Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “crystallographic structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Molecular-Level Structure and Packing in Phase-Separated Arachidic Acid–Perfluorotetradecanoic Acid Monolayer Films

Synchrotron-based X-ray scattering measurements of phase-separated surfactant monolayers at the air–water interface provide molecular-level structural information about the packing and ordering of film components. In this work, grazing incidence X-ray diffraction (GIXD) and X-ray reflectivity (XR) measurements were used to collect crystallographic structural information for binary mixed monolayers of arachidic acid (AA, C 19 H 39 COOH) with perfluorotetradecanoic acid (PA, C 13 F 27 COOH), a system that has previously been investigated using a variety of thermodynamic and micron-scale structural characterization methods. GIXD measurements at surface pressures of π = 5, 15, and 30 mN/m indicated that AA in pure and mixed films forms a rectangular lattice at π = 5 and 15 mN/m but a hexagonal lattice at π = 30 mN/m. PA formed hexagonal lattices under all conditions, with films being highly ordered and crystalline (as determined by Bragg peak width) at even the lowest surface pressures investigated. Phase separation occurred for all mixed monolayer film compositions and surface pressures, manifesting as diffraction peaks characteristic of the individual components appearing at different in-plane scattering vector q xy . For both pure and mixed films, the molecular tilt angle of the AA hydrocarbon chain toward the nearest-neighbor was substantial at low pressures but decreased with increasing pressure. The PA fluorocarbon chain showed negligible molecular tilt under all conditions, and was oriented normal to the subphase surface regardless of surface pressure or the presence of AA in the films. In all cases, the two components in the mixed film behaved entirely independently of film composition, which is exactly the expected result for a fully phase-separated, immiscible system. XR measurements of film thickness at the air–water interface supported these results; overall film thickness approached the calculated ideal surfactant tail lengths with increasing surface pressure, indicating nearly normal oriented surfactants. Furthermore, the overall surfactant packing and crystallographic features of the mixed monolayers are discussed in terms of the lipophobic nature of the perfluorinated surfactant as well as in context of thermodynamic miscibility and domain structure formation reported elsewhere in the literature for these mixed monolayer systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Epitaxial TiO x Surface in Ferroelectric BaTiO 3 : Native Structure and Dynamic Patterning at the Atomic Scale

Surfaces and interfaces of ferroelectric oxides exhibit enhanced functionality, and therefore serve as a platform for novel nano and quantum technologies. Experimental and theoretical challenges associated with examining the subtle electro-chemo-mechanical balance at metal-oxide surfaces have hindered the understanding and control of their structure and behavior. Here, we combine advanced electron-microscopy and first-principles thermodynamics methods to reveal the atomic-scale chemical and crystallographic structure of the surface of the seminal ferroelectric BaTiO 3 . Here, we show that the surface is composed of a native < 2-nm thick TiOx rock-salt layer in epitaxial registry with the BaTiO 3 . Using electron-beam irradiation, we successfully patterned artificially TiO x sites with sub-nanometer resolution, by inducing Ba escape. Therefore, our work offers electro-chemo-mechanical insights into ferroelectric surface behavior in addition to a method for scalable high-resolution beam-induced chemical lithography for selectively driving surface phase transitions, and thereby functionalizing metal-oxide surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Shear Pleasure: The Structure, Formation, and Thermodynamics of Crystallographic Shear Phases

A renaissance of interest in crystallographic shear structures and our recent work in this remarkable class of materials inspired this review. We first summarize the geometrical aspects of shear plane formation and possible transformations in ReO 3 , rutile, and perovskite-based structures. Then we provide a mechanistic overview of crystallographic shear formation, plane ordering, and propagation. Next we describe the energetics of planar defect formation and interaction, equilibria between point and extended defect structures, and thermodynamic stability of shear compounds. Finally, we emphasize the remaining challenges and propose future directions in this exciting area.

Materials Science↗

Agentic framework for programmatic crystal structure generation using a fine-tuned worker–supervisor large language model

Platinum group metals (PGMs) underpin many catalytic technologies but face severe supply constraints, motivating the search for alternative materials and computational methods to accelerate discovery. While atomistic simulation tools such as Pymatgen and ASE have streamlined structure manipulation, they require detailed inputs, limiting accessibility for experimentalists and slowing early-stage exploration. Here, in this study, we present an AI-driven agentic framework that orchestrates worker–supervisor large language models (LLMs). The worker translates natural-language prompts of varying abstraction into valid crystallographic structures using a compact LLM fine-tuned with low-rank adaptation on a curated text–code–CIF dataset, emphasizing energy-efficient training. Benchmarking against the baseline CodeGen-350M-mono model shows that fine-tuning reduces hallucination rates from 100% to as low as 5% and improves structural match accuracy to up to 82% for fully specified inputs. Accuracy declines with decreasing prompt detail but remains nontrivial even when only stoichiometry and space group are provided, underscoring the LLM’s capacity for crystallographic inference. The supervisor Claude LLM evaluates the outputs and triggers iterative refinement through the worker’s built-in structure manipulation capabilities (e.g., supercell scaling, strain, vacancy, and substitution operations). We further demonstrate use cases for technologically relevant catalysts, including IrO 2 , pyrochlore Pb 2 Ir 2 O 7 , Ni 2 FeO 4 , and Ni 3 Mo, where the framework generates physically consistent structures that can be refined via geometry optimization. This work introduces a low-energy, language-driven pathway for integrating human and machine intelligence in materials design, paving the way for AI-assisted synthesis planning and high-throughput screening of complex oxides.

AI agent↗

Linker Vacancy Engineering of a Robust ftw–type Zr–MOF for Hexane Isomers Separation

Discrimination of physically similar molecules by porous solids represents an important yet challenging task in industrially relevant chemical separations. Precisely controlled pore dimension and/or tailored pore surface functionality are crucial to achieve high-efficiency separation. Metal-organic frameworks (MOFs) are promising candidates for these challenging separations in light of their structural diversity as well as highly adjustable pore dimension/functionality. We report here a microporous, ftw-type Zr-based MOF structure, HIAM-410 (HIAM=Hoffmann Institute of Advanced Materials), built on hexanuclear Zr 6 cluster and pyrene-1,3,6,8-tetracarboxylate (ptc 4– ). Its crystallographic structure has been determined using continuous rotation electron diffraction (cRED) technique combined with Rietveld refinement against powder X-ray diffraction data, aided by low-dose high-resolution transmission electron microscopy (HRTEM) imaging. The compound features exceptional framework stability that is comparable to the prototype MOF UiO-66. Interestingly, the linker vacancies in the pristine MOF structure could be partially restored by post-synthetic linker insertion. Its separation capability of hexane isomers is enhanced substantially upon the linker vacancy engineering. As a result, the restored structure exhibits efficient splitting of monobranched and dibranched hexane isomers at both room temperature and industrially relevant temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tuning giant anomalous Hall resistance ratio in perpendicular Hall balance

Anomalous Hall effect at room temperature in perpendicular Hall balance with a core structure of [Pt/Co]{sub 4}/NiO/[Co/Pt]{sub 4} has been tuned by functional CoO layers, where [Pt/Co]{sub 4} multilayers exhibit perpendicular magnetic anisotropy. A giant Hall resistance ratio up to 69 900% and saturation Hall resistance (R{sub S}{sup P}) up to 2590 mΩ were obtained in CoO/[Pt/Co]{sub 4}/NiO/[Co/Pt]{sub 4}/CoO system, which is 302% and 146% larger than that in the structure without CoO layers, respectively. Transmission electron microscopy shows highly textured [Co/Pt]{sub 4} multilayers and oxide layers with local epitaxial relations, indicating that the crystallographic structure has significant influence on spin dependent transport properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Representational analysis of extended disorder in atomistic ensembles derived from total scattering data

With the increased availability of high-intensity time-of-flight neutron and synchrotron X-ray scattering sources that can access wide ranges of momentum transfer, the pair distribution function method has become a standard analysis technique for studying disorder of local coordination spheres and at intermediate atomic separations. In some cases, rational modeling of the total scattering data (Bragg and diffuse) becomes intractable with least-squares approaches, necessitating reverse Monte Carlo simulations using large atomistic ensembles. However, the extraction of meaningful information from the resulting atomistic ensembles is challenging, especially at intermediate length scales. Representational analysis is used here to describe the displacements of atoms in reverse Monte Carlo ensembles from an ideal crystallographic structure in an approach analogous to tight-binding methods. Rewriting the displacements in terms of a local basis that is descriptive of the ideal crystallographic symmetry provides a robust approach to characterizing medium-range order (and disorder) and symmetry breaking in complex and disordered crystalline materials. Lastly, this method enables the extraction of statistically relevant displacement modes (orientation, amplitude and distribution) of the crystalline disorder and provides directly meaningful information in a locally symmetry-adapted basis set that is most descriptive of the crystal chemistry and physics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Micrometer to Atomic Scale Characterisation of Primitive Astromaterials Using A Novel Method, Metis-Fa: A Coordinated Atom Probe Tomography, Transmission Electron Microscopy and NanoSIMS Approach

Introduction: Presolar grains preserve isotopic, chemical and microstructural records of physical and chemical processing, and formation mechanisms within a vast range of evolved stellar systems, the interstellar medium, solar nebula and their parent bodies. These evolutionary records are preserved at the micrometric to atomic scale, requiring coordinated studies to expand our understanding of evolutionary processes occurringthroughout ours and external stellar systems [1]. NanoSIMS enabled rapid in situ identification and isotopic characterisation of presolar grains and their stellar origins using 17O/16O and 18O/16O, and 13C/12C isotopic ratios [1]. Coordination with transmission electron microscopy (TEM) revealed crystallographic and localised contextual relationships and quantitively constrained their major and minor compositions [1]. However, trace elements cannot be quantified, the most sensitive geochemical tracers of environmental conditions, essential to unravelling the chemical record of their evolutionary pathway and parent stellar systems [2-3] . Furthermore, owing to the combination of technical limitations (only 5 – 7 isotopes can be measured per NanoSIMS run) and their small grain sizes of 100 nm < 3 μm (with rare exceptions in nanodiamonds (2 nm ≤) and SiC (< 40 μm)), the number of measurable isotopes per grain volume is limited [1,3] . Through more comprehensive isotopic studies of presolar grains, NanoSIMS studies have shown the importance of the latter, identifying Fe and Mg as important indicators of nuclear synthetic processing and their stellar origins, respectively [4- 5]. Coordination of NanoSIMS and Atom Probe Tomography (APT) revealed morphological signatures, and isotopic and chemical signatures at major to trace levels without requirements for preselection of elements [6]. However, crystallographic signatures in localized contextual relationships cannot be measured. Consequently, coordination of NanoSIMS, TEM and APT is essential to gain access to almost all contextual, structural and geochemical signatures within each presolar grain.Transmission electron microscopy requires a 100 nm thin lamella which is unstable in APT and would not produce any viable data. Atom probe tomography requires a needle-shaped specimen which when measured in TEM removes the local context, impacts the quality of the TEM diffraction images due to the shank angle of the needle, and can alter the chemistry of beam sensitive materials from the higher degree of surface exposure at the tip. To address these issues, we developed METIS-Fa (Multi-technical measurements of Electron Transparent materials using an Indium Sandwich - a FIB approach). A novel method which enables coordination of NanoSIMS, TEM and APT for generalized and targeted studies of individual grains, including beam sensitive materials, without compromising sample preparation requirements for TEM and APT. This method requires only indium and a Focus Ion Beam (FIB), minimizing the movement of fragile materials while still enabling preparation of TEM lamella into APT needles. Samples: Initial experimental development and testing of the method occurred at Astromaterials Research and Exploration Science (ARES), Johnson Space Centre (JSC), NASA and APT measurements and needle preparation occurred at JdLC, Curtin University. Synthetic silicate samples were used as analogs for presolar silicates when performing a trial run of the method. Samples were extracted from a polished thin section created at JSC, NASA, comprised of 38 wt.% Si, 17 wt.% FeO, 13 wt.% MgO, 12 wt.% Al, 11 wt.% Ca based on electron microprobe analysis (EMPA) [8] . Experimental details, pressure and temperature conditions were presented in [8] and references therein. Testing of the capability to target individual grains in mineral matrices using this method for acquisition in APT, measured matrix regions in meteoritic thin sections of primitive meteorites. These meteorites and their identified presolar grains for future targeted studies are detailed in [9]. Techniques: The TEM-FIB lamella were prepared using a FIB. An e-beam assisted pt deposition was used as a protective coating for the synthetic and meteoritic samples. When targeting individual grains, a secondary e-beam assisted pt deposition button is placed over the desired grain before the protective coating to denote its location. A JEOL 2500SE field-emission TEM was used for high-resolution imaging, energy-dispersive X-ray (EDX) and electron diffraction data.TheMETIS-Fa method was experimentally designed, tested and executed using a FIB at ARES, JSCNASA. Needles for APT were prepared using the Tescan Lyra3 GM Dual Beam Focus Ion Beam (FIB) Field Emission SEM (FE-SEM) at the JdLC, Curtin University. Atom probe tomography measurements were conducted using a CAMECA Local Electrode Atom Probe, LEAP 4000X HR. Two pure indium needles were analyzed initially to constraining acquisition parameters and stability under the beam. Manual acquisition was required to maintain evaporation of specimen’s at the apex and monitor interactions with measurement parameters. Experimental Design: Indium foil is pressed onto an Al stub with a pneumatic press and mounted into the FIB adjacent to the TEM-FIB lamella of interest. Using a FIB, two indium slices (5 μm x ~300 nm x 3 μm) are extracted from indium foil and aligned with the TEM-FIB lamella before touching the TEM-FIB lamella. Each slice is then attached through cold welding to the FIB-TEM lamella. This approach eliminates the need for chemical treatments and proved effective for aligning the Indium within the region of interest for APT, holding it in place for up to 4 days during testing.Once both indium slices are attached within their pre-determined region per grain targeting requirements, they are gradually melted onto the FIB-TEM lamella.When targeting a specific grain, measurements should be taken of the pt button and its distance from edge to edge of the lamella before and after sandwiching. A secondary button should be placed over the same region after the Indium slices have been attached to improve precision when preparing APT needles. Results: Figure 1 shows two indium slices melted onto a FIB-TEM lamella, adding additional bulk for preparation into APT needles as shown in Figure 2 [7] . The latter was essential so samples could be measured in TEM and APT without compromising sample preparation requirements and consequently data quality and acquisition stability. METIS-Fa proved effective forimproving geometry. Figure 3 shows a successful APTrun of the synthetic silicate. EMPA, TEM and APTshowed no chemical alterations. During targetingtesting, a solar silicate grain was successfully identifiedand measured in TEM, and prepared into an APTneedle. However, the indium was melted too long during sample preparation, causing expansion andformation of internal porosity leading to sample loss.Conclusion: METIS-Fa greatly expands the number of isotopic and chemical signatures measured per grain volume, and enables measurements of contextual, structural, crystallographic, isotopic and geochemical signatures within individual grains. Gaining access to such a vast range of evolutionary signatures required for expanding our understanding of external stellar and planetary systems and the evolution of our solar system. This method was designed for application to a vast range of phases including being sensitive materials and thus provides a way for coordination of NanoSIMS, TEM and APT not just for the study of presolar grains and by extension primitive astromaterials, but studies in a vast range of other fields including the geosciences and material sciences.Acknowledgments: Thankyou to ARES, JSC, NASA; JdLC Curtin University and Space Science Technology Centre for the use of laboratory facilities and funding [confirm].

Nicole D Nevill↗

Joint X-ray/neutron structure of Lentinus similis AA9_A at room temperature

Lytic polysaccharide monooxygenases (LPMOs) are copper metalloenzymes which cleave polysaccharides oxidatively and are important in pathogen biology, carbon cycling and biotechnology. The Lentinus similis family AA9 isoform A (LsAA9_A) has been extensively studied as a model system because its activity towards smaller soluble saccharide substrates has allowed detailed structural characterization of its interaction with a variety of substrates by X-ray crystallography at high resolution. Here, the joint X-ray/neutron room-temperature crystallographic structure of carbohydrate-free LsAA9_A in the copper(II) resting state refined against X-ray and neutron data at 2.1 and 2.8 Å resolution, respectively, is presented. The results provide an experimental determination of the protonation states of the copper(II)-coordinating residues and second-shell residues in LsAA9_A, paving the way for future neutron crystallographic studies of LPMO–carbohydrate complexes.

59 BASIC BIOLOGICAL SCIENCES↗

Defects and 3D structural inhomogeneity in electron beam additively manufactured Inconel 718

Highlights: • A protocol for 3D characterization of structure and defects in additively manufactured EBM 718 is presented. • Lack of fusion defects disrupt local microstructure, creating isolated regions of equiaxed grains. • Clustering of micron-scale nitrides is attributed to a particle rafting process. • Normalized size-number density relationship of carbides matches that of industrial ingots. • Removal of porosity via post-processing will not correct microstructural inhomogeneities created by lack of fusion defects. - Abstract: Material structure and defects created during additive manufacturing contribute to the variability in mechanical properties of these parts, limiting their use for critical applications. Three-dimensional crystallographic, structural, and chemical information in electron beam melted Inconel 718 was collected from the sub-micron to the millimeter scale using the TriBeam tomography system. The relationship of defects to the surrounding microstructure has been studied in detail. Lack of fusion defects created sharp discontinuities in the grain morphology that extended several build layers beyond the layer where the defect originated. Nitrides and carbides in the size range of 1.25 μm to 10 μm were observed throughout the volume, with pronounced nitride clustering. The similarities between solidification in additive manufacturing and traditional manufacturing processes are demonstrated by the comparable size and distribution of carbides measured for industrial-scale samples of 718. Defects created during additive manufacturing cannot be easily remedied via standard post-processing techniques, and will likely diminish the mechanical performance of additively manufactured parts.

36 MATERIALS SCIENCE↗

The first 3D malonate bridged copper [Cu(O{sub 2}C-CH{sub 2}-CO{sub 2}H){sub 2}{center_dot}2H{sub 2}O]: Structure, properties and electronic structure

A new inorganic-organic compound [Cu(O{sub 2}C-CH{sub 2}-CO{sub 2}H){sub 2}{center_dot}2H{sub 2}O] ([Cumal]) was hydrothermally synthesized and characterized by IR spectroscopy, thermal analysis and single crystal X-ray diffraction. [Cumal] is the first three-dimensional compound existing in the system Cu(II)-malonic acid-H{sub 2}O. Its framework is built up through carboxyl bridged copper where CuO{sub 6} octahedra are elongated with an almost D{sub 4h} symmetry (4+2) due to the Jahn-Teller effect. The magnetic properties were studied by measuring its magnetic susceptibility in the temperature range of 2-300 K indicating the existence of weak ferromagnetic interactions. The electronic structure of [Cumal] was calculated within the density functional theory (DFT) framework. Structural features are well reproduced using DFT structural optimizations and the optical spectra, calculated within the dielectric formalism, explain very well the light blue colour of the compound. It is shown that a GGA+U approach with a U{sub eff} value of about 6 eV is necessary for a better correlation with the experiment. - Graphical abstract: [Cu(O{sub 2}C-CH{sub 2}-CO{sub 2}H){sub 2}{center_dot}2H{sub 2}O]: the first 3D hybrid organic-inorganic compound built up carboxyl groups. The network presents a diamond-like structure achieved via carboxyl. Highlights: Black-Right-Pointing-Pointer A new organic-inorganic material with an unprecedented topology is synthesized. Black-Right-Pointing-Pointer Crystallographic structure is determined using single crystal X-ray diffraction. Black-Right-Pointing-Pointer Electronic structure is obtained from DFT, GGA+U calculation. Black-Right-Pointing-Pointer Framework can be described as formed from CuC{sub 4} tetrahedron sharing four corners. Black-Right-Pointing-Pointer This structure can be classified as an extended diamond structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The first crystal structure of a xylobiose-bound xylobiohydrolase with high functional specificity from the bacterial glycoside hydrolase family 30, subfamily 10

Xylobiose is a prebiotic sugar that has applications in functional foods. This report describes the first X-ray crystallographic structure models of apo and xylobiose-bound forms of a xylobiohydrolase (XBH) from Acetivibrio clariflavus. This xylan-active enzyme, a member of the recently described glycoside hydrolase family 30 (GH30), subfamily 10, phylogenetic clade has been shown to strictly release xylobiose as its primary hydrolysis product. Inspection of the apo structure reveals a glycone region X-2-binding slot. When X-2 binds, the non-reducing xylose in the -2 subsite is highly coordinated with numerous hydrogen bond contacts while contacts in the -1 subsite mostly reflect interactions typical for GH30 and enzymes in clan A of the carbohydrate-active enzymes database (CAZy). This structure provides an explanation for the high functional specificity of this new bacterial GH30 XBH subfamily.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure of NS1A effector domain from the influenza A/Udorn/72 virus

The structure of the effector domain of the influenza protein NS1, a validated antiviral drug target, has been solved in two space groups. The nonstructural protein NS1A from influenza virus is a multifunctional virulence factor and a potent inhibitor of host immunity. It has two functional domains: an N-terminal 73-amino-acid RNA-binding domain and a C-terminal effector domain. Here, the crystallographic structure of the NS1A effector domain of influenza A/Udorn/72 virus is presented. Structure comparison with the NS1 effector domain from mouse-adapted influenza A/Puerto Rico/8/34 (PR8) virus strain reveals a similar monomer conformation but a different dimer interface. Further analysis and evaluation shows that the dimer interface observed in the structure of the PR8 NS1 effector domain is likely to be a crystallographic packing effect. A hypothetical model of the intact NS1 dimer is presented.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Inferring grain boundary structure–property relations from effective property measurements

Grain boundaries strongly affect many materials properties in polycrystalline materials. Yet, very few structure–property models exist for grain boundaries, due in large part to the complicated and poorly understood way in which the properties of grain boundaries vary with their crystallographic structure. Here, we infer grain boundary structure–property correlations from measurements of the effective properties of a polycrystal. We refer to this method as grain boundary properties localization. We apply this technique to a simple model system of grain boundary diffusivity in a two-dimensional microstructure, and infer the properties of low- and high-angle grain boundaries from the effective diffusivity of the grain boundary network. The generalization and use of these methods could greatly reduce the computational and experimental effort required to establish structure–property correlations for grain boundaries. More broadly, the technique of properties localization could be used to infer the properties of many microstructural constituents in complex microstructures.

54 ENVIRONMENTAL SCIENCES↗

Structural Basis of Inhibitor Selectivity in Human Indoleamine 2,3-Dioxygenase 1 and Tryptophan Dioxygenase

Indoleamine 2,3-dioxygenase 1 (hIDO1) and tryptophan dioxygenase (hTDO) are two of the only three heme-based dioxygenases in humans. They have recently been identified as key cancer immunotherapeutic drug targets. While structures of hIDO1 in complex with inhibitors have been documented, so far there are no structures of hTDO-inhibitor complexes available. In this study, we use PF-06840003 (IPD), a hIDO1-selective inhibitor in clinical trials, as a structural probe to elucidate inhibitor-selectivity in hIDO1 versus hTDO. Spectroscopic studies show that IPD exhibits 400-fold higher inhibition activity toward hIDO1 with respect to hTDO. Crystallographic structures reveal that the binding pocket of IPD in the active site in hIDO1 is much more flexible as compared to that in hTDO, which offers a molecular explanation for the superior inhibition activity of IPD in hIDO1 with respect to hTDO. In addition to the IPD bound in the active site, a second IPD molecule was identified in an inhibitory site on the proximal side of the heme in hIDO1 and in an exosite that is ~40 Å away from the active site in hTDO. Taken together the data provide new insights into structure-based design of mono and dual inhibitors targeting hIDO1 and/or hTDO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of Ag on the Magnetic Anisotropy of Fe{sub 3}O{sub 4} Nanocomposites

In this work, the thermal decomposition method is used to obtain Fe{sub 3}O{sub 4}-Ag nanocomposites. The weight losses observed in the thermogravimetric measurements are used to estimate the amount of organic mass present in the samples. Fourier-transform infrared (FTIR) spectra show characteristic absorption peaks of the stretching vibration of the Fe-O and C-H groups. Samples are characterized structurally and morphologically by measurements of X-ray diffraction (XRD) and transmission electronic microscopy (TEM), respectively. The XRD patterns indicate the formation of a cubic phase with spinel crystallographic structure. Particles sizes analysis estimated by Scherrer’s equation for Fe{sub 3}O{sub 4} phase show that sizes are unaffected by the Ag-insertion. TEM images reveal that the nanoparticles have a spherical-like shape and a mean particles sizes ranging 3 < d < 4 nm. The best fits of zero-field-cooling and field-cooling (ZFC/FC) curves allow us to state that the magnetic anisotropy constant decreasing as a function of Ag concentration.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of Initial Structure on Performance of High-Entropy Oxide Anodes for Li-Ion Batteries

Two different high-entropy oxide materials were synthesized and studied as Li-ion battery anodes. The two materials have the same active metal constituents but different inactive elements which result in different initial crystalline structures: rock salt for (MgFeCoNiZn)O and spinel for (TiFeCoNiZn)3O4. Local structural studies of the metal elements in these two materials over extended electrochemical cycling reveal that the redox processes responsible for the electrode capacity are independent of the initial crystallographic structure and that the capacity is solely dependent on the initial random distribution of the metal atoms and the amount of active metals in the starting material.

25 ENERGY STORAGE↗

Evaluating Mineral Lattices as Evolutionary Proxies for Metalloprotein Evolution

Protein coordinated iron-sulfur clusters drive electron flow within metabolic pathways for organisms throughout the tree of life. It is not known how iron-sulfur clusters were first incorporated into proteins. Structural analogies to iron-sulfde minerals present on early Earth, suggest a connection in the evolution of both proteins and minerals. The availability of large protein and mineral crystallographic structure data sets, provides an opportunity to explore co-evolution of proteins and minerals on a large-scale using informatics approaches. However, quantitative comparisons are confounded by the infnite, repeating nature of the mineral lattice, in contrast to metal clusters in proteins, which are fnite in size. We address this problem using the Niggli reduction to transform a mineral lattice to a fnite, unique structure that when translated reproduces the crystal lattice. Protein and reduced mineral structures were represented as quotient graphs with the edges and nodes corresponding to bonds and atoms, respectively. We developed a graph theory-based method to calculate the maximum common connected edge subgraph (MCCES) between mineral and protein quotient graphs. MCCES can accommodate differences in structural volumes and easily allows additional chemical criteria to be considered when calculating similarity. To account for graph size differences, we use the Tversky similarity index. Using consistent criteria, we found little similarity between putative ancient iron-sulfur protein clusters and iron-sulfur mineral lattices, suggesting these metal sites are not as evolutionarily connected as once thought. We discuss possible evolutionary implications of these findings in addition to suggesting an alternative proxy, mineral surfaces, for better understanding the coevolution of the geosphere and biosphere

Kenneth N. McGuinness↗