Grain boundary strain localization in a CdTe solar cell revealed by scanning 3D X-ray diffraction microscopy
Scanning 3DXRD was used to visualize strain localization at grain boundaries with a high spatial resolution of 100 nm.
Shukla, Aditya↗
SEARCH · Engineering Papers
Results for “defect size distribution”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Investigation of the Effect of Etch Pits on the Material Properties of Carbon Fiber Structures
It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.
PuMA↗
Pushing the limits of size selectivity in nanoscale solute separations
Transport of a spherical solute through a cylindrical pore has been modelled for decades using well-established hindered transport theory, predicting solutes with a size smaller than the pore to be rejected nonetheless because of convective and diffusive hindrance; this rejection mechanism prevents extremely sharp solute separations by a membrane. Whereas the model has been historically verified, solute transport through near-perfect isoporous membranes may finally overcome this limitation. Here, in this study, encouraging solute rejections are achieved using nanofabricated, defect-free silicon nitride isoporous membranes. The membrane is challenged by a recirculated feed to increase the opportunity for interactions between solutes and the pore array. Results show the membrane completely reject solutes with greater size than the pore size while effectively allowing smaller solutes to permeate through. With effectively increasing the number of interactions, we propose that a steeper size-selective rejection curve may be achieved. With this traditional hurdle overcome, there is new promise for unprecedented membrane separations through judicious process design and extremely tight pore-size distributions.
Gao, Feng↗
Artifact identification in X-ray diffraction data using machine learning methods
In situ synchrotron high-energy X-ray powder diffraction (XRD) is highly utilized by researchers to analyze the crystallographic structures of materials in functional devices ( e.g. battery materials) or in complex sample environments ( e.g. diamond anvil cells or syntheses reactors). An atomic structure of a material can be identified by its diffraction pattern along with a detailed analysis of the Rietveld refinement which yields rich information on the structure and the material, such as crystallite size, microstrain and defects. For in situ experiments, a series of XRD images is usually collected on the same sample under different conditions ( e.g. adiabatic conditions) yielding different states of matter, or is simply collected continuously as a function of time to track the change of a sample during a chemical or physical process. In situ experiments are usually performed with area detectors and collect images composed of diffraction patterns. For an ideal powder, the diffraction pattern should be a series of concentric Debye–Scherrer rings with evenly distributed intensities in each ring. For a realistic sample, one may observe different characteristics other than the typical ring pattern, such as textures or preferred orientations and single-crystal diffraction spots. Textures or preferred orientations usually have several parts of a ring that are more intense than the rest, whereas single-crystal diffraction spots are localized intense spots owing to diffraction of large crystals, typically >10 µm. In this work, an investigation of machine learning methods is presented for fast and reliable identification and separation of the single-crystal diffraction spots in XRD images. The exclusion of artifacts during an XRD image integration process allows a precise analysis of the powder diffraction rings of interest. When it is trained with small subsets of highly diverse datasets, the gradient boosting method can consistently produce high-accuracy results. The method dramatically decreases the amount of time spent identifying and separating single-crystal diffraction spots in comparison with the conventional method.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
Investigation of the effect of etch pits on the material properties of carbon fiber structures
It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material [1, 2]. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA [3] that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. Figure 1 shows a FiberForm sample with artificially generated pits of varying radii and pit density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography [4]. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.
PuMA↗
A Mechanistic Understanding of Nonclassical Crystal Growth in Hydrothermally Synthesized Sodium Yttrium Fluoride Nanowires
Sodium yttrium fluoride (NaYF 4 ) is an important upconverting material with many potential uses in chemistry, materials science, and biology, which can be synthesized hydrothermally in both cubic (α) and hexagonal (β) crystallographic polymorphs. Understanding the mechanisms underlying the phase conversion between the cubic and hexagonal polymorphs is of great interest to help inform future synthetic efforts, for example in the design of atomically precise quantum materials with well-defined sizes and morphologies. In this work, we use a combination of analytical transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM), powder X-ray diffraction (XRD), in situ liquid cell TEM, atom probe tomography (APT), and extended X-ray absorption fine structure (EXAFS) measurements to show that the hexagonal NaYF 4 nanowires form through a nonclassical crystal growth mechanism involving the formation and subsequent oriented attachment of mesocrystals consisting of cubic (α) phase units. Additionally, EXAFS measurements suggest that substitutional Yb 3+ point defects within NaYF 4 are distributed evenly throughout the crystal lattice without clustering and also that they may exhibit selective substitution into one of the two possible trivalent yttrium sites in the unit cell for hydrothermally synthesized β-NaYF 4 .
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Confined Growth of DNA-Assembled Superlattice Films
Here, we study the assembly of DNA-functionalized nanocubes under lateral confinement in microscale square trenches on a DNA-functionalized substrate. Microfocus small-angle X-ray scattering (SAXS) and scanning electron microscopy (SEM) are used to characterize the superlattices (SLs). The results indicate that nanocubes form simple-cubic SLs with square-prism morphology and a (100) out-of-plane orientation to maximize DNA bonding. In-plane, SLs align with the template, exposing their {100} side facets, and the degree of alignment depends on trench size. Interestingly, the distribution of in-plane orientations determined from SAXS and SEM do not agree, indicating that the internal and external structures of the SLs differ. To understand this discrepancy, X-ray ptychography is employed to image the internal structures of the SLs, revealing that SLs which appear to be single-crystalline in SEM may have subsurface grain boundaries, depending on trench size. SEM reveals that the SLs grow via nucleation and growth of randomly oriented domains, which then coalesce; this mechanism explains the observed dependence of alignment and defect structure on size. Interestingly, crystallization occurs via an unusual growth mode, whereby continuous SL layers grow on top of several misoriented islands. Overall, this work elucidates the effect of lateral confinement on the crystallization of DNA-functionalized nanoparticles and shows how X-ray ptychography can be used to gain insight into nanoparticle crystallization.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Edge States Drive Exciton Dissociation in Ruddlesden–Popper Lead Halide Perovskite Thin Films
Efficient photovoltaic cells based on thin films of solution-processed 2D Ruddlesden–Popper hybrid perovskites (RPPs) represent an exciting breakthrough due to their enhanced tunability and chemical stability relative to those fabricated from 3D phases. However, reports of efficient charge separation and current collection are in apparent contradiction with the well-known enhancement of the exciton binding energy in multilayered halide perovskites, which should lower the device’s internal quantum efficiency and voltage. This controversy has led to various proposals for the electronic and physical structure of RPP thin films, including phase inhomogeneity as the driving force for exciton dissociation and transport. We address this apparent paradox in high-quality hot-cast RPP films by correlating ultrafast transient absorption spectroscopy with X-ray scattering measurements. We show that a hot-casting fabrication method produces highly phase pure n = 3 (BA) 2 (MA) n-1 Pb n I 3n+1 RPP structures. The high-phase purity and large grain sizes allow us to observe vertical transport of excitons via a diffusive process and allow us to determine that charge separation is primarily driven by dissociation at surface localized subgap electronic states. Furthermore, we analyze the differential absorption kinetics in films of varying thickness to directly determine that the excitonic diffusion constant is ~0.18 cm 2 s –1 . We propose that a surface localized structural distortion, observed using surface selective grazing incidence X-ray scattering measurements, is responsible for the creation of the surface localized defect states. We find that the density and spatial distribution of these defect states is a function of preparation conditions.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
Microstructure and fracture in SiC whisker reinforced 2124 aluminum composite
The microstructures of extruded and hot-rolled 2124 Al-15 percent (by weight) SiC whisker composites have been investigated, experimentally. Among the specific factors studied were: the strength of the whisker-matrix interfaces; (2) the presence of oxides; (3) the presence of defective whiskers; (4) and the presence of distribution of intermetallic compounds, impurities in the SiC(w) powder, and microstructural inhomogeneities. Modifications in the microstructure of the SiC/AL composites due to hot rolling and extrusion are illustrated in a series of microphotographs. It was found that hot rolling along the axis of extrusion was associated with some types of whisker damage, while the whiskers still retain their original orientation. Hot-rolling perpendicular to the axis of extrusion, however, tended to rotate the whiskers and produced a nearly isotropic material. Whisker free zones were virtually eliminated or reduced in size by hot rolling. In situ Auger fractography of the composite showed that the interfacial bonding between the SiC and the Al matrix was good and that Al2O2 had no significant influence on the fracture mechanics of the composite.
Nieh, T. G.↗
In Situ Micro-Pillar Compression to Examine Radiation-Induced Hardening Mechanisms of FeCrAl Alloys
Here, the effects of 5 MeV Fe 2+ ion irradiation at 300°C on the microstructure evolution and deformation behavior of a FeCrAl C26M alloy are presented. It has been found that dislocation loop density increases an order of magnitude from 1 dpa to 16 dpa irradiations, whereas, the dislocation loop size saturates with increasing damage. Micropillars, 600 nm in diameter and 1.3 µm in height, were fabricated and compressed inside grains with <001>, <011> and <111> crystallographic orientations, respectively. {112} <111> has been identified as the primary slip system in both unirradiated and irradiated alloy. The increase in yield stress after irradiation is observed with measurable variation along <001> and <011> vs. along <111>. By applying the Orowan dispersed barrier model, the increase of yield stress is found mainly due to the slip resistance of radiation generated defect loops. Detailed transmission electron microscopy (TEM) studies were performed to quantify the Burgers vector and the distribution of irradiation induced dislocations at elevated strains. It is revealed that localized shear instability is caused by avalanche slip events of ½<111> dislocations gliding out of tested pillars. Simultaneously, a large number of sessile/immobile <100> dislocations formed in the vicinity of slip band, leading to the hardening at elevated strains.
36 MATERIALS SCIENCE↗
Curing process and pore structure of metakaolin-based geopolymers: Liquid-state 1H NMR investigation
Geopolymers are emerging construction materials with lower carbon dioxide emissions compared to the conventional cementitious materials. The knowledge of the curing process and the related pore structures are important for optimizing the properties of these materials for different applications. The curing process and final pore structure are sensitive to the amount of used water, however the specifics are unclear. The curing process and pore structures of metakaolin-based geopolymers with a narrow water-to-solid (w/s) ratio (0.59–0.66) were monitored by nuclear magnetic resonance (NMR) relaxometry and cryoporometry. The 14-day curing process was investigated by monitoring the change of T{sub 2} and T{sub 1} relaxation times and water signal intensity. After the curing, the pore structures were characterized by 2D T{sub 1}-T{sub 2} correlation and T{sub 2}-T{sub 2} exchange measurements of absorbed water. The pore size distributions (PSDs) were measured with NMR cryoporometry and compared to nitrogen physisorption and mercury intrusion porosimetry (MIP) results. We found that the relaxation times decreased as the pore structure of the geopolymers matured during the curing while the dissolution and the condensation periods of the curing were distinguished by the changes in signal amplitude reflecting the proton density. After the curing, three distinct pore sizes and connectivity between pores were identified from T{sub 1}-T{sub 2} and T{sub 2}-T{sub 2} spectra. Their PSDs were measured, and they were found to correspond to two different pore sizes originating from the arrangement of clusters and defective pores. In the narrow w/s ratio (0.59–0.66), the curing times were the same for all samples when cured at 24 °C while the pore sizes were observed to increase as a function of the w/s ratio.
36 MATERIALS SCIENCE↗
Prediction of Performance Variation Caused by Manufacturing Tolerances and Defects in Gas Diffusion Electrodes of Phosphoric Acid (PA)–Doped Polybenzimidazole (PBI)-Based High-Temperature Proton Exchange Membrane Fuel Cells
The automated process of coating catalyst layers on gas diffusion electrodes (GDEs) for high-temperature proton exchange membrane fuel cells results inherently into a number of defects. These defects consist of agglomerates in which the platinum sites cannot be accessed by phosphoric acid and which are the consequence of an inconsistent coating, uncoated regions, scratches, knots, blemishes, folds, or attached fine particles—all ranging from μm to mm size. These electrochemically inactive spots cause a reduction of the effective catalyst area per unit volume (cm2/cm3) and determine a drop in fuel cell performance. A computational fluid dynamics (CFD) model is presented that predicts performance variation caused by manufacturing tolerances and defects of the GDE and which enables the creation of a six-sigma product specification for Advent phosphoric acid (PA)-doped polybenzimidazole (PBI)-based membrane electrode assemblies (MEAs). The model was used to predict the total volume of defects that would cause a 10% drop in performance. It was found that a 10% performance drop at the nominal operating regime would be caused by uniformly distributed defects totaling 39% of the catalyst layer volume (~0.5 defects/μm2). The study provides an upper bound for the estimation of the impact of the defect location on performance drop. It was found that the impact on the local current density is higher when the defect is located closer to the interface with the membrane. The local current density decays less than 2% in the presence of an isolated defect, regardless of its location along the active area of the catalyst layer.
Gurau, Vladimir (ORCID:0000000327429061)↗
Screening and Qualification of BME Feedthrough Capacitors for a Space Project
Surface mount technology feedthrough ceramic capacitors are gaining popularity in Hi-Rel systems due to small size and great filtering characteristics. In this work, BME feedthrough capacitors compliant with AEC-Q200 requirements have been evaluated, screened and qualified for a space project. Evaluation included analysis of the effect of post-soldering thermal shocks, temperature dependencies of leakage currents, distribution of breakdown voltages, assessments of high-current capability, and thermal resistance of the parts. The parts have been screened and qualified at conditions close to the military requirements for ceramic capacitors. No failures were detected during screening including burning-in, but two samples failed during monitored 2000 hour life testing at 125C and two times rated voltage. Failure analysis revealed manufacturing defects that required additional analysis of screening and qualification test conditions. Highly accelerated life testing (HALT) has been carried out to assess reliability acceleration factors and the probability of failure at the use conditions. An approach to selection of adequate burning-in and life test conditions is discussed.
Alexander Teverovsky↗
Screening and Qualification of BME Feedthrough Capacitors for a Space Project
Surface mount technology feedthrough ceramic capacitors are gaining popularity in Hi-Rel systems due to small size and great filtering characteristics. In this work, BME feedthrough capacitors compliant with AEC-Q200 requirements have been evaluated, screened and qualified for a space project. Evaluation included analysis of the effect of post-soldering thermal shocks, temperature dependencies of leakage currents, distribution of breakdown voltages, assessments of high-current capability, and thermal resistance of the parts. The parts have been screened and qualified at conditions close to the military requirements for ceramic capacitors. No failures were detected during screening including burning-in, but two samples failed during monitored 2000 hour life testing at 125C and two times rated voltage. Failure analysis revealed manufacturing defects that required additional analysis of screening and qualification test conditions. Highly accelerated life testing (HALT) has been carried out to assess reliability acceleration factors and the probability of failure at the use conditions. An approach to selection of adequate burning-in and life test conditions is discussed.
Alexander Teverovsky↗
Single-Crystallization of O3-Type Layered Oxide Cathode for Na-Ion Battery
The development of high-energy-density Na-ion batteries places significant demands on single-crystal layered oxide cathodes, especially for further high-voltage, solid-state battery scenarios. In the O3-type structure, due to the original sluggish Na ion diffusion kinetics (approximately 1 order of magnitude lower than that of Li-ion), and further hindrance against diffusion kinetics caused by single-crystal architecture, these inherent defects lead to the decline in the electrochemical performance. Herein, we demonstrated that the single crystallization of O3-type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 cathode (d 50 = 5.04 μm) aggravates surface-to-bulk phase inhomogeneity distribution, which is attributed to the uneven Na ions extraction. Moreover, the Na-depletion of the surface/shell region not only aggravates Na ion diffusion resistance but also leads to a higher valence state of transition-metal elements (e.g., Ni/Fe) near the surface of the single-crystal particle, which further compromises the cathode-electrolyte interface stability. Furthermore, not limited to revealing the challenges, tuning the particle size and moderating quasi-single-crystal strategies have been proven to effectively mitigate the negative uneven distributions of Na ions, phases, and valence/oxidative states, resulting in efficient modification for single crystallization of Na-layered oxide cathodes.
36 MATERIALS SCIENCE↗
Scaling effects of defects in fiber-reinforced composites
Material defects may be introduced willingly or unwillingly during material manufacturing and structural component fabrication stages. Their presence in the material plays a dominant role in determining the material's strength and the associate failure mechanisms. In the sense that the size and the number of defects may increase with the volume of the material, the effect of dimensional scaling may manifest itself in the dependence of material strength on volume. Or, alternatively, there may exist a scaling effect of material defects. In fiber-reinforced composites, manufacturing or fabrication defects may come in several forms: matrix voids, matrix microcracks, fiber misalignment, broken fibers, or interface disbonds, just to mention a few. These are interacting and competing defects in the sense that one type of defect may become dominant under one stress condition and another type of defect may become dominant under a different stress condition. This happens because the fiber reinforcement network, together with the distribution of defects, constitutes the prime microstructure of the composite, and there exist continued interactions between the evolving microstructure and the distribution of defects. In the process, the scaling effects of defects are complicated by this interaction. In this presentation, the scaling effects of defects in fiber-reinforced composites will be briefly discussed with the introduction of the concept of effective defects. It is then shown with the aid of some actual experimental and analysis results that the scaling effects are very much present, but they are regulated by the characteristic dimension of the composite microstructure due to the aforementioned microstructure-defect interaction effect.
Wang, A. S. D.↗
Silicon Carbide Solar Cells Investigated
The semiconductor silicon carbide (SiC) has long been known for its outstanding resistance to harsh environments (e.g., thermal stability, radiation resistance, and dielectric strength). However, the ability to produce device-quality material is severely limited by the inherent crystalline defects associated with this material and their associated electronic effects. Much progress has been made recently in the understanding and control of these defects and in the improved processing of this material. Because of this work, it may be possible to produce SiC-based solar cells for environments with high temperatures, light intensities, and radiation, such as those experienced by solar probes. Electronics and sensors based on SiC can operate in hostile environments where conventional silicon-based electronics (limited to 350 C) cannot function. Development of this material will enable large performance enhancements and size reductions for a wide variety of systems--such as high-frequency devices, high-power devices, microwave switching devices, and high-temperature electronics. These applications would supply more energy-efficient public electric power distribution and electric vehicles, more powerful microwave electronics for radar and communications, and better sensors and controls for cleaner-burning, more fuel-efficient jet aircraft and automobile engines. The 6H-SiC polytype is a promising wide-bandgap (Eg = 3.0 eV) semiconductor for photovoltaic applications in harsh solar environments that involve high-temperature and high-radiation conditions. The advantages of this material for this application lie in its extremely large breakdown field strength, high thermal conductivity, good electron saturation drift velocity, and stable electrical performance at temperatures as high as 600 C. This behavior makes it an attractive photovoltaic solar cell material for devices that can operate within three solar radii of the Sun.
Bailey, Sheila G.↗
Plasmonic photoconductive terahertz focal-plane array with pixel super-resolution
Abstract Imaging systems operating in the terahertz part of the electromagnetic spectrum are attractive due to their ability to penetrate many opaque materials and provide unique spectral signatures of various chemicals. However, the use of terahertz imagers in real-world applications has been limited by the slow speed, large size, high cost and complexity of present systems, largely due to the lack of suitable terahertz focal-plane array detectors. Here we report a terahertz focal-plane array that can directly provide the spatial amplitude and phase distributions, along with the ultrafast temporal and spectral information of an imaged object. It consists of a two-dimensional array of ~0.3 million plasmonic photoconductive nanoantennas optimized to rapidly detect broadband terahertz radiation with a high signal-to-noise ratio. We utilized the multispectral nature of the amplitude and phase data captured by these plasmonic nanoantennas to image different objects, including super-resolved etched patterns in a silicon substrate and defects in battery electrodes. By eliminating the need for raster scanning and spatial terahertz modulation, our terahertz focal-plane array offers more than a 1,000-fold increase in the imaging speed compared with the state of the art and potentially suits a broad range of applications in industrial inspection, security screening and medical diagnosis, among others.
Optics↗