High rate CO2 valorization to organics via CO mediated silica nanoparticle enhanced fermentation
Not Available
Jack, Joshua↗
SEARCH · Engineering Papers
Results for “diffusion current”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The composition of gases from a diffusion flame above longleaf pine needle fuel beds
The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.
Biomass↗
Revisiting diffusion-based moisture functions: why do they fail?
Microbial activities in soil are controlled by the balance between physical and biological mechanisms that are currently implied by soil moisture-respiration relationships, but not explicitly represented. Diffusion based moisture functions focus on physical controls, while substrate kinetics based models primarily address biological drivers. How to harmonize these two types of models for robust predictions of soil respiration and other processes has not been addressed. Here we derived a generalizable analytical solution of diffusion-limited nonlinear microbial uptake kinetics, in which microbial metabolic rates were governed by both physical and biological drivers via substrate diffusion and microbial affinity. We proposed a soil trait concept to integrate both physical and biological perspectives into one unified function, and tested it using both laboratory and field based observations from a variety of soils. This approach provides a tractable and scalable approach that incorporates soil heterogeneity and functional complexity in macroscopic model descriptions.
59 BASIC BIOLOGICAL SCIENCES↗
Minor Product Polymerization Causes Failure of High-Current CO 2 -to-Ethylene Electrolyzers
Flooding of gas diffusion electrodes (GDEs) used in electrochemical conversion of CO 2 to ethylene is caused by polymerization of minor products. As such, the polymer so created reduces the hydrophobicity of the GDE, leading initially to a reduction in the ethylene yield and finally to complete failure.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
The MeerKAT Galaxy Cluster Legacy Survey I. Survey Overview and Highlights
MeerKAT’s large number (64) of 13.5 m diameter antennas, spanning 8 km with a densely packed 1 km core, create a powerful instrument for wide-area surveys, with high sensitivity over a wide range of angular scales. The MeerKAT Galaxy Cluster Legacy Survey (MGCLS) is a programme of long-track MeerKAT L-band (900–1670 MHz) observations of 115 galaxy clusters, observed for ~6–10 h each in full polarisation. The first legacy product data release (DR1), made available with this paper, includes the MeerKAT visibilities, basic image cubes at ~8" resolution, and enhanced spectral and polarisation image cubes at ~8" and 15" resolutions. Typical sensitivities for the full-resolution MGCLS image products range from ~3–5 μJy beam –1 . The basic cubes are full-field and span 2° × 2°. The enhanced products consist of the inner 1.2° × 1.2° field of view, corrected for the primary beam. The survey is fully sensitive to structures up to ~10' scales, and the wide bandwidth allows spectral and Faraday rotation mapping. Relatively narrow frequency channels (209 kHz) are also used to provide H I mapping in windows of 0 < z < 0.09 and 0.19 < z < 0.48. Here, in this paper, we provide an overview of the survey and the DR1 products, including caveats for usage. We present some initial results from the survey, both for their intrinsic scientific value and to highlight the capabilities for further exploration with these data. These include a primary-beam-corrected compact source catalogue of ~626 000 sources for the full survey and an optical and infrared cross-matched catalogue for compact sources in the primary-beam-corrected areas of Abell 209 and Abell S295. We examine dust unbiased star-formation rates as a function of cluster-centric radius in Abell 209, extending out to 3.5 R 200 . We find no dependence of the star-formation rate on distance from the cluster centre, and we observe a small excess of the radio-to-100 μm flux ratio towards the centre of Abell 209 that may reflect a ram pressure enhancement in the denser environment. We detect diffuse cluster radio emission in 62 of the surveyed systems and present a catalogue of the 99 diffuse cluster emission structures, of which 56 are new. These include mini-halos, halos, relics, and other diffuse structures for which no suitable characterisation currently exists. We highlight some of the radio galaxies that challenge current paradigms, such as trident-shaped structures, jets that remain well collimated far beyond their bending radius, and filamentary features linked to radio galaxies that likely illuminate magnetic flux tubes in the intracluster medium. We also present early results from the H I analysis of four clusters, which show a wide variety of H I mass distributions that reflect both sensitivity and intrinsic cluster effects, and the serendipitous discovery of a group in the foreground of Abell 3365.
79 ASTRONOMY AND ASTROPHYSICS↗
Floating Island International PHASE I FINAL TECHNICAL REPORT (Advancing the Development of Floating Solar-Powered Nanobubble Aeration Systems for Use with Floating Treatment Wetlands in Natural and Man-Made Waterbodies)
More and more freshwater lakes are suffering from algae blooms, which deprive water of oxygen and lead to widespread loss of aquatic life and production of dangerous toxins. When oxygen is lacking, methane is generated in the sediments as algae is decomposed; it has been calculated that more than half of global methane emissions come from nutrient-impaired freshwater systems (Beaulieu, 2021). Nutrients, mainly from agricultural run-off, feed algae blooms and are exacerbated by warming related to climate change. Artificial aeration is frequently used to restore oxygen to a waterbody. But diffuser aeration is inefficient and expensive, needs on-site grid power, and is failing to keep pace with the demands of water as it gets warmer with climate change. In the last five years, nanobubble aeration has been introduced into freshwater applications and shows promise for rapidly increasing dissolved oxygen effectively throughout the water column. Nanobubbles deliver oxygen in bubbles that have no buoyancy, so they stay in water longer and release their oxygen more fully, compared to large bubbles that rise and burst at the surface. The prospect of this new technology answering the deficiencies of diffuser aeration drove us to initiate the current project. During our Phase I period, we have successfully tested a nanobubble aeration system that can super-saturate oxygen levels. It is operated on solar power, and both the nanobubbler and solar array are mounted on a proprietary floating island platform, that also performs biological nutrient recycling. A rudimentary system was assembled and tested on a 6.5-acre research lake at our headquarters in Montana, where it was subjected to a summer drought that reduced water levels significantly, periods of severe cold in winter, and spring conditions that included heavy rainfall and violent thunderstorms. Our twice-weekly sampling throughout the project showed that dissolved oxygen levels rose rapidly and were maintained throughout winter and spring, well into June. The nanobubbler was able to run on solar power for long periods. Methane levels were tested periodically and found to decrease as oxygen increased. The nanobubbles appeared to have no adverse impact on fish or other aquatic life exposed to them. The stability of the installation survived the weather conditions. The many problems we encountered taught us what we need to improve in the next iteration. Towards the end of our Phase I, we were awarded a supplementary state grant that enabled us to acquire a new nanobubble system for testing that runs on DC, is extremely efficient and has few moving parts. We plan to team this with low-profile solar panels, lithium batteries and a controller that provides real-time data. The ultimate goal of this project is to commercialize an affordable and scalable lake management system that will oxygenate water from the surface down to the sludge. It will enliven fisheries, prevent toxic algae blooms and – most importantly for the fate of our planet - inhibit the production and release of methane from the sediments. We anticipate that as carbon credits expand to include methane, the cost of remediating waterbodies that produce methane will be offset. We firmly believe that this is a practical technology that works and will make a big difference when fully implemented.
14 SOLAR ENERGY↗
Analysis of cell-based diffusion acceleration for the slice balance approach
In this work, we perform analysis on the use of cell-based diffusion acceleration methodologies to accelerate the convergence of transport solutions discretized with the slice balance approach (SBA) on unstructured polygonal grids.We investigated both linear diffusion synthetic acceleration (DSA) and non linear diffusion acceleration (NDA), including its partial-current variant (pNDA). DSA and NDA were both shown to diverge for intermediate ranges of mesh optical thicknesses. However, pNDA and Krylov methods like GMRES and Broyden stabilized the acceleration schemes, including problems with degenerate cells formed by mesh refinement. (author)
42 ENGINEERING↗
DED Additively Manufactured HEAs Optimized via Parametric Study of Functionally Graded Materials
Complex concentrated alloys (CCAs) are a system of alloys composition of nearly equiatomic elements, creating a state of high configurational entropy in the material. These alloys are of interest for various industrial applications due to their high strength and hardness, wide operational temperature range, creep and diffusion resistance, and radiation resistance. In the current work CoCrFeNi-base CCAs are synthesize by combining three commonly industrial alloys: IN718, SS316L, and 70Co30Cr (commercially known as Stellite 21), in-situ utilizing directed energy deposition (DED) additive manufacturing (AM). One bulk specimen is fabricated with a 1:1:1 ratio of IN718, SS316L, and 70Co30Cr where IN718 is a source of nickel and chrome, SS316 is a source of iron and chrome, and 70Co30Cr is a source of cobalt and supplemental chrome. Additionally, a functionally graded material (FGM) of the identified CCA system from SS316 was fabricated with 10 layers, where the initial five layers are the base material of SS316L and graded by steps of 20% to transition to the CCA system. Overall build quality, microstructure, compositional distribution, phases analysis, and microhardness were studied by laser optical microscopy, scanning election microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD), and Vickers microhardness techniques. Overall build quality showed a successful bulk build with acceptable density, however unmelted particles are observed in the as-built alloy. Compositional results show that the system meets the Boltzmann’s hypothesis definition of an HEA, and that an FCC CCA was produced with increased hardness, small grain size, and superior hardness properties to the SS316L substrate. While initial XRD results show predominately FCC structure, EDS analysis of interdendritic regions show the existence of Laves phases in the material. The fabrication of an FGM CCA allowed for potential screening of additional alloy mixes which may be of interest to explore in future research, and the resulting composition is compared to predicted values. This novel method of CCA fabrication results in substantial cost savings of these CCA systems over traditional methods.
36 MATERIALS SCIENCE↗
Magnetic-Field Diffusion Effects in Beam Position Monitors III: Application to DARHT-II Beam Data
Beam position monitors (BPMs) provide time-resolved measurements of the current and centroid position of high-current electron beams in linear induction accelerators (LIAs). One of the types of detectors used in BPMs is the B-dot loop, which generates a signal from the EMF due to the time varying magnetic flux through the loop. If some of the boundaries of the loop are composed of thick metal walls with finite conductivity, the resulting signal must be corrected for the magnetic field diffusion into the metal. The theoretically predicted flux due to diffusion is in remarkable agreement with experimental measurements. Although accurate BPM measurements of beam current require correction of magnetic field diffusion, accurate measurement of beam position requires no correction. In this note, we present experimental validation of current and position results from a prototype detector employing finite conductivity sensing areas, based on experiments on the DARHT-II LIA.
43 PARTICLE ACCELERATORS↗
Elucidating the impact of the ionomer equivalent weight on a platinum group metal-free PEMFC cathode via oxygen limiting current
Leveraging the interactions between ionomer and catalyst can increase the performance of proton exchange membrane fuel cells. The impacts of the equivalent weight (EW) of perfluorosulfonic acid–based ionomers on the platinum group metal-free electrode structure and fuel cell performance have not been fully explored. Four membrane electrode assemblies (MEAs) were prepared by using a commercial Fe–N–C catalyst, two perfluorosulfonic acid ionomers with different EWs, that is, Aquivion 720 (A720) and Nafion 1100 (N1100), and two ionomer-to-catalyst (I/C) ratios. The four MEAs were characterized to understand the impact of the ionomer EW and content on the capacitance, proton conductivity, and mass transport on the cathode. The mass transport resistance was measured for the first time using a new oxygen reduction reaction limiting current method enabling to couple the effects of oxygen diffusion with liquid water generation. Low EW ionomer combined with a moderate I/C results in improved performance due to its enhanced proton conductivity. However, when used at high I/C, it can cause severe water flooding at high current density due to the enhanced liquid water uptake, especially at high relative humidity, resulting in lower catalyst utilization and higher mass transport resistance.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Diffusion of small anti-Schottky clusters in UO 2
The aggregation of irradiation-induced defect clusters in UO 2 leads to the formation of dislocation loops and cavities which contribute swelling and ultimately produce deleterious effects on the fuel. Despite their fundamental role in fuel evolution, the kinetics of these defect clusters are not currently well understood. In this work, we investigate the diffusive behavior of interstitial clusters via Molecular Dynamics (MD) simulations. In this work, our investigation considers a range of defect cluster sizes, each composed of N UO 2 units or anti-Schottky defects. We report a complex cluster size - mobility relation; increasing cluster size corresponds to an increase in mobility up until a critical size (N=4) where diffusivity reaches a maximum, after which the trend reverts and further increasing size corresponds to a decrease in mobility. The rapid migration observed correlates well with the very low barriers reported in a few historic experimental studies. Further analysis of the cluster shape and orientation reveals a strong structural preference for near-planar configurations oriented normal to the $\langle$100$\rangle$ direction. Rotational energy barriers are found to be similar in both magnitude and trend to the observed diffusion barriers. Lastly, connections are drawn to the behavior of large defect clusters including the formation of (1/3) $\langle$111$\rangle$ Frank dislocation loops.
36 MATERIALS SCIENCE↗
Experimental and computational study of the microporous layer and hydrophobic treatment in the gas diffusion layer of a proton exchange membrane fuel cell
Enabling fuel cell operation at high current density is critical for developing competitive alternative power system to replace internal combustion engine. However, liquid water management continues to be a challenge for high humidity or high current density operation. Water condensation in the porous media hinders efficient oxygen transport to the catalyst layer, which in turns, reduces fuel cell performance. To improve water management capability, the gas diffusion layer is often impregnated with Polytetrafluoroethylene (PTFE) and coated with a thin microporous layer, which have shown to improve fuel cell performance, especially under wet conditions. However, the fundamental mechanism that drives the performance enhancement is still not well understood. In this work, the effects of PTFE impregnation and MPL were studied using both experimental and computational techniques. Both limiting current and polarization tests under dry and wet operating condition are conducted to study the oxygen transport resistance and fuel cell performance. In addition, a 2-D, two-phase, multi-physics PEMFC model is developed to simulate performance and gain a fundamental understanding of local water saturation and oxygen concentration. The combined results show that 5 wt% PTFE impregnation with MPL significantly enhances liquid water management, which enables higher current density operation of a fuel cell.
25 ENERGY STORAGE↗
Chemical and structural evolutions of Li–Mn-rich layered electrodes at different current densities
Although the two active redox centers in Li-rich cathodes, including the anionic and cationic contributions, can enable Li-ion batteries to achieve outstanding specific energy, their behaviors at different current densities have not been clarified. In this report we provide a comparative study of transition metals (TMs) and oxygen redox activities by directly accessing their oxidation states in Li-rich materials operated at very different current rates. Our data reveal that the oxidation of oxygen in the near-surface region is at the same level for electrodes cycled with a wide range of current rates, indicating a reaction gradient of lattice oxygen redox reactions. The oxidation process of lattice oxygen is found to be dynamically compatible with that of the TMs. Combining the results of first principles calculations and complementary experimental findings, we propose a detailed mechanism of structural distortion from octahedral Li to tetrahedral Li and the role of oxygen vacancy in Li + diffusion. It is found that fast delithiation occurring at high current densities can easily cause local structural transformation, leading to a limited Li + diffusion rate and consequently suppressing rate capability.
25 ENERGY STORAGE↗
Recent Progress on Numerical Modeling for Microgravity Electric Field Flames: Preprint
This paper presents the recent progress on the NASA Physical Science Informatics (PSI) project PeleLM CFD of Ion Driven Winds from Diffusion Flames in simulating the E-FIELD Flames microgravity results. The focus of this project is to comprehensively simulate the behavior of a small diffusion flame under the influence of an externally applied electric field in zero-gravity. To date, the capability of accurately simulating electric field flames has eluded researchers because the system exhibits dramatic ranges of coupled temporal and spatial scales. Moreover, in earth gravity the hot combustion products are subject to buoyancy effects that are difficult to isolate from those generated by the electric field. This work is an implementation in an existing powerful simulation framework (PeleLM) for this problem using PeleLMeX in order to validate the model and investigate the complex coupled system. The current effort includes establishing the domain of a diffusion coflow burner, examining the boundary conditions, flame geometry and ignition with gravitational forces and also with an electric field applied. A detailed model is used that includes the chemistry of charged ions and chemiluminescent flame intermediates to capture any feedback between ion-driven convection and combustion behavior, and to allow quantitative comparisons with experimental measurements.
coflow flames↗
Proposed Material Properties, Allowable Stresses, and Design Curves of Diffusion Bonded Alloy 800H for the ASME Code Section III Division 5
Abstract Increased interest in compact heat exchangers (CHXs) to serve as intermediate heat exchangers of very high temperature reactors resulted in significant research and development on their design, analysis, and construction. Printed circuit heat exchangers are a type of CHXs with high thermal efficiency and compactness achieved through diffusion bonding a stack of etched plates with millimeter scaled channels. The diffusion bonding process changes the microstructural and mechanical properties of the wrought metal plates. The current nonnuclear design code ASME section VIII, division 1 captures the material property change through a “joint efficiency factor.” However, the current nuclear design code ASME section III, division 5 does not address or support the diffusion bonded material properties. Hence, there is a need to develop allowable stresses, isochronous curves, and fatigue life curves for various diffusion bonded alloys. In this study, Alloy 800H material was selected to establish the diffusion bonded material properties under tension, creep, fatigue, and creep-fatigue loads at elevated temperatures in the range 550–760 °C. A set of tests on diffusion bonded Alloy 800H (DB 800H) were performed and the acquired data are used in developing allowable stresses Sy, Su, Sr, Sm, St, Smt, So, isochronous curves and fatigue life curves according to the ASME section III, division 5 requirements. This paper also presents detailed procedures used in developing the ASME code section III division 5 design provisions for diffusion bonded Alloy 800H.
Engineering↗
Hexamethyldisiloxane pyrolysis: probing H-atom initiation by femtosecond two-photon LIF
Previous experiments have led to the hypothesis that pyrolysis of silica nanoparticle precursors carried in an inert central gas jet surrounded by a laminar flame is initiated not by thermal decomposition (the measured jet temperatures are too low for pyrolysis), but by reactions with H-atoms diffusing from the surrounding flame into the jet. The current work tests this hypothesis using femtosecond two-photon laser-induced fluorescence (fs-TPLIF) to image H-atom concentrations in the same flame configuration as the previous experiments. Methane flames (ϕ = 0.83, 1.01 and 1.13) were generated using a multi-element diffusion (Hencken) burner equipped with a central tube through which the N2 jet was introduced. The fs-TPLIF line imaging showed significant concentrations of H-atoms in the nitrogen jets at heights above the burner (HAB) close to the methane flame front. The measurements indicate radial diffusion of the H atoms from the flame to the jet is significant. The H-atom concentrations in the jet increased with increasing stoichiometry of the methane flame. Additional experiments were performed with hexamethyldisiloxane entrained in the central jet flow. In each case, a diffusion flame producing silica nanoparticles was established at the boundaries between the central jet and the methane flames. The 2D H-atom images showed a transition from over-ventilated diffusion flames to under-ventilated diffusion flames with increasing equivalence ratio. Furthermore, the fs-TPLIF profiles show a significant production of H-atoms within the jet when the surrounding flame is lean. This knowledge contributes to a deeper understanding of the underlying mechanisms governing these synthesis flame systems and opens avenues for advancing silica nanoparticle synthesis techniques.
Kim, Keunsoo↗
Theoretical and Experimental Study of Current from Non-Disintegrable Suspended Particles at a Rotating Disk Electrode
Understanding the current response at an electrode from suspended solid particles in an electrolyte is crucial for developing materials to be used in semi-solid electrodes for energy storage applications. Here, an analytical model is proposed to predict and understand the current response from non-disintegrable solid particles at a rotating disk electrode. The current is shown to be limited by a combination of ion diffusion within the solid particle and the mean residence time of the particle at the rotating disk electrode. This results in a relationship between current and angular frequency of I ∝ ω 3 / 4 , instead of the classical I ∝ ω 1 / 2 predicted by Levich theory. Specifically, the current response of Li 4 Ti 5 O 12 (LTO) microparticles suspended in a non-aqueous electrolyte of lithium hexafluorophosphate (LiPF 6 ) in ethylene carbonate: diethyl carbonate (EC:DEC) was determined experimentally and compared favorably with predictions from the proposed analytical model using fitting parameters consistent with the experimental conditions.
25 ENERGY STORAGE↗
Visualizing degradation mechanisms in a gas-fed CO 2 reduction cell via operando X-ray tomography
We utilize operando X-ray computed tomography, coupled with real-time electrochemical analysis, to reveal the underlying failure mechanisms of membrane electrode assemblies (MEAs) for electrochemical CO 2 reduction (eCO 2 R). Through operando imaging, we can obtain unprecedented insights into the dynamic behavior of the MEA under different operating conditions, revealing critical changes in interface interactions, phase distribution, and structural integrity over time. Our findings identify phenomena giving rise to the transition from CO 2 R to the hydrogen evolution reaction (HER), as evidenced by shifts in cathode potential and CO 2 R selectivity. The formation of inhomogeneous precipitates at the gas diffusion electrode disrupts the CO 2 supply and reduces the active sites for eCO 2 R, resulting in a shift toward H2 production during low current density operation. Additionally, under high current density conditions, rapid water crossover up to the microporous layer/gas diffusion layer promotes the transition from CO 2 R to HER, further shifting cell potential toward anodic direction. Oscillating voltage conditions reveal the dissolution and regrowth of precipitates, providing direct visualization of the competing selectivity of CO 2 R and HER. This work offers new insight into the degradation mechanisms of MEAs, with implications for the design of more durable CO 2 R systems.
Lee, Sol A [California Institute of Technology (Ca↗