Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “glass melting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Structure-mechanical properties correlation in bulk LiPON glass produced by nitridation of metaphosphate melts

The glassy solid electrolyte Lithium phosphorous oxynitride (LiPON) has been widely researched in thin film solid state battery format due to its outstanding stability when cycled against lithium. In addition, recent reports show thin film LiPON having interesting mechanical behaviors, especially its ability to resist micro-scale cracking via densification and shear flow. Here, in the present study, we have produced bulk LiPON glasses with varying nitrogen contents by ammonolysis of LiPO 3 melts. The resulting compositions were determined to be LiPO 3-3z/2 N z , where 0 ≤ z ≤ 0.75, and the z value of 0.75 is among the highest ever reported for this series of LiPON glasses. The short-range order structures of the different resulting compositions were characterized by infrared, Raman, 31 P magic angle spinning nuclear magnetic resonance, and X-ray photoelectron spectroscopies. Instrumented nano-indentation was used to measure mechanical properties. It was observed that similar to previous studies, both trigonally coordinated (N t ) and doubly bonded (N d ) N co-exist in the glasses in about the same amounts for z ≤ 0.36, the limit of N content in most previous studies. For glasses with z > 0.36, it was found that the fraction of the N t increased significantly while the fraction of N d correspondingly decreased. The incorporation of nitrogen increased both the elastic modulus and hardness of the glass by approximately a factor of 1.5 when N/P ratio reaches 0.75. At the same time, an apparent embrittlement of the glass was observed due to nitridation, which was revealed by nanoindentation with an extra sharp nanoindenter tip.

25 ENERGY STORAGE↗
DOE OSTI2021

Characterization of the Sulfur-Saturated Melt Versions of the HFG1 Study Glasses

The U.S. Department of Energy (DOE) is responsible for building the Hanford Tank Waste Treatment and Immobilization Plant (WTP) at the Hanford Site in Washington to remediate 55 million gallons of radioactive waste that is temporarily stored in 177 underground tanks. The Office of River Protection (ORP) has requested that the Savannah River National Laboratory (SRNL) contribute to current glass studies to support successful startup of the WTP, due to SRNL’s recognized capabilities and expertise for glass waste form development. As part of this effort, the Pacific Northwest National Laboratory (PNNL) is developing, batching, and fabricating simulated high-level waste (HLW) glasses to generate the associated property data needed to validate or identify areas of potential characterization improvements in the current glass property/ composition models. Currently, the models cover only a small fraction of the waste compositions projected in the Hanford tank farm; therefore, the models must be expanded to include high fluoride compositions to successfully complete the WTP mission. SRNL support of this work is defined in the Task Technical and Quality Assurance Plan (TTQAP). This report provides results from the chemical analyses of a series of sulfur-saturated melt (SSM) versions of simulated nuclear waste glasses fabricated at PNNL. The glasses were selected as part of a broader study of the influence of glass composition on chemical durability, sulfur retention, and other properties. The glasses were designated the High Fluoride Glasses-1 (HLG1).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Sol–gel synthesis of iodosodalite precursors and subsequent consolidation with a glass binder made from oxides and sol–gel routes

Radioiodine accumulates in aqueous solutions and off-gas streams during nuclear fuel reprocessing due to its solubility in aqueous solutions and volatility, respectively. Additionally, radioiodine is highly mobile in geological environments and iodine-129 has been found to be one of the largest long-term contributors to chronic dose to humans in scenarios of radionuclide migration from geological repositories. Most of the radioiodine can be captured during fuel reprocessing in off-gas streams using solid sorbents and scrubbing solutions. Once iodine is captured, it must be stored in a durable form for eventual disposal. Iodosodalite has been investigated as a waste form for radioiodine, however these synthesis processes typically result in mixed products and iodine volatilization during consolidation. Therefore, this paper proposes a novel approach to synthesizing iodosodalite utilizing a sol-gel method. This method was chosen to lower processing temperatures and improve product yield. Preliminary experiments conducted to determine the viability of this synthetic method are presented. Additionally, consolidation of sol-gel derived iodosodalite with a glass-binder was explored using three different methods: 1) incorporating the glass-binder during gel preparation using alkoxide precursors; 2) separately preparing the glass binder using a sol-gel method; and 3) separately preparing the glass-binder using a melt-quench technique. Glass-bonded iodosodalite was successfully synthesized using these novel sol-gel approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Durability testing of actual Hanford waste glasses and their non-radioactive simulant glasses

The low-activity waste (LAW) fraction of Hanford tank waste will be converted to glass at the Waste Treatment and Immobilization Plant (WTP) and disposed on the Hanford site. The chemical durability of LAW glasses has been researched for decades to satisfy contract requirements. Most LAW glass durability data has been generated on non-radioactive simulant glasses fabricated via crucible melts. These non-radioactive glasses were chosen due to safety and cost reasons with confidence that radioactive waste glasses would exhibit similar behavior. To reduce the risk of significant differences in laboratory test response data between WTP melter waste glass and simulant glass, Product Consistency Tests (PCT, i.e., ASTM C1285-21) and Environmental Protection Agency (EPA) 1313 durability tests were performed on actual and simulant LAW glasses fabricated using laboratory-scaled melters. Actual and simulant glass durability test results are presented and statistically compared. Finally, differences in test responses were found to be within experimental uncertainty.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Structures of fluoride containing aluminosilicate low activity nuclear waste glasses: A molecular dynamics simulations study

Fluorine and other halides commonly exist in nuclear waste forms, and due to their volatile nature, halide retention poses an issue affecting waste loading during vitrification. The compositional effect on fluorine incorporation in aluminosilicate glasses is investigated through molecular dynamics simulations. Oxygen and fluorine coordination numbers around glass former and modifier cations, bond angle distributions, and medium range structure features such as Q n distributions, ring size distributions and neutron diffraction structure factors were calculated. It was found that fluorine has higher preference to bond to Ca 2+ than to Na + , both in the melt and the glass, and there is no Si-F bond formation in the glass but they do exist in the melt. Consequently, CaO for Na 2 O substitution can be an effective way to help fluorine retention without significantly changing the glass chemistry. Furthermore, these results thus provide insights on fluorine incorporation in the aluminosilicate nuclear waste glasses and the strategy on how to improve fluorine retention both in the glass and the melt.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of the Sulfur-Saturated Melt Version of the EMHQ-LBE-04-B Glass

This report provides the results from the chemical analyses of the sulfur-saturated melt version of the EMHQ-LBE-04-B glass. These data will be used in the development, validation, and implementation of enhanced property/composition models for waste glass vitrification at Hanford. Chemical analyses were performed on a representative sample of the sulfur-saturated melt version of the glass to allow for comparisons with the targeted composition as well as the measured composition of the quenched glass. The relative differences between the targeted and measured concentration of Na 2 O and SO 3 in the glass were greater than ±10%. The wash solutions contained mainly sodium and sulfate ions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Conversion degree and heat transfer in the cold cap and their effect on glass production rate in an electric melter

A predictive model of melt rate in waste glass vitrification operations is needed to inform melter operations during normal and off-normal operations. This paper describes the development of a model of the cold cap (the reacting melter feed floating on molten glass in a glass melter) that couples heat transfer with the feed-to-glass conversion kinetics. The model was applied to four melter feeds designed for high-level and low-activity nuclear waste feeds using the material properties, either measured or estimated, to obtain temperature and conversion distribution within the cold cap. The cold cap model, when coupled with a computational fluid dynamics model of a Joule-heated glass melter, allows the prediction of the glass production rate and power consumption. The results show reasonable agreement with the melting rates measured during pilot-scale melter tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Revealing the relationship between liquid fragility and medium-range order in silicate glasses

Despite decades of studies, the nature of the glass transition remains elusive. In particular, the sharpness of the dynamical arrest of a melt at the glass transition is captured by its fragility. Here, we reveal that fragility is governed by the medium-range order structure. Based on neutron-diffraction data for a series of aluminosilicate glasses, we propose a measurable structural parameter that features a strong inverse correlation with fragility, namely, the average medium-range distance (MRD). We use in-situ high-temperature neutron-scattering data to discuss the physical origin of this correlation. We argue that glasses exhibiting low MRD values present an excess of small network rings. Such rings are unstable and deform more readily with changes in temperature, which tends to increase fragility. These results reveal that the sharpness of the dynamical arrest experienced by a silicate glass at the glass transition is surprisingly encoded into the stability of rings in its network.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Thermodynamics of Liquid Immiscibility in Iron-Silicate Melt Systems: A Study of Nuclear Fallout Glass

In a ground-interacting nuclear explosion, elements derived from environmental and anthropogenic material, such as iron, silicon, and aluminum, can be incorporated into the fireball. When significant amounts of metals are entrained, the resulting melt may display immiscible textures. The composition of these textures is a record of the temperature of formation and cooling rates (or thermodynamic stability) of the melts and can provide unique constraints on the early cooling conditions of these events. Here, a thermodynamic approach using calculated phase diagrams, the CALPHAD method, is used to predict temperature and composition ranges where stable liquid immiscibility might result in the textures observed in nuclear fallout glass. Sensitivity of the immiscibility to the presence of relative Al, Ca, and Mg content is also explored and compared to fallout samples, and partition coefficients are introduced to understand the preferred distribution of components into each liquid phase.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microgravity effects on nonequilibrium melt processing of neodymium titanate: thermophysical properties, atomic structure, glass formation and crystallization

The relationships between materials processing and structure can vary between terrestrial and reduced gravity environments. As one case study, we compare the nonequilibrium melt processing of a rare-earth titanate, nominally 83TiO 2 -17Nd 2 O 3 , and the structure of its glassy and crystalline products. Density and thermal expansion for the liquid, supercooled liquid, and glass are measured over 300–1850 °C using the Electrostatic Levitation Furnace (ELF) in microgravity, and two replicate density measurements were reproducible to within 0.4%. Cooling rates in ELF are 40–110 °C s -1 lower than those in a terrestrial aerodynamic levitator due to the absence of forced convection. X-ray/neutron total scattering and Raman spectroscopy indicate that glasses processed on Earth and in microgravity exhibit similar atomic structures, with only subtle differences that are consistent with compositional variations of ~2 mol. % Nd 2 O 3 . The glass atomic network contains a mixture of corner- and edge-sharing Ti-O polyhedra, and the fraction of edge-sharing arrangements decreases with increasing Nd 2 O 3 content. X-ray tomography and electron microscopy of crystalline products reveal substantial differences in microstructure, grain size, and crystalline phases, which arise from differences in the melt processes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Structure of molten ytterbium aluminum garnet

Rare earth aluminum garnets are important materials in optical, dielectric, and thermal barrier applications. To advance the understanding of their melt processing and glass forming ability, we report the atomic structure of molten Yb 3 Al 5 O 12 over 1770–2630 K, which spans the equilibrium and supercooled liquid regimes. The melt density at T m = 2283 K is 5.50 g cm –3 , measured via silhouette imaging of electrostatically levitated drops over 1010–2420 K. Four separate structure measurements were made with aerodynamically levitated melts using x-ray and neutron diffraction with isotope substitution of Yb ( 172 Yb, 174 Yb, or nat Yb). Empirical potential structure refinement models were developed, which are in excellent agreement with the experiments. Coordination environments for Al–O are predominantly 4- and 5-coordinate, with a mean coordination of n AlO = 4.43(8), while Yb–O environments mostly range from 5- to 8-coordinate, with n YbO = 6.26(8). The cation–oxygen polyhedra are connected primarily by corner-sharing, with edge-sharing constituting up to ~1/3 of the connectivity among polyhedra with Yb or higher-coordinated Al–O. Structurally, the –Al–O– network in molten Yb 3 Al 5 O 12 appears conducive to glass formation: n OAl = 1.85(3), there are 1.86 AlO x –AlO x connections per Al atom (e.g., a mixture of Q 3 and Q 4 units), and the modal ring size is six cations. These characterize a network that is somewhat less constrained compared to SiO 2 glass, yet Yb 3 Al 5 O 12 cannot be quenched into crystal-free glass. Here, aluminum garnet compositions with larger rare earth cations do form glass, so these characterizations help reveal the structural characteristics corresponding to the limit of glass forming ability in rare earth aluminates.

36 MATERIALS SCIENCE↗
DOE OSTI2026

From bulk to surface: Structure and dynamics of amorphous alumina from deep potential molecular dynamics

Understanding the atomic-scale structure and dynamics of amorphous oxide surfaces is essential for interpreting their chemical reactivity, mechanical stability, and interfacial behavior, yet direct experimental characterization remains challenging. We employ Deep Potential (DP) molecular dynamics to generate large-scale, ab initio -quality models of amorphous Al 2 O 3 bulk glasses and melt-quenched free surfaces, enabling a quantitative analysis of both structure and relaxation dynamics with statistical confidence inaccessible to direct ab initio simulation. The trained DP model reproduces experimental liquid and glass structure, captures the cooling-rate dependence of the bulk glass transition, and corrects systematic biases in the polyhedral populations predicted by widely used classical force fields. At the free surface, mass density recovers to bulk values over ~10 Å, while local coordination requires a slightly wider subsurface region to fully converge. The outermost layer is oxygen-enriched, exhibits altered polyhedral connectivity with contracted Al–O bonds, and hosts a broad population of under-coordinated motifs (notably AlO 3 and OAl 2 ) whose abundances are governed by glass stability. These under-coordinated surface motifs exhibit distinct vibrational signatures and occur as locally paired Lewis acid and Brønsted base sites consistent with bond-valence compensation, yet remain spatially dispersed rather than aggregating into extended clusters. Despite this pronounced structural heterogeneity, surface relaxation and the glass-transition temperature remain comparable to their bulk counterparts, suggesting that the disordered surface is kinetically stable once formed. Together, these results establish a molecular-level picture of amorphous alumina surfaces and demonstrate the capability of machine-learned potentials to resolve structure–property relationships in disordered oxide interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

The effect of composition, temperature and pressure on the oxidation state and coordination environment of copper in silicate melts

Copper is a redox variable element that may occur as Cu 0 , Cu + , and Cu 2+ in the Earth’s crust. The oxidation state will affect its partitioning between coexisting minerals, melts and fluids and hence its behaviour in magmatic processes. Copper bearing silicate glasses were quenched from melts with 23 synthetic compositions (19 CaO-Na 2 O-MgO-Al 2 O 3 -SiO 2 (CNMAS), two “granites” containing K 2 O ± H 2 O, and Fe-bearing “MORB” and “andesite”) equilibrated at oxygen fugacities (fO 2 ), expressed in log units relative to the fayalite-magnetite-quartz (FMQ) buffer, ranging from −0.7 to 14, temperatures from 900 to 1500 °C and pressures from 0 to 2.5 GPa. Cu K-edge X-ray absorption near edge structure (XANES) spectra were recorded from the glasses and a pre-edge feature in the XANES spectra was found to scale with the proportion of Cu + . Cu + /ΣCu (where ΣCu = Cu + + Cu 2+ ) was quantified by fitting the intensity of the pre-edge feature as a function of fO 2 to the thermodynamically expected relationship. Cu + /ΣCu was found to only weakly depend on melt composition, with more basic melts (e.g., basalts rather than granites) preferentially stabilising Cu 2+ . Increasing temperature stabilises Cu + , while increasing pressure had little effect on Cu + /ΣCu in CNMAS melts but preferentially stabilised Cu 2+ in granite melts. Cu + /ΣCu can be predicted in silicate melts by the empirical equation: log(Cu 2+ /Cu + ) = 0.25(ΔFMQ + 8.58 − 25050/T + 940P/T – 0.02P) − 4.73 + 5400/T + 1.99Λ + (280P – 90P2) where T is temperature in K, P is pressure in GPa and is the optical basicity of the composition. The effects of fO 2 , melt composition, temperature and pressure on Cu + /ΣCu indicate that Cu + will be the dominant oxidation state in terrestrial silicate melts (e.g., Cu + /ΣCu = 99% in an andesitic melt at 900 °C, 1 GPa and ΔFMQ = 1). The electron exchange reaction Cu 2+ + Fe 2+ → Cu + + Fe 3+ occurs on cooling and, given the abundance of Fe in natural melts, the oxidation state of Cu in natural glasses is unlikely to correspond to that in the original melt.

Copper↗
DOE OSTI2021

Melt extruded versus extrusion compression molded glass-polypropylene long fiber thermoplastic composites

Long fiber thermoplastic (LFT) composites are processed either with extrusion compression or fiber injection processes. The properties of LFT materials are highly influenced by processing techniques, which lead to different porosity contents, fiber length distributions, and fiber orientation distributions. It is important to understand the various LFT processing techniques and their effects on mechanical, thermal, and microscopic properties. This work considered LFT sheets processed via extrusion, which offers highly aligned fibers (referred to as “Tecnogor composites”), and LFT composites produced via extrusion compression molding (ECM), which offers a random distribution of fibers. Tecnogor composites exhibited higher flexural strength (35–65%), flexural modulus (132–172%), tensile strength (39–52%), tensile modulus (67–75%), and Izod impact resistance (195–220%) than the random LFT composites. This response was attributed to the aligned fibers in Tecnogor composites. Mathematical models including Halpin-Tsai and Lavengood-Goettler were used to predict and compare the Young’s modulus of Tecnogor and ECM composites, respectively.

mechanical testing↗
DOE OSTI2022

Redesigned Hybrid Nylons with Optical Clarity and Chemical Recyclability

Aliphatic polyamides, or nylons, are typically highly crystalline and thermally robust polymers used in high-performance applications. Nylon 6, a high-ceiling-temperature (HCT) polyamide from e-caprolactam, lacks expedient chemical recyclability, while low-ceiling temperature (LCT) nylon 4 from pyrrolidone exhibits complete chemical recyclability, but it is thermally unstable and not melt-processable. Here, we introduce a hybrid nylon, nylon 4/6, based on a bicyclic lactam composed of both HCT ..epsilon..-caprolactam and LCT pyrrolidone motifs in a hybridized offspring structure. Hybrid nylon 4/6 overcomes trade-offs in (de)polymerizability and performance properties of the parent nylons, exhibiting both excellent polymerization and facile depolymerization characteristics. This stereoregular polyamide forms nanocrystalline domains, allowing optical clarity and high thermal stability, however, without displaying a melting transition before decomposition. Of a series of statistical copolymers comprising nylon 4/6 and nylon 4, a 50/50 copolymer achieves the greatest synergy in both reactivity and polymer properties of each homopolymer, offering an amorphous nylon with favorable properties, including optical clarity, a high glass transition temperature, melt processability, and full chemical recyclability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Synthesis of metallic glass nanoparticles by inert gas condensation

Inert Gas Condensation (IGC) is a versatile method for the synthesis of ultrafine nanoparticles. While it has been mostly used in the synthesis of nanocrystalline particles it has also been employed in the synthesis of metallic glass nanoparticles, which can be further used in the generation of nanostructured metallic glasses, known as nanoglasses. In this work, we use molecular dynamics simulations to investigate the IGC processes leading to the synthesis of Cu 64 Zr 36 amorphous nanoparticles. We investigate the growth of nanoparticles up to 7.3 nm diameter using long simulations of up to 130 ns, under relatively low pressures in the range of 4 to 10 bars. Results indicate a significant effect of pressure on the final structure of the amorphous nanoparticles, yet no clear influence on the segregation of Cu atoms to its surface. Cu segregation occurring at all pressures results in a thin Cu rich layer, about 2.5 Å thick, that coats all nanoparticles. Here, statistics of atomic Voronoi polyhedra shows that the fraction of full icosahedra in the nanoparticles produced at 4 bars is equivalent to that of bulk metallic glasses produced by melt and quench at 10 9 K/s. Higher pressures result in a lower fraction of full icosahedra.

36 MATERIALS SCIENCE↗