Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “austenite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Study of the Long-Term Strength of Neutron-Irradiated Austenitic and Ferrite-Martensite Steel

The results of a study of the long-term strength of austenitic and ferrite-martensite steel after irradiation in the BR-10, BOR-60, BN-350, and BN-600 reactors are presented. It is shown that irradiation of austenitic-class steel (EI-847, 0Kh18N10T, and ChS-68) greatly reduces the time to failure and the plasticity. This behavior of austenitic steel is associated with the phenomenon of high-temperature radiation embrittlement. Neutron irradiation does not degrade the long-term mechanical characteristics of ferrite-martensite steel, which remain either at the level of the unirradiated material (EP-823, 05Kh12N2M steels) or surpass it (EP-450 steel).

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

ON MEASUREMENT OF CARBON CONTENT IN RETAINED AUSTENITE IN A NANOSTRUCTURED BAINITIC STEEL

In this study, the carbon content of retained austenite in a nanostructured bainitic steel was measured by atom probe tomography and compared with data derived from the austenite lattice parameter determined by X-ray diffraction. The results provide new evidence about the heterogeneous distribution of carbon in austenite, a fundamental issue controlling ductility in this type of microstructure.

36 MATERIALS SCIENCE↗

Load partitioning and strain-induced martensite formation during tensile loading of a metastable austenitic stainless steel.

In-situ high-energy X-ray diffraction and material modeling are used to investigate the strain-rate dependence of the strain-induced martensitic transformation and the stress partitioning between austenite and {alpha}{prime} martensite in a metastable austenitic stainless steel during tensile loading. Moderate changes of the strain rate alter the strain-induced martensitic transformation, with a significantly lower {alpha}{prime} martensite fraction observed at fracture for a strain rate of 10{sup -2} s{sup -1}, as compared to 10{sup -3} s{sup -1}. This strain-rate sensitivity is attributed to the adiabatic heating of the samples and is found to be well predicted by the combination of an extended Olson-Cohen strain-induced martensite model and finite-element simulations for the evolving temperature distribution in the samples. In addition, the strain-rate sensitivity affects the deformation behavior of the steel. The {alpha}{prime} martensite transformation at high strains provides local strengthening and extends the time to neck formation. This reinforcement is witnessed by a load transfer from austenite to {alpha}{prime} martensite during loading.

36 MATERIALS SCIENCE↗

In Situ Local Measurement of Austenite Mechanical Stability and Transformation Behavior in Third-Generation Advanced High-Strength Steels

Austenite mechanical stability, i.e., retained austenite volume fraction (RAVF) variation with strain, and transformation behavior were investigated for two third generation advanced high strength steels (3GAHSS) under quasi-static uniaxial tension: a 1200 grade, two-phase medium Mn (10 wt%) TRIP steel, and a 980 grade, three-phase TRIP steel produced with a quenching and partitioning heat treatment. The Mn (10 wt%) TRIP steel deforms inhomogeneously via propagative instabilities (Lüders and Portevin Le Châtelier-like bands) while the 980 grade TRIP steel deforms homogenously up to necking. The dramatically different deformation behaviors of these steels required the development of a new in-situ experimental technique that couples volumetric synchrotron X-ray diffraction measurement of RAVF with surface strain measurement using stereo digital image correlation (DIC) over the beam impingement area. Measurement results with the new technique are compared with those from a more conventional approach wherein strains are measured over the entire gauge region while RAVF measurement is the same as that in the new technique. A determination is made as to the appropriateness of the different measurement techniques in measuring the transformation behaviors for steels with homogeneous and inhomogeneous deformation behaviors. Here, extension of the new in-situ technique to the measurement of austenite transformation under different deformation modes and to higher strain rates is discussed.

36 MATERIALS SCIENCE↗

Effects of Heat Treatment on Phase Transformation and Corrosion Resistance of Boride Layer on Austenitic Stainless Steel AISI 304

The austenitic stainless steel AISI 304 was thermochemically surface treated using a powder-packed boronizing process at a temperature of 950 °C for about 4 hours. Double-phase boride layer (FeB and Fe{sub 2}B) was detected and then investigated for the corrosion resistance compared with the untreated one. Heat treatment was performed at a temperature range of 800 to 900 °C for 2 hours on the boronized austenitic stainless steel AISI 304 to diminish the double-phase boride layer. Afterward, corrosion tests were performed to clarify the effects of heat treatment as well as phase transformation on the corrosion resistance of the boronized austenitic stainless steel AISI 304. The results of this study showed that the formation of single-phase Fe{sub 2}B layer offers the best corrosion resistance.

36 MATERIALS SCIENCE↗

Effect of Zr Microalloying on Austenite Grain Size of Low-Carbon Steels

The effect of microalloying addition of Zr on the characteristics of inclusions and prior austenite grain sizes following a quench heat treatment has been investigated for two custom-made steels. The average size of particles in the Zr-containing steel is found to be the same as the Zr-free steel (0.49 μm). However, the number of smaller particles in the Zr-containing steel is much higher than the Zr-free steel. The inclusions in the Zr-containing steel are composed of ZrO{sub 2}-TiN-MnS, and inclusions in the Zr-free steel are consisted of TiOx-Ti(C,N). The average prior austenite grain size of the Zr-containing steel is consistently smaller than that of the Zr-free steel, due to a large number of fine oxide inclusions and Ti(C,N) precipitates, working to pin the austenite grain boundaries at temperatures up to 1673 K (1400 °C). The grain refinement mechanisms by inclusions through the addition of Zr are discussed via thermodynamic and kinetic calculations.

36 MATERIALS SCIENCE↗

Development of cast alumina-forming austenitic stainless steels

Cast Fe-Ni-Cr chromia-forming austenitic stainless steels with Ni levels up to 45 wt. % are used at high temperatures in a wide range of industrial applications that demand microstructural stability, corrosion resistance, and creep strength. Although alumina scales offer better corrosion protection at these temperatures, designing cast austenitic alloys that form a stable alumina scale and achieve creep strength comparable to existing cast chromia-forming alloys is challenging. This work outlines the development of cast Fe-Ni-Cr-Al austenitic stainless steels containing about 25 wt. % Ni with good creep strength and the ability to form a protective alumina scale for use at temperatures up to 800 C - 850 C in H 2 O-, S-, and C- containing environments. Creep properties of the best alloy were comparable to that of HK-type cast chromia-forming alloy along with improved oxidation resistance typical of alumina-forming alloys. Lastly, challenges in the design of cast alloys and a potential path to increasing the temperature capability are discussed.

36 MATERIALS SCIENCE↗

Hydrogen effects on the deformation and slip localization in a single crystal austenitic stainless steel

Hydrogen is known to embrittle austenitic stainless steels, which are widely used in high-pressure hydrogen storage and delivery systems, but the mechanisms that lead to such material degradation are still being elucidated. The current work investigates the deformation behavior of single crystal austenitic stainless steel 316L through combined uniaxial tensile testing, characterization and atomistic simulations. Thermally precharged hydrogen is shown to increase the critical resolved shear stress (CRSS) without previously reported deviations from Schmid’s law. Molecular dynamics simulations further expose the statistical nature of the hydrogen and vacancy contributions to the CRSS in the presence of alloying. Slip distribution quantification over large in-plane distances (> 1 mm), achieved via atomic force microscopy (AFM), highlights the role of hydrogen increasing the degree of slip localization in both single and multiple slip configurations. The most active slip bands accumulate significantly more deformation in hydrogen precharged specimens, with potential implications for damage nucleation. For $\langle$110$\rangle$ tensile loading, slip localization further enhances the activity of secondary slip, increases the density of geometrically necessary dislocations and leads to a distinct lattice rotation behavior compared to hydrogen-free specimens, as evidenced by electron backscatter diffraction (EBSD) maps. Finally, the results of this study provide a more comprehensive picture of the deformation aspect of hydrogen embrittlement in austenitic stainless steels.

36 MATERIALS SCIENCE↗

Additive manufacturing of functionally graded transition joints between ferritic and austenitic alloys

Dissimilar metal joints between ferritic and austenitic alloys are susceptible to premature failure due to diffusive carbon loss from the ferritic alloy driven by abrupt changes in carbon chemical potential. Compositional grading of transition joints fabricated using laser-based directed energy deposition additive manufacturing offers a means for limiting carbon diffusion. In this report we fabricate functionally graded transition joints between a ferritic and austenitic alloy, characterize spatial variations of chemical composition, microstructure and hardness, and test their effectiveness to limit carbon loss from the ferritic alloy. Microstructural studies and carbon potential variations in the functionally graded material showed that the length of the joints can be shorter, and there is no benefit to continue compositional grading once the microstructure becomes fully austenitic. Since dissimilar joints have an expected lifetime of several decades, long service times were simulated through accelerated heat treatment experiments at elevated temperatures for both a dissimilar metal weld and a functionally graded transition joint. While the dissimilar weld showed pronounced carbon loss from the ferritic side, there was insignificant change in the carbon concentration profile in the functionally graded joint indicating effectiveness of the graded joints to perform under service conditions.

36 MATERIALS SCIENCE↗

Understanding failure in austenitic steels: Key considerations for molten salt storage in CSP applications

Owing to their excellent properties, austenitic stainless steels are extensively used in boilers, furnaces, molten salt tanks, and other applications that are subjected to extreme mechanical loads and high-temperature conditions. Their high corrosion and creep resistance make them suitable for high-temperature operating environments. Additionally, good fatigue resistance and favorable mechanical and visual properties are essential. However, the premature failure of several components at elevated temperatures has been previously reported. Although the failure analysis of components in service is complex, processes such as cold work and welding have been identified as contributing factors to the performance degradation of these steels. This study aims to analyze the various documented failure modes and mechanisms in austenitic steels, including creep, cracking, stress relaxation cracking, and fatigue, to better understand the multi-objective design requirements for these alloys as structural materials for high-temperature molten salt tanks in Concentrating Solar Power (CSP) plants. Stabilized austenitic grades, such as AISI 347H, demonstrate superior resistance to creep and corrosion-related degradation when compared to non-stabilized grades like AISI 316L at temperatures relevant to concentrated solar power (CSP) applications. In contrast, nickel-based alloys offer enhanced corrosion resistance, albeit at a higher cost. This review underscores that creep, stress relaxation cracking, and thermo-mechanical fatigue are the predominant long-term failure risks in CSP hot tanks.

14 SOLAR ENERGY↗

Effect of laser welding on deformation mechanisms in irradiated austenitic stainless steel

In this work, deformation mechanism of a laser weld on neutron irradiated AISI 304L stainless steel was studied by in-situ microcompression test at room temperature. The deformation-induced austenite-to-martensite phase transformation occurs in {101}-oriented grains in the irradiated base metal, while deformation twinning prevails in {101}-oriented grains in the weld heat affected zone (HAZ). A high number density of irradiation-induced voids in the base metal provide sufficient nucleation sites for the austenite-to-martensite phase transformation under compression at room temperature. A deformation map is established to predict critical twinning stress for face-centered cubic (fcc) metals and alloys. Our study suggests that irradiation can tailor the deformation-induced phase transformation in austenitic stainless steels.

36 MATERIALS SCIENCE↗

Retained austenite thermal stability in a nanostructured bainitic steel

The unique microstructure of nanostructured bainite consists of very slender bainitic ferrite plates and high carbon retained austenite films. As a consequence, the reported properties are opening a wide range of different commercial uses. However, bainitic transformation follows the T{sub 0} criteria, i.e. the incomplete reaction phenomena, which means that the microstructure is not thermodynamically stable because the bainitic transformation stops well before austenite reaches an equilibrium carbon level. This article aims to study the different microstructural changes taking place when nanostructured bainite is destabilized by austempering for times well in excess of that strictly necessary to end the transformation. Results indicate that while bainitic ferrite seems unaware of the extended heat treatment, retained austenite exhibits a more receptive behavior to it. - Highlights: • Nanostructured bainitic steel is not thermodynamically stable. • Extensive austempering in these microstructures has not been reported before. • Precipitation of cementite particles is unavoidable at longer austempering times. • TEM, FEG-SEM and XRD analysis were used for microstructural characterization.

36 MATERIALS SCIENCE↗

On the improvement of measurement accuracy of retained austenite in steel with X-ray diffraction

Highlights: • Improved procedure to determine austenite in steels with crystallographic texture • Extension to X-ray area detectors • Electropolishing is essential to get correct results. - Abstract: An improved measurement scheme for the determination of the retained austenite fraction with X-ray diffraction is extended to area detectors. The scheme reduces the error due to crystallographic texture in phase analysis of steel by averaging the results of diffraction patterns at different sample positions. The method is based on the standard ASTM E975, but it can be easily extended to other crystal structures, multi-phase materials or X-ray wavelengths. Phase transformation, induced by mechanical sample preparation, may lead to a significant reduction of the retained austenite fraction. Electropolishing before the measurement is beneficial to remove the layer affected by sample preparation.

36 MATERIALS SCIENCE↗

Characterization of martensite-austenite constituents and micro-hardness in intercritical reheated and coarse-grained heat affected zones of API X70 HSLA steel

Highlights: • The influence of cold wire addition to the tandem submerged arc welding process on the ICRCGHAZ is investigated. • Comprehensive characterization of the microstructure and micro-hardness in the ICRCGHAZ of a HSLA steel is performed. • A lower fraction of finely distributed M-A formed in the ICRCGHAZ of TSAW + cold wire steel, leading to lower micro-hardness. • The aspect ratio and inter-particle spacing of M-A constituents decreased in the ICRCGHAZ through cold wire addition. - Abstract: The thermal cycles that high strength low alloy (HSLA) low carbon steels experience during welding inevitably affect the microstructure and mechanical properties of the weld joints. It is generally agreed that the coarse-grained heat affected zone (CGHAZ) and the intercritical reheated coarse-grained heat affected zone (ICRCGHAZ) in one-pass and multi-pass welding, respectively, have the poorest microstructure and mechanical properties relative to the rest of the steel joint. The martensite-austenite (M-A) constituents formed in the HAZ regions predominantly govern property deterioration in the CGHAZ and the ICRCGHAZ by promoting the initiation and propagation of micro-cracks. However, the characteristics of the M-A constituents, i.e., fraction, size, shape and aspect ratio, are strongly affected by the welding heat input. Accordingly, in this study, the aim was to evaluate the influence of a cold wire addition in conventional tandem submerged arc welding (TSAW + cold-wire) on the microstructure and micro-hardness in the CGHAZ and ICRCGHAZ. Microstructural characterization showed that a lower fraction of finely distributed M-A constituents associated with smaller prior austenite grains (PAGs) formed in the CGHAZ of the steel welded by the TSAW + cold-wire process (CW-OD weld) relative to that welded by the conventional TSAW process (TW-OD weld). Furthermore, the fraction of M-A constituents in the ICRCGHAZ of the CW-OD weld was decreased. A higher fraction of slender shaped M-A constituents in the ICRCGHAZ of the TW-OD weld resulted in an increase in the micro-hardness. The microstructure and micro-hardness changes associated with cold wire addition were attributed to the lower welding heat input and, consequently, the faster cooling rate with a corresponding reduction in the retention time in the austenitic region and ferrite/austenite region in the CGHAZ and ICRCGHAZ regions, respectively.

36 MATERIALS SCIENCE↗

Isothermal annealing behaviour of nuclear grade 20Cr-25Ni austenitic stainless steel

Highlights: • At 930 °C recrystallisation of deformed 20/25 Nb steel is completed after 120 s. • Recrystallisation proceeds by strain induced boundary migration. • An increase of cube oriented grains at the expense of S oriented is observed. • The boundary migration induced the precipitation of niobium carbides. • The grain size is limited by the particle dispersion according to Zener pinning. - Abstract: We have performed an in-depth characterisation of the microstructure evolution of 20Cr-25Ni Nb-stabilised austenitic stainless steel during isothermal annealing at 930 °C using scanning and transmission electron microscopy. This steel grade is used as cladding material in advanced gas-cooled fission reactors, due to its resistance to thermal creep and water corrosion. The initial deformed microstructure undergoes recrystallisation via a strain-induced boundary migration mechanism, attaining a fully recrystallised microstructure after 120 s of annealing. The transition from low-to-high grain boundaries has already occurred after 15 s, together with an increase in the cube grain orientation at the expense of the S texture component. After 120 s, the grain boundary migration induces the formation of new fine Nb(C,N) particles, whereas the pre-existing particles become enriched in Ni and Si. The resulting particle population limits the grain growth in the austenitic matrix, based on the Zener pinning model, resulting in relatively small recrystallised austenite grains and a high density of high-angle and special coincidence-lattice-site grain boundaries, together with a large number of particle/matrix interfaces.

36 MATERIALS SCIENCE↗

Influence of carbon partitioning kinetics on final Austenite fraction during quenching and partitioning

The quenching and partitioning (Q&P) process is a two-stage heat-treatment procedure proposed for producing steel microstructures that contain carbon-enriched retained austenite. In Q&P processing, austenite stabilization is accomplished by carbon partitioning from supersaturated martensite. A quench temperature selection methodology was developed to predict an optimum process quench temperature; extension of this methodology to include carbon partitioning kinetics is developed here. Final austenite fraction is less sensitive to quench temperature than previously predicted, in agreement with experimental results.

36 MATERIALS SCIENCE↗

Development of a twin crystal membrane coupled conformable phased array for the inspection of austenitic welds

The inspection of welded austenitic stainless steel components can be challenging. Austenitic welds contain an anisotropic, inhomogeneous grain structure which causes attenuation, scattering and beam bending. The inspection of components where the weld cap has not been removed is even more difficult due to the irregularity of the surface geometry. A twin crystal membrane coupled device has now been produced containing two linear phased arrays positioned adjacent to one another within the same housing. The arrays are angled relative to one another so that the transducer provides a pseudo-focusing effect at a depth corresponding to the beam crossing point. This type of design is used to improve the signal to noise ratio of the defect response in comparison to simple linear phased array transducer designs and to remove an internal noise signal found in linear phased array devices. Experimental results obtained from the through weld inspection of an austenitic stainless steel component with an undressed weld cap using the twin crystal membrane device are presented. These results demonstrate that small lack of side wall fusion defects can be reliably detected in large complex structures.

42 ENGINEERING↗

Corrosion resistance of kolsterised austenitic 304 stainless steel

Austenitic stainless suffers from low wear resistance in applications where rubbing against other surfaces is encountered. This drawback can be overcome by surface treatment such as coating by hard materials. Other treatments such as carburization at relatively low temperature become applicable recently to improve hardness and wear resistance. Carburization heat treatment would only be justified if the corrosion resistance is unaffected. In this work samples of 304 stainless steels treated by colossal supersaturation case carburizing (known as Kolsterising) carried out by Bodycote Company was examined for pitting corrosion resistance at room temperature and at 50 °C. Comparison with results obtained for untreated samples in similar testing conditions show that there is no deterioration in the pitting resistance due to the Kolsterising heat treatment. X ray diffraction patterns obtained for Kolsterising sample showed that peaks correspond to the austenite phase has shifted to lower 2θ values compared with those of the untreated sample. The shift is an indication for expansion of austenite unit cells caused by saturation with diffusing carbon atoms. The XRD of Kolsterising samples also revealed additional peaks appeared in the patterns due to formation of carbides in the kolsterised layer. Examination of these additional peaks showed that these peaks are attributed to a type of carbide known as Hagg carbide Fe{sub 2}C{sub 5}. The absence of carbides that contain chromium means that no Cr depletion occurred in the layer and the corrosion properties are maintained. Surface hardness measurements showed large increase after Kolsterising heat treatment.

36 MATERIALS SCIENCE↗