Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dynamical correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Fluctuation statistics of outgoing longwave radiation in a general circulation model and in satellite data

Fluctuation statistics of Northern-Hemisphere-winter outgoing longwave radiation (OLR) obtained from data collected by Nimbus 7 and NOAA AVHRR are compared with those computed by a general circulation model (GCM). It was found that the GCM OLR has more variance than does the satellite, but that the GCM clear-sky OLR has less variance than the satellite OLR. The variance of the GCM outgoing full-sky OLR was found to be forced by clouds. While the standard deviation of the GCM full OLR is larger than that of the satellite OLR, the geographical patterns of both are similar. The autocorrelations of the modeled and the observed OLR also display similar geographical distributions, and they are in turn correlated with the dynamics.

Charlock, Thomas P.↗

Optimizing tuning masses for helicopter rotor blade vibration reduction including computed airloads and comparison with test data

The development and validation of an optimization procedure to systematically place tuning masses along a rotor blade span to minimize vibratory loads are described. The masses and their corresponding locations are the design variables that are manipulated to reduce the harmonics of hub shear for a four-bladed rotor system without adding a large mass penalty. The procedure incorporates a comprehensive helicopter analysis to calculate the airloads. Predicting changes in airloads due to changes in design variables is an important feature of this research. The procedure was applied to a one-sixth, Mach-scaled rotor blade model to place three masses and then again to place six masses. In both cases the added mass was able to achieve significant reductions in the hub shear. In addition, the procedure was applied to place a single mass of fixed value on a blade model to reduce the hub shear for three flight conditions. The analytical results were compared to experimental data from a wind tunnel test performed in the Langley Transonic Dynamics Tunnel. The correlation of the mass location was good and the trend of the mass location with respect to flight speed was predicted fairly well. However, it was noted that the analysis was not entirely successful at predicting the absolute magnitudes of the fixed system loads.

Pritchard, Jocelyn I.↗

Aeroelastic response and blade loads of a composite rotor in forward flight

The aeroelastic response, blade and hub loads, and shaft-fixed aeroelastic stability is investigated for a helicopter with elastically tailored composite rotor blades. A new finite element based structural analysis including nonclassical effects such as transverse shear, torsion related warping and inplane elasticity is integrated with the University of Maryland Advanced Rotorcraft Code. The structural dynamics analysis is correlated against both experimental data and detailed finite element results. Correlation of rotating natural frequencies of coupled composite box-beams is generally within 5-10 percent. The analysis is applied to a soft-inplane hingeless rotor helicopter in free flight propulsive trim. For example, lag mode damping can be increased 300 percent over a range of thrust conditions and forward speeds. The influence of unsteady aerodynamics on the blade response and vibratory hub loads is also investigated. The magnitude and phase of the flap response is substantially altered by the unsteady aerodynamic effects. Vibratory hub loads increase up to 30 percent due to unsteady aerodynamic effects.

Smith, Edward C.↗

Finite state aeroelastic model for use in rotor design optimization

In this article, a rotor aeroelastic model based on a newly developed finite state dynamic wake, coupled with blade finite element analysis, is described. The analysis is intended for application in rotor blade design optimization. A coupled simultaneous system of differential equations combining blade structural dynamics and aerodynamics is established in a formulation well-suited for design sensitivity computation. Each blade is assumed to be an elastic beam undergoing flap bending, lead-lag bending, elastic twist, and axial deflections. Aerodynamic loads are computed from unsteady blade element theory where the rotor three-dimensional unsteady wake is described by a generalized dynamic wake model. Correlation of results obtained from the analysis with flight test data is provided to assess model accuracy.

He, Chengjian↗

Rotating Shake Test and Modal Analysis of a Model Helicopter Rotor Blade

Rotating blade frequencies for a model generic helicopter rotor blade mounted on an articulated hub were experimentally determined. Testing was conducted using the Aeroelastic Rotor Experimental System (ARES) testbed in the Helicopter Hover Facility (HBF) at Langley Research Center. The measured data were compared to pretest analytical predictions of the rotating blade frequencies made using the MSC/NASTRAN finite-element computer code. The MSC/NASTRAN solution sequences used to analyze the model were modified to account for differential stiffening effects caused by the centrifugal force acting on the blade and rotating system dynamic effects. The correlation of the MSC/NASTRAN-derived frequencies with the experimental data is, in general, very good although discrepancies in the blade torsional frequency trends and magnitudes were observed. The procedures necessary to perform a rotating system modal analysis of a helicopter rotor blade with MSC/NASTRAN are outlined, and complete sample data deck listings are provided.

Wilkie, W. Keats↗

An Integrated Vehicle Modeling Environment

This paper describes an Integrated Vehicle Modeling Environment for estimating aircraft geometric, inertial, and aerodynamic characteristics, and for interfacing with a high fidelity, workstation based flight simulation architecture. The goals in developing this environment are to aid in the design of next generation intelligent fight control technologies, conduct research in advanced vehicle interface concepts for autonomous and semi-autonomous applications, and provide a value-added capability to the conceptual design and aircraft synthesis process. Results are presented for three aircraft by comparing estimates generated by the Integrated Vehicle Modeling Environment with known characteristics of each vehicle under consideration. The three aircraft are a modified F-15 with moveable canards attached to the airframe, a mid-sized, twin-engine commercial transport concept, and a small, single-engine, uninhabited aerial vehicle. Estimated physical properties and dynamic characteristics are correlated with those known for each aircraft over a large portion of the flight envelope of interest. These results represent the completion of a critical step toward meeting the stated goals for developing this modeling environment.

Totah, Joseph J.↗

Cascade Error Projection: An Efficient Hardware Learning Algorithm

A new learning algorithm termed cascade error projection (CEP) is presented. CEP is an adaption of a constructive architecture from cascade correlation and the dynamical stepsize of A/D conversion from the cascade back propagation algorithm.

learning algorithm pattern recognition cascade err↗

Failure Mechanisms and Life Prediction of Thermal and Environmental Barrier Coatings under Thermal Gradients

Ceramic thermal and environmental barrier coatings (TEBCs) will play an increasingly important role in gas turbine engines because of their ability to further raise engine temperatures. However, the issue of coating durability is of major concern under high-heat-flux conditions. In particular, the accelerated coating delamination crack growth under the engine high heat-flux conditions is not well understood. In this paper, a laser heat flux technique is used to investigate the coating delamination crack propagation under realistic temperature-stress gradients and thermal cyclic conditions. The coating delamination mechanisms are investigated under various thermal loading conditions, and are correlated with coating dynamic fatigue, sintering and interfacial adhesion test results. A coating life prediction framework may be realized by examining the crack initiation and propagation driving forces for coating failure under high-heat-flux test conditions.

Zju, Dongming↗

Performing a Large-Scale Modal Test on the B2 Stand Crane at NASA's Stennis Space Center

A modal test of NASA's Space Launch System (SLS) Core Stage is scheduled to occur at the Stennis Space Center B2 test stand. A derrick crane with a 150-ft long boom, located at the top of the stand, will be used to suspend the Core Stage in order to achieve defined boundary conditions. During this suspended modal test, it is expected that dynamic coupling will occur between the crane and the Core Stage. Therefore, a separate modal test was performed on the B2 crane itself, in order to evaluate the varying dynamic characteristics and correlate math models of the crane. Performing a modal test on such a massive structure was challenging and required creative test setup and procedures, including implementing both AC and DC accelerometers, and performing both classical hammer and operational modal analysis. This paper describes the logistics required to perform this large-scale test, as well as details of the test setup, the modal test methods used, and an overview and application of the results.

Stasiunas, Eric C.↗

Performing a Large-Scale Modal Test on the B2 Stand Crane at NASA's Stennis Space Center

A modal test of NASA’s Space Launch System (SLS) Core Stage is scheduled to occur prior to propulsion system verification testing at the Stennis Space Center B2 test stand. A derrick crane with a 180-ft long boom, located at the top of the stand, will be used to suspend the Core Stage in order to achieve defined boundary conditions. During this suspended modal test, it is expected that dynamic coupling will occur between the crane and the Core Stage. Therefore, a separate modal test was performed on the B2 crane itself, in order to evaluate the varying dynamic characteristics and correlate math models of the crane. Performing a modal test on such a massive structure was challenging and required creative test setup and procedures, including implementing both AC and DC accelerometers, and performing both classical hammer and operational modal analysis. This paper describes the logistics required to perform this large-scale test, as well as details of the test setup, the modal test methods used, and an overview of the results.

Stasiunas, Eric C.↗

NASA’s Orion Crew Module Seakeeping Simulation and Test Comparisons in Ocean Wave Environments

The NASA Orion Crew Module (CM) post-landing seakeeping and uprighting capabilities are being evaluated across a variety of ocean wave conditions. This paper provides an overview of quarter-scale and full-scale test data and how it compares with the CM seakeeping dynamic simulation results evaluated using Wave Energy Convertor Simulator (WEC-Sim).This includes a discussion of the status of the dynamic modeling effort, correlation of model inputs with the wave field from the test, and a comparison of the results against the physical test data with emphasis on the full-scale results. Analysis in the frequency domain showed similar response characteristics between the model and the test and shows energy peaks corresponding to both the natural response and the forced response due to the wave environment. Time domain comparisons showed that the linear WEC-Sim model under predicted the amplitude of the pitch and roll motion of the test article, with improved matching for smaller, longer crested waves. An attempt was made to correlate the pitch/roll response to incident wave slope to account for a possible delay in the BTA’s response. The results did not show a strong relationship in the response characteristics to incident wave slope, but better correlation was seen by comparing responses in the frequency domain. Evaluation of the simulation’s ability to match test results aided in understanding the current fidelity of the CM model in WEC-Sim and identifying areas for model improvement

Abigail Lockard↗

Interdecadal Variations in the Alaska Gyre

Climatic dynamic topography variations in the Alaska gyre during the period 1968-1990 are described with an objective analysis of more than 12000 STD and XBT stations, and COADS wind stress data Interannual the dynamic height and SST variations were correlated and were consistent with recently described large-scale climatic shifts in the North Pacific. The gyre was centered more to the east, circulation appeared stronger, and SST was lower during the early to mid-1970s than during the 1980s. The Aleutian low (NP and PNA indices) intensified during the interim, but the response did not appear as a gyre spinup. Instead, the associated wind stress anomalies forced a slowly varying dynamic height anomaly across the eastern and northern part of the gyre through Ekman convergence, which had the effect of displacing the gyre's low somewhat to the WSW in the 1980s. The wind curl spectrum was white, and the slow oceanic response was modeled as stochastic-forced climate variability with a simple first-order Markov autoregression process. Forcing was assumed to be Ekman pumping of the pycnocline, and the damping coefficient was estimated from the data to be approx. 1 yr. A hindcast with observed winds gave estimated dynamic height patterns similar to those observed, with a canonical correlation of 0.79 at 99% confidence. This response was weak in the western half of the gyre, where slow baroclinic variability may have been influenced by long Rossby wave propagation. A simple autoregression simulation using artificial white noise forcing shows the evolution of decadal variations similar in nature to those observed. This result, along with the low frequency correlation between dynamic height and SST, suggests that the upper-ocean climatic variability in this region is primarily wind forced.

Lagerloef, Gary S.E.↗

Case Study of Solar Wind and IMF Influence on Ionospheric Outflow

We examine ionospheric outflows in the high attitude magnetospheric polar cap during the POLAR satellite's apogee on 04/19/96 using the TIDE instrument. The pass has a fairly constant flux of H+ which is similar to many other passes, but there is a large amount of O+ present. The elevated levels of O+ may be due both to the geophysical conditions during the apogee pass (Kp=5) and prior to the pass. When the outflows for many high altitude polar cap passes are analyzed the O+ density correlates well with the dynamic pressure. There are several aspects of this pass which are interesting besides the abundance of O+ relative to H+. In this pass both the H+ and O+ outflow velocity correlate with both the solar wind speed and Interplanetary Magnetic Field (IMF) Bx. The geophysical conditions are such that the solar wind speed and IMF Bx are highly correlated with each other. For this case the dynamic pressure of the solar wind is fairly constant and has an average value of about 2.5 nPa which is typical for the solar wind, but the average solar wind speed is about 695 km/s which is greater than 450 km/s which is typical for the solar wind at I AU. The ion outflow measurements themselves are interrelated. The H+ density and parallel speed are anticorrelated which results in the constant flux. The 0+ density does not have as large of a anticorrelation with its parallel speed as H+ does with its parallel speed.

Elliott, H. A.↗

Application of Computational Fluid Dynamics (CFD) in transonic wind-tunnel/flight-test correlation

The capability for calculating transonic flows for realistic configurations and conditions is discussed. Various phenomena which were modeled are shown to have the same order of magnitude on the influence of predicted results. It is concluded that CFD can make the following contributions to the task of correlating wind tunnel and flight test data: some effects of geometry differences and aeroelastic distortion can be predicted; tunnel wall effects can be assessed and corrected for; and the effects of model support systems and free stream nonuniformities can be modeled.

Murman, E. M.↗

Ensemble Canonical Correlation Prediction of Seasonal Precipitation Over the United States: Raising the Bar for Dynamical Model Forecasts

This paper presents preliminary results of an ensemble canonical correlation (ECC) prediction scheme developed at the Climate and Radiation Branch, NASA/Goddard Space Flight Center for determining the potential predictability of regional precipitation, and for climate downscaling studies. The scheme is tested on seasonal hindcasts of anomalous precipitation over the continental United States using global sea surface temperature (SST) for 1951-2000. To maximize the forecast skill derived from SST, the world ocean is divided into non-overlapping sectors. The canonical SST modes for each sector are used as the predictor for the ensemble hindcasts. Results show that the ECC yields a substantial (10-25%) increase in prediction skills for all the regions of the US in every season compared to traditional CCA prediction schemes. For the boreal winter, the tropical Pacific contributes the largest potential predictability to precipitation in the southwestern and southeastern regions, while the North Pacific and the North Atlantic are responsible to the enhanced forecast skills in the Pacific Northwest, the northern Great Plains and Ohio Valley. Most importantly, the ECC increases skill for summertime precipitation prediction and substantially reduces the spring predictability barrier over all the regions of the US continent. Besides SST, the ECC is designed with the flexibility to include any number of predictor fields, such as soil moisture, snow cover and additional local observations. The enhanced ECC forecast skill provides a new benchmark for evaluating dynamical model forecasts.

Lau, William K. M.↗

Coupled rotor/fuselage dynamic analysis of the AH-1G helicopter and correlation with flight vibrations data

Under a research program designated Design Analysis Methods for VIBrationS (DAMVIBS), existing analytical methods are used for calculating coupled rotor-fuselage vibrations of the AH-1G helicopter for correlation with flight test data from an AH-1G Operational Load Survey (OLS) test program. The analytical representation of the fuselage structure is based on a NASTRAN finite element model (FEM), which has been developed, extensively documented, and correlated with ground vibration test. One procedure that was used for predicting coupled rotor-fuselage vibrations using the advanced Rotorcraft Flight Simulation Program C81 and NASTRAN is summarized. Detailed descriptions of the analytical formulation of rotor dynamics equations, fuselage dynamic equations, coupling between the rotor and fuselage, and solutions to the total system of equations in C81 are included. Analytical predictions of hub shears for main rotor harmonics 2p, 4p, and 6p generated by C81 are used in conjunction with 2p OLS measured control loads and a 2p lateral tail rotor gearbox force, representing downwash impingement on the vertical fin, to excite the NASTRAN model. NASTRAN is then used to correlate with measured OLS flight test vibrations. Blade load comparisons predicted by C81 showed good agreement. In general, the fuselage vibration correlations show good agreement between anslysis and test in vibration response through 15 to 20 Hz.

Corrigan, J. C.↗

Numerical simulation of a compressible homogeneous, turbulent shear flow

A direct, low Reynolds number, numerical simulation was performed on a homogeneous turbulent shear flow. The full compressible Navier-Stokes equations were used in a simulation on the ILLIAC IV computer with a 64,000 mesh. The flow fields generated by the code are used as an experimental data base, to examine the behavior of the Reynols stresses in this simple, compressible flow. The variation of the structure of the stresses and their dynamic equations as the character of the flow changed is emphasized. The structure of the tress tensor is more heavily dependent on the shear number and less on the fluctuating Mach number. The pressure-strain correlation tensor in the dynamic uations is directly calculated in this simulation. These correlations are decomposed into several parts, as contrasted with the traditional incompressible decomposition into two parts. The performance of existing models for the conventional terms is examined, and a model is proposed for the 'mean fluctuating' part.

Feiereisen, W. J.↗