Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “extreme fast charging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

High-Efficiency, Medium-Voltage-Input, Solid-State-Transformer-Based 400-kW/1000V/400A Extreme Fast Charger for Electric Vehicles

Range anxiety and long battery charging time continue to be critical challenges to mass adaptation of EVs. A major identified gap to wider adoption of BEVs is the ability and availability to refuel quickly or to fast charge. Studies have shown that in areas where drivers have access to 50-kW or 120-kW fast charge stations, annual electric vehicle (EV) miles traveled (i.e., eVMT) increased by over 25%, even in cases where fast charging was used for 1% to 5% of total charging events. Charge stations of higher power not only alleviate the “range anxiety” and reduce the driver’s waiting time, but also requires less investment. Michigan Energy Office completed a study in early 2019 titled “Electric Vehicle Charger Placement Optimization in Michigan: Phase I – Highways”. This study finds a system with 150kW chargers, though more expensive individually, actually has lower total system cost when compared to a 50kW charging system when serving the same battery size EV. To be truly competitive to the ICEV refueling experience, even higher power stations are necessary. However, high power charge stations would create large power draws from the grid. If this occurs during peak demand periods, grid capacity could be overloaded. This problem needs to be addressed to reduce the impact on the electric utility infrastructure. The main goal of this project is to develop a 400-kW/400-A XFC system targeting total efficiency of 96.5 percent from the MVAC grid to a vehicle. The novel SST power cell topology, combined with a new silicon carbide (SiC) MOSFET device, enables a 3.5 percent improvement in system efficiency, a 50-percent smaller equipment footprint, and four times less weight than today’s DCFC systems. The SST technology would directly utilize MVAC at 4.8-kV or 13.2-kV. This would eliminate the line frequency transformer (LFT), which steps down medium-voltage AC to 3-Phase 480-V line-to-line voltage in current DCFC systems.

42 ENGINEERING↗
DOE OSTI2020

Rate-Dependent Aging Resulting from Fast Charging of Li-Ion Cells

The mass electrification of personal and service vehicles is reliant on the ability of battery packs to undergo extreme fast recharging. A central challenge is that the repeated exposure to high currents can trigger and/or accelerate mechanisms of performance degradation, such as lithium deposition, mechanical damage of active material particles, and impedance rise. Here, we investigate whether constraining high-rate charging to limited state-of-charge (SOC) ranges can mitigate these aging processes. Our experiments map the boundaries of lithium plating conditions, and also indicate that permanent losses of electrode capacity appear to be a function of cycle number, but not charging rate. Interestingly, we show that impedance rise appears to depend on charging rate alone, and not on the amount of charge passed at each cycle. This observation suggests that limiting fast charging to a narrow SOC range would only delay cell aging, but not fully prevent it from happening. We identify oxide-particle cracking as the likely mechanism for this impedance rise, suggesting that particle and electrode design are essential to enable fast charging. The findings of this work can inform the development of fast-charging protocols that are less damaging to cell health.

25 ENERGY STORAGE↗
DOE OSTI2021

Revealing the Fast and Durable Na + Insertion Reactions in a Layered Na 3 Fe 3 (PO 4 ) 4 Anode for Aqueous Na-Ion Batteries

Aqueous sodium-ion batteries represent a promising approach for stationary energy storage; however, the lack of appropriate anode materials has substantially retarded their development. Herein, we demonstrated an iron-based phosphate material of Na 3 Fe 3 (PO 4 ) 4 as an inexpensive and efficacious anode alternative. While the Fe 3+ /Fe 2+ redox couple renders a two-Na-insertion reaction with desirable potentials, its unique layered structure further facilitates the Na-insertion kinetics and reversibility. Consequently, this electrode exhibits an appealing Na-insertion performance, with a reversible capacity of ~83 mAh g –1 , suitable anode potential of -0.4 V vs Ag/AgCl, excellent rate capability of 200 C, and outstanding cycling of 6000 cycles. Utilizing operando synchrotron X-ray diffraction and X-ray absorption spectroscopy, we revealed the structural evolution of the Na 3 Fe 3 (PO 4 ) 4 anode during the two-electron reaction, where the extremely small volume expansion (~3%) enables its fast-charging and long-cycling capability. Our work suggests new considerations of developing versatile iron phosphate compounds as appealing anode materials for energy storage in aqueous electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2020

Fast Charge-Driven Li Plating on Anode and Structural Degradation of Cathode

Enabling fast charging in lithium ion batteries (LIBs) is a key factor to make electric vehicles drive just like gasoline-powered vehicles when the time comes to refuel. However, fast charging to current LIBs (LiNi x Mn y Co 1–z O 2 /graphite) is limited by lithium plating, which is barely reversible and causes LIBs to lose capacity over time. Thus, research to quantify the lithium plating in LIB cells is extremely important in improving our fundamental understanding of lithium plating behavior and enabling fast charging for LIBs. Here, we precisely quantified the amount of fast-charge-driven lithium plating in a coin-cell composed of LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532)/graphite. We found that the amount of lithium plating gradually increases with the cycle count and reaches 25.59 μmole (26.80 mAh g –1 cathode ) by the 100th cycle. The study also reveals that the NMC532 has lost 19% of its original lithium content after 100 fast-charging cycles; this, correspondingly, causes a lattice volumetric strain of 0.59%.

25 ENERGY STORAGE↗
DOE OSTI2021

Magnetohydrodynamic Control of Interfacial Degradation in Lithium-Ion Batteries for Fast Charging Applications

Interfacial anodic degradation in graphitic materials under fast charging conditions causes severe performance loss and safety hazard in lithium ion batteries. We present a novel method for minimizing the growth of these aging mechanism by application of an external magnetic field. Under magnetic field, paramagnetic lithium ions experience a magnetohydrodynamic force, which rotates the perpendicularly diffusing species and homogenizes the ionic transport. This phenomenon minimizes the overpotential hotspots at the anode/separator interface, consequently reducing SEI growth, lithium plating, and interfacial fracture. In situ electrochemical measurements indicate an improvement in capacity for lithium cobalt oxide/graphite pouch cell (20 mAh) charged from 1–5 C under an applied field of 1.8 kG, with a maximum capacity gain of 22% at 5C. Post-mortem FE-SEM and EDS mapping shows that samples charged with magnetic field have a reduced lithium deposition at 3C and a complete suppression of interfacial fracture at 5C. At 5C, a 24% reduction in the lithium content is observed by performing XPS on the anodic interfacial film. Finally, fast charging performance under variable magnetic field strengths indicate a saturation behavior in capacity at high fields (>2 kG), thereby limiting the field and consequent energy requirements to obtain maximum capacity gain under extreme conditions.

electromagnetism↗
DOE OSTI2022

A Fast‐Charging and High‐Temperature All‐Organic Rechargeable Potassium Battery

Abstract Developing fast‐charging, high‐temperature, and sustainable batteries is critical for the large‐scale deployment of energy storage devices in electric vehicles, grid‐scale electrical energy storage, and high temperature regions. Here, a transition metal‐free all‐organic rechargeable potassium battery (RPB) based on abundant and sustainable organic electrode materials (OEMs) and potassium resources for fast‐charging and high‐temperature applications is demonstrated. N‐doped graphene and a 2.8 m potassium hexafluorophosphate (KPF 6 ) in diethylene glycol dimethyl ether (DEGDME) electrolyte are employed to mitigate the dissolution of OEMs, enhance the electrode conductivity, accommodate large volume change, and form stable solid electrolyte interphase in the all‐organic RPB. At room temperature, the RPB delivers a high specific capacity of 188.1 mAh g −1 at 50 mA g −1 and superior cycle life of 6000 and 50000 cycles at 1 and 5 A g −1 , respectively, demonstrating an ultra‐stable and fast‐charging all‐organic battery. The impressive performance at room temperature is extended to high temperatures, where the high‐mass‐loading (6.5 mg cm −2 ) all‐organic RPB exhibits high‐rate capability up to 2 A g −1 and a long lifetime of 500 cycles at 70–100 °C, demonstrating a superb fast‐charging and high‐temperature battery. The cell configuration demonstrated in this work shows great promise for practical applications of sustainable batteries at extreme conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

π-Extended Ligands in Two-Coordinate Coinage Metal Complexes

Two-coordinate carbene-M I -amide (cMa, M I = Cu, Ag, Au) complexes have emerged as highly efficient luminescent materials for use in a variety of photonic applications, due to their extremely fast radiative rates via thermally activated delayed fluorescence (TADF) from an interligand charge transfer (ICT) process. A series of cMa derivatives were prepared to examine the variables which affect the radiative rate with the goal of understanding the parameters that control the radiative TADF process in these materials. We find that blue emissive complexes with high photoluminescence efficiency (Φ PL > 0.95) and fast radiative rates (k r = 4 x 10 6 s -1 ) can be achieved by selectively extending the π-system of the carbene and amide ligands. Of note is the role played by increasing the separation between the hole and electron in the ICT excited state. Analysis of temperature dependent luminescence data along with theoretical calculations indicate that the hole-electron separation alters the energy gap between the lowest energy singlet and triplet states (ΔE ST ) while keeping the radiative rate for the singlet state unchanged. As a result, this interpretation provides guidelines for the design of new cMa derivatives with even faster radiative rates as well as those with slower radiative rates and thus extended excited state lifetimes.

14 SOLAR ENERGY↗
DOE OSTI2022

Resolving Current-Dependent Regimes of Electroplating Mechanisms for Fast Charging Lithium Metal Anodes

Poor fast-charge capabilities limit the usage of rechargeable Li metal anodes. Understanding the connection between charging rate, electroplating mechanism, and Li morphology could enable fast-charging solutions. In this report we develop a combined electroanalytical and nanoscale characterization approach to resolve the current-dependent regimes of Li plating mechanisms and morphology. Measurement of Li + transport through the solid electrolyte interphase (SEI) shows that low currents induce plating at buried Li||SEI interfaces, but high currents initiate SEI-breakdown and plating at fresh Li||electrolyte interfaces. The latter pathway can induce uniform growth of {110}-faceted Li at extremely high currents, suggesting ion-transport limitations alone are insufficient to predict Li morphology. At battery relevant fast-charging rates, SEI-breakdown above a critical current density produces detrimental morphology and poor cyclability. Thus, prevention of both SEI-breakdown and slow ion-transport in the electrolyte is essential. This mechanistic insight can inform further electrolyte engineering and customization of fast-charging protocols for Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Kinetic pathways of fast lithium transport in solid electrolyte interphases with discrete inorganic components

The transport of lithium ions in the solid electrolyte interphase (SEI) has been previously accepted to proceed in two steps: a fast pore diffusion through the outer, porous organic layer followed by a slow knock-off or vacancy diffusion in the inner, dense inorganic layer. The second step is believed to be the rate-limiting step during fast-charging. In this study, we have intentionally constructed a thicker SEI (SEI-rich) structure on the surface of monoclinic Nb 2 O 5 (H-Nb 2 O 5 ) by adding LiNO 3 into a conventional ethylene carbonate based electrolyte. The electrochemical performance of two electrodes, one SEI-rich and one with few SEI (SEI-lean), was found to be almost the same, including their fast-charging capability and cycling stability, despite the significant difference in their SEI structure. Importantly, analysis using cryogenic scanning/transmission electron microscopy showed the discrete decoration of individual inorganic particles (e.g., Li 2 O) and amorphous species (LiN x O y /organic components) over the surface of H-Nb 2 O 5 . These discrete inorganic particles are in contradiction to the formation of dense inner inorganic layer, which has been commonly postulated. Based on these findings, we propose a new mechanism for Li ion transport through the SEI: one-step pore diffusion, without the second step slow diffusion. This one-step pore diffusion process provides an extremely fast Li ion transport, and effectively removes the kinetic limitation of Li ion transport in the SEI for fast charging. Finally, these results strongly suggest that the influence of SEI structure on the transport kinetics of lithium ions is much less significant than previously accepted. These results offer a new understanding of possible lithium ion transport pathway within SEI and may have implications for the future designs of fast-charging battery materials.

25 ENERGY STORAGE↗
DOE OSTI2020

Shield Design for 50 kW Three-Phase Wireless Charging System

In this paper, magnetic field emissions (MFE) from a 50 kW bipolar coil-based three-phase wireless charging system (WCS) is investigated. Then, a shield design is proposed to suppress the MFE below the safety limit identified by the International Commission of Non-Ionized Radiation Protection (ICNIRP) guidelines. Bipolar coil-based three-phase (3φ) WCSs provide extremely high power-density; therefore, the 3φ WCSs are highly promising for high-power fast-wireless-charging of the electric vehicles. For the high-power EV application, it is a critical challenge to design a shield to suppress the MFE below the safety limit. The traditional aluminum shield is found ineffective for the bipolar 3φ-WCS. The proposed shield is designed with high-permeability magnetic material, i.e. ferrite, nanocrystalline material, etc. The proposed shield is simulated in finite element analysis (FEA) and the FEA results show that the proposed magnetic shield effectively suppresses the magnetic field emission below the ICNIRP limit. The generalized design of the proposed shield can be used for even higher power bipolar coil based WCSs.

Mohammad, Mostak↗
NASA NTRS1975

Peak holding circuit for extremely narrow pulses

An improved pulse stretching circuit comprising: a high speed wide-band amplifier connected in a fast charge integrator configuration; a holding circuit including a capacitor connected in parallel with a discharging network which employs a resistor and an FET; and an output buffer amplifier. Input pulses of very short duration are applied to the integrator charging the capacitor to a value proportional to the input pulse amplitude. After a predetermined period of time, conventional circuitry generates a dump pulse which is applied to the gate of the FET making a low resistance path to ground which discharges the capacitor. When the dump pulse terminates, the circuit is ready to accept another pulse to be stretched. The very short input pulses are thus stretched in width so that they may be analyzed by conventional pulse height analyzers.

Oneill, R. W.↗
DOE OSTI2024

EV SALaD 2023 Demonstration: Best Practices and Mitigations for Protecting EVSE Infrastructure

The Electric Vehicle Secure Architecture Laboratory Demonstration (EV SALaD) program is a demonstration of cybersecurity best practices for high-power electric vehicle (EV) charging infrastructure led by Idaho National Laboratory (INL), in collaboration with other DOE National Laboratories participating in the EVs at Scale Consortium.a Sandia National Laboratories (SNL) and Pacific Northwest National Laboratory (PNNL) participated in the first 2-year (FY22-23) demonstration cycle for EV SALaD. This report documents the FY23 demonstration, the second in a series of demonstrations and collaborations in deploying and operating cybersecure EV charging infrastructure. It includes a summary of improvements from the FY22 demonstration, technical analysis of the FY23 demonstration, how the research demonstrates cyber-physical and cybersecurity best practices for high-power EV charging infrastructure, and related impacts to national and energy security. For EV SALaD, the FY22 demonstration focused on the detection, ranking, and prioritization of anomalous events for high-power EV charging. The FY23 demonstration additionally included the demonstration of cybersecurity best practices, which included protection and mitigation solutions to prevent, respond, and recover from anomalous events. During the demonstrations, the multi-lab EV SALaD team conducted a Test Effect Payload (TEP)b evaluation on extreme fast charger (XFC) hardware equipped with Cerberus, a detection and response solution, to demonstrate anomaly detection and mitigation cybersecurity best practices against cyber-enabled events.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Ligand-channel-enabled ultrafast Li-ion conduction

Li-ion batteries (LIBs) for electric vehicles and aviation demand high energy density, fast charging and a wide operating temperature range, which are virtually impossible because they require electrolytes to simultaneously have high ionic conductivity, low solvation energy and low melting point and form an anion-derived inorganic interphase. We report guidelines for designing such electrolytes by using small-sized solvents with low solvation energy. The tiny solvent in the secondary solvation sheath pulls out the Li + in the primary solvation sheath to form a fast ion-conduction ligand channel to enhance Li + transport, while the small-sized solvent with low solvation energy also allows the anion to enter the first Li + solvation shell to form an inorganic-rich interphase. The electrolyte-design concept is demonstrated by using fluoroacetonitrile (FAN) solvent. The electrolyte of 1.3 M lithium bis(fluorosulfonyl)imide (LiFSI) in FAN exhibits ultrahigh ionic conductivity of 40.3 mS cm -1 at 25 °C and 11.9 mS cm -1 even at -70 °C, thus enabling 4.5-V graphite||LiNi 0.8 Mn 0.1 Co 0.1 O 2 pouch cells (1.2 Ah, 2.85 mAh cm -2 ) to achieve high reversibility (0.62 Ah) when the cells are charged and discharged even at -65 °C. The electrolyte with small-sized solvents enables LIBs to simultaneously achieve high energy density, fast charging and a wide operating temperature range, which is unattainable for the current electrolyte design but is highly desired for extreme LIBs. This mechanism is generalizable and can be expanded to other metal-ion battery electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2022

Relativistic Alfvén Waves Entering Charge-starvation in the Magnetospheres of Neutron Stars

Instabilities in a neutron star can generate Alfvén waves in its magnetosphere. Propagation along the curved magnetic field lines strongly shears the wave, boosting its electric current j A . We derive an analytic expression for the evolution of the wavevector k and the growth of j A . In the strongly sheared regime, j A may exceed the maximum current j0 that can be supported by the background e ± plasma. We investigate these charge-starved waves, first using a simplified two-fluid analytic model, then with first-principles kinetic simulations. We find that the Alfvén wave is able to propagate successfully even when κ ≡ j A /j 0 $\ll$ 1. It sustains j A by compressing and advecting the plasma along the magnetic field lines with an increasing Lorentz factor, γ ≳ κ 1/2 . The simulations show how plasma instabilities lead to gradual dissipation of the wave energy. Our results suggest that an extremely high charge-starvation parameter κ ≳ 10 4 may be required in order for this mechanism to power the observed fast radio bursts (FRBs) from SGR 1935+2154. However, cosmological FRBs with much higher luminosities are unlikely to be a result of charge-starvation.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Electrolyte design for Li-ion batteries under extreme operating conditions

The ideal electrolyte for the widely used LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811)||graphite lithium-ion batteries is expected to have the capability of supporting higher voltages (≥4.5 volts), fast charging (≤15 minutes), charging/discharging over a wide temperature range (±60 degrees Celsius) without lithium plating, and non-flammability. No existing electrolyte simultaneously meets all these requirements and electrolyte design is hindered by the absence of an effective guiding principle that addresses the relationships between battery performance, solvation structure and solid-electrolyte-interphase chemistry. Here we report and validate an electrolyte design strategy based on a group of soft solvents that strikes a balance between weak Li+-solvent interactions, sufficient salt dissociation and desired electrochemistry to fulfil all the aforementioned requirements. Remarkably, the 4.5-volt NMC811||graphite coin cells with areal capacities of more than 2.5 milliampere hours per square centimetre retain 75 per cent (54 per cent) of their room-temperature capacity when these cells are charged and discharged at -50 degrees Celsius (-60 degrees Celsius) at a C rate of 0.1C, and the NMC811||graphite pouch cells with lean electrolyte (2.5 grams per ampere hour) achieve stable cycling with an average Coulombic efficiency of more than 99.9 per cent at -30 degrees Celsius. The comprehensive analysis further reveals an impedance matching between the NMC811 cathode and the graphite anode owing to the formation of similar lithium-fluoride-rich interphases, thus effectively avoiding lithium plating at low temperatures. Additionally, this electrolyte design principle can be extended to other alkali-metal-ion batteries operating under extreme conditions.

25 ENERGY STORAGE↗
DOE OSTI2020

Theoretical study on the massively augmented electro-osmotic water transport in polyelectrolyte brush functionalized nanoslits

In this paper, we demonstrate that functionalizing nanoslits with pH-responsive polyelectrolyte (PE) brushes can lead to extremely fast electroosmotic (EOS) water transport, where the maximum centreline velocity and the volume ow rate can be an order of magnitude larger than these quantities in identically charged brush-free nanochannels for a wide range of system parameters. Such an enhancement is most remarkable given that the brushes have been known to retard the transport by imparting additional drag on the fluid flow. We argue that this enhancement stems from the localization of the charge density of the brush-induced electric double layer (and hence the EOS body force) away from the nanochannel wall (or the location of the wall-induced drag force). This ensures a much larger impact of the EOS body force triggering such fast water transport. Lastly, the calculated flux values for the present brush-grafted nanochannels are found to be signi ficantly larger than those for a wide range of nanofluidic membranes and channels, suggesting that the brush functionalization can be considered as a mechanism for enabling such superfast nanofluidic transport.

42 ENGINEERING↗
DOE OSTI2025

Additive manufacturing of high explosives with inert dilution for wave shaping and detonation velocity grading

The performance of a high explosive charge is highly influenced by the detonation velocity and any inherent internal structure. Additively manufactured (AM) high explosive charges allow for a precisely engineered internal structure and the selective placement of discrete or graded volumes of a tailored material, which are unachievable by conventional means. The dilution of a solid explosive by an inert additive for detonation velocity reduction is herein evaluated for a method of material extrusion called a direct-ink-write AM, where an 1,3,5,7-tetranitro-1,3,5,7-tetrazoctane-based ultraviolet -curable energetic-binder paste explosive was diluted by the inert density mock 5-iodo-2′-deoxyuridine for use in the manufacture of multi-material explosive charges. The explosive ink was characterized for printing by rheological and particle size measurements, and the detonation velocities for 0–40 wt. % inert diluent were found to have a continuous linear reduction in detonation velocity down to 14.3% difference. A two-component 3D plane wave explosive lens with 8.038 km/s “fast” and 7.491 km/s “slow” diluted ink in an internal cone demonstrated a reduced time of breakout at the output face from 361 to 53 ns. A linearly graded “fast–slow–fast” cylinder was successfully printed and fired, showing engineered control along the length of the charge as the detonation velocity dropped from 7.851 to 6.700 km/s and then recovered to 7.241 km/s. The extreme control over the internal composition of a high explosive charge via a dual-material extruder/mixer challenges conventional manufacturing approaches and opens new avenues for engineered detonation wavefronts, high explosive charge performance, and new applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Comprehensive Strategy for Grid Forming Control in DC Coupled Photovoltaic and Battery Energy Storage Inverters

This paper presents an integrated DC-DC and DCAC grid-forming control strategy for DC-coupled photovoltaic (PV) plus battery energy storage systems, considering the effect of DC link voltage variations caused by direct PV connections. A power reference algorithm determines power distribution between the PV and battery to the grid while observing device power ratings to prevent the over-rating of components and keep the battery's state of charge within an acceptable range. The simulated utility-scale model in MATLAB/Simulink illustrates its ability against extreme phase angle variation contingencies in the grid while controlled through grid-forming control with a fast dynamic on DC link voltage. The simulation results confirm the effectiveness of the proposed control in integrating PV plus battery configurations with grid forming control and maintaining reliable grid operation under severe grid disturbances.

battery, boost, control, energy storage, grid form↗