SEARCH · Engineering Papers

Results for “depth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1964

Packing properties of fine powders and the depth of the lunar dust layer

Previous experimental and theoretical studies by Hapke and Van Horn [1963] and Hapke [1963] of surfaces which reflect light like the moon support the hypothesis that the lunar surface is covered with a layer of fine rock dust. The material in this layer appears to be in an extremely unconsolidated state, having a bulk density of the order of one-eighth that of solid rock. Such photometric studies can give information concerning only the upper few millimeters of the lunar soil. However, analyses of radiofrequency observations indicate that extensive areas of the moon may be covered to depths of the order of a meter or greater by a substance which is also much less dense than solid rock. From the radar reflectivity of the lunar surface at meter wavelengths Evans [1962] infers a dielectric constant of K = 2.7; Troitsky [1962] estimates K = 1.6 on the basis of radio-thermal observations at centimeter wavelengths. Since the RF dielectric constants of stony meteorites and of terrestrial rocks range from about 4 to 45 [Fensler et al., 1962] it is clear that the density of the lunar soil is unusually low at least to depths to which RF radiation can penetrate; Troitsky estimates this depth to be of the order of 20 wavelengths or greater in the 3-cm-wavelength range.

Powder↗

NASA NTRS1972

A study of the properties of beryllium doped silicon with particular emphasis on diffusion mechanisms: Profiles of depth dependent conductivity as determined by electrical surface probes

Very large diffusion coefficients were encountered and required the determination of impurity profiles for samples approximately 1 cm thick. Since conductivity values are readily converted into concentrations of electrically active impurities, the major problem became that of accurately determining the conductivity profiles of beryllium diffused silicon samples. Four-point probe measurements on samples having depth conductivities are interpreted in terms of conductivity profiles, based on an exact solution of the problem of exponentially depth dependent conductivity. Applications include surface conductivity determination where the form of the conductivity profile is known, and conductivity profile determination from probe measurements taken as the sample surface is progressively lapped away. The application is limited to samples having conductivity monotonically decreasing with depth from the probed surface.

Franks, R. K.↗

NASA NTRS1972

A depth profile of C-14 in the lunar rock 12002.

The procedure involved separating the rock sample into depth fractions, designated OPI-OP6, grinding and dissolving each sample in a teflon still. The results obtained for the C-14 depth profile are shown in a table. The value for OP4 is unusually high. This phenomenon can be explained by leakage of atmospheric C-14 during the test. The profile shows a definite decrease in C-14 activity with increasing depth in the rock.

Boeckl, R. S.↗

NASA NTRS1973

The depth distribution of hydrogen in lunar materials.

A technique employing the resonant nuclear reaction H-1(F-19, alpha gamma)O-16 has been used to measure hydrogen concentration versus depth in selected coarse fine fragments from the Apollo 11 and Apollo 15 missions, and in glass coated surface chips from two Apollo 15 rocks. The highly variable hydrogen content in the coarse fine fragments is concentrated mainly in a layer extending from the surface to a depth of 2000 plus or minus 500 A. The hydrogen content of the surface region of the Apollo 15 rock chips is comparable to that of the coarse fine samples, but is concentrated mainly within a few hundred angstroms of the surface. The hydrogen depth distribution in a piece of platinum foil from the Apollo 16 Lunar surface Cosmic Ray Experiment was also measured in an attempt to place a limit on the flux of 10- to 40-keV protons associated with a solar flare event.

Leich, D. A.↗

NASA NTRS1973

Radioactivities vs. depth in Apollo 16 and 17 soil

The radioactivities of Ar-37, Ar-39, and H-3 measured at a number of depths for Apollo 16 and 17 soil are reported. The Ar-37 activities vs depth in the Apollo 16 drill string increased with depth and reached a broad maximum in the neighborhood of 50 g per sq cm before decreasing. The Ar-39 activities in Apollo 17 soil were higher than in Apollo 16 soil, probably owing to the higher Fe and Ti contents. The H-3 activities in Apollo 16 and 17 soil were quite similar and indicate that the 4 August 1972 flare produced very little H-3 compared to the amount produced by solar flares during the previous 50 years.

Fireman, E. L.↗

NASA NTRS1974

Apollo drill core depth relationships

Preliminary depth relationships are presented for the Apollo 15, 16, and 17 drill core samples. For a given depth in any of these drill stems, the in situ lunar surface depth can be estimated. Ranges of uncertainty are also established, based on percent core recovery and degree of sample disturbance. The most likely explanation for the sample disturbance observed in the top three sections of the Apollo 16 drill stem is sample migration after the stem was capped on the lunar surface; essentially no sample was lost. Similar disturbance occurred in the Apollo 17 drill core, although to a lesser degree. The average original bulk densities (i.e., before any disturbance occurred) of the Apollo 15, 16, and 17 drill cores are 1.76, 1.59, and 1.87 g/cu cm, respectively. The Apollo 15 and 17 values are probably close to the in situ values; but the Apollo 16 average in situ density could be as much as 13% less than the already low density in the drill core.

Carrier, W. D., III↗

NASA NTRS1980

Spectral variation of optical depth at Tucson, Arizona between August 1975 and December 1977

A technique proposed by King and Byrne (1976) for inferring the daily value of the total ozone content of the atmosphere is applied to spectral optical depth measurements obtained at Tucson for a 29-month period between August 1975 and December 1977. The selection of wavelength regions appropriate for aerosol optical depth determinations in the visible and near infrared is discussed, and monthly averages of the total and aerosol optical depths are presented for five wavelengths between 0.4400 and 0.8817 microns. Finally, daily values of total ozone content are presented for the entire 133-day data set.

King, M. D.↗

NASA NTRS1981

A new method of Curie depth evaluation from magnetic data: Theory

An approach to estimating the Curie point isotherm uses the classical Gauss method inverting a system of nonlinear equations. The method, slightly modified by a differential correction technique, directly inverts filtered Magsat data to calculate the crustal structure above the Curie depth, which is modeled as a magnetized layer of varying thickness and susceptibility. Since the depth below the layer is assumed to be nonmagnetic, the bottom of the layer is interpreted as the Curie depth. The method, once fully developed, tested, and compared with previous work by others, is to be applied to a portion of the eastern U.S. when sufficient Magsat data are accumulated for the region.

Won, I. J.↗

NASA NTRS1981

Viscous relaxation of impact craters on icy planetary surfaces - Determination of viscosity variation with depth

Spacecraft images show that the icy Galilean satellites have surfaces with very low topographic relief. Impact craters on Ganymede and Callisto are anomalously shallow and are characterized by sharp well-defined rims and domed floors. These morphological characteristics can be explained by viscous relaxation of topography on an icy crust in which the viscosity is uniform or decreases with depth. Under these conditions, large craters relax more rapidly than small craters, therefore explaining a possible underabundance of large craters. Viscous relaxation on an icy crust that is thin compared to the crater diameter or on a thick icy crust in which viscosity increases with depth could not produce this crater morphology and would result in the more rapid relaxation of small craters rather than large craters. The results of this study suggest that more detailed analysis of relaxing impact crater morphology may resolve the rate of viscosity decrease with depth and so provide evidence on the interior thermal evolution of icy planetary bodies.

Parmentier, E. M.↗

NASA NTRS1984

Depth Gage for Threaded Holes

Tool for measuring threaded depth of tapped holes accurate and easy to use. Depth read from graduated scale on tool. Gives direct reading of depth, eliminating estimates and calculations. When tool is removed from hole, spring-loaded sleeve returns to zero.

Kahn, M. A.↗

NASA NTRS1982

Expected cycle life versus depth of discharge relationships of well behaved single cells and cell strings

The factors that might influence the cycle life vs. depth of discharge relationship are examined. This is done first at the single cell level using a progressively more complex cell life model. This is then extended to multicell battery strings where the stochastic aspects associated with groupings of cells are introduced. These relationships are important when considering the weight, cost, and life of battery packs. The results of this theoretical study are compared with a recent review of actual cell cycling data. The factors examined are the rate of capacity loss, the amount of excess capacity built into the cells, and the penalty in capacity loss resulting from the use of deep depths of discharge. This study suggests that the relationship between cycle life and depth of discharge is not one that can be varied of significantly improved by cell research. The relationship appears to be determined by certain more or less fixed cell parameters. Among multicell strings, the standard deviation, as expected, plays an important role in determining overall battery life.

Thaller, L. H.↗

NASA NTRS1983

A study on the spectral models for waves in finite water depth

From an extension of the Wallops Spectrum (Huang et al., 1981) for the deep water waves, spectral models for waves in finite water depths are developed. Stokes wave expansions are found to offer a good approximation for intermediate water depth. The spectral function in this case is controlled by three parameters: the significant slope, the nondimensional depth, and the peak frequency. It is pointed out that solitary and cnoidal wave models must be used for the shallow water waves. The controlling parameters now reduce to the Urell number and the peak frequency. Even though the resulting spectral models place special emphasis on the energy-containing range of the spectrum, they are not limited to this range and they are not limited to any particular sea state. They are seen as offering a possible explanation of the variations in the special slope observed by previous investigators.

Huang, N. E.↗

NASA NTRS1984

Depth of origin of solar active regions

Observations show that the individual bipolar magnetic regions on the sun remain confined during their decay phase, with much of the magnetic field pulling back under the surface, in reverse of the earlier emergence. This suggests that the magnetic field is held on a short rein by subsurface forces, for otherwise the region would decay entirely by dispersing across the face of the sun. With the simple assumption that the fields at the surface are controlled from well-defined anchor points at a depth h, it is possible to relate the length l of the bipolar region at the surface to the depth h, with h about equal to l. The observed dimensions l about equal to 100,000 km for normal active regions, and l about equal to 10,000 km for the ephemeral active regions, indicate comparable depths of origin. More detailed observational studies of the active regions may be expected to shed further light on the problem.

Parker, E. N.↗

NASA NTRS1984

Focal depths and fault plane solutions of earthquakes and active tectonics of the Himalaya

Synthetic seismograms were compared with long-period body waves for nine earthquakes with epicenters in the Himalayan arc to determine depths of foci and to improve fault plane solutions. Focal depths are shallow (10-20 km). Inferred slip vectors are locally perpendicular to the mountain range; they plunge very gently (about 10 deg) in the eastern sections of the range and more steeply (about 25 deg) in western sections. Assuming India to be a rigid plate, the radially oriented slip vectors imply that southern Tibet extends at about half the rate of underthrusting in the Himalaya and therefore probably at about 5-10 mm/yr. The shallow depths and gentle dips of the fault planes, at least for the events in the eastern half of the range, are consistent with coherent underthrusting of the Indian plate beneath, at least, the Lesser Himalaya. The steeper dips of fault planes in the western part of the arc might reflect deformation of the overriding thrust plate or simply a steepening of the main underthrusting zone beneath the Greater Himalaya.

Baranowski, J.↗

NASA NTRS1984

The distribution of earthquakes with depth and stress in subducting slabs

The global variation of Benioff zone seismicity with depth and the orientation of stress axes of deep and intermediate earthquakes is explained using numerical models of subducting slabs. Models that match the seismicity and stress require a barrier to flow at the 670 km seismic discontinuity. The barrier may be a viscosity increase of at least an order of magnitude or a chemical discontinuity. Instantaneous flow is subparallel to the slabs for models with a viscosity increase but contorted for models with a chemical barrier. Log N (number of earthquakes) decreases linearly to 250-300 km depth and increases thereafter. Stress magnitude in the models shows the same pattern, in accord with experiments showing N proportional to e(k-sigma), with k a constant and sigma the stress magnitude. The models predict downdip compression in the slabs at depths below 300-400 km, as observed for earthquake stress axes.

Vassiliou, M. S.↗

NASA NTRS1987

Transform fault earthquakes in the North Atlantic: Source mechanisms and depth of faulting

The centroid depths and source mechanisms of 12 large earthquakes on transform faults of the northern Mid-Atlantic Ridge were determined from an inversion of long-period body waveforms. The earthquakes occurred on the Gibbs, Oceanographer, Hayes, Kane, 15 deg 20 min, and Vema transforms. The depth extent of faulting during each earthquake was estimated from the centroid depth and the fault width. The source mechanisms for all events in this study display the strike slip motion expected for transform fault earthquakes; slip vector azimuths agree to 2 to 3 deg of the local strike of the zone of active faulting. The only anomalies in mechanism were for two earthquakes near the western end of the Vema transform which occurred on significantly nonvertical fault planes. Secondary faulting, occurring either precursory to or near the end of the main episode of strike-slip rupture, was observed for 5 of the 12 earthquakes. For three events the secondary faulting was characterized by reverse motion on fault planes striking oblique to the trend of the transform. In all three cases, the site of secondary reverse faulting is near a compression jog in the current trace of the active transform fault zone. No evidence was found to support the conclusions of Engeln, Wiens, and Stein that oceanic transform faults in general are either hotter than expected from current thermal models or weaker than normal oceanic lithosphere.

Bergman, Eric A.↗

NASA NTRS1988

Diurnal variations in optical depth at Mars: Observations and interpretations

Viking lander camera images of the Sun were used to compute atmospheric optical depth at two sites over a period of 1 to 1/3 martian years. The complete set of 1044 optical depth determinations is presented in graphical and tabular form. Error estimates are presented in detail. Optical depths in the morning (AM) are generally larger than in the afternoon (PM). The AM-PM differences are ascribed to condensation of water vapor into atmospheric ice aerosols at night and their evaporation in midday. A smoothed time series of these differences shows several seasonal peaks. These are simulated using a one-dimensional radiative convective model which predicts martial atmospheric temperature profiles. A calculation combining these profiles with water vapor measurements from the Mars Atmospheric Water Detector is used to predict when the diurnal variations of water condensation should occur. The model reproduces a majority of the observed peaks and shows the factors influencing the process. Diurnal variation of condensation is shown to peak when the latitude and season combine to warm the atmosphere to the optimum temperature, cool enough to condense vapor at night and warm enough to cause evaporation at midday.

Colburn, D. S.↗

NASA NTRS1987

Effect of current on spectrum of breaking waves in water of finite depth

This paper presents an approximate method to compute the mean value, the mean square value and the spectrum of waves in water of finite depth taking into account the effect of wave breaking with or without the presence of current. It is assumed that there exists a linear and Gaussian ideal wave train whose spectrum is first obtained using the wave energy flux balance equation without considering wave breaking. The Miche wave breaking criterion for waves in finite water depth is used to limit the wave elevation and establish an expression for the breaking wave elevation in terms of the elevation and its second time derivative of the ideal waves. Simple expressions for the mean value, the mean square value and the spectrum are obtained. These results are applied to the case in which a deep water unidirectional wave train, propagating normally towards a straight shoreline over gently varying sea bottom of parallel and straight contours, encounters an adverse steady current whose velocity is assumed to be uniformly distributed with depth. Numerical results are obtained and presented in graphical form.

Tung, C. C.↗