Further research on instabilities in atmospheric flow systems associated with clear air turbulence
Fluid mechanics study of instabilities in atmospheric flow systems associated with clear air turbulence
Stoeffler, R. C.↗
SEARCH · Engineering Papers
Results for “flow instabilities”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Stability aspects of diverging subsonic flow
The paper describes the computation of two-dimensional, subsonic, diverging internal flows and how they differ from the corresponding converging flows. Such diverging or decelerating flows occur in such obvious places as subsonic diffusers and inlets; however, such flows also occur in supersonic nozzles in the presence of a normal shock. The flow instability and its relation to the numerical method used, boundary conditions, and viscous effects are assessed both analytically and numerically. The inviscid flow is shown to be physically unstable and a poor representation of the true viscous flow.
Cline, M. C.↗
On the instability of hypersonic flow past a flat plate
Qualitative features of the inviscid instability characteristics of hypersonic boundary-layer flows over a flat plate are considered. The instability of a viscous hypersonic boundary layer which exists far downstream from the leading edge of the plate. It is shown that the vorticity mode of instability operates on a different lengthscale from that obtained using a Chapman viscosity law. The growth rate predicted by a linear viscosity law is found to overestimate the size of the growth rate. The inviscid instability of the boundary layer near the leading edge interaction zone is discussed focusing on the strong-interaction zone which occurs sufficiently close to the leading edge. The vorticity mode in this regime is found to be unstable.
Blackaby, Nicholas D.↗
Mechanisms of Stationary Crossflow Instability Growth and Breakdown Induced by Forward-Facing Steps
An experimental study is performed to determine the mechanisms by which a forward-facing step impacts the growth and breakdown to turbulence of the stationary cross-flow instability. Particle image velocimetry measurements are obtained in the boundary layer of a 30◦swept flat plate with a pressure body. Step heights range from 53 % to 71 % of the boundary-layer thickness. The critical step height is approximately 60 % of the boundary-layer thickness for the current study, although it is also shown that the critical step height depends on the initial amplitude of the stationary cross-flow vortices. For the critical cases, the stationary cross-flow amplitude grows sharply downstream of the step, decays for a short region and then grows again. The initial growth region is linear, and can be explained primarily through the impact of the step on the mean flow. Namely, the step causes abrupt changes to the mean flow, resulting in large values of wall-normal shear, as well as highly inflectional profiles, due to either cross-flow reversal, separation or both. These inflectional profiles are highly unstable for the stationary cross-flow. Additionally,the reversed flow regions are significantly modulated by the stationary cross-flow vortices. The second region of growth occurs due to the stationary-cross-flow-induced modulation of the shear layer, which leads to multiple smaller wavelength stream wise vortices. High-frequency fluctuations indicate that the unsteady transition mechanism for the critical cases relates to the shedding of vortices downstream of reattachment of the modulated separated regions.
boundary layer stability↗
Flow Simulation of Solid Rocket Motors: Injection Induced Water-Flow Tests from Porous Media - 1
Prior to selecting a proper porous material for use in simulating the internal port flow of a solid rocket motor (SRM), in cold-flow testing, the flow emerging from porous materials is experimentally investigated. The injection-flow emerging from a porous matrix always exhibits a lumpy velocity profile that is spatially stable and affects the development of the longitudinal port flow. This flow instability, termed pseudoturbulence, is an inherent signature of the porous matrix and is found to generally increase with the wall porosity and with the injection flow rate. Visualization studies further show that the flow from porous walls made from shaving-type material (sintered stainless-steel) exhibits strong recirculation zones that are conspicuously absent in walls made from nodular or spherical material (sintered bronze). Detailed flow visualization observations and hot-film measurements are reported from tests of injection-flow and a coupled cross-flow from different porous wall materials. Based on the experimental data, discussion is provided on the choice of suitable material for SRM model testing while addressing the consequences and shortcomings from such a test.
Ramachandran, N.↗
Liquid neon heat transfer as applied to a 30 tesla cryomagnet
A 30-tesla magnet design is studied which calls for forced convection liquid neon heat transfer in small coolant channels. The design also requires suppressing boiling by subjecting the fluid to high pressures through use of magnet coils enclosed in a pressure vessel which is maintained at the critical pressure of liquid neon. This high pressure reduces the possibility of the system flow instabilities which may occur at low pressures. The forced convection heat transfer data presented were obtained by using a blowdown technique to force the fluid to flow vertically through a resistance heated, instrumented tube.
Papell, S. S.↗
Some unique experiments on receptivity
The objective of this study is to determine whether or not a solid trailing edge is required to produce efficient coupling between sound and instability waves in a shear layer. Instability waves in the shear layer of a subsonic jet, excited externally by a point sound source, were first visualized by using a phase-locked flow visualization technique. Various means were adopted to shield the sound reaching the nozzle lip. It was found that the low frequency sound couples more efficiently at distances downstream of the nozzle exit. To substantiate the findings further, a supersonic screeching jet was tested such that it passed through a small opening in a baffle placed parellel to the exit plane. The measured feedback or screech frequencies, and also the excited flow disturbances, were found to change drastically on traversing the baffle axially. Similar conclusions were reached when a second baffle was placed downstream of the first baffle, and the effects of moving the first baffle on the feedback frequency of sound generated by flow impingement on the second baffle were examined. It is argued that sound waves passing through the mixing layer of a jet can excite flow instability without the benefit of assistance and coupling at the trailing edge.
Ahuja, K. K.↗
Non-parallel effects in the instability of Long's vortex
Asymptotic results obtained by Foster and Smith (1989) for inviscid instability modes of the Type-II Long's vortex is extended to account for the effects of finite Reynolds number. It is shown that the nonparallelism of the flow is more important than the viscous terms in determining the finite-Re behavior due to the radial velocity scales with Re exp -1 M. A critical layer of the three-layer structrue of the parallel-flow instability modes is considerably modified by radial velocity. It is found that for azimuthal wavenumber n greater than 1, the nonparallelism stabilizes the unstable inertial modes, leading to determination of neutral curves. For n less than -1, the nonparallel effects always destabilize the vortex to these helical modes.
Foster, M. R.↗
Models of thermal/chemical boundary layer convection: Potential application to Venus
The upper boundary layer of Venus is comprised of at least two distinct chemical components, mantle and crust. Fluid dynamical models of convection within Venus' mantle were primarily of the thermal boundary layer type. Models assessing the ability of convective mantle flows to deform the crust were undertaken, but models exploring the effects of a variable thickness crust on mantle convection were largely lacking. A Venusian crust of variable thickness could couple back into, and alter, the mantle flow patterns that helped create it, leading to deformation mechanisms not predicted by purely thermal boundary layer convection models. This possibility is explored through a finite element model of thermal/chemical boundary layer convection. Model results suggest that a crust of variable thickness can serve as a mantle flow driver by perturbing lateral temperature gradients in the upper mantle. Resulting mantle flow is driven by the combination of free convective and nonuniform crustal distribution. This combination can lead to a flow instability manifest in the occurrence of episodic mantle lithosphere subduction initiated at the periphery of a crustal plateau. The ability of a light, near surface, chemical layer to potentially alter mantle flow patterns suggest that mantle convection and the creation and/or deformation of such a chemical layer may be highly nonseparable problems on time scales of 10(exp 8) years.
Lenardic, A.↗
Reverse-Tangent Injection in a Centrifugal Compressor
Injection of working fluid into a centrifugal compressor in the reverse tangent direction has been invented as a way of preventing flow instabilities (stall and surge) or restoring stability when stall or surge has already commenced. The invention applies, in particular, to a centrifugal compressor, the diffuser of which contains vanes that divide the flow into channels oriented partly radially and partly tangentially. In reverse-tangent injection, a stream or jet of the working fluid (the fluid that is compressed) is injected into the vaneless annular region between the blades of the impeller and the vanes of the diffuser. As used here, "reverse" signifies that the injected flow opposes (and thereby reduces) the tangential component of the velocity of the impeller discharge. At the same time, the injected jet acts to increase the radial component of the velocity of the impeller discharge.
Skoch, Gary J.↗
Thermal hydraulic analysis of the AFIP-7 irradiation test in the Advanced test Reactor – Model correlation and performance evaluation
We report as a system level code, RELAP5 is widely used in the nuclear field for the reactor hydraulic analysis. In the component/experimental level, it is frequently employed as well. This paper demonstrates that the RELAP5 flow simulation of the AFIP-7 irradiation experiment which has a complicated 3D geometry/flow path deviates by ~28% from the flow evaluation through a computational fluid dynamics (CFD) simulation, which has been validated against a flow test performed at Oregon State University. Thermal safety compliance analysis of an experiment planned to be irradiated in the Advanced Test Reactor is usually performed using the finite element analysis code, Abaqus. This research reveals the disadvantages of the Abaqus simulation in the flow instability and departure from nucleate boiling evaluations via a conjugate heat transfer analysis of the AFIP-7 irradiation experiment. As a result, a detailed CFD simulation is suggested for irradiation experiments with complicated flow paths, rather than a simplified RELAP5 simulation or hand calculations. The validated simulation approach will be integrated with the Boehmite correlations to investigate the oxide growth prediction on the fuel cladding in Part II of this research.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Modeling the effects of active wake mixing on wake behavior through large-scale coherent structures
The use of active wake mixing (AWM) to mitigate downstream turbine wakes has created new opportunities for reducing power losses in wind farms. However, many current analytical or semi-empirical wake models do not capture the flow instabilities that are excited through the blade pitch actuation. In this work, we develop a framework, which accounts for the impacts of the large-scale coherent structures and turbulence on the mean flow, for modeling AWM. The framework uses a triple-decomposition approach for the unsteady flow field and models the mean flow and fine-scale turbulence with a parabolized Reynolds-averaged Navier–Stokes (RANS) system. The wave components are modeled using a simplified spatial linear stability formulation that captures the growth and evolution of the coherent structures. Comparisons with high-fidelity large eddy simulations (LESs) of the turbine wakes showed that this framework was able to capture the additional wake mixing and faster wake recovery in the far-wake regions for both the pulse and helix AWM strategies with minimal computational expense. In the near-wake region, some differences are observed in both the RANS velocity profiles and initial growth of the large-scale structures, which may be due to some simplifying assumptions used in the model.
17 WIND ENERGY↗
Trailing edge noise
Shadowgraphic observations of the flow structure of a wall jet downstream of the trailing edge of a flat plate were carried out. Shadowgraphs obtained at jet exit Mach number 0.3 to 0.8 consistently showed an orderly large oscillatory flow structure. It is believed that these large scale disturbances are the result of flow instabilities. It is also believed that these orderly disturbances are responsible for generating the dominant part of trailing edge noise either directly or indirectly. The interaction of sound generated by these coherent oscillatory flow disturbances and the plate was investigated theoretically. It is found that the farfield noise directivity is strongly influenced by diffraction of sound at the leading edge of the plate.
Tam, C. K. W.↗
Numerical simulation of the edge tone phenomenon
Time accurate Navier-Stokes computations were performed to study a class 2 (acoustic) whistle, the edge tone, and to gain knowledge of the vortex-acoustic coupling mechanisms driving production of these tones. Results were obtained by solving the full Navier-Stokes equations for laminar compressible air flow of a two dimensional jet issuing from a slit interacting with a wedge. Cases considered were determined by varying the distance from the slit to the wedge. Flow speed was kept constant at 1,750 cm/s as was the slit thickness of 0.1 cm, corresponding to conditions in the experiments of Brown. The analytical computations revealed edge tones to be present in four harmonic stages of jet flow instability over the wedge as the jet length was varied from 0.3 to 1.6 cm. Excellent agreement was obtained in all four edge tone stage cases between the present computational results and the experimentally obtained frequencies and flow visualization results of Brown. Specific edge tone generation phenomena and further confirmation of certain theories and empirical formulas concerning these phenomena were brought to light in this analytical simulation of edge tones.
Dougherty, N. S.↗
Study of the development of natural instabilities in a laminar boundary layer in incompressible flow
Natural instabilities which are created in a laminar boundary layer and which consist of intermittent wave trains were studied. The spectral analysis of these fluctuations makes it possible to localize them in terms of frequency and to isolate their spectrum of amplitude modulation. The variation in terms of abscissa value and ordinate value of these instabilities is compared with the results derived from the solution of the Orr-Sommerfeld equation.
Burnel, S.↗
Extensional Flow of a Polystyrene Boger Fluid Through a 4:1:4 Axisymmetric Contraction/Expansion
The creeping flow of a dilute (0.025 wt%) monodisperse polystyrene/polystyrene Boger fluid through a 4:1:4 axisymmetric contraction/expansion is experimentally observed for a wide range of Deborah numbers. Pressure drop measurements across the orifice plate show a large extra pressure drop that increases monotonically with Deborah number above the value observed for a similar Newtonian fluid at the same flow rate. This enhancement in the dimensionless pressure drop is not associated with the onset of a flow instability, yet it is not predicted by existing steady-state or transient numerical computations with simple dumbbell models. It is conjectured that this extra pressure drop is the result of an additional dissipative contribution to the polymeric stress arising from a stress-conformation hysteresis in the strong non-homogeneous extensional flow near the contraction plane. Such a hysteresis has been independently measured and computed in recent studies of homogeneous transient uniaxial stretching of PS/PS Boger fluids. Flow visualization and velocity field measurements using digital particle image velocimetry (DPIV) show large upstream growth of the corner vortex with increasing Deborah number. At large Deborah numbers, the onset of an elastic instability is observed, first locally as small amplitude fluctuations in the pressure measurements, and then globally as an azimuthal precessing of the upstream corner vortex accompanied by periodic oscillations in the pressure drop across the orifice.
Rothstein, Jonathan P.↗
Measurement of Flow Pattern Within a Rotating Stall Cell in an Axial Compressor
Effective active control of rotating stall in axial compressors requires detailed understanding of flow instabilities associated with this compressor regime. Newly designed miniature high frequency response total and static pressure probes as well as commercial thermoanemometric probes are suitable tools for this task. However, during the rotating stall cycle the probes are subjected to flow direction changes that are far larger than the range of probe incidence acceptance, and therefore probe data without a proper correction would misrepresent unsteady variations of flow parameters. A methodology, based on ensemble averaging, is proposed to circumvent this problem. In this approach the ensemble averaged signals acquired for various probe setting angles are segmented, and only the sections for probe setting angles close to the actual flow angle are used for signal recombination. The methodology was verified by excellent agreement between velocity distributions obtained from pressure probe data, and data measured with thermoanemometric probes. Vector plots of unsteady flow behavior during the rotating stall regime indicate reversed flow within the rotating stall cell that spreads over to adjacent rotor blade channels. Results of this study confirmed that the NASA Low Speed Axial Compressor (LSAC) while in a rotating stall regime at rotor design speed exhibits one stall cell that rotates at a speed equal to 50.6 percent of the rotor shaft speed.
Lepicovsky, Jan↗
Perspectives on hypersonic viscous and nonequilibrium flow research
An attempt is made to reflect on current focuses in certain areas of hypersonic flow research by examining recent works and their issues. Aspects of viscous interaction, flow instability, and nonequilibrium aerothermodynamics pertaining to theoretical interest are focused upon. The field is a diverse one, and many exciting works may have either escaped the writer's notice or been abandoned for the sake of space. Students of hypersonic viscous flow must face the transition problems towards the two opposite ends of the Reynolds or Knudsen number range, which represents two regimes where unresolved fluid/gas dynamic problems abound. Central to the hypersonic flow studies is high-temperature physical gas dynamics; here, a number of issues on modelling the intermolecular potentials and inelastic collisions remain the obstacles to quantitative predictions. Research in combustion and scramjet propulsion will certainly be benefitted by advances in turbulent mixing and new computational fluid dynamics (CFD) strategies on multi-scaled complex reactions. Even for the sake of theoretical development, the lack of pertinent experimental data in the right energy and density ranges is believed to be among the major obstacles to progress in aerothermodynamic research for hypersonic flight. To enable laboratory simulation of nonequilibrium effects anticipated for transatmospheric flight, facilities capable of generating high enthalpy flow at density levels higher than in existing laboratories are needed (Hornung 1988). A new free-piston shock tunnel capable of realizing a test-section stagnation temperature of 10(exp 5) at Reynolds number 50 x 10(exp 6)/cm is being completed and preliminary tests has begun (H. Hornung et al. 1992). Another laboratory study worthy of note as well as theoretical support is the nonequilibrium flow experiment of iodine vapor which has low activation energies for vibrational excitation and dissociation, and can be studied in a laboratory with modest resources (Pham-Van-Diep et al. 1992).
Cheng, H. K.↗