Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “battery failure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Air Force nickel-hydrogen test program

After using all the instrumentation that is available on a nickel hydrogen battery it will be subjected to the same low earth orbit cycles experienced by the sixty amphere hour nickel cadmium batteries now being flown on some low earth orbit missions. The objective of the test is to demonstrate real differences between the two batteries. In order to simulate flight conditions, the thermal environment and criteria for charge control will vary. The depth of discharge will be increased and testing will continue until some failures or some degradation or spread between cell performances are revealed. Different charge control modes are being considered in order to demonstrate a reasonable life for the nickel hydrogen battery.

Gandel, M. G.↗
NASA NTRS1993

NASA Lewis advanced IPV nickel-hydrogen technology

Individual pressure vessel (IPV) nickel-hydrogen technology was advanced at NASA Lewis and under Lewis contracts. Some of the advancements are as follows: to use 26 percent potassium hydroxide electrolyte to improve cycle life and performance, to modify the state of the art cell design to eliminate identified failure modes and further improve cycle life, and to develop a lightweight nickel electrode to reduce battery mass, hence reduce launch and/or increase satellite payload. A breakthrough in the LEO cycle life of individual pressure vessel nickel-hydrogen battery cells was reported. The cycle life of boiler plate cells containing 26 percent KOH electrolyte was about 40,000 accelerated LEO cycles at 80 percent DOD compared to 3,500 cycles for cells containing 31 percent KOH. Results of the boiler plate cell tests have been validated at NWSC, Crane, Indiana. Forty-eight ampere-hour flight cells containing 26 and 31 percent KOH have undergone real time LEO cycle life testing at an 80 percent DOD, 10 C. The three cells containing 26 percent KOH failed on the average at cycle 19,500. The three cells containing 31 percent KOH failed on the average at cycle 6,400. Validation testing of NASA Lewis 125 Ah advanced design IPV nickel-hydrogen flight cells is also being conducted at NWSC, Crane, Indiana under a NASA Lewis contract. This consists of characterization, storage, and cycle life testing. There was no capacity degradation after 52 days of storage with the cells in the discharged state, on open circuit, 0 C, and a hydrogen pressure of 14.5 psia. The catalyzed wall wick cells have been cycled for over 22,694 cycles with no cell failures in the continuing test. All three of the non-catalyzed wall wick cells failed (cycles 9,588; 13,900; and 20,575). Cycle life test results of the Fibrex nickel electrode has demonstrated the feasibility of an improved nickel electrode giving a higher specific energy nickel-hydrogen cell. A nickel-hydrogen boiler plate cell using an 80 mil thick, 90 percent porous Fibrex nickel electrode has been cycled for 10,000 cycles at 40 percent DOD.

Smithrick, John J.↗
NASA NTRS2020

Verification of Prognostic Algorithms to Predict Remaining Flying Time for Electric Unmanned Vehicles

This paper addresses the problem of building trust in the online prediction of a eUAV’s remaining available flying time powered by lithium-ion polymer batteries. A series of ground tests are described that make use of an electric unmanned aerial vehicle (eUAV) to verify the performance of remaining flying time predictions. The algorithm verification procedure described is implemented on a fully functional vehicle that is restrained to a platform for repeated run-to-functional-failure (charge depletion) experiments. The vehicle under test is commanded to follow a predefined propeller RPM profile in order to create battery demand profiles similar to those expected during flight. The eUAV is repeatedly operated until the charge stored in powertrain batteries falls below a specified limit threshold. The time at which the limit threshold on battery charge is crossed is then used to measure the accuracy of the remaining flying time prediction. In our earlier work battery aging was not included. In this work we take into account aging of the batteries where the parameters were updated to make predictions. Accuracy requirements are considered for an alarm that warns operators when remaining flying time is estimated to fall below the specified limit threshold.

Edward F. Hogge↗
NASA NTRS1980

Coatings for hybrid microcircuits

Silicone or parylene coatings protect circuits from damage by battery of military standard tests. PIND (Partical Impact Noise Detection) test proved unreliable in predicting failure for either coated or uncoated circuits.

Kinser, D. L.↗
NASA NTRS2009

Apollo Lunar Module Electrical Power System Overview

Objectives include: a) Describe LM Electrical System original specifications; b) Describe the decision to change from fuel cells to batteries and other changes; c) Describe the Electrical system; and d) Describe the Apollo 13 failure from the LM perspective.

Interbartolo, Michael↗
NASA NTRS1994

Primary battery design and safety guidelines handbook

This handbook provides engineers and safety personnel with guidelines for the safe design or selection and use of primary batteries in spaceflight programs. Types of primary batteries described are silver oxide zinc alkaline, carbon-zinc, zinc-air alkaline, manganese dioxide-zionc alkaline, mercuric oxide-zinc alkaline, and lithium anode cells. Along with typical applications, the discussions of the individual battery types include electrochemistry, construction, capacities and configurations, and appropriate safety measures. A chapter on general battery safety covers hazard sources and controls applicable to all battery types. Guidelines are given for qualification and acceptance testing that should precede space applications. Permissible failure levels for NASA applications are discussed.

Bragg, Bobby J.↗
NASA NTRSDate not supplied

Simulation Studies for an Urban Air Mobility Aircraft using Hardware-In-Loop Experiments

Urban Air Mobility seeks to transport passengers, deliver cargo, and provide emergency medical transportation in major metropolitan areas. This will be accomplished with distributed electric powered vertical takeoff and landing aircraft vehicles. The low specific energy of the current generation lithium-ion battery packs limit the operational range of the electric aircraft. Limited range impacts safety by reducing the amount of time available for analyzing the potential impact of errors and failures and responding to them, and for flying to an alternative landing area or returning to the base. It is therefore critical to understand the impact of flight and environmental conditions on the onboard lithium-ion battery pack’s health. With this as the motivation, the procedure for evaluating the performance of battery packs in a laboratory setting and the results obtained using this procedure on battery packs subject to power draw characteristics of a simulated flight of a NASA conceptual quadrotor aircraft model are described. The fully charged battery is allowed to discharge at specific C-rates based on the power draw profile during the experiment, and the current and voltages are recorded as a function of time. Observed results under different operating conditions and mission profiles are discussed.

UAM↗
NASA NTRS1996

Hypervelocity Impact Testing of Nickel Hydrogen Battery Cells

Nickel-Hydrogen (Ni/H2) battery cells have been used on several satellites and are planned for use on the International Space Station. In January 1992, the NASA Lewis Research Center (LeRC) conducted hypervelocity impact testing on Ni/H2 cells to characterize their failure modes. The cell's outer construction was a 24 mil-thick Inconel 718 pressure vessel. A sheet of 1.27 cm thick honeycomb was placed in front of the battery cells during testing to simulate the on-orbit box enclosure. Testing was conducted at the NASA White Sands Test Facility (WSTF). The hypervelocity gun used was a 7.6 mm (0.30 caliber) two-stage light gas gun. Test were performed at speeds of 3, 6, and 7 km/sec using aluminum 2017 spherical particles of either 4.8 or 6.4 mm diameter as the projectile. The battery cells were electrically charged to about 75 percent of capacity, then back-filled with hydrogen gas to 900 psi simulating the full charge condition. High speed film at 10,000 frames/sec was taken of the impacts. Impacts in the dome area (top) and the electrode area (middle) of the battery cells were investigated. Five tests on battery cells were performed. The results revealed that in all of the test conditions investigated, the battery cells simply vented their hydrogen gas and some electrolyte, but did not burst or generate any large debris fragments.

Frate, David T.↗
NASA NTRS2010

Optical Structural Health Monitoring Device

This non-destructive, optical fatigue detection and monitoring system relies on a small and unobtrusive light-scattering sensor that is installed on a component at the beginning of its life in order to periodically scan the component in situ. The method involves using a laser beam to scan the surface of the monitored component. The device scans a laser spot over a metal surface to which it is attached. As the laser beam scans the surface, disruptions in the surface cause increases in scattered light intensity. As the disruptions in the surface grow, they will cause the light to scatter more. Over time, the scattering intensities over the scanned line can be compared to detect changes in the metal surface to find cracks, crack precursors, or corrosion. This periodic monitoring of the surface can be used to indicate the degree of fatigue damage on a component and allow one to predict the remaining life and/or incipient mechanical failure of the monitored component. This wireless, compact device can operate for long periods under its own battery power and could one day use harvested power. The prototype device uses the popular open-source TinyOS operating system on an off-the-shelf Mica2 sensor mote, which allows wireless command and control through dynamically reconfigurable multi-node sensor networks. The small size and long life of this device could make it possible for the nodes to be installed and left in place over the course of years, and with wireless communication, data can be extracted from the nodes by operators without physical access to the devices. While a prototype has been demonstrated at the time of this reporting, further work is required in the system s development to take this technology into the field, especially to improve its power management and ruggedness. It should be possible to reduce the size and sensitivity as well. Establishment of better prognostic methods based on these data is also needed. The increase of surface roughness with fatigue is closely connected to the microstructure of the metal, and ongoing research is seeking to connect this observed evidence of the fatigue state with microstructural theories of fatigue evolution to allow more accurate prognosis of remaining component life. Plans are also being discussed for flight testing, perhaps on NASA s SOFIA platform.

Buckner, Benjamin D.↗
NASA NTRS2004

Reconditioning of Batteries on the International Space Station

Primary source of electric power for the International Space Station (ISS) is the photovoltaic module (PVM). At assembly complete stage, the ISS will be served by 4 PVMs. Each PVM contains two independent power channels such that one failure will result in loss of only one power channel. During early stages of assembly, the ISS is served by only one PVM designated as P6. Solar arrays are used to convert solar flux into electrical power. Nickel hydrogen batteries are used to store electrical power for use during periods when the solar input is not adequate to support channel loads. Batteries are operated per established procedures that ensure that they are maintained within specified temperature limits, charge current is controlled to conform to a specified charge profile, and battery voltages are maintained within specified limits. Both power channels on the PVM P6 have been operating flawlessly since December 2000 with 100 percent power availability. All components, including batteries, are monitored regularly to ensure that they are operating within specified limits and to trend their wear out and age effects. The paper briefly describes the battery trend data. Batteries have started to show some effects of aging and a battery reconditioning procedure is being evaluated at this time. Reconditioning is expected to reduce cell voltage divergence and provide data that can be used to update the state of charge (SOC) computation in the software to account for battery age. During reconditioning, each battery, one at a time, will be discharged per a specified procedure and then returned to a full state of charge. The paper describes the reconditioning procedure and the expected benefits. The reconditioning procedures have been thoroughly coordinated by all affected technical teams and approved by all required boards. The reconditioning is tentatively scheduled for September 2004.

Hajela, Gyan↗
NASA NTRS1976

Design of the High Energy Astronomy Observatory /HEAO/ power subsystem

Observatory power is generated by a partially deployable solar array which is modularized to facilitate adaptation to three missions having different power requirements. Three nickel-cadmium batteries are controlled independently from dedicated modular chargers to increase subsystem adaptability and decrease sensitivity to temperature differences between batteries. Battery level redundancy is employed, enabling mission completion with two of three battery/charger combinations operational. Bus voltage limiting is accomplished by a modularized shunt regulator which can survive any single part failure and meet all mission requirements. Relatively low shunt electronics power dissipation internal to the observatory is achieved by sequenced operation of linear shunt segments which are coupled to a large area resistive shunt radiator. Summaries of solar array, battery and subsystem breadboard test results are provided.

Reppucci, G. M.↗
NASA NTRS1987

Automation - Changes in cognitive demands and mental workload

The effect of partial automation on mental workloads in man/machine tasks is investigated experimentally. Subjective workload measures are obtained from six subjects after performance of a task battery comprising two manual (flight-path control, FC, and target acquisition, TA) tasks and one decisionmaking (engine failure, EF) task; the FC task was performed in both a fully manual (altitude and lateral control) mode and in a semiautomated mode (autmatic latitude control). The performance results and subjective evaluations are presented in graphs and characterized in detail. The automation is shown to improve objective performance and lower subjective workload significantly in the combined FC/TA task, but not in the FC task alone or in the FC/EF task.

Tsang, Pamela S.↗
NASA NTRS2009

Power Goals for NASA's Exploration Program

Exciting Future Programs ahead for NASA. Power is needed for all Exploration vehicles and for the missions. For long term missions as in Lunar and Mars programs, safe, high energy/ultra high energy batteries are required. Safety is top priority for human-rated missions. Two-fault tolerance to catastrophic failures is required for human-rated safety To meet power safety goals -inherent cell safety may be required; it can lessen complexity of external protective electronics and prevents dependency on hardware that may also have limitations. Inherent cell safety will eliminate the need to carry out screening of all cells (X-rays, vibration, etc.)

Jeevarajan, Judith A.↗
NASA NTRS2003

COTS Li-Ion Cells in High Voltage Batteries

Testing at NASA JSC and COMDEV shows that Commercial Off the Shelf (COTS) Li Ion cells can not be used in high voltage batteries safely without considering the voltage stresses that may be put on the protective devices in them during failure modes.

Davies, Francis↗
NASA NTRS1975

Availability of a communications satellite - Requirement and feasibility

An estimated 45 communications satellites will be in geostationary orbit in the 1980s. Based on past history, half of the subsystem failures will be due to design failures. Methods now used to achieve present availabilities are summarized in this paper. To increase the availability of a single satellite to 99.99%, new techniques are needed; several possibilities are suggested herein. New developments, including nickel-hydrogen batteries, magnetic bearings, and solid-state amplifiers, are possible solutions to long standing problem areas in communications satellites. Launching a satellite two or three years before the system is needed is one way to reduce design failures in subsequent satellites. Diversity of manufacture can be used to obtain the maximum advantage from redundant elements. Finally, unmanned module exchange at geostationary orbit has been shown to be technically feasible.

Gordon, G. D.↗