the mainstream theory for radiation damage in nuclear graphite (which assumes additional basal plane formation as the sole reason) to be an incorrect interpretation of defect evolution contributing to irradiation-induced property changes at higher temperatures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Oxidation behaviors of matrix-grade graphite during water vapor ingress accidents for high temperature gas-cooled reactors

Water ingress into cores of high temperature gas-cooled reactors (HTGRs) can cause serious safety problems in graphitic components, especially for matrix graphite, which is more vulnerable than nuclear graphite. Here in this study, oxidation behaviors of a matrix-grade graphite, ARB-B1, were investigated under simulated water ingress accidental conditions. The oxidation tests were conducted in water vapor/helium mixed atmospheres at elevated temperatures up to 1200 °C. Oxidation rates and activation energy were evaluated by mass loss measurements. The activation energy was 121.5 kJ/mol in the considered temperature range, indicating only one oxidation regime-in-pore diffusion assisted by cracks. The cracks originated from the fabrication process, acting as penetration paths for the oxidant, played an important role in the oxidation behaviors. Ungraphitized binder oxidation occurred at all temperatures, while apparent oxidation of filler particles started from 1100 °C. Moreover, oxidation effects on compressive properties and hardness of the matrix graphite were discussed in terms of oxidized microstructures. This first detailed study on matrix graphite oxidation in water vapor provides important kinetics knowledge and microstructural and mechanical data for accidental scenarios of HTGRs as well as for development of new matrix graphite materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Molten salt electrochemical upcycling of CO 2 to graphite for high performance battery anodes

The efficient transformation of CO 2 into a value-added material is a potential strategy to help mitigate climate effects caused by CO 2 emissions. One potential CO 2 conversion product is graphite which is an important and versatile material extensively used in many applications including as an anode for lithium-ion batteries (LIBs). Commercial graphite, however, is traditionally synthesized via the energy intensive Acheson process (>3000 °C) and the performance of such graphite can be limited under fast charging conditions which is important for vehicle electrification. We report the electrochemical transformation of CO 2 to highly crystalline nano-graphite with a controlled microstructure in a carbonate molten salt at 780 °C. The use of a nickel foam electrode and controlled electrochemical parameters during the molten salt conversion process yielded pure graphite at a lower temperature compared to the Acheson process. Moreover, when investigated as an anode material for LIBs, the CO 2 -converted graphite exhibited high reversible capacity, long cycle life, and excellent rate capability even under fast charging conditions. This process provides a way to potentially reduce carbon emissions through the utilization of waste CO 2 by converting it into value-added graphite suitable for fast charging, high-energy-density batteries for vehicle electrification.

25 ENERGY STORAGE↗
DOE OSTI2020

The transformation of diamond to graphite: Experiments reveal the presence of an intermediate linear carbon phase

Natural diamonds that have been partially replaced by graphite have been observed to occur in natural rocks. While the graphite-to-diamond phase transition has been extensively studied the opposite of this (diamond to graphite) remains poorly understood. We performed high-pressure and temperature hydrous and anhydrous experiments up to 1.0 GPa and 1300 °C using Amplex premium virgin synthetic diamonds (20–40 μm size) as the starting material mixed with Mg(OH) 2 as a source of H 2 O for the hydrous experiments. The experiments revealed that the diamond-to-graphite transformation at P = 1.0 GPa and T = 1300 °C was triggered by the presence of H 2 O and was accomplished through a three-stage process. Stage 1: diamond reacts with a supercritical H 2 O producing an intermediate 200–500 nm size “globular carbon” phase. This phase is a linear carbon chain; i.e. a polyyne or carbyne. Stage 2: the linear carbon chains are unstable and highly reactive, and they decompose by zigzagging and cross-linking to form sp 2 -hybridized structures. Stage 3: normal, disordered, and onion-like graphite is produced by the decomposition of the sp-hybridized carbon chains which are re-organized into sp 2 bonds. Our experiments show that there is no direct transformation from sp 3 C-bonds into sp 2 C-bonds. Our hydrous high-pressure and high-temperature experiments show that the diamond-to-graphite transformation requires an intermediate metastable phase of a linear hydrocarbon. This process also provides a simple mechanism for the substitution of other elements into the graphite structure (e.g. H, S, O).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multiscale characterization and comparison of historical and modern nuclear graphite grades

Beginning with Chicago Pile I, graphite has been used as a moderator material in nuclear power stations and is considered a potential material for use in future Generation IV advanced reactors. The microstructure of graphite is responsible for much of its mechanical and thermo-physical properties, and how it responds to irradiation. To understand graphite microstructure, it is necessary to understand its porosity at the macro- and micro-scales; and to understand its porosity, it is necessary to characterize the morphological connectivity of the void content and the two main phases of graphite: filler and binder. Here, using several microscopy and analytical techniques, a detailed examination of the heterogeneity, microstructure and pore structure of different graphite grades and their binder and filler phases is presented. Significant differences were found between coarser and finer nuclear grades. Coarse grades have a more diverse range of filler particles, pores and thermal cracks. Finer grades have a more well-defined pore size distribution, fewer variations of filler particles sizes and do not contain as many large thermal cracks. Fine grades tend to have a well-connected network of pores whereas coarser grades contain a larger content of closed porosity. The framework developed within this work can be applied and used to assess the various graphite grades that would down-select materials for specific use in graphite moderated reactor designs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Catalyzed oxidation of IG-110 nuclear graphite by simulated fission products Ag and Pd nanoparticles

To evaluate the stability of nuclear materials in high temperature gas reactors under air ingress conditions, catalytic oxidation of IG-110 graphite by two simulated fission products, metallic Pd and Ag, was studied in oxidative atmosphere and at temperatures up to 1000°C using an integrated furnace, mass spectroscopy and infrared spectroscopy system. Transmission electron microscopy and X-ray diffraction studies show that Pd and Ag nanoparticles were successfully introduced onto powdery IG-110 graphite through an impregnation and subsequent heat-treatment process. The combined mass spectroscopy and infrared spectroscopy methods allow simultaneous analysis of two gaseous products, CO and CO 2 , and separate measurements of activation energy for their formation reactions. It was found that the introduction of Pd or Ag to IG-110 graphite substantially catalyzed the oxidation of graphite, characteristic of decreased onset temperatures for the oxidation of graphite. Moreover, the catalytic effects by Pd and Ag are considerably different based on measured concentration ratios of CO 2 to CO as a function of oxidation temperatures. Ag makes the graphite oxidation commence at approximately 400°C with CO 2 being the dominant product. In contrast, Pd significantly increases the concentration ratio of CO 2 to CO at temperatures higher than approximately 690°C, although it decreases the onset temperature for the oxidation reaction to around 525°C. To understand the catalytic difference, the mechanism of the graphite oxidation was discussed based on the changes of surface oxygen species on Ag and Pd.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Insights into the Enhanced Reversibility of Graphite Anode Upon Fast Charging Through Li Reservoir

Increasing the charging rate and reducing the charging time for Li-ion batteries are crucial to realize the mainstream of electric vehicles. However, it is formidable to avoid the Li plating on graphite anode upon fast charging. Despite the tremendous progress in Li detection techniques, the fundamental mechanism of Li plating and its chemical/electrochemical responses upon cycling still remains elusive. Herein, we present a comprehensive electrochemical method to investigate the fast charging behavior of graphite electrode. A detailed analysis is directed toward understanding the changes in phase, composition, and morphology of the fast-charged graphite. By applying a resting process, we scrutinize the further reactions of the plated Li, which readily transforms into irreversible (dead) Li. We further develop a modified graphite electrode with a thin Ag coating as the Li reservoir. The plated Li can be "absorbed" by the Ag layer to form the Li-Ag solid solution that suppresses the formation of dead Li and provides structural stability, thus promoting the further lithiation of graphite and enhancing the reversibility. Here this work not only provides additional insights into the fast charging behavior of graphite electrode but also demonstrates a potential strategy to improve the fast charging performance of graphite anode.

25 ENERGY STORAGE↗
DOE OSTI2024

Self-terminating, heterogeneous solid–electrolyte interphase enables reversible Li–ether cointercalation in graphite anodes

Ether solvents are suitable for formulating solid-electrolyte interphase (SEI)-less ion-solvent cointercalation electrolytes in graphite for Na-ion and K-ion batteries. However, ether-based electrolytes have been historically perceived to cause exfoliation of graphite and cell failure in Li-ion batteries. In this study, we develop strategies to achieve reversible Li–solvent cointercalation in graphite through combining appropriate Li salts and ether solvents. Specifically, we design 1M LiBF 4 1,2-dimethoxyethane (G1), which enables natural graphite to deliver ~91% initial Coulombic efficiency and >88% capacity retention after 400 cycles. We captured the spatial distribution of LiF at various length scales and quantified its heterogeneity. The electrolyte shows self-terminated reactivity on graphite edge planes and results in a grainy, fluorinated pseudo-SEI. The molecular origin of the pseudo-SEI is elucidated by ab initio molecular dynamics (AIMD) simulations. The operando synchrotron analyses further demonstrate the reversible and monotonous phase transformation of cointercalated graphite. Our findings demonstrate the feasibility of Li cointercalation chemistry in graphite for extreme-condition batteries. The work also paves the foundation for understanding and modulating the interphase generated by ether electrolytes in a broad range of electrodes and batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Benchmark of Neutron Thermalization in Graphite Using a Pulsed Slowing-Down-Time Experiment

A benchmark has been developed using a pulsed slowing-down-time experiment to isolate the thermalization process in graphite. The experiment was conducted at the Oak Ridge Electron Linear Accelerator facility at Oak Ridge National Laboratory, and it measured the time spectrum of neutrons leaking from a graphite pile during slowing down and thermalization within graphite. Simulations of the benchmark experiment were performed using the MCNP6.1 Monte Carlo code and the ENDF/B-VII.1 and ENDF/B-VIII.0 cross-section databases. The benchmark provides a time spectrum (i.e., time-dependent counts in a detector) that allows for validation of the graphite thermal scattering libraries (TSLs). The impact on the simulations using a suite of graphite TSLs was compared with the experimental results. Given the density of nuclear graphite, the TSL corresponding to graphite with 30% porosity, as implemented in ENDF/B-VIII.0, was found to most accurately represent the measured time spectrum corresponding to the thermal energy range with an average deviation of ±1.7%.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2019

Thermoelectric Properties of Sb 2 Te 3 -Based Nanocomposites with Graphite

Antimony-telluride-based nanocomposite samples containing different weight fractions of graphite (Sb 2 Te 3 + x% graphite, where x = 0.0, 0.5, 1.0, and 2.5%) are synthesized and studied. The samples are produced by a solid-state reaction with the use of a ball mill. X-ray diffraction measurements show that the Sb 2 Te 3 phase is present in the nanocomposites. All of the diffraction peaks are identified as corresponding to the rhombohedral structure of symmetry R 3-bar m. No additional peaks related to graphite are observed because of its low content. Moreover, the X-ray data show the insolubility of graphite in Sb 2 Te 3 : the peaks related to Sb 2 Te 3 remain unchanged upon the addition of graphite. The thermal conductivity, thermoelectric power, and resistivity of the samples are studied in the temperature range 80 K ≤ T ≤ 320 K. The thermal conductivity k of the nanocomposite decreases several times compared to the thermal conductivity of single-crystal Sb 2 Te 3 and reaches k ≈ 0.95 W m -1 K -1 at x = 0.5%. The parameter k unsteadily depends on the content of graphite. The thermoelectric power of the nanocomposites with graphite at x = 1.0% is higher compared to that of nanostructured Sb 2 Te 3 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

AGC-5 Graphite Pre-irradiation Data Analysis Report

This report documents all preirradiation examination material property measurement data for the graphite specimens which were to be used within the fifth Advanced Graphite Capsule (AGC-5) irradiation capsule. The AGC-5 capsule was to be the fifth in six planned irradiation capsules comprising the AGC test series that was designed to irradiate graphite specimens in a temperature range of 600 – 1100°C and medium dose levels to 7 dpa. This would provide quantitative data necessary for predicting the irradiation behavior and operating performance of new nuclear graphite grades for use within very high temperature reactor designs (VHTR). However, due to the lack of commercial interest in building a VHTR design within the USA, the graphite irradiation program was redirected by DOE Advanced Reactor Technology (ART) to re-irradiate the existing specimens from AGC-1 through AGC-4 in the remaining AGC capsules to achieve higher dose levels (15 dpa) at a lower irradiation temperature range (600-800°C). These new irradiation capsules have been designated as the High Dose Graphite (HDG) capsules. This new low temperature, high dose irradiation program favors the current high temperature reactor (HTR) design of interest to the US commercial nuclear community. This report summarizes the measurements from material property tests on the designated AGC-5 specimens. Similar to past AGC runs the specimens were categorized as major graphite grades (IG-110, NBG-17, NBG-18, PCEA and 2114), smaller experimental samples (thermal diffusivity sized specimens of major grades). It is anticipated that some AGC-5 specimens may be required for use within the new HDG-1 capsule. Any specimens from this pre-irradiation testing campaign will be identified in the future HDG-1 Pre-Irradiation Data Report. AGC-5 specimen testing was conducted at Idaho National Laboratory (INL) from December 2015 to February 2018.

(AGC)↗
DOE OSTI2022

Thermal Neutron Scattering Cross Sections for Graphitic Amorphous Carbon

Carbon materials are commonly found in both nuclear reactors and experimental systems. Various carbon structures occur in nuclear applications ranging from crystalline and nuclear graphite to the amorphous carbon seen in next-generation advanced reactor designs. Amorphous carbon is based on a randomized graphite-like structure and offers the unique ability to disperse impurities throughout the bulk composition. A graphite-like amorphous carbon system was modeled using the classical molecular dynamics (MD) code LAMMPS (Large-scale Atomic/Molecular Massively Parallel Simulator). An improved version of the temperature-dependent Adaptive Intermolecular Reactive Empirical Bond Order (AIREBO) potential was used to model the carbon-carbon atomic interactions for the temperature at 300 K along with densities 1.60, 1.70, 1.85, and 2.23 g/cm 3 . From the normalized velocity autocorrelation function (VACF), the phonon density of state (DOS) was then calculated as the Fourier transform of the normalized VACF. This DOS was then used as the primary input for the evaluation of the thermal scattering law (TSL, i.e. S(α,β)) and associated neutron thermal scattering cross sections. The TSL was analyzed using the Full Law Analysis Scattering System Hub (FLASSH). The amorphous structure results in shifts of the phonon DOS to lower energy modes than typically displayed for ideal crystalline graphite. This impact on the DOS is directly reflected in the TSL. Furthermore, the typical features and the optical graphitic peak at 0.25 eV for the ideal graphite DOS disappear for graphite-like amorphous carbon, which shows good agreement with the expected structure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Highly Crystalline Graphite Synthesis from Coal with a Sustainable Process

Synthetic graphite is made predominantly from a petroleum-derived needle coke using the Acheson method. This involves heating the needle coke at elevated temperatures of ~ 3000 °C for more than 7 days. High-temperature heating is the most technically challenging, expensive, and energy-intensive aspect of graphite manufacturing. We will present a strategy for synthesizing high-quality graphite powder from coal using a low-temperature catalytic graphitization process. The use of a catalyst drops the processing temperatures to 1500 °C and processing times to a few hours. The graphite produced with this process has been characterized and has been shown to have comparable physical/chemical properties with commercially sourced graphite materials. We will also present a sustainable method to recover and reuse the catalyst and acid used to retrieve the catalyst. This overcomes a long-standing technical hurdle associated with using catalysts for manufacturing graphite.

crystalline graphite powder↗
DOE OSTI2020

Graphite Licensing (ASME) and Testing (ASTM) Technical Assistance

DOE ART Graphite R&D program is currently involved in developing the structural code for licensing the new High Temperature Reactor (HTR) designs through the ASME Boiler Pressure Vessel Code (BPVC). The basic structural design code for graphite core components has been written, approved, and within the BPVC since 2012. However, several areas within the graphite code remain to be improved, specifically the addition of material property changes resulting from environmental degradation (neutron flux and oxidation). The incorporation of this data, which can significantly affect the graphite components and alter the structural integrity of the core during operation, is proving to be an important activity. How this data will be incorporated within the code and how it will be used for license applications will be critical to a number of HTR applicants in the future. These modifications to the code must take into account the unique irradiation and oxidation response of the wide spectrum of available nuclear graphite grades currently under consideration for HTR applications. Additionally, the ASME BPVC requires material property testing within the expected operational conditions of the HTR core including neutron radiation flux, elevated temperatures, and after chronic/acute oxidation of the graphite components. Currently, no standardized graphite testing methods are approved for these environmental conditions. New American Society for Testing and Materials (ASTM) standardized tests for elevated temperature testing, small sample testing, and testing after oxidation must be developed to support the requirements within the ASME code.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Graphite Specimen Mass Measurements for NESHAP Calculations

The Advanced Graphite Creep (AGC) experiments were designed to irradiate various types of graphite specimens to gain an understanding of how the physical and thermal properties of the graphite change. The graphite specimens are machined from nuclear grade graphite that is very pure relative to other graphite types. However, it still contains parts per million (PPM) levels of metal contaminants that are dispersed throughout it. During irradiation in the Advanced Test Reactor (ATR) these metal contaminants become activated resulting in the graphite specimens being classified as a radioactive material. Following their irradiation, a variety of measurements and experiments are performed on these specimens that require them to be heated above 100°C.Whenever a radioactive material is heated to above 100°C the National Emission Standards for Hazardous Air Pollutants (NESHAP) calculations require the activity content, in Curies, of the isotopes that could potentially be released to the environment. The purpose of this ECAR is to document the method by which the mass loss of each sample is determined and how the isotopic content of this mass loss is determined.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗