Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Results of an investigation of jet plume effects on a 0.010-scale model (75-OTS) of the space shuttle integrated vehicle in the 8 x 7-foot leg of the NASA/Ames unitary wind tunnel (IA82C), volume 1

The primary test objective was to define the base pressure environment of the first and second stage mated vehicle in a supersonic flow field from Mach 2.60 through 3.50 with simulated rocket engine exhaust plumes. The secondary objective was to obtain the pressure environment of the Orbiter at various vent port locations at these same freestream conditions. Data were obtained at angles of attack from -4 deg through +4 deg at zero yaw, and at yaw angles from -4 deg through +4 deg at zero angle of attack, with rocket plume sizes varying from smaller than nominal to much greater than nominal. Failed Orbiter engine data were also obtained. Elevon hinge moments and wing panel load data were obtained during all runs. Photographs of test equipment and tested configurations are shown.

Hawthorne, P. J.↗
NASA NTRS1981

Aerodynamic and acoustic behavior of a YF-12 inlet at static conditions

An aeroacoustic test program to determine the cause of YF-12 inlet noise suppression was performed with a YF-12 aircraft at ground static conditions. Data obtained over a wide range of engine speeds and inlet configurations are reported. Acoustic measurements were made in the far field and aerodynamic and acoustic measurements were made inside the inlet. The J-58 test engine was removed from the aircraft and tested separately with a bellmouth inlet. The far field noise level was significantly lower for the YF-12 inlet than for the bellmouth inlet at engine speeds above 5500 rpm. There was no evidence that noise suppression was caused by flow choking. Multiple pure tones were reduced and the spectral peak near the blade passing frequency disappeared in the region of the spike support struts at engine speeds between 6000 and 6600 rpm.

Bangert, L. H.↗
NASA NTRS1981

The Inertial Upper Stage - A space transportation system element nearing first flight

The Inertial Upper Stage (IUS) developed by the USAF and NASA is a highly reliable, cost-effective solid propellant upper stage, with inherent flexibility and adaptability for integration with the Space Shuttle. The propulsion system is simple, utilizing safe, solid rocket motors with extremely light-weight nonmetallic cases and nozzles. The IUS can deliver 2268 kg from the Shuttle to geosynchronous altitude; it consists of a 9700 kg propellant weight first stage, an interstage structure, a 2720 kg propellant weight second stage, and an equipment support section. The avionics system includes the electronic and electrical hardware used to perform all signal conditioning, data processing, and software formatting associated with navigation, guidance, control, data management, and redundancy management. The generic thermal design of the IUS is suited to a wide range of thermal environments; the software design provides for selectable thermal maneuvers (rotisserie, reciprocating, toasting, space facing, sun facing) to satisfy different payload thermal requirements. A 1982 launch with the Titan 34D and a 1983 launch with the Shuttle Orbiter are planned.

Rohrbaugh, D. J.↗
NASA NTRS1982

Effect of tip vanes on the performance and flow field of a rotor in hover

Tests run with a single bladed model rotor with a vane located at the tip of the blade indicated significantly increased performance under certain test conditions. Data reveal that a figure of merit increase of over one third occurred in hover. Flow visualization using smoke revealed that a pair of vortices sprung from the blade tip and the vane tip. The vane tip vortex tended to roll up and over the primary vortex. The vortices in the wake became much less well defined with the tip vane configurations.

Velkoff, H. R.↗
NASA NTRS1983

Creep fatigue of low-cobalt superalloys: Waspalloy, PM U 700 and wrought U 700

The influence of cobalt content on the high temperature creep fatigue crack initiation resistance of three primary alloys was evaluated. These were Waspalloy, Powder U 700, and Cast U 700, with cobalt contents ranging from 0 up to 17 percent. Waspalloy was studied at 538 C whereas the U 700 was studied at 760 C. Constraints of the program required investigation at a single strain range using diametral strain control. The approach was phenomenological, using standard low cycle fatigue tests involving continuous cycling tension hold cycling, compression hold cycling, and symmetric hold cycling. Cycling in the absence of or between holds was done at 0.5 Hz, whereas holds when introduced lasted 1 minute. The plan was to allocate two specimens to the continuous cycling, and one specimen to each of the hold time conditions. Data was taken to document the nature of the cracking process, the deformation response, and the resistance to cyclic loading to the formation of small cracks and to specimen separation. The influence of cobalt content on creep fatigue resistance was not judged to be very significant based on the results generated. Specific conclusions were that the hold time history dependence of the resistance is as significant as the influence of cobalt content and increased cobalt content does not produce increased creep fatigue resistance on a one to one basis.

Leis, B. N.↗
NASA NTRS1983

A study of plasmaspheric density distributions for diffusive equilibrium conditions

The plasmaspheric density distribution has been modeled for a range of solar cycle, seasonal and diurnal conditions with a magnetic flux tube dependent diffusive equilibrium model by using experimentally determined values of ionospheric parameters at 675 km as boundary conditions. Data is presented in terms of plasmaspheric H(+) and He(+) density contours, total flux tube content, and equatorial plasma density for a range of L-values from 1.15 to 3.0. The variation of equatorial density with L-value shows good agreement with the 1/L exp 4 dependence observed experimentally. The results show that the model predicts larger solar cycle and diurnal variation in equatorial plasma density than observed using whistler techniques. However, the whistler method requires a model to deduce the equatorial density and is therefore open to interpretation. Seasonal variations are rather artificial since in this general model no attempt has been made to match equatorial densities for flux tubes emanating from the winter and summer hemispheres.

Li, W.↗
NASA NTRS1984

Spatial estimation from remotely sensed data via empirical Bayes models

Multichannel satellite image data, available as LANDSAT imagery, are recorded as a multivariate time series (four channels, multiple passovers) in two spatial dimensions. The application of parametric empirical Bayes theory to classification of, and estimating the probability of, each crop type at each of a large number of pixels is considered. This theory involves both the probability distribution of imagery data, conditional on crop types, and the prior spatial distribution of crop types. For the latter Markov models indexed by estimable parameters are used. A broad outline of the general theory reveals several questions for further research. Some detailed results are given for the special case of two crop types when only a line transect is analyzed. Finally, the estimation of an underlying continuous process on the lattice is discussed which would be applicable to such quantities as crop yield.

Hill, J. R.↗
NASA NTRS1985

On the penetration of a hot diapir through a strongly temperature-dependent viscosity medium

The ascent of a hot spherical body through a fluid with a strongly temperature-dependent viscosity has been studied using an axisymmetric finite element method. Numerical solutions range over Peclet numbers of 0.1 - 1000 from constant viscosity up to viscosity variations of 100,000. Both rigid and stress-free boundary conditions were applied at the surface of the sphere. The dependence of drag on viscosity variation was shown to have no dependence on the stress boundary condition except for a Stokes flow scaling factor. A Nusselt number parameterization based on the stress-free constant viscosity functional dependence on the Peclet number scaled by a parameter depending on the viscosity structure fits both stress-free and rigid boundary condition data above viscosity variations of 100. The temperature scale height was determined as a function of sphere radius. For the simple physical model studied in this paper pre-heating is required to reduce the ambient viscosity of the country rock to less than 10 to the 22nd sq cm/s in order for a 10 km diapir to penetrate a distance of several radii.

Daly, S. F.↗
NASA NTRS1985

NASA storm hazards research in lightning strikes to aircraft

The lightning strike condition data gathered in the 1980-1984 period are presented, together with the lightning attachment point analysis for the NASA F-106B research aircraft are presented. The analysis of the experienced 637 direct lightning strikes shows that the highest strike rates (2.1 strikes/min and 13 strikes/penetration) occurred at altitudes between 38,000 and 40,000 ft. The regions of highest risk for an aircraft to experience a direct lightning strike were the areas of thunderstorms where the ambient temperature was colder than -40 C and where the relative turbulence and precipitation intensities were characterized as negligible to light. The presence and location of lightning, therefore, did not necessarily indicate the presence and location of hazardous precipitation and turbulence. The total onboard data show that the lightning attachment patterns on this aircraft fall into four general categories, although the 1984 data suggest that the entire surface of the F-106B may be susceptible to lightning attachment.

Fisher, B. D.↗
NASA NTRS1987

Effects of ground proximity on a low aspect ratio propulsive wing/canard configuration

The effect of near proximity to the ground are investigated on a low aspect ratio propulsive wing/canard concept at STOL conditions. Data were obtained on a wing/body and wing/body/canard configuration at various heights above the ground, ranging from free air to approximately 1/4 of the mean aerodynamic chord (MAC) above the ground. The data presented and discussed include force and moment coefficients, surface pressure distributions, and downwash angles measured one MAC behind the wing. The test technique, model requirements, and special considerations required for testing these configurations are also discussed. Special model requirements included evenly distributed exit nozzle pressures along four separate nozzles of lengths of one and two feet with only one air supply to the model. Test techniques must recognize and deal with the ground boundary layer as well as the air supply pressure measurement and management.

Stewart, V. R.↗
NASA NTRS1989

Laser anemometer measurements in a transonic axial-flow fan rotor

Laser anemometer surveys were made of the 3-D flow field in NASA rotor 67, a low aspect ratio transonic axial-flow fan rotor. The test rotor has a tip relative Mach number of 1.38. The flowfield was surveyed at design speed at near peak efficiency and near stall operating conditions. Data is presented in the form of relative Mach number and relative flow angle distributions on surfaces of revolution at nine spanwise locations evenly spaced from hub to tip. At each spanwise location, data was acquired upstream, within, and downstream of the rotor. Aerodynamic performance measurements and detailed rotor blade and annulus geometry are also presented so that the experimental results can be used as a test case for 3-D turbomachinery flow analysis codes.

Strazisar, Anthony J.↗
NASA NTRS1991

Results of the recent precipitation static flight test program on the Navy P-3B antisubmarine aircraft

Severe precipitation static problems affecting the communication equipment onboard the P-3B aircraft were recently studied. The study was conducted after precipitation static created potential safety-of-flight problems on Naval Reserve aircraft. A specially designed flight test program was conducted in order to measure, record, analyze, and characterize potential precipitation static problem areas. The test program successfully characterized the precipitation static interference problems while the P-3B was flown in moderate to extreme precipitation conditions. Data up to 400 MHz were collected on the effects of engine charging, precipitation static, and extreme cross fields. These data were collected using a computer controlled acquisition system consisting of a signal generator, RF spectrum and audio analyzers, data recorders, and instrumented static dischargers. The test program is outlined and the computer controlled data acquisition system is described in detail which was used during flight and ground testing. The correlation of test results is also discussed which were recorded during the flight test program and those measured during ground testing.

Whitaker, Mike↗
NASA NTRS1991

A correlational analysis of the effects of changing environmental conditions on the NR atomic hydrogen maser

An extensive statistical analysis has been undertaken to determine if a correlation exists between changes in an NR atomic hydrogen muser's frequency offset and changes in environmental conditions. Data have been acquired over the past 20 months by recording the frequency offset of three NR atomic hydrogen masers along with the relative and absolute humidity, barometric pressure, and ambient temperature of the laboratory in which the masers are maintained. Correlational analyses have been performed comparing barometric pressure, humidity, and temperature with maser frequency offset as functions of time for periods ranging from 5.5 to 17 days. Semi partial correlation coefficients as large as -0.9 have been fond between barometric pressure and maser frequency offset for data covering periods as long as a week. Maser frequency offset and barometric pressure were consistently found to change simultaneously. The correlation between humidity and frequency offset is less predictable, and the resulting semi partial correlation coefficients were usually small when compared with those derived from the relationship between pressure and frequency offset. The time delay between changes in humidity and correlated changes in maser frequency offset was found to vary extensively with no predictable pattern. Analysis of temperature data indicates that, in the most current design, temperature does not significant(y affect maser frequency offset in the laboratory environment. Thus, the results of the analyses disclose a significant statistical correlation between changes in maser frequency offset and changes in barometric pressure. The statistics also reveal some correlation between humidity and frequency offset, bat for reasons to be discussed, the effects of humidity should be considered secondary to the effects of changing barometric pressure.

R. A. Dragonette↗
NASA NTRS1993

Navier-Stokes simulations of the Shuttle Orbiter aerodynamic characteristics with emphasis on pitch trim and bodyflap

An analysis of the longitudinal aerodynamics of the Shuttle Orbiter in the hypersonic flight regime is made through the use of computational fluid dynamics (CFD). Particular attention is given to establishing the cause of the 'pitching moment anomaly' which occurred on the Orbiter's first flight and to computing the aerodynamics of a complete Orbiter configuration at flight conditions. Data from ground based facilities as well as Orbiter flight data are used to validate the computed results. Analysis shows that the 'pitching moment anomaly' is a real gas chemistry effect which cannot be simulated in ground-based facilities. Computed flight aerodynamics for the Orbiter are within 5 percent of the measured flight values and trim bodyflap deflections are predicted to within 10 percent.

Weilmuenster, K. J.↗
NASA NTRS1953

Investigation of acceleration characteristics of a single-spool turbojet engine

Operation of a single-spool turbojet engine with constant exhaust-nozzle area was investigated at one flight condition. Data were obtained by subjecting the engine to approximate-step changes in fuel flow, and the information necessary to show the relations of acceleration to the sensed engine variables was obtained. These data show that maximum acceleration occurred prior to stall and surge. In the low end of the engine-speed range the margin was appreciable; in the high-speed end the margin was smaller but had not been completely defined by these data. Data involving acceleration as a function of speed, fuel flow, turbine-discharge temperature, compressor-discharge pressure, and thrust have been presented and an effort has been made to show how a basic control system could be improved by addition of an override in which the acceleration characteristic is used not only to prevent the engine from entering the surge region but also to obtain acceleration along the maximum acceleration line during throttle bursts.

Oppenheimer, Frank L↗
NASA NTRS1948

Altitude-wind-tunnel investigation of Westinghouse 19B-2, 19B-8, and 19XB-1 jet-propulsion engines III : performance and windmilling drag characteristics

The performance characteristics of the 19B-8 and 19XB-1 turbojet engines and the windmilling drag characteristics of the 19B-8 engine were determined in the NACA Cleveland altitude wind tunnel. The 19B engine is one of the earliest experimental Westinghouse axial-flow engines. The 19XB-1 engine is an experimental prototype of the Westinghouse 19XB series, having a rated thrust of 1400 pounds. Improvements in performance and operational characteristics have resulted in the 19XB-2B engine with a rated thrust of 1600 pounds. The investigations were conducted on the 19B-8 engine at simulated altitudes from 5000 to 25,000 feet with various free-stream ram-pressure ratios and on the 19XB-1 engine at simulated altitudes from 5000 to 30,000 feet with approximately static free-stream conditions. Data for these two engines are presented to show the effect of altitude, free-stream ram-pressure ratio, and tail-pipe-nozzle area on engine performance.

Fleming, William A↗
NASA NTRS1952

Dynamic response at altitude of a turbojet engine with variable area exhaust nozzle

The dynamic characteristics of turbojet engine with variable exhaust nozzle area were investigated over a range of altitudes and flight Mach numbers. These characteristics generalize to standard static level condition. Data resulting from approximate step disturbances in either manipulated variable suggested functional relationships from which functions can be derived. The constants of the transfer functions are listed for five combinations of engine speed and exhaust nozzle area. The minimum data needed to completely define the transfer functions were: experimentally determined dynamic characteristics, such as engine time constant and initial rise ratio, resulting from either manipulated variable; static characteristics determined from steady-state performance curves.

Delio, Gene J↗
NASA NTRS1994

Wind tunnel test of a variable-diameter tiltrotor (VDTR) model

This report documents the results from a wind tunnel test of a 1/6th scale Variable Diameter Tiltrotor (VDTR). This test was a joint effort of NASA Ames and Sikorsky Aircraft. The objective was to evaluate the aeroelastic and performance characteristics of the VDTR in conversion, hover, and cruise. The rotor diameter and nacelle angle of the model were remotely changed to represent tiltrotor operating conditions. Data is presented showing the propulsive force required in conversion, blade loads, angle of attack stability and simulated gust response, and hover and cruise performance. This test represents the first wind tunnel test of a variable diameter rotor applied to a tiltrotor concept. The results confirm some of the potential advantages of the VDTR and establish the variable diameter rotor a viable candidate for an advanced tiltrotor. This wind tunnel test successfully demonstrated the feasibility of the Variable Diameter rotor for tilt rotor aircraft. A wide range of test points were taken in hover, conversion, and cruise modes. The concept was shown to have a number of advantages over conventional tiltrotors such as reduced hover downwash with lower disk loading and significantly reduced longitudinal gust response in cruise. In the conversion regime, a high propulsive force was demonstrated for sustained flight with acceptable blade loads. The VDTR demonstrated excellent gust response capabilities. The horizontal gust response correlated well with predictions revealing only half the response to turbulence of the conventional civil tiltrotor.

Matuska, David↗