Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “blanket design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Savannah River National Laboratory – General Fusion 2023 INFUSE Report (Rev.1)

This report describes the results from an INFUSE research project, where Savannah River National Laboratory (SRNL) in collaboration with General Fusion (GF) used process modeling to understand and optimize commercial power plant (CPP) fuel cycle designs based on parameters provided by GF. The study primarily focused on two candidate fuel cycles with different blanket materials, one with a lead lithium eutectic (LLE) blanket and the other with a pure lithium (Li) blanket. LLE benefits from a low melting point, favorable neutronics, and lower reactivity, but liquid lithium has the potential for higher tritium breeding ratios (TBR) and does not poison the plasma as a high Z contaminant. It was found that the main differences between LLE and Li designs are the extraction technologies required to remove tritium from the blanket and the amount of tritium and its distribution within the facility. More than 80% of the in-process tritium inventory for the LLE design is contained in the isotope separation system, while for the Li design, over 60% of the in-process tritium inventory is contained within the blanket material. This is due to significant tritium retention by Li. For the Li blanket, the burden of tritium processing rests on the blanket extraction technology rather than the traditional exhaust processing route. Thus, the blanket extraction technology is a main driver of tritium inventory in the Li system and determines the subsequent interface with the tritium processing plant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Tritium Breeding Ratio Evaluation of Solid Breeder Concepts for the FESS-FNSF

This paper presents a parametric study of the Fusion Energy System Studies-Fusion Nuclear Science Facility’s (FNSF’s) tritium breeding performance for several solid breeder concepts, neutron multiplying materials, and blanket materials, assuming volume fractions based on the most recent FNSF design as a realistically representative fusion facility. In this study, we initially surveyed the tritium breeding ratio (TBR) of several solid breeder concepts by employing a simplified but efficient one-dimensional (1-D) infinite cylinder reduced-order model (ROM). Parametric studies were performed with the ROMs for the full range of breeder-to-multiplier ratios to identify the optimum mixture compositions for each breeder type that would lead to a maximum TBR. These optimized breeder-multiplier combinations were then homogenized with FNSF blanket component materials to estimate their impacts on the TBR. Subsequently, as a validation step for the optimal designs, TBR calculations were performed using a more realistic modified 1-D ROM with inner and outer breeding regions, as well as with a fully detailed 22.5-deg three-dimensional (3-D) sector of the FNSF to assess the impact of geometry details on the TBR. The differences between the two 1-D models were negligible, while the ROMs were able to correctly predict trends and identify the maximum and minimum TBR cases, as well as show consistent biases relative to the results produced by the full 3-D, 22.5-deg sector for specific breeder/multiplier combinations. Solid breeder concepts such as Li 2 O, Li 4 SiO 4 , and Li 8 ZrO 6 outperformed all others in this study in terms of TBR performance when combined with all the neutron multiplier materials selected. Here, an underlying goal of this study was to develop and improve rapid and reliable ROMs to aid designers during parametric optimizations of highly complex and computationally expensive fusion models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1975

Dewar technology study

The development of a Dewar system for handling liquid helium under weightless conditions is described. Porous plug designs for the prevention of superfluid creep out of the dewar through the vent line were evaluated. For the purpose of designing a neck to provide a transition from the cold cavity to the outside, the loads carried by the neck and equipment supports were studied. Temperature, pressure, and mass flow instrumentation for monitoring Dewar performance were also evaluated. In addition, multilayer blankets consisting of aluminized Mylar separated by Dacron net sheets were designed to insulate the pressure vessel. The dewar system is suggested for use with the star tracking telescope aboard the relativity satellite.

Davis, W.↗
NASA NTRS1990

Development of a model of space station solar array

Space structures, such as the space station solar arrays, must be extremely lightweight, flexible structures. Accurate prediction of the natural frequencies and mode shapes is essential for determining the structural adequacy of components, and designing a control system. The tension preload in the blanket of photovoltaic solar collectors, and the free/free boundary conditions of a structure in space, causes serious reservations on the use of standard finite element techniques of solution. In particular, a phenomena known as grounding, or false stiffening, of the stiffness matrix occurs during rigid body rotation. The grounding phenomena is examined in detail. Numerous stiffness matrices developed by others are examined for rigid body rotation capability, and found lacking. Various techniques are used for developing new stiffness matrices from the rigorous solutions of the differential equations, including the solution of the directed force problem. A new directed force stiffness matrix developed by the author provides all the rigid body capabilities for the beam in space.

Bosela, Paul A.↗
NASA NTRS2003

Development of a Thin Film Solar Cell Interconnect for the Powersphere Concept

Progressive development of microsatellite technologies has resulted in increased demand for lightweight electrical power subsystems including solar arrays. The use of thin film photovoltaics has been recognized as a key solution to meet the power needs. The lightweight cells can generate sufficient power and still meet critical mass requirements. Commercially available solar cells produced on lightweight substrates are being studied as an option to fulfill the power needs. The commercially available solar cells are relatively inexpensive and have a high payoff potential. Commercially available thin film solar cells are primarily being produced for terrestrial applications. The need to convert the solar cell from a terrestrial to a space compatible application is the primary challenge. Solar cell contacts, grids and interconnects need to be designed to be atomic oxygen resistant and withstand rapid thermal cycling environments. A mechanically robust solar cell interconnect is also required in order to withstand handling during fabrication and survive during launch. The need to produce the solar cell interconnects has been identified as a primary goal of the Powersphere program and is the topic of this paper. Details of the trade study leading to the final design involving the solar cell wrap around contact, flex blanket, welding process, and frame will be presented at the conference.

Simburger, Edward J.↗
NASA NTRSDate not supplied

Novel Deployable Sunshade for a Formation-Flying Telescope

- Deployable sunshade is based on folding paper party decoration. - Cellular structure creates strong, rigid form. - Instead of folding flat, the cellular fan is wrapped around a central hollow core to accommodate a focusing optic. - Imbedded spring ribs deploy the cellular fan into a large disk. - Shade is constructed of thermal blanket materials and is sewn together rather than glued. - Design bears some resemblance to JPL starshade, but is a much simpler design - JPL design includes pantograph-like mechanical structure and motors to drive deployment.

Anne-Marie Novo-Gradac↗
NASA NTRS2011

JPL Thermal Design Modeling Philosophy and NASA-STD-7009 Standard for Models and Simulations - A Case Study

The Standard JPL thermal engineering practice prescribes worst-case methodologies for design. In this process, environmental and key uncertain thermal parameters (e.g., thermal blanket performance, interface conductance, optical properties) are stacked in a worst case fashion to yield the most hot- or cold-biased temperature. Thus, these simulations would represent the upper and lower bounds. This, effectively, represents JPL thermal design margin philosophy. Uncertainty in the margins and the absolute temperatures is usually estimated by sensitivity analyses and/or by comparing the worst-case results with "expected" results. Applicability of the analytical model for specific design purposes along with any temperature requirement violations are documented in peer and project design review material. In 2008, NASA released NASA-STD-7009, Standard for Models and Simulations. The scope of this standard covers the development and maintenance of models, the operation of simulations, the analysis of the results, training, recommended practices, the assessment of the Modeling and Simulation (M&S) credibility, and the reporting of the M&S results. The Mars Exploration Rover (MER) project thermal control system M&S activity was chosen as a case study determining whether JPL practice is in line with the standard and to identify areas of non-compliance. This paper summarizes the results and makes recommendations regarding the application of this standard to JPL thermal M&S practices.

thermal blanket performance↗
NASA NTRS1976

Mechanical design

Design concepts for a 1000 mw thermal stationary power plant employing the UF6 fueled gas core breeder reactor are examined. Three design combinations-gaseous UF6 core with a solid matrix blanket, gaseous UF6 core with a liquid blanket, and gaseous UF6 core with a circulating blanket were considered. Results show the gaseous UF6 core with a circulating blanket was best suited to the power plant concept.

Source record↗
NASA NTRS2007

Thermal Performance Testing of Cryogenic Insulation Systems

Efficient methods for characterizing thermal performance of materials under cryogenic and vacuum conditions have been developed. These methods provide thermal conductivity data on materials under actual-use conditions and are complementary to established methods. The actual-use environment of full temperature difference in combination with vacuum-pressure is essential for understanding insulation system performance. Test articles include solids, foams, powders, layered blankets, composite panels, and other materials. Test methodology and apparatus design for several insulation test cryostats are discussed. The measurement principle is liquid nitrogen boil-off calorimetry. Heat flux capability ranges from approximately 0.5 to 500 watts per square meter; corresponding apparent thermal conductivity values range from below 0.01 up to about 60 mW/m- K. Example data for different insulation materials are also presented. Upon further standardization work, these patented insulation test cryostats can be available to industry for a wide range of practical applications.

Fesmire, James E.↗
NASA NTRS1979

Weight optimization of ultra large space structures

The paper describes the optimization of a solar power satellite structure for minimum mass and system cost. The solar power satellite is an ultra large low frequency and lightly damped space structure; derivation of its structural design requirements required accommodation of gravity gradient torques which impose primary loads, life up to 100 years in the rigorous geosynchronous orbit radiation environment, and prevention of continuous wave motion in a solar array blanket suspended from a huge, lightly damped structure subject to periodic excitations. The satellite structural design required a parametric study of structural configurations and consideration of the fabrication and assembly techniques, which resulted in a final structure which met all requirements at a structural mass fraction of 10%.

Reinert, R. P.↗
NASA NTRS1977

Conceptual approach study of a 200 watt per kilogram solar array, phase 1

Two alternative designs were studied; one a retractable rollout design and the other a nonretractable foldout configuration. An end of life (EOL) power for either design of 0.79 beginning of life (BOL) is predicted based on one solar flare during a 3 year interplanetary mission. Both array configurations incorporate the features of flexible substrates and cover sheets. A power capacity of 10 kilowatt is achieved in a blanket area of 76 sq m with an area utilization factor of 0.8. A single array consists of two identical solar cell blankets deployed concurrently by a single, coilable longeron boom. An out of plane angle of 8-1/4 deg is maintained between the two blankets so that the inherent inplane stiffness of the blankets may be used to obtain out of plane stiffness. This V-stiffened design results in a 67% reduction in the stiffness requirement for the boom. Since boom mass scales with stiffness, a lower requirement on boom stiffness results in a lower mass for the boom. These solar arrays are designed to be compatible with the shuttle launch environment and shuttle cargo bay size limitations.

Rayl, G. J.↗
DOE OSTI2023

Fully Implicit Conjugate Heat Transfer Analysis of the ARC-Class Vacuum Vessel

The coupled simulation of fusion reactor blankets including neutronics, thermal-hydraulics and thermo-mechanics is expected to speed up the design cycle of fusion reactor design concepts. In this work we demonstrate tight implicit coupling of conjugate heat transfer using the open-source Computational Fluid Dynamics software OpenFOAM for thermo-fluid mechanics and Diablo for thermo-solid mechanics. The heat transfer analysis is augmented by volumetric energy deposition from neutronic calculations using the Monte Carlo N-particle code on both solid and fluid parts of the vacuum vessel. An additional heat flux is imposed on the first wall estimated from the design power of the reactor. The tight coupling is realized through the open-source coupling library, preCICE, and tested on the vacuum vessel of the affordable, robust, compact reactor design by Commonwealth Fusion Systems. The features of the coupling and the influence of different coupling parameters such as coupling schemes, acceleration techniques and convergence criterion are discussed. The coupled simulation results are compared to a thermal-hydraulics simulation which includes only the fluid domains (the liquid immersion molten salt blanket and cooling channel) to demonstrate usefulness of a coupled simulation. Further analysis is performed to identify regions of hot spots for subsequent design improvement. This introduces the outline for integrating conjugate electromagnetics and fluid/solid mechanics (e.g., allow for deformation of the cooling channel walls) with our present approach for future analysis.

Sircar, Arpan↗
NASA NTRS2006

Thermal Challenge for Sun-Viewing Instruments on Solar Probe 3 R(sub s) from Sun

The Solar Probe science team at NASA GSFC is considering enhance science observations by adding the nadir viewing Plasma Spectrometer instrument and using heat shields to protect the Plasma Wave antennas to permit full extension at 3 R. The electrostatic mirror of the Plasma Spectrometer is thermally protected from the Sun by a miniature sunshield that consists of two carbon-carbon composite layers, and a much smaller carbon-carbon heat shield. The sun-viewing surface of the miniature sunshield has an Al2O3 thin film coating. The slope of the sunshield is minimized to the smallest possible extent so that it can still accommodate the elliptical electrostatic mirror. Two small MLI flaps minimize the heat radiation from the Plasma Spectrometer to the spacecraft bus. This design meets the thermal requirements. Each of the four Plasma Wave wire antennas is 5 m long, and thermally protected from the Sun by a sunshield. The sunshield consists of two carbon-carbon composite sheets. One sheet views the Sun, and one does not. The slope of most of the sun-viewing sheet is 23deg with the nadir axis. For mechanical reason, it gradually increases to 37.5deg at the tip. The exterior of the sun viewing surfaces has a thin film of Al2O3. The exterior of the shaded sheets has a thin film of vapor deposited rhodium. It minimizes the heat radiation to the spacecraft bus. A high temperature MLI blanket between the carbon-carbon sheets radiatively isolates them. The thermal design meets the temperature requirements, but exceeds the 20 W limit of heat radiation to the spacecraft bus by 20 W. Thermal options to reduce the heat radiation include reducing the alpha to epsilon ratio of the Al2O3 thin film and reducing the number of antennas to three. Testing in 2006 includes thermal model validation and materials testing. High temperature ovens and a high light intensity Vortex Lamp will be used.

Choi, Michael K.↗
NASA NTRS1991

Design, optimization, and analysis of a self-deploying PV tent array

A tent shaped PV array was designed and the design was optimized for maximum specific power. In order to minimize output power variation a tent angle of 60 deg was chosen. Based on the chosen tent angle an array structure was designed. The design considerations were minimal deployment time, high reliability, and small stowage volume. To meet these considerations the array was chosen to be self-deployable, form a compact storage configuration, using a passive pressurized gas deployment mechanism. Each structural component of the design was analyzed to determine the size necessary to withstand the various forces to which it would be subjected. Through this analysis the component weights were determined. An optimization was performed to determine the array dimensions and blanket geometry which produce the maximum specific power for a given PV blanket. This optimization was performed for both lunar and Martian environmental conditions. Other factors such as PV blanket types, structural material, and wind velocity (for Mars array), were varied to determine what influence they had on the design point. The performance specifications for the array at both locations and with each type of PV blanket were determined. These specifications were calculated using the Arimid fiber composite as the structural material. The four PV blanket types considered were silicon, GaAs/Ge, GaAsCLEFT, and amorphous silicon. The specifications used for each blanket represented either present day or near term technology. For both the Moon and Mars the amorphous silicon arrays produced the highest specific power.

Collozza, Anthony J.↗
NASA NTRS1973

Feasibility study of a 110 watt per kilogram lightweight solar array system

The feasibility of a 10,000 watt solar array panel which has a minimum power-to-mass ratio of 110 watt/kg is discussed. The application of this ultralightweight solar array to three possible missions was investigated. With the interplanetary mission as a baseline, the constraining requirements for a geosynchronous mission and for a manned space station mission are presented. A review of existing lightweight solar array system concepts revealed that changes in the system approach are necessary to achieve the specified 110 watt/kg goal. A comprehensive review of existing component technology is presented in the areas of thin solar cells, solar cell covers, welded interconnectors, substrates and deployable booms. Advances in the state-of-the-art of solar cell and deployable boom technology were investigated. System level trade studies required to select the optimum boom bending stiffness, system aspect ratio, bus voltage level, and solar cell circuit arrangement are reported. Design analysis tasks included the thermal analysis of the solar cell blanket, thermal stress analysis of the solar cell interconnectors/substrate, and the thermostructural loading of the deployed boom.

Shepard, N. F.↗
NASA NTRS1992

Grounding of space structures

Space structures, such as the Space Station solar arrays, must be extremely light-weight, flexible structures. Accurate prediction of the natural frequencies and mode shapes is essential for determining the structural adequacy of components, and designing a controls system. The tension pre-load in the 'blanket' of photovoltaic solar collectors, and the free/free boundary conditions of a structure in space, causes serious reservations on the use of standard finite element techniques of solution. In particular, a phenomenon known as 'grounding', or false stiffening, of the stiffness matrix occurs during rigid body rotation. This paper examines the grounding phenomenon in detail. Numerous stiffness matrices developed by others are examined for rigid body rotation capability, and found lacking. A force imbalance inherent in the formulations examined is the likely cause of the grounding problem, suggesting the need for a directed force formulation.

Bosela, P. A.↗
NASA NTRS1992

A new pre-loaded beam geometric stiffness matrix with full rigid body capabilities

Space structures, such as the Space Station solar arrays, must be extremely light-weight, flexible structures. Accurate prediction of the natural frequencies and mode shapes is essential for determining the structural adequacy of components, and designing a controls system. The tension pre-load in the 'blanket' of photovoltaic solar collectors, and the free/free boundary conditions of a structure in space, causes serious reservations on the use of standard finite element techniques of solution. In particular, a phenomenon known as 'grounding', or false stiffening, of the stiffness matrix occurs during rigid body rotation. The authors have previously shown that the grounding phenomenon is caused by a lack of rigid body rotational capability, and is typical in beam geometric stiffness matrices formulated by others, including those which contain higher order effects. The cause of the problem was identified as the force imbalance inherent in the formulations. In this paper, the authors develop a beam geometric stiffness matrix for a directed force problem, and show that the resultant global stiffness matrix contains complete rigid body mode capabilities, and performs very well in the diagonalization methodology customarily used in dynamic analysis.

Bosela, P. A.↗
NASA NTRS1994

Composite flexible blanket insulation

An improved composite flexible blanket insulation is presented comprising top silicon carbide having an interlock design, wherein the reflective shield is composed of single or double aluminized polyimide and wherein the polyimide film has a honeycomb pattern.

Kourtides, Demetrius A.↗