Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Influence of copper content on the high temperature tensile and low cycle fatigue behavior of cast Al-Cu-Mn-Zr alloys

The relationship between low cycle fatigue (LCF) and monotonic tensile fracture strain was investigated for cast Al-Cu-Mn-Zr alloys containing 6 and 9 wt% Cu at 250 °C. The 9% Cu alloy consisted of larger size and volume fraction of brittle intermetallic grain boundary particles that fractured during tensile tests to reduce the fracture strain by 50% compared to the 6% Cu alloy. We found that LCF life was similar between the two alloys and weakly influenced by the particles. LCF life and fracture strain were poorly correlated due to the dominant influence of particles on monotonic tensile crack but not on fatigue crack.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermoelectric properties of BiSbTe-type alloys prepared by chill-casting and cryo-milling

The thermoelectric properties of Bi x Sb 1-x Te 3 processed through milling have been extensively studied with varied results that needs to be rationalized. Since cryo-milling is a relatively cleaner milling process compared to other milling processes, in this study we explore this technique to reduce the particle size prior to compaction to get an insight into the thermoelectric properties. We first report the results of cryomilled BiSbTe 3 compacted by spark plasmas sintering (SPS) process and show that milling leads to a change in transport behavior from ‘p’ to ‘n’ type similar to that reported for Bi 2 Te 3 . It is shown that the defects induced by milling is responsible for this change in materials behavior. We further study the effect of change in Bi to Sb ratio and excess tellurium on the thermoelectric properties when processed through cryo-milling as well as casting using a chilled copper block. Excess tellurium leads to a microstructure containing a fraction of layered eutectic that gets further fragmented during cryo-milling. Although the Seebeck coefficient does not change significantly, reflecting the cleanliness of the process, the thermal conductivity changes during hot compaction leading to an improvement of ZT. However, a comparison of all the reported results does not reveal any systematics in thermoelectric properties reflecting the difficulties with these materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Surface grain refinement of casting A380 aluminum alloy by ultrasonic-assisted surface mechanical grinding treatment

A novel surface processing technique, ultrasonic-assisted surface mechnical grinding treatment (U-SMGT), was proposed and applied to modify the surface micriostructure of the casting aluminum alloy (A380). Comprehensive post-process chracterization techniques including 3D profilometry, optical microscope, scanning electric microscopy (SEM), and electron backscatter diffraction (EBSD) were carried out to investigate the surface morphology and microstructure of the processed region (PR). It was found that a surface layer of grain refinement with a thickness of about 50 µm was formed. In the as-received base material (BM), large clusters of dendritic eutectic phase with a size of approximately 20 µm were isolated by α-Al matrix. Nano-indentation tests showed that hardness of the eutectic and α-Al in the as-received BM was 2.15 GPa and 1.2 GPa respectively. After U-SMGT, the large dendritic eutectic phase was broken down into much fine particles with an average size of 0.57 µm. These fine particles were uniformly distributed into the α-Al matrix. Nano-indentation measurement exhibited a hardness of 2.27 GPa within the processed region. The overall high hardness in the processed region is a result of the pinning effect of uniformly distributed fine dendrites and grain refinement of Al-matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhanced toughness and tear resistance of thin-walled High-Pressure Die-Cast aluminum alloys through Friction stir processing

In this study, we investigate the toughness and resistance to tear of thin-wall high-pressure die-cast (HPDC) aluminum alloys in two different orientations following the implementation of friction stir processing (FSP). The FSP technique was applied to two different HPDC Al-Si alloys: the recyclable-grade, high iron, A380 alloy and the premium-quality, low iron, Aural-5 alloy. Our findings reveal significant tear resistance and strength enhancements for both alloys after FSP modification. Specifically, FSPed A380 alloy requires 126% higher energy to tear, and it has 49% higher tear strength than the HPDC counterpart. Similarly, the tear energy and tear strength of the Aural-5 alloy witness enhancements of 69% and 21%, respectively. In conclusion, these results highlight the potential of FSP as a viable method for augmenting the mechanical properties of HPDC aluminum alloys, thereby opening up new avenues for their utilization in diverse engineering applications for crack obstruction.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Friction stir processing: A thermomechanical processing tool for high pressure die cast Al-alloys for vehicle light-weighting

This study uses friction stir processing (FSP) for thermomechanical processing of high-pressure die-casting (HPDC) to modify microstructure and improve mechanical properties. FSP is carried out on two different HPDC aluminum alloys: (a) general-purpose, high-iron, HPDC A380 alloy and (b) premium quality, low-iron HPDC Aural-5 alloy in thin wall, flat plate geometry. Subsequent mechanical testing shows ~30 % and ~65 % enhancement in yield strength and tensile ductility. In addition, FSP leads to ~10 times improvement in fatigue life for A380 alloy and ~70 % improvement in fracture toughness for Aural-5 alloy. These findings emphasize the capability of FSP to modify the microstructure of HPDC Al-alloys-based structural components so that they can demonstrate a good combination of strength, ductility, fracture toughness, and high fatigue properties for long-term durability and reliability.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Friction stir processing on a strontium modified, thin-wall, vacuum-assisted high-pressure die-cast Aural-5 alloy to improve tensile and fatigue performance

Here, this study explores the application of friction stir processing (FSP) to enhance the material properties of Sr-modified Aural-5 alloy, with a focus on improved tensile and fatigue properties. Aural-5 is a well-known vacuum-assisted high-pressure die-cast (HPDC) Al-Si7-Mg alloy used in the automotive industry to reduce vehicle weight, enhance fuel efficiency, and lower carbon emissions. This alloy modifies its material chemistry with Sr for fine fibrous networks of eutectic silicon and manganese (Mn) to reduce die soldering. It has significantly less iron (Fe) content resulting in the elimination of detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. The initial microstructure of as-received HPDC Aural-5 exhibits shrinkage porosity in the middle section, a dendritic microstructure with fibrous Al-Si eutectic colonies, a shear-band structure beneath the die-wall, large dendritic externally solidified crystals (ESCs), needle-shaped Mg 2 Si phase and significant second-phase particulates. Some of those microstructural features, such as porosity, ESCs, needle-shaped Mg 2 Si phase, and large second-phase particles, serve as initiation sites for cracks under mechanical loading, resulting in adverse effects on tensile properties, particularly ductility. FSP effectively transforms the microstructure into a wrought configuration with uniform particle distribution by eliminating porosity and disintegrating dendrites, eutectic colonies, ESCs, second-phase particles, and shear-band structures. FSP-driven microstructure modification enhances yield strength and tensile ductility by ~30% and ~35%, respectively. The fatigue life of the material in a bending mode configuration (stress ratio R = 0.1) after FSP exhibits enhancements ranging from 2.0 to 3.9 times that of the original HPDC Aural-5 alloy, depending on the applied stress level.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Chlorination of HALEU regulus casting dross

A scoping study was performed for chlorinating dross formed during uranium casting operations. Here, the purpose is to minimize the losses of uranium to dross wastes. The dross is primarily a mixture of uranium metal and uranium oxide with a minor fraction of crucible and crucible coating materials. The reaction chemistries were performed in a carrier salt of LiCl-KCl eutectic at 500 °C. The addition of FeCl 2 chlorinated the uranium metal to UCl 3 , by reducing the FeCl 2 to iron metal. After the uranium metal was chlorinated, zirconium metal was added to the salt. The residual FeCl 2 chlorinated the zirconium metal to ZrCl 4 , by reducing the FeCl 2 to iron metal. In turn, the ZrCl 4 chlorinated the uranium oxide to UCl 3 , by converting the ZrCl 4 to zirconium oxide. The effectiveness of the chlorination reactions was qualitatively verified by cyclic voltammograms that indicated the presence or absence of FeCl 2 and UCl 3 in the salt.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Development and testing of coarse-grained models for ultrasonic simulations of cast austenitic stainless steel

Ultrasonic inspection of cast austenitic stainless steel (CASS) in the nuclear industry is particularly challenging because of sound field scatter and attenuation caused by the coarse-grained microstructure. Modeling and simulation are important tools in ultrasonic testing, as they can be used to help address key aspects of inspections, such as developing new probe designs, predicting inspection reliability, and testing phased-array focal laws. However, developing a useful and reliable CASS model is challenging due to the many grain interfaces and crystalline orientations that must be captured. We demonstrate a method of creating a realistic CASS model that is usable in CIVA, a commercially available modeling and simulation software platform. Using polished and chemically etched sections, we generate models of a coarse-grained equiaxed specimen and a columnar specimen. We also test an alternative method of generating a coarse-grained model using Voronoi regions. We qualitatively compare sound field scatter and quantitatively compare sound field attenuation and beam partitioning in simulated sound fields to those of laboratory-measured sound fields. Results show that the Voronoi models perform as well as or better than the models based on actual grain morphology. Here we also show that model-to-model randomness in Voronoi grain structure can impact the magnitude of a simulated echo response by a factor of two or more. Although CASS models are potentially a good depiction of reality for a given scenario, they should not be considered representative since CASS morphology can change significantly from specimen to specimen or within the same specimen.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Freeze Tape Casting Electrode with Bilayered Architecture for High-Performance Lithium-Ion Batteries

A facile freeze tape casting (FTC) strategy is utilized to prepare bilayered 4 mAh cm –2 high-loading LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathodes. The bottom layer is a conventional nonaqueous electrode, which has a dense structure for high-energy purposes. Further, the top layer is prepared by the proposed FTC, exhibiting a porous feature for high-power requirement. With the assistance of FTC, the bilayered electrodes successfully deliver enhanced rate and cyclic performance due to the improved lithium-ion diffusion kinetics and pathways. Therefore, the proposed FTC strategy and its delivered electrodes are promising for energy- and power-density lithium-ion batteries, potentially enlightening the research and development of lithium-ion battery manufacturing.

25 ENERGY STORAGE↗
DOE OSTI2024

Cast Alumina-Forming Austenitic Stainless Steels for High Temperature Heat Treatment Furnace Rolls

Alloy developers worldwide have struggled to create creep-resistant alumina-forming, iron-based austenitic stainless steels for use as high-temperature structural alloys, but with limited success in balancing alloy cost, oxidation, and creep resistance. Here, this article describes the research and development of a novel cast alumina-forming austenitic stainless steel. This work won the prestigious Engineering Materials Achievement Award presented at IMAT 2023 in Detroit.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ink Casting and 3D‐Extrusion Printing of Yb 14 MnSb 11 for High‐Temperature Thermoelectric Material

Abstract Complex shapes are created from Yb 14 MnSb 11 , a high‐temperature thermoelectric Zintl phase, via a two‐step process: i) layer‐by‐layer 3D‐extrusion of ink containing partially‐reacted powders which are ball‐milled from a blend of Yb, MnSb, and Sb powders; ii) heat treatment to synthesize the ternary compound Yb 14 MnSb 11 and densify the extruded powders. A high phase purity for Yb 14 MnSb 11 (83–94%) is achieved in both cast and 3D‐extruded ink specimens via a solid‐state reaction between Yb, MnSb, and Yb 4 Sb 3 during reactive sintering. Pressure‐free sintering at temperatures of 1200–1400 °C densifies the powders to 82% relative density but can also induce the decomposition of the Yb 14 MnSb 11 phase due to Yb sublimation. A process window with optimized sintering temperature and time is identified, achieving both low porosity and high phase purity and reaching a maximum zT = 0.61 at 1000 °C, about half of the maximum zT value for bulk Yb 14 MnSb 11 made via conventional processes (pressure sintering of precursor powders). The present approach – direct ink writing of ball‐milled powders, combined with reactive sintering – is a scalable and affordable method to fabricate thermoelectric legs with intricate 3D shapes, for enhanced performances in high‐temperature thermoelectric applications.

Chen, Ming [Department of Materials Science &amp, ↗
DOE OSTI2023

Shear Assisted Processing and Extrusion of Unhomogenized Aluminum Alloy 6063 Castings with High Iron Content

Shear Assisted Processing and Extrusion (ShAPE) was used to fabricate aluminum 6063 tubing directly from secondary scrap. Trimmings from an automotive manufacturing facility were cast into billets spiked with iron (0.3 wt% Fe) to explore the tolerance of ShAPE to Fe contamination. Billets were extruded in the unhomogenized condition to form tubing with an outer diameter of 12 mm and wall thickness of 2 mm. Tensile properties reached 0.2% YS = 206 MPa, UTS = 238 MPa, and U.E. = 16.3% in the T6 temper. Performance exceeds the ASTM minimum standard and is on par with ASM typical values for conventional extrusion of primary aluminum billets in the fully homogenized condition. Microstructural characterization shows extensive refinement of grain size along with dispersion and refinement of Fe-Al-Si intermetallic phases. This study suggests that ShAPE extrusion may offer a lower carbon manufacturing pathway through direct recycling of secondary aluminum scrap and elimination of the billet homogenization step.

solid phase processing, AA 6063, extrusion, Shear ↗
DOE OSTI2023

Synthesis and characteristics of porous ceramic tubes: a comparison of centrifugal casting and cold isostatic pressing methods

Short porous ceramic tubes in small quantities are needed for membrane-related research and development efforts and can be synthesized by centrifugal casting (CC) or cold isostatic pressing (CIP) methods. Here, this work evaluates the characteristics of porous ceramic tubes prepared by both methods and provides a strategy for selecting the proper method for ceramic tube fabrication, depending on its application. Samarium-doped ceria (SDC) with an average crystallite size of 10 nm was synthesized by a citrate method and used to make porous SDC tubes by the CC and CIP methods under different conditions. Porous SDC tubes were prepared from an aqueous suspension of the SDC powder with polyvinyl alcohol (PVA) using a cylindrical metallic mold, centrifugated at 4000–6000 rpm, followed by sintering in 1200–1500 °C. SDC tubes were also made by the CIP method from the SDC powder placed inside a cylindrical rubber bag followed by isostatic compression at 1379 bar. The pore structure of the SDC tubes was characterized by helium permeation and liquid nitrogen Archimedes method. Due to high compression pressure giving a low porosity green tube, the CIP method with lower sintering temperature produces SDC tubes with much lower porosity and average pore size and similar tortuosity compared to the CC methods. The CIP method should be used to prepare low porosity or dense ceramic tubes, and the CC method should be used for preparing high-porosity ceramic tubes or tubes with pore gradient tube wall.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Combining Deep Learning and scatterControl for High-Throughput X-ray CT Based Non-Destructive Characterization of Large-Scale Casted Metallic Components

X-ray computed tomography (XCT) is essential for nondestructive evaluation and quality control of large-scale metal components. XCT imaging, however, faces significant challenges from metal artifacts, particularly those caused by Compton scattering, which degrade image quality and obscure critical details. Hardware-based solutions (e.g. scatterControl) offer advancements by intercepting scattered photons and reducing artifacts, but they can be time-consuming and require additional processing. Here, we propose modifying and leveraging a novel deep learning (DL) framework, Simurgh, to enhance and accelerate scatter correction in XCT. By combining scatterControl with DL-based artifact removal, we demonstrate significant reduction in scan time while producing high-quality reconstructions. Through extensive evaluation on industrial XCT data, we show that our methods reduce scan time by up to more than 10 x while preserving flaw detectability. Quantitative analysis across multiple segmentation techniques confirms that Simurgh-based reconstructions consistently outperform traditional Feldkamp-Davis-Kress, model-based iterative reconstruction, and commercial DL models in both pixel-level and task-specific evaluations, enabling scalable, high-throughput XCT workflows for characterization of large scale components in applications such as casting and metal additive manufacturing.

Complex metal parts↗
DOE OSTI2024

Design Solutes to Achieve Columnar-to-Equiaxed Transition and Grain Refinement in Cast Multi-principal-element Alloys

The multi-principal-element alloys (MPEAs), also referred to as high-entropy alloys (HEAs), have attracted extensive attention during the last decade and a half due to their unique and excellent properties. However, many MPEAs show coarse and anisotropic columnar grains in the as-cast state. While constitutional supercooling (CS)-driven parameters have been widely used to evaluate and predict the effect of solutes on columnar-to-equiaxed transition (CET) and grain refinement of diluted binary alloys, similar studies are lacking on MPEAs. Due to the multiple solute elements (solutes) and their high concentrations, the CS-driven parameters for MPEAs are different from those proposed for diluted binary alloys. Here, we derived the CS-driven parameters, including undercooling parameter and growth restriction factor, for MPEAs based on their physical significances, with the help of calculated phase diagrams. The calculated CS-driven parameters were then used to predict the effect of a solute on CET and grain refinement in NiCoFeCr MPEAs. Additional alloying solutes Nb, Ti, and V in the NiCoFeCr MPEA were also evaluated for their different CS-driven characteristics. In this study, the grain size of the as-solidified microstructures of NiCoFeCr with and without Nb, Ti, and V were compared and interpreted with the predicted tendency of the CS-driven parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Manufacturing Processes for Permanent Magnets: Part I—Sintering and Casting

Abstract Permanent magnets (PMs) produce magnetic fields and maintain the field even in the presence of an opposing magnetic field. Electrical machines using permanent magnets are more efficient than those without. Currently, all known strong magnets contain rare earth (RE) elements, and they are core components of a wide range of applications including electric vehicles and wind turbines. RE elements such as Nd and Dy have become critical materials due to the growing demand and constrained supply. Improving the manufacturing process is effective in mitigating the RE criticality issue by reducing waste and improving parts consistency. In this article, the state of the industry for PM is reviewed in detail considering both the technical and economic drivers. The importance of RE elements is discussed along with their economic importance to green energy. The conventional sintering and casting manufacturing processes for commercial magnets, including Nd-Fe-B, Sm-Co, Alnico, and ferrite, are described in detail.

36 MATERIALS SCIENCE↗
DOE OSTI2021

From casting to 3D printing geopolymers: A proof of concept

The objective of this paper is to define a mix design strategy allowing the implementation of geopolymer in powder bed 3D printing. In a selective binder approach, an aluminosilicate powder bed is activated through the deposit of an alkaline silicate solution. We first show that, in comparison to casting, this technology requires mastering the spreading of the liquid into the powder bed to ensure that the reaction takes place where it is needed. A series of experiments at the drop level, mimicking the 3D printing process, were performed to determine the printing solution composition for a given powder bed packing. We then highlight the relationship between the compressive strength of the printed geopolymer and the powder bed saturation, controlled by the printing parameters. Finally, SEM/EDX analysis confirm the formation of geopolymer with desired Si/Al and Na/Al ratios in the resulting printed material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Sulfate performance of blended cements (limestone and illite calcined clay) exposed to aggressive environment after casting

This paper evaluates how early aggressive exposure affects the sulfate resistance of blended cements containing limestone filler and/or calcined clay. Mortar and cement paste specimens were elaborated with different combinations of limestone filler and two different illitic calcined clays and exposed to a sodium sulfate solution shortly after casting. Assessment of sulfate resistance was based on expansion, mass variation, and compressive strength. Microscale evolution and distribution were examined by mercury intrusion porosimetry, X-ray diffraction, and scanning electron microscopy with energy-dispersive spectrometry measurements. Results prove superior sulfate resistance of compositions with high calcined clay content over limestone filler addition. Furthermore, the results reported suggest that the pozzolanic reaction progresses enough to reduce the sulfate ingress even at early exposure conditions. Therefore, calcined clay replacement can still provide effective pore refinement to limit sulfate penetration, increase strength, and reduce available CH to limit expansive phase formation.

36 MATERIALS SCIENCE↗