SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In an extension of "thermal lens" effect to new applications and better resolution, two laser beams combine to rapidly measure thermal diffusivity and other molecular dynamic properties. New double-beam technique handles very small samples unlike classical techniques for measuring diffusivity. It can be used for measurements on samples undergoing stress, making it applicable to data collection for structural engineering.
The primary objectives of this study were to obtain the necessary data and develop a calculation procedure that would facilitate predicting the atmospheric-helium contribution to the drag of a satellite having a predominantly convex exterior. Molecular-beam techniques were used to measure, for several incidence angles, the spatial and energy distributions of 7000 m/s helium atoms scattered from a 6061-T6 aluminum plate and an anodized 1235-0 aluminum surface. From these measured distributions, tangential and normal momentum accommodation coefficients were calculated as functions of incidence angle. Using these calculated accommodation coefficients, one can predict drag coefficients for satellites having predominantly convex exteriors. For spherical satellites, drag coefficients of 2.64 and 2.62 were predicted for the subject surfaces.
The Ribbon-to-Ribbon (RTR) process for growth of silicon ribbon is described. This process involves the fabrication of a microcrystalline ribbon of silicon and subsequent grain size enhancement through a laser recrystallization process. The microribbon is obtained from a Thermal Expansion Shear Separation (TESS) process which allows a CVD layer of silicon to be separated from a temporary molybdenum substrate. Efforts to achieve increased solar cell efficiencies and higher area production rates have been problematical. Furnaces, which are necessary for thermal stress control, have been shown to contribute contamination to substrates resulting in degraded efficiencies. Recent results with a new furnace design indicate efficiencies in excess of 9% will be routine. Limitations to area throughput arise due to fundamental linear velocity limitations and width limitations necessary to prevent the occurrence of thermal buckling. Calculations are reported which show the influence of thermal profile on buckling tendencies, and a proposed electron beam technique is considered which promises high throughput with minimal buckling.
Studies of the structure, stability, electronic properties, and formation kinetics of small clusters were reviewed which provide information useful in furthering understanding of nucleation processes, liquid state properties, and the nature of surfaces. Using mass spectrometric coupled with various high pressure ion clustering and Stark effect-molecular beam techniques, the details of the primary clustering steps leading to the nucleation of bulk liquid from the vapor were and obtained by direct observation results are presented.
Absolute charge-transfer cross sections for collisions of protons with hydrogen and deuterium atoms have been measured within the energy range 0.1 to 150 eV using the merging-beams technique. The results are in excellent agreement with a fully quantum-mechanical treatment of this reaction. Earlier measurements which extended down to about 10 eV lie somewhat above the present values.
The present conference on heterogeneous atmospheric chemistry considers such topics concerning clusters, particles and microparticles as common problems in nucleation and growth, chemical kinetics, and catalysis, chemical reactions with aerosols, electron beam studies of natural and anthropogenic microparticles, and structural studies employing molecular beam techniques, as well as such gas-solid interaction topics as photoassisted reactions, catalyzed photolysis, and heterogeneous catalysis. Also discussed are sulfur dioxide absorption, oxidation, and oxidation inhibition in falling drops, sulfur dioxide/water equilibria, the evidence for heterogeneous catalysis in the atmosphere, the importance of heterogeneous processes to tropospheric chemistry, soot-catalyzed atmospheric reactions, and the concentrations and mechanisms of formation of sulfate in the atmospheric boundary layer.
Lower temperatures result in higher purity and fewer equipment problems. In cluster-beam deposition, clusters of atoms formed by adiabatic expansion nozzle and with proper nozzle design, expanding vapor cools sufficiently to become supersaturated and form clusters of material deposited. Clusters are ionized and accelerated in electric field and then impacted on substrate where films form. Improved cluster-beam technique useful for deposition of refractory metals.
Robotic welding controlled by reliable, relatively-noise-free optoelectronic unit. Bounding off meniscus of pool of molten metal, laser beam impinges on position-sensitive photodetector. Beam diameter adjusted for width of weld. Optical filters screen out light from arc. Made from small, low-cost components and utilizing optical fibers to conduct signals, system immune to electromagnetic interference common in industrial environments. Aimed for automatic welders, robot welders in particular and also adaptable to other types of welding, including tungsten/inert-gas, laser, and electron-beam techniques.
Studies were performed to synthesize new ether modified, flexibilized aromatic diamine hardeners for curing epoxy resins. The effect of moisture absorption on the glass transition temperatures of a tetraglycidyl epoxy, MY 720, cured with flexibilized hardeners and a conventional aromatic diamine was studied. Unidirectional composites, using epoxy-sized Celion 6000 graphite fiber as the reinforcement, were fabricated. The room temperature and 300 F mechanical properties of the composites, before and after moisture exposure, were determined. The Mode I interlaminar fracture toughness of the composites was characterized using a double cantilever beam technique to calculate the critical strain energy release rate.
The present conference on advancements in IR-sensitive materials and detector technologies employing them gives attention to thermal detectors, focal plane array processing detectors, novel detector designs, general properties of IR optics materials, and preparation methods for such materials. Specific topics encompass the fabrication of InSb MIS structures prepared by photochemical vapor deposition, IR heterodyne detectors employing cadmium mercury telluride, low microphony pyroelectric arrays, IR detection based on minority carrier extrusion, longwave reststrahl in IR crystals, and molecular beam techniques for optical thin film fabrication.
A fiber-optic temperature sensor is described, which uses a small silicon beamsplitter whose splitting ratio varies as a function of temperature. A four-beam technique is used to measure the sensor's temperature-indicating splitting ratio. This referencing method provides a measurement that is largely independent of the transmission properties of the sensor's optical fiber link. A significant advantage of this sensor, relative to other fiber-optic sensors, is its high stability, which permits the fiber-optic components to be readily substituted, thereby simplifying the sensor's installation and maintenance.
Bulk chemical compositions of matrix material were determined in eleven Antarctic CM chondrites and five non-Antarctic CM and CI chondrites, using microprobe defocused-beam technique. The results, along with previously published data, are used to provide mass balance constraints on the relative proportions of intergrown and intermixed phyllosilicate phases in carbonaceous chondrite matrices. In terms of Fe, Si, and Mg, the CM matrix bulk compositions plot within a triangle defined by the compositions of PCP (a mixture of 25 percent tochilinite and 75 percent cronstedtite), Mg-rich serpentine, and Fe-rich serpentine. Results indicate differing amounts of PCP and serpentines in individual CM matrices. The discrepancies found between predicted and measured S and Ni values require additional sulfide phases. CI matrices were found to contain little, if any, PCP; they consist mostly of serpentine and montmorillonite.
A crossed-beam technique was used to measure absolute differential cross sections for the vibrational excitation of water-vapor molecules. The energy and angular range were from 2.2 to 20 eV and from 30 to 150 deg. Vibrational-excitation cross sections were determined for the bending (010) and stretching (100 and 001) modes of the electronic ground state. It is shown that the integral cross sections are generally larger than those of Seng and Linder (1976) by 10-20 percent for both the bending and stretching modes. It is noted that the results obtained are of interest in connection with the theoretical modeling of cometary ionospheres.
A fiber-optic temperature sensor is described that uses a small silicon beamsplitter whose splitting ratio varies as a function of temperature. A four-beam technique is used to measure the sensor's temperature-indicating splitting ratio. This referencing method provides a measurement that is largely independent of the transmission properties of the sensor's optical fiber link. A significant advantage of this sensor, relative to other fiber-optic sensors, is its high stability, which permits the fiber-optic components to be readily substituted, thereby simplifying the sensor's installation and maintenance.
In any mechanical or engineering system where contacting surfaces are in relative motion, adhesion, wear, and friction affect reliability and performance. With the advancement of space age transportation systems, the tribological requirements have dramatically increased. This is due to the optimized design, precision tolerance requirements, and high reliability expected for solid lubricating films in order to withstand hostile operating conditions (vacuum, high-low temperatures, high loads, and space radiation). For these problem areas the ion-assisted deposition/modification processes (plasma-based and ion beam techniques) offer the greatest potential for the synthesis of thin films and the tailoring of adherence and chemical and structural properties for optimized tribological performance. The present practices and new approaches of applying soft solid lubricant and hard wear resistant films to engineering substrates are reviewed. The ion bombardment treatments have increased film adherence, lowered friction coefficients, and enhanced wear life of the solid lubricating films such as the dichalcogenides (MoS2) and the soft metals (Au, Ag, Pb). Currently, sputtering is the preferred method of applying MoS2 films; and ion plating, the soft metallic films. Ultralow friction coefficients (less than 0.01) were achieved with sputtered MoS2. Further, new diamond-like carbon and BN lubricating films are being developed by using the ion assisted deposition techniques.
The following subject areas are covered: General Reflector Antenna Systems Program version 7(GRASP7); Multiple Reflector Analysis Program for Cylindrical Antennas (MRAPCA); Tri-Reflector 2D Synthesis Code (TRTDS); a geometrical optics and a physical optics synthesis techniques; beam scanning reflector, the type 2 and 6 reflectors, spherical reflector, and multiple reflector imaging systems; and radiometric array design.
Additional calculations which characterize potential energy sources (PESs) for the excited 3A-double-prime state, for a bound 2(2A-prime) state, for HN2(+), and for the Rydberg states associated with HN2(+). It is anticipated that these excited state PESs will be important in interpreting and designing experiments to characterize the ground state HN2 species via neutralized ion beam techniques.
An introduction is given to a system for particle analysis by mass spectrometry (PAMS) which employs particle-beam techniques to measure mass spectra on a continuous real-time basis. The system is applied to particles of both organic and inorganic compounds, and the measurements give the chemical characteristics of particles in mixtures and indicate source apportionment. The PAMS system can be used for process control and studying heterogeneous/catalytic reactions in particles, and can be fitted to study the real-time attributes of PAMS.