SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Finite elastic slump of infinitely long, hollow incompressible cylinder bonded to rigid outer tube - failure prediction for metal and rubber
Reliability of Surveyor lunar roving vehicle design - mathematical models, failure modes, and predictions
Fast scan infrared detection and measuring instrument to predict failure of power transistors
Thin boundary problems of bimaterial plates bonded along circular arcs behaving like crack imperfections under bending, using fracture mechanics to predict failure
Computer program for statistical failure prediction on frequency-dependent circuits
Finite element analysis of critical stress distribution in canopy of deployed twin keel parawing, predicting failure stress levels
Axial compression tests were run on eleven thin-walled aluminum cylinders having rectangular cutouts. Various types of reinforcement were used around the cutouts, and some tests were run with no reinforcement. The test results are compared with the cylinder buckling loads prior to installation of the cutouts (obtained without damaging the cylinder by using a buckle-capture technique), and correlated with computer-predicted failure loads. The latter were based on the use of the STAGS computer program. For thin cylinders such as these, the test and computer-based analysis shows that for small to moderate size cutouts, reinforcement of the cutout is of no benefit unless the cylinder is of extremely high (geometrical) quality. For cylinder quality and cutout size where reinforcement is beneficial, the relative merits of the various reinforcement configurations are discussed, and an empirical basis for design is proposed.
The effects of gas pressure level, coolant temperature, and coolant flow rate on the stress-strain history and life of an air-cooled vane were analyzed using measured and calculated transient metal temperatures and a turbine blade stress analysis program. Predicted failure locations were compared to results from cyclic tests in a static cascade and engine. The results indicate that a high gas pressure was detrimental, a high coolant flow rate somewhat beneficial, and a low coolant temperature the most beneficial to vane life.
Results are presented for an experimental electron spin resonance study of chain-scission kinetics in oriented nylon fibers and in granular-filled elastomer composites. A reaction-rate molecular model is proposed as a tool to predict failure under various loadings. The model assumes a statistical distribution in stress on the polymeric chain structure. Interfacial failure in the filled composites is examined. Failure at the interface between the filler and the matrix may be largely adhesive or cohesive, depending on the magnitude of the interactive forces. It appears that the mechanical behavior of both single-component and filled composites depends on the composite nature of the structure. The electron spin resonance technique is shown to be suitable for experimental observation of phenomena directly related to atomic occurrences.
The purpose of the crash safety program is to support development of the technology to define and demonstrate new structural concepts for improved crash safety and occupant survivability in general aviation aircraft. The program involves three basic areas of research: full-scale crash simulation testing, nonlinear structural analyses necessary to predict failure modes and collapse mechanisms of the vehicle, and evaluation of energy absorption concepts for specific component design. Both analytical and experimental methods are being used to develop expertise in these areas. Analyses include both simplified procedures for estimating energy absorption capabilities and more complex computer programs for analysis of general airframe response. Full-scale tests of typical structures as well as tests on structural components are being used to verify the analyses and to demonstrate improved design concepts.
In-plane impulsive noise radiating from a hovering model rotor was measured in an anechoic environment. The hover acoustic signature was compared with existing theoretical prediction models with previous forward flight experiments using the same model rotor. These hover tests showed good experimental consistency with forward flight measurements, both in pressure level, and waveform character, over the range of Mach numbers tested (0.8 to 1.0). Generally poor correlation, however, was confirmed with current linear theory prediction efforts. Failure to predict both the peak pressure levels and the shape was reported, especially with increasing tip Mach number.
Some possible parameters which could be used to predict failures within packs of electrochemical cells based on measurements that are taken while the cells are cycling are discussed. Discharge and charge curves are presented and fitted to measure the efficiency of the cells in terms of voltage vs. time.
Silicone or parylene coatings protect circuits from damage by battery of military standard tests. PIND (Partical Impact Noise Detection) test proved unreliable in predicting failure for either coated or uncoated circuits.
Various aspects of the application of composite materials to aircraft structures are considered. Failure prediction techniques, buckling and postbuckling research, laminate fatigue analysis, damage tolerance, high temperature resin matrix composites and electrical hazards of carbon fiber composites are among the topics discussed.
A round-robin study was conducted which evaluated and compared different methods currently in practice for predicting crack growth in surface-cracked specimens. This report describes the prediction methods used by the Fracture Mechanics Engineering Section, at NASA-Langley Research Center, and presents a comparison between predicted crack growth and crack growth observed in laboratory experiments. For tests at higher stress levels, the correlation between predicted and experimentally determined crack growth was generally quite good. For tests at lower stress levels, the predicted number of cycles to reach a given crack length was consistently higher than the experimentally determined number of cycles. This consistent overestimation of the number of cycles could have resulted from a lack of definition of crack-growth data at low values of the stress intensity range. Generally, the predicted critical flaw sizes were smaller than the experimentally determined critical flaw sizes. This underestimation probably resulted from using plane-strain fracture toughness values to predict failure rather than the more appropriate values based on maximum load.
At the present time all traveling-wave maser and closed-cycle refrigerator system (TWM-CCR) and their power supply and helium compressor assemblies are operated manually. Many man-hours are required of highly trained and experienced operators, resulting in high operator cost. Of greater importance are the problems of unpredictable failure and long downtimes. Since field performance is not monitored, system degradation is detected only when it has progressed to the point of catastrophic failure. Without the aid of performance histories, failure diagnosis is arduous and slow. Rational and functional requirements for the TWM-CCR Automation project are the following: (1) to improve reliability and reduce downtime by providing unattended monitor and control, alarm and fault location, failure prediction and self-corrective action; (2) to reduce operator cost by providing automatic tuning and cooldown procedures; and (3) to improve system operations and development by providing the needed engineering data.
Predictive failure models for nickel cadmium batteries are discussed. Emphasis is given to the McDermott model, the Lander model, and the JPL failure model.
In spur gears both performance and failure predictions are known to be strongly dependent on the variation of load, lubricant film thickness, and total flash or contact temperature of the contacting point as it moves along the contact path. The need of an accurate tool for predicting these variables has prompted the development of a computer code based on recent findings in EHL and on finite element methods. The analyses and some typical results which to illustrate effects of gear geometry, velocity, load, lubricant viscosity, and surface convective heat transfer coefficient on the performance of spur gears are analyzed.