Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drag estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1939

Interference of Tail Surfaces and Wing and Fuselage from Tests of 17 Combinations in the N.A.C.A. Variable-Density Tunnel

An investigation of the interference associated with tail surfaces added to wing-fuselage combinations was included in the interference program in progress in the NACA variable-density tunnel. The results indicate that, in aerodynamically clean combinations, the increment of the high-speed drag can be estimated from section characteristics within useful limits of accuracy. The interference appears mainly as effects on the downwash angle and as losses in the tail effectiveness and varies with the geometry of the combination. An interference burble, which markedly increases the glide-path angle and the stability in pitch before the actual stall, may be considered a means of obtaining satisfactory stalling characteristics for complete combination.

Sherman, Albert↗
NASA NTRS1952

On the design of airfoils in which the transition of the boundary layer is delayed

A method is presented for designing suitable thickness distributions and mean camber lines for airfoils permitting extensive chordwise laminar flow. Wind tunnel and flight tests confirming the existence of laminar flow; possible maintenance of laminar flow by area suction; and the effects of wind tunnel turbulence and surface roughness on the promotion of premature boundary layer transition are discussed. In addition, estimates of profile drag and scale effect on maximum lift of the derived airfoils are made.

BOUNDARY LAYER CONTROL - AIRFOILS↗
NASA NTRS1994

The deformation of flux tubes in the solar wind with applications to the structure of magnetic clouds and CMEs

Two dimensional magnetohydrodynamic simulations of the distortion of a magnetic flux tube, accelerated through ambient solar wind plasma, are presented. Vortices form on the trailing edge of the flux tube, and couple strongly to its interior. If the flux tube azimuthal field is weak, it deforms into an elongated banana-like shape after a few Alfven transit times. A significant azimuthal field component inhibits this distortion. In the case of magnetic clouds in the solar wind, it is suggested that the shape observed at 1 AU was determined by distortion of the cloud in the inner heliosphere. Distortion of the cloud beyond 1 AU takes many days. It is estimated that effective drag coefficients slightly greater than unity are appropriate for modeling flux tube propagation. Synthetic magnetic field profiles as would be seen by a spacecraft traversing the cloud are presented.

Cargill, Peter J.↗
NASA NTRS1995

Geometry of interplanetary magnetic clouds

Two dimensional magnetohydrodynamic simulations are presented of the distortion of a magnetic flux rope that is being accelerated through ambient solar wind plasma. The flux rope magnetic field has an axial component parallel to the solar wind field and an azimuthal component, which lies in the simulation plane. As the flux rope moves through the solar wind plasma, vortices form on its trailing edge and couple strongly to its interior. If the flux rope azimuthal field is weak, it deforms into an elongated banana-like shape a few Alfven transit times. A strong azimuthal field component tends to inhibit this distortion. If the flux rope is taken to model a magnetic cloud, it is suggested that the shape of the cloud at 1 AU is determined by its distortion in the inner solar wind. Distortion timescales beyond 1 AU are estimated as many days. It is estimated that effective drag coefficients somewhat greater than unity are appropriate for modelling flux rope propagation.

Cargill, P. J.↗
NASA NTRS1996

Ultralow Friction in a Superconducting Magnetic Bearing

Passive levitation by superconducting magnetic bearings can be utilized in flywheels for energy storage. Basic design criteria of such a bearing are high levitation force, sufficient vertical and horizontal stability and low friction. A test facility was built for the measurement and evaluation of friction in a superconducting magnetic bearing as a function of operating temperature and pressure in the vacuum vessel. The bearing consists of a commercial disk shaped magnet levitated above single grain, melt-textured YBCO high-temperature superconductor material. The superconductor was conduction cooled by an integrated AEG tactical cryocooler. The temperature could be varied from 50 K to 80 K. The pressure in the vacuum chamber was varied from 1 bar to 10(exp -5) mbar. At the lowest pressure setting, the drag torque shows a linear frequency dependence over the entire range investigated (0 less than f less than 40 Hz). Magnetic friction, the frequency independent contribution, is very low. The frequency dependent drag torque is generated by molecular friction from molecule-surface collisions and by eddy currents. Given the specific geometry of the set-up and gas pressure, the molecular drag torque can be estimated. At a speed of 40 Hz, the coefficient of friction (drag-to-lift ratio) was measured to be mu = 1.6 x 10(exp -7) at 10(exp -5) mbar and T = 60 K. This is equivalent to a drag torque of 7.6 x 10(exp -10) Nm. Magnetic friction causes approx. 1% of the total losses. Molecular friction accounts for about 13% of the frequency dependent drag torque, the remaining 87% being due to eddy currents and losses from rotor unbalance. The specific energy loss is only 0.3% per hour.

Bornemann, Hans J.↗
NASA NTRS1939

Interference of Tail Surfaces and Wing and Fuselage from Tests of 17 Combinations in the N.A.C.A. Variable-Density Tunnel

An investigation of the interference associated with tail surfaces added to wing-fuselage combinations was included in the interference program in progress in the NACA variable-density tunnel. The results indicate that, in aerodynamically clean combinations, the increment to the high-speed drag can be estimated from section characteristics within useful limits of accuracy. The interference appears mainly as effects on the downwash angel and as losses in the tail. An interference burble, which markedly increases the glide-path angle and the stability in pitch before the actual stall, may be considered a means of obtaining satisfactory stalling characteristics for a complete combination.

Sherman, Albert↗
NASA NTRS2011

Progress Toward Efficient Laminar Flow Analysis and Design

A multi-fidelity system of computer codes for the analysis and design of vehicles having extensive areas of laminar flow is under development at the NASA Langley Research Center. The overall approach consists of the loose coupling of a flow solver, a transition prediction method and a design module using shell scripts, along with interface modules to prepare the input for each method. This approach allows the user to select the flow solver and transition prediction module, as well as run mode for each code, based on the fidelity most compatible with the problem and available resources. The design module can be any method that designs to a specified target pressure distribution. In addition to the interface modules, two new components have been developed: 1) an efficient, empirical transition prediction module (MATTC) that provides n-factor growth distributions without requiring boundary layer information; and 2) an automated target pressure generation code (ATPG) that develops a target pressure distribution that meets a variety of flow and geometry constraints. The ATPG code also includes empirical estimates of several drag components to allow the optimization of the target pressure distribution. The current system has been developed for the design of subsonic and transonic airfoils and wings, but may be extendable to other speed ranges and components. Several analysis and design examples are included to demonstrate the current capabilities of the system.

Campbell, Richard L.↗
NASA NTRS1993

Aerodynamic optimization of an HSCT configuration using variable-complexity modeling

An approach to aerodynamic configuration optimization is presented for the high-speed civil transport (HSCT). A method to parameterize the wing shape, fuselage shape and nacelle placement is described. Variable-complexity design strategies are used to combine conceptual and preliminary-level design approaches, both to preserve interdisciplinary design influences and to reduce computational expense. Conceptual-design-level (approximate) methods are used to estimate aircraft weight, supersonic wave drag and drag due to lift, and landing angle of attack. The drag due to lift, wave drag and landing angle of attack are also evaluated using more detailed, preliminary-design-level techniques. New, approximate methods for estimating supersonic wave drag and drag due to lift are described. The methodology is applied to the minimization of the gross weight of an HSCT that flies at Mach 2.4 with a range of 5500 n.mi. Results are presented for wing planform shape optimization and for combined wing and fuselage optimization with nacelle placement. Case studies include both all-metal wings and advanced composite wings.

Hutchison, M. G.↗
NASA NTRS1946

Possibilities for drag reduction by boundary layer control

The mechanics of laminar boundary layer transition are reviewed. Drag possibilities for boundary layer control are analyzed using assumed conditions of transition Reynolds number, inlet loss, number of slots, blower efficiency, and duct losses. Although the results of such analysis are highly favorable, those obtained by experimental investigations yield conflicting results, showing only small gains, and sometimes losses. Reduction of this data indicates that there is a lower limit to the quantity of air which must be removed at the slot in order to stabilize the laminar flow. The removal of insufficient air permits transition to occur while the removal of excessive amounts of air results in high power costs, with a net drag increases. With the estimated value of flow coefficient and duct losses equal to half the dynamic pressure, drag reductions of 50% may be obtained; with twice this flow coefficient, the drag saving is reduced to 25%.

Naiman, I.↗
NASA NTRS1976

Applications of vortex lattice theory to preliminary aerodynamic design

Some applications of the vortex-lattice theory to the preliminary aerodynamic design and analysis of subsonic aircraft were presented. These methods include the Rockwell-Tulinius vortex-lattice theory for estimating aerodynamic characteristics, a Trefftz plane optimization procedure for determining the span loads for minimum induced drag, and a modification of the Trefftz plane procedure to estimate the induced drag for specified span loads. The first two methods are used to aerodynamically design aircraft planforms, twists, and cambers, and the latter method is used to estimate the drag for components such as flaps and control surfaces. Results from the theories for predicting lift and pitching moment, drag due to lift, and the drag of control surfaces are compared with experimental data. This data was obtained on a general aviation model with flaps and a close-coupled canard-wing model.

Paulson, J. W., Jr.↗
NASA NTRS1984

Turbulent roughness drag due to surface waviness at low roughness Reynolds numbers

The current investigation has the objective to provide data which will make it possible to obtain a better estimate regarding the roughness drag for surface waviness. The data employed for this investigation were acquired in connection with a wavy wall study which was conducted as part of an overall program to reduce the skin friction of turbulent boundary layers in external flows. The results of the present investigation show that the low-speed roughness drag of small-amplitude sinusoidal wave trains having wavelengths of the order of the boundary-layer thickness is not only a function of h/lambda (h = total wave height, lambda = wavelength), but, in addition, is also a function of the roughness Reynolds number.

Lin, J. C.↗
NASA NTRS1987

Shuttle derived atmosphere

The shuttle descends along a rather shallow path, thus providing some information on the horizontal structure of the atmosphere. Small scale structures were suggested (shears, potholes). The best estimates of the shuttle drag coefficient and projected areas are used to go from accelerometer data to density through the use of BET's (Best Estimated Trajectories). Data are from the IMU's (Inertial Measurement Unit) and the HiRAP (High Resolution Accelerometer Package).

Findlay, John↗
NASA NTRS1994

Measuring attitude with a gradiometer

This paper explores using a gravity gradiometer to measure the attitude of a satellite, given that the gravity field is accurately known. Since gradiometers actually measure a combination of the gradient and attitude rate and acceleration terms, the answer is far from obvious. The paper demonstrates that it can be done and at microradian accuracy. The technique employed is dynamic estimation, based on the momentum biased Euler equations. The satellite is assumed nominally planet pointed, and subject to control, gravity gradient, and partly radom drag torques. The attitude estimator is unusual. While the standard method of feeding back measurement residuals is used, the feedback gain matrix isn't derived from Kalman theory. instead, it's chosen to minimize a measure of the terminal covariance of the error in the estimate. This depends on the gain matrix and the power spectra of all the process and measurement noises. An integration is required over multiple solutions of Lyapunov equations.

Sonnabend, David↗
NASA NTRS2011

Effects of Low Activity Solar Cycle on Orbital Debris Lifetime

Long duration of low solar activity in the last solar minimum has an undesirable consequence of extending the lifetime of orbital debris. The AFRL TacSat-2 satellite decommissioned in 2008 has finally re-entered into the atmosphere on February 5th after more than one year overdue. Concerning its demise we have monitored its orbital decay and monthly forecasted Tacsat-2 re-entry since September 2010 by using the Orbital Element Prediction (OEP) model developed by the AFRL Orbital Drag Environment program. The model combines estimates of future solar activity with neutral density models, drag coefficient models, and an orbit propagator to predict satellite lifetime. We run the OEP model with solar indices forecast by the NASA Marshall Solar Activity Future Estimation model, and neutral density forecast by the MSIS-00 neutral density model. Based on the two line elements in 2010 up to mid September, we estimated at a 50% confidence level TacSat-2's re-entry time to be in early February 2011, which turned out to be in good agreement with Tacsat-2's actual re-entry date. The potential space weather effects of the coming low activity solar cycle on satellite lifetime and orbital debris population are examined. The NASA long-term orbital debris evolutionary model, LEGEND, is used to quantify the effects of solar flux on the orbital debris population in the 200-600 km altitude environment. The results are discussed for developing satellite orbital drag application product.

Cable, Samual B.↗
NASA NTRS1997

Neutral Orbital Altitude Density Effects on the International Space Station

One of the design requirements of the International Space Station (ISS) is that each year accelerations of one micro-g cannot be exceeded at the ISS internal payload location for 6 periods of not less than 30 consecutive days. Although there are other causes, this study deals only with the accelerations caused by atmospheric drag. The critical ambient neutral density, computed using the Marshall Engineering Thermosphere Model, required to produce accelerations of one micro-g on the ISS, is estimated using an atmospheric drag acceleration equation. Results show that the design requirements may be difficult to meet during periods of extremely high solar activity; the planned reboost and altitude strategies for the ISS may have to be revised to allow for the uncertainty in the prediction of neutral atmospheric density within the 100-day period established for orbital decay before reboost.

Smith, O.E.↗
NASA NTRS2019

Influence of Strain-Gage Balance Characteristics on the Precision Error of the Drag Coefficient

Improvements and results of a new method are presented that computes a pre-test estimate of the precision error of the drag coefficient of a wind tunnel model. The error estimate is defined as the part of the drag coefficient's precision error that is primarily associated with the precision error of the angle of attack measurement and physical characteristics of the chosen strain-gage balance. The method indirectly describes the precision error of the angle of attack measurement by using an assumed balance gage output variation of one microV/V. The physical characteristics of the balance, on the other hand, are described by partial derivatives of the axial and normal forces with respect to the strain-gage outputs. These derivatives can directly be obtained from the data reduction matrix of the balance. The precision error estimate itself is calculated by applying a simple explicit equation that uses the model reference area, the dynamic pressure, the angle of attack, the coefficients of the linear terms of the data reduction matrix, and the electrical output variation of one microvolt per volt as input. Precision errors at constant angle of attack may be visualized as contour plots by plotting them, for example, versus the Mach number and the total pressure. Characteristics of NASA's MC60E balance are used in combination with the reference area of a generic wind tunnel model in order to demonstrate that error estimates are independent of both the balance load format and the units chosen for the description of balance loads, model reference area, and the dynamic pressure. Finally, experimental data from a wind tunnel test of the Ames Check Standard Model in the NASA Ames 11-foot Transonic Wind Tunnel illustrates the application of the method to real-world test data.

precision error↗
NASA NTRS2010

Determining Atmospheric-Density Profile of Titan

A method was developed for measuring the atmospheric density of Titan, the largest moon of Saturn, to create an accurate density profile as a function of altitude. This will allow mission planners to select safe flyby altitudes, and for navigation engineers to accurately predict the delta-v associated with those flybys. The spacecraft angular rate vector profile as a function of time is collected via telemetry from the onboard attitude estimator once every 2 seconds. The telemetry for thruster times, as a function of time, for eight Reaction Control System (RCS) thrusters is gathered, once a second, from the Propulsion Manager algorithm of the Cassini onboard attitude-control flight software. Using these data, the ground software computes the angular momentum vector profile and the per-axis external torque as a function of time imparted from the spacecraft only due to the atmospheric drag. The software can then determine the Titan atmospheric density profile as a function of time and altitude with the known values of spacecraft center of mass, the Titan-relative range and velocity data, the projected area, and the aerocenter, along with the estimated drag coefficient in a free molecular flow field.

Sarani, Siamak↗