Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “generative diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Wetting Behavior of Calcium Ferrite Slags on Cristobalite Substrates

Calcium ferrite (CF) is a significant intermediate adhesive phase in high-basicity sinters. The wettability between calcium ferrite (CF) and gangue plays an important role in the assimilation process. The wettability of CF-based slags, in which a constant amount (2 mass pct.) of Al{sub 2}O{sub 3}, MgO, SiO{sub 2}, and TiO{sub 2} was added, on solid SiO{sub 2} (cristobalite) substrates at 1523 K (1250 °C) was investigated. The interfacial microstructure and spreading mechanisms were discussed for each sample. All the tested slag samples exhibited good wettability on the SiO{sub 2} substrate. The initial apparent contact angles were in the range of 20 to 50 deg, while the final apparent contact angles were ~ 5 deg. The wetting process could be divided into three stages on the basis of the change in diameter, namely the “linear spreading” stage, “spreading rate reduction” stage, and “wetting equilibrium” stage. It was found that the CF-SiO{sub 2} wetting system exhibits dissolutive wetting and the dissolution of SiO{sub 2} into slag influences its spreading process. The spreading rate increases with a decrease in the ratio of viscosity to interfacial tension, which is a result of the addition of Al{sub 2}O{sub 3}, MgO, SiO{sub 2}, and TiO{sub 2}. After cooling, a deep corrosion pit was formed in the substrate and a diffusion layer was generated in front of the residual slag zone; further, some SiO{sub 2} and Fe{sub 2}O{sub 3} solid solutions precipitated in the slag.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A diffusion-limited reaction model for self-propagating Al/Pt multilayers with quench limits

A diffusion-limited reaction model was calibrated for Al/Pt multilayers ignited on oxidized silicon, sapphire, and tungsten substrates, as well as for some Al/Pt multilayers ignited as free-standing foils. The model was implemented in a finite element analysis code and used to match experimental burn front velocity data collected from several years of testing at Sandia National Laboratories. Moreover, both the simulations and experiments reveal well-defined quench limits in the total Al + Pt layer (i.e., bilayer) thickness. At these limits, the heat generated from atomic diffusion is insufficient to support a self-propagating wave front on top of the substrates. Quench limits for reactive multilayers are seldom reported and are found to depend on the thermal properties of the individual layers. Here, the diffusion-limited reaction model is generalized to allow for temperature- and composition-dependent material properties, phase change, and anisotropic thermal conductivity. Utilizing this increase in model fidelity, excellent overall agreement is shown between the simulations and experimental results with a single calibrated parameter set. However, the burn front velocities of Al/Pt multilayers ignited on tungsten substrates are over-predicted. Finally, possible sources of error are discussed and a higher activation energy (from 41.9 kJ/mol.at. to 47.5 kJ/mol.at.) is shown to bring the simulations into agreement with the velocity data observed on tungsten substrates. Finally, this higher activation energy suggests an inhibited diffusion mechanism present at lower heating rates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

A generative artificial intelligence framework based on a molecular diffusion model for the design of metal-organic frameworks for carbon capture

Metal-organic frameworks (MOFs) exhibit great promise for CO 2 capture. However, finding the best performing materials poses computational and experimental grand challenges in view of the vast chemical space of potential building blocks. Here, we introduce GHP-MOFassemble, a generative artificial intelligence (AI), high performance framework for the rational and accelerated design of MOFs with high CO 2 adsorption capacity and synthesizable linkers. GHP-MOFassemble generates novel linkers, assembled with one of three pre-selected metal nodes (Cu paddlewheel, Zn paddlewheel, Zn tetramer) into MOFs in a primitive cubic topology. GHP-MOFassemble screens and validates AI-generated MOFs for uniqueness, synthesizability, structural validity, uses molecular dynamics simulations to study their stability and chemical consistency, and crystal graph neural networks and Grand Canonical Monte Carlo simulations to quantify their CO 2 adsorption capacities. We present the top six AI-generated MOFs with CO 2 capacities greater than 2m mol g -1 , i.e., higher than 96.9% of structures in the hypothetical MOF dataset.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Virtual Volumetric Additive Manufacturing (VirtualVAM)

Abstract Tomographic volumetric additive manufacturing (VAM) produces arbitrary 3D geometries by exposure of a rotating volume of photopolymer resin to tomographically‐patterned illumination. This enables high speed, layer‐less printing of parts from a wide range of photopolymers not amenable to layer‐by‐layer processes. Since the entire geometry is produced at once over the course of a few seconds to minutes, molecular diffusion length scales become significant to the printing process. Understanding these molecular reaction and diffusion processes is imperative for advancing VAM to a usable technology. These processes are experimentally very difficult to monitor and measure. Herein, VirtualVAM ‐ a simulation framework for modeling the tomographic VAM process, is developed and experimentally validated. VirtualVAM simulates reaction, diffusion, and heat generation processes over the course of a print with single‐voxel resolution. From a few experimentally‐determined input parameters and a set of images for projection, VirtualVAM is able to generate a large spatio‐temporal data set for any given tomographic VAM print. Using VirtualVAM, a number of experimentally‐unattainable aspects of the VAM process are investigated such as single‐voxel conversion profiles, effect of molecular oxygen, and stopping time determination. VirtualVAM also enables the optimization of exposure patterns to further improve contrast between in‐part and out‐of‐part delivered dose.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

THE SCALING RELATIONS AND THE FUNDAMENTAL PLANE FOR RADIO HALOS AND RELICS OF GALAXY CLUSTERS

Diffuse radio emission in galaxy clusters is known to be related to cluster mass and cluster dynamical state. We collect the observed fluxes of radio halos, relics, and mini-halos for a sample of galaxy clusters from the literature, and calculate their radio powers. We then obtain the values of cluster mass or mass proxies from previous observations, and also obtain the various dynamical parameters of these galaxy clusters from optical and X-ray data. The radio powers of relics, halos, and mini-halos are correlated with the cluster masses or mass proxies, as found by previous authors, while the correlations concerning giant radio halos are in general the strongest. We found that the inclusion of dynamical parameters as the third dimension can significantly reduce the data scatter for the scaling relations, especially for radio halos. We therefore conclude that the substructures in X-ray images of galaxy clusters and the irregular distributions of optical brightness of member galaxies can be used to quantitatively characterize the shock waves and turbulence in the intracluster medium responsible for re-accelerating particles to generate the observed diffuse radio emission. The power of radio halos and relics is correlated with cluster mass proxies and dynamical parameters in the form of a fundamental plane.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

MESOSCALE THERMAL TRANSPORT MEASUREMENTS OF MULTI-PHASE AND POROUS NUCLEAR FUELS USING A SQUARE-WAVE PULSE THERMOREFLECTANCE TECHNIQUE

The safe and efficient operation of nuclear reactors require accurate knowledge of peak temperatures in the fuel assemblies. The temperature profiles are governed by the thermal transport properties of the fuel, namely the thermal conductivities (k) and thermal diffusivities (D). These values can be very difficult to measure as they are known to vary considerably from the measured bulk values of the fresh fuel, and quickly degrade with increasing burnup [1 -3] . Laser-based techniques have been effectively used for non-destructive and non-contact thermal transport measurements of a wide variety of materials, including nuclear materials [4-6] that would otherwise prove too hazardous or difficult to measure otherwise. In this study, a new thermoreflectance technique known as square-pulse transient thermoreflectance (SPTR) is described and used to determine the mesoscale thermal diffusivity of both uranium sesquisilicide (U3Si2) and uranium nitride (UN) phases in a composite fuel with micron level spatial resolution [7]. This technique employs a rapid train of square-wave pulses from an excitation laser to create a periodic heat flux on a gold coated sample surface. Surface adsorption results in transient film temperatures and hence rapid fluctuations in thermoreflectance that can be measured via a detection laser coupled with a digital oscilloscope. The lasers are coaxially focused on the sample surface, allowing for a sample measurement area of a single convolved laser spot size (~2 µm). A sensitivity analysis was conducted to identify key measurement parameters of this technique using reference materials with a range of thermal conductivities comparable to those of both ceramic, composite, and metal nuclear fuel types (1.4 – 27.2 W/m-K). The reference materials were measured using the new technique as well as a spatial-domain thermoreflectance technique (SDTR) previously reported for a comparison [8]. Additionally, measurements of several U3Si2 and UN phase regions of a polished UN/U3Si2 (70/30 vol.%) sample were taken, and the resulting calculated D values are reported, with both techniques showing excellent agreement between samples. This technique was used to scan a multiphase region at 5 micron increments to generate a local diffusivity map, demonstrating the utility of the techniques for measuring thermal transport properties in specimens with precipitates and secondary phases. Furthermore, the technique is currently being applied to measure thermal properties of Fast Flux Test Reactor (FFTR) irradiated metal fuel specimens whose porous microstructure make it very difficult to measure using other techniques. Comparison of the local scale measurements are compared with the pre-irradiated fuel samples to show the degradation of thermal transport in fuels due to pores from fission gas bubbles and other irradiation induced defects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

Coupling of Independent Electrochemical Reactions and Fluorescence at Closed Bipolar Interdigitated Electrode Arrays

Electrochemical reactions occurring at the opposite ends of bipolar electrodes (BPEs) are necessarily coupled, enabling electron transfer events at one end to be read out optically, for example, by coupling to fluorogenic reactions at the other end. In order to explore the potential of this technique for studying multiple redox events, arrays of parallel BPE interdigitated electrode arrays (IDEAs) were fabricated and integrated with separate analytical and reporter microfluidic channels, respectively, in a closed BPE configuration. The apparatus was initially evaluated employing Fe(CN) 6 3/4- in the analytical channel coupled to weakly emissive resazurin and strongly emissive resorufin as the fluorogenic redox reporter pair. We then used the device to investigate a proton-coupled electron transfer reaction, hydroquinone (QH 2 ) oxidation, in structures with an integrated pH modulation electrode (PME). A pH-sensitive dye, fluorescein, was co-introduced into the analytical channel to monitor PME modulation of solution pH, and its coupling to QH 2 oxidation, thereby permitting changes in solution pH, and consequently QH 2 oxidation rate, to be monitored directly in the analytical channel and compared to the fluorescence in the reporter channel. Additionally, diffusion of OH - generated at the PME produced a spatial pH profile that was visualized via fluorescein emission, and, because the oxidation of QH 2 at each BPE is strongly dependent on the local pH, via the coupled fluorogenic reaction at the opposite pole of the corresponding BPE digit in the reporter channel. Thus, BPE IDEAs support the coupling of independent redox reactions and the use of fluorescence imaging to explore a diverse set of spatially varying electrochemical phenomena realized in a variety of electrochemical geometries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Enhanced Light Absorption in Fluorinated Ternary Small-Molecule Photovoltaics

Using small-molecule donor (SMD) semiconductors in organic photovoltaics (OPVs) has historically afforded lower power conversion efficiencies (PCEs) than their polymeric counterparts. The PCE difference is attributed to shorter conjugated backbones, resulting in reduced intermolecular interactions. Here, a new pair of SMDs is synthesized based on the diketopyrrolopyrrole-benzodithiophene-diketopyrrolopyrrole (BDT-DPP2) skeleton but having fluorinated and fluorinefree aromatic side-chain substituents. Ternary OPVs having varied ratios of the two SMDs with PC61BM as the acceptor exhibit tunable open-circuit voltages (Vocs) between 0.833 and 0.944 V due to a fluorination-induced shift in energy levels and the electronic “alloy” formed from the miscibility of the two SMDs. A 15% increase in PCE is observed at the optimal ternary SMD ratio, with the short-circuit current density (Jsc) significantly increased to 9.18 mA/cm2. The origin of Jsc enhancement is analyzed via charge generation, transport, and diffuse reflectance measurements, and is attributed to increased optical absorption arising from a maximum in film crystallinity at this SMD ratio, observed by grazing incidence wide-angle X-ray scattering.

14 SOLAR ENERGY↗
DOE OSTI2020

Hybrid nanocapsules for in situ TEM imaging of gas evolution reactions in confined liquids

Liquid cell transmission electron microscopy (TEM) enables the direct observation of dynamic physical and chemical processes in liquids at the nanoscale. Quantitative investigations into reactions with fast kinetics and/or multiple reagents will benefit from further advances in liquid cell design that facilitate rapid in situ mixing and precise control over reagent volumes and concentrations. This work reports the development of inorganic–organic nanocapsules for high-resolution TEM imaging of nanoscale reactions in liquids with well-defined zeptoliter volumes. These hybrid nanocapsules, with 48 nm average diameter, consist of a thin layer of gold coating a lipid vesicle. As a model reaction, the nucleation, growth, and diffusion of nanobubbles generated by the radiolysis of water is investigated inside the nanocapsules. When the nanobubbles are sufficiently small (10–25 nm diameter), they are mobile in the nanocapsules, but their movement deviates from Brownian motion, which may result from geometric confinement by the nanocapsules. Gases and fluids can be transported between two nanocapsules when they fuse, demonstrating in situ mixing without using complex microfluidic schemes. The ability to synthesize nanocapsules with controlled sizes and to monitor dynamics simultaneously inside multiple nanocapsules provides opportunities to investigate nanoscale processes such as single nanoparticle synthesis in confined volumes and biological processes such as biomineralization and membrane dynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2014

The influence of vacancy generation at the initial stage of ion implantation

The paper presents a coupled isothermal model at the initial stage of a solid surface treatment with particle beams. Mechanical stresses arising due to the interaction of particles with the surface affect the redistribution of the implanted impurity. Vacancies in the metal surface and their generation under stress are also taken into account. The kinetic law is formulated on the basis of thermodynamics of irreversible processes. The authors used numerical investigation methods. As a result, they have obtained the distributions of impurity concentration and deformations for various time moments. The authors also compare the concentration and deformation profiles with and without vacancies and study the influences of some model parameters. The effect of vacancy generation on the diffusion has been established to lead to an increase in the depth of penetration, as well as in the concentration of impurities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Dynamics of metal-induced crystallization of ultrathin Ge films by rapid thermal annealing

Though Ge crystallization has been widely studied, few works investigate metal-induced crystallization of ultrathin Ge films. For 2 nm Ge films in oxide matrix, crystallization becomes challenging due to easy oxidation and low mobility of Ge atoms. Introducing metal atoms may alleviate these problems, but the functions and the behaviours of metal atoms need to be clarified. This paper investigates the crystallization dynamics of a multilayer structure 1.9 nm Ge/0.5 nm Al/1.5 nm Al{sub 2}O{sub 3} under rapid thermal annealing (RTA). The functions of metal atoms, like effective anti-oxidation, downshifting Raman peaks, and incapability to decrease crystallization temperature, are found and explained. The metal behaviours, such as inter-diffusion and defect generation, are supported with direct evidences, Al-Ge nanobicrystals, and Al cluster in Ge atoms. With these understandings, a two-step RTA process achieves high-quality 2 nm nanocrystal Ge films with Raman peak at 298 cm{sup −1} of FWHM 10.3 cm{sup −1} and atomic smooth interfaces.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2018

Particle-in-cell simulations of magnetically driven reconnection using laser-powered capacitor coils

In this study, we propose an experimental scheme to fulfill magnetically driven reconnections. Here, two laser beams are focused on a capacitor-coil target and then strong currents are wired in two parallel circular coils. Magnetic reconnection occurs between the two magnetic bubbles created by the currents in the two parallel circular coils. A two-dimensional particle-in-cell simulation model in the cylindrical coordinate is used to investigate such a process, and the simulations are performed in the ( r , z ) plane. The results show that with the increase of the currents in the two coils, the associated magnetic bubbles expand and a current sheet is formed between the two bubbles. Magnetic reconnection occurs when the current sheet is sufficiently thin. A quadrupole structure of the magnetic field in the θ direction ( B θ ) is generated in the diffusion region and a strong electron current along the r direction ( J e r ) is also formed due to the existence of the high-speed electron flow away from the X line in the center of the outflow region. Finally, because the X line is a circle along the θ direction, the convergence of the plasma flow around r = 0 will lead to the asymmetry of J e r and B θ between the two outflow regions of magnetic reconnection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Transport coefficients for magnetic-field evolution in inviscid magnetohydrodynamics

The magnetized resistivity and electrothermal tensors when substituted into the induction equation lead to electrothermal magnetic field generation, resistive magnetic diffusion, and magnetic field advection due to resistivity gradients, temperature gradients and currents. Here, the advection terms driven by temperature gradient and current have cross-field components (perpendicular to both the magnetic field and the driving term) that depend on significantly modified versions of Braginskii’s transport coefficients. The improved fits to Braginskii’s coefficients given by Epperlein and Haines and Ji and Held give physically incorrect results for cross-field advection at small Hall parameters (product of cyclotron frequency and collision time). The errors in Epperlein and Haines’ fits are particularly severe, giving increasing advection velocities below a Hall parameter of one when they should decrease linearly to zero. Epperlein and Haines’ fits can also give erroneous advection terms due to variations in effective atomic number. The only serious error in Braginskii’s fits is an overestimate in advection due to perpendicular resistivity. New fits for the cross-field advection terms are obtained from a direct numerical solution of the Fokker-Planck equation and Ji and Held’s higher order expansion approach that are continuous functions of the effective atomic number.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Counter-thermal flow of holes in high-mobility LaNiO 3 thin films

Measurements of electronic structure and theoretical models indicate that the Fermi surface of LaNiO 3 (LNO) is predominantly holelike, with a small electron pocket. However, measurements of the Hall and Seebeck effects yield nominally opposite signs for the dominant charge carrier type, making charge transport in LNO puzzling. Here, we combine measurements of the Hall, Seebeck, and Nernst coefficients in high-mobility epitaxial LNO thin films, and resolve this puzzle by demonstrating that the negative Seebeck coefficient is generated by the diffusion of holes from cold to hot regions of LNO. Here, we further examine this counter-thermal flow of holes by measuring the evolution of the Nernst coefficient from the diffusive to the ballistic regime, where the suppression of energy-dependent scattering leads to a reversal of the flow of holes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Temperature-Dependent Short-Circuit Capability of Silicon Carbide Power MOSFETs

Our paper presents a comprehensive short-circuit ruggedness evaluation and numerical investigation of up-to-date commercial silicon carbide (SiC) MOSFETs. The short-circuit capability of three types of commercial 1200-V SiC MOSFETs is tested under various conditions, with case temperatures from 25 to 200 degrees C and dc bus voltages from 400 to 750 V. It is found that the commercial SiC MOSFETs can withstand short-circuit current for only several microseconds with a dc bus voltage of 750 V and case temperature of 200 degrees C. Moreover, the experimental short-circuit behaviors are compared, and analyzed through numerical thermal dynamic simulation. Specifically, an electrothermal model is built to estimate the device internal temperature distribution, considering the temperature-dependent thermal properties of SiC material. Based on the temperature information, a leakage current model is derived to calculate the main leakage current components (i.e., thermal, diffusion, and avalanche generation currents). Finally, numerical results show that the short-circuit failure mechanisms of SiC MOSFETs can be thermal generation current induced thermal runaway or high-temperature-related gate oxide damage.

4H↗
DOE OSTI2020

Experiments and Simulations on the Turbulent, Rarefaction Wave Driven Rayleigh–Taylor Instability

Experiments were performed to observe the growth of the turbulent, Rayleigh–Taylor unstable mixing layer generated between air and SF 6 , with an Atwood number of A=(ρ 2 –ρ 1 )/(ρ 2 +ρ 1 ) = 0.64, where ρ 1 and ρ 2 are the densities of air and SF 6 , respectively. A nonconstant acceleration with an average value of 2300g 0 , where g 0 is the acceleration due to gravity, was generated by interaction of the interface between the two gases with a rarefaction wave. Three-dimensional, multimode perturbations were generated on the diffuse interface, with a diffusion layer thickness of δ = 3.6 mm, using a membraneless vertical oscillation technique, and 20 experiments were performed to establish a statistical ensemble. The average perturbation from this ensemble was extracted and used as input for a numerical simulation using the Lawrence Livermore National Laboratory (LLNL) Miranda code. Good qualitative agreement between the experiment and simulation was observed, while quantitative agreement was best at early to intermediate times. Several methods were used to extract the turbulent growth constant α from experiments and simulations while accounting for time varying acceleration. Experimental, average bubble and spike asymptotic self-similar growth rate values range from α = 0.022 to α = 0.032 depending on the method used, and accounting for variable acceleration. Values found from the simulations range from α = 0.024 to α = 0.041. Here, the values of α measured in the experiments are lower than what are typically measured in the literature but are more in line with those found in recent simulations.

42 ENGINEERING↗
DOE OSTI2016

Effect of a low-temperature-grown GaAs layer on InAs quantum-dot photoluminescence

The photoluminescence of InAs semiconductor quantum dots overgrown by GaAs in the low-temperature mode (LT-GaAs) using various spacer layers or without them is studied. Spacer layers are thin GaAs or AlAs layers grown at temperatures normal for molecular-beam epitaxy (MBE). Direct overgrowth leads to photoluminescence disappearance. When using a thin GaAs spacer layer, the photoluminescence from InAs quantum dots is partially recovered; however, its intensity appears lower by two orders of magnitude than in the reference sample in which the quantum-dot array is overgrown at normal temperature. The use of wider-gap AlAs as a spacer-layer material leads to the enhancement of photoluminescence from InAs quantum dots, but it is still more than ten times lower than that of reference-sample emission. A model taking into account carrier generation by light, diffusion and tunneling from quantum dots to the LT-GaAs layer is constructed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Helium bubble formation in aged plutonium metal at ambient conditions

A model of helium bubble formation is developed that assumes the initial nascent bubbles are generated when two diffusing helium atoms come within a distance of about the interatomic spacing of the plutonium atoms. These nascent bubbles are assumed to be locked in place and grow as additional helium atoms diffuse across their surfaces. Calculations of the helium-bubble number density and sizes as a function of age are compared to experiment. This leads to an inferred helium diffusion coefficient of-the-order of 10 -20 m 2 /s, supports the idea that most of the helium from alpha-decay end up in bubbles, and that previous transmission electron microscopy size estimates are biased low. The energy that helium can transfer to 40-year-old plutonium, upon expansion, is determined to be <0.1 Joules per gram of metal. The model predicts differences between the bubble properties in naturally and accelerated aged plutonium.

36 MATERIALS SCIENCE↗