SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Estimation of the time for steam generator trip due to cyber intrusions

The time required to trip a pressurized water reactor (PWR) by inserting malicious signals into its steam generator (SG) control system has been studied using the Generic PWR (GPWR) Simulator. A semi-analytical model is developed to approximately reproduce the simulator response and understand the dynamics of the control unit. A series of two proportional-integral controllers determines control action according to preset constants, the readings from the feedwater level sensor, and those from feedwater and steam flowrate transmitters. It is observed that the most important factor that determines whether a trip will occur is how much additional water is added to or withheld from the SG over time compared to normal operating conditions. In order to determine the effects of control action on the SG, changes in mass inventory are considered. This approach models the SG water level as a function of mass inventory and has a backward temporal memory. A Python interface is developed for the GPWR framework to automatically simulate different spoofing scenarios and post-process the related data. We observe that the trip times predominantly depend on flow mismatch and/or level errors. Controller parameters, including the integral time and gain constants, either speed up or slow down the rate of progression to a trip setpoint but do not cause a trip by themselves. The reactor can trip on a high-level signal when the reading crosses above 78%, increased from its reference level of 57%, or a low-level reading when it is below 25%. The present results show roughly how long the operators would have to respond to an attack, given a specific set of spoofing signals within the issue space analyzed. Furthermore, we have generated a simple surface by fitting a combination of exponential functions to the data obtained from the GPWR Simulator. In general, trips on a low level have been observed to occur faster than those on a high level.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

Aging of Concrete for the Evaluation of Repair Materials to Protect the Walls of the HCAEX Tunnel at Savannah River - 20301

H-Canyon, located in the Savannah River site, is a unique facility for chemical reprocessing of plutonium, highly-enriched uranium, and other radioactive materials. The exhaust gases of the H-Canyon are sent through the H-Canyon Exhaust (HCAEX) tunnel for contamination removal. Robotic inspections of the tunnel revealed significant degradation of the reinforced concrete structure that was associated with acid attack, and could compromise the structural stability of the tunnel. Thus, the identification and evaluation of potential repair materials that could be applied on the degraded walls to mitigate and prevent further degradation is of significant interest to the Department of Energy and the Savannah River representatives. This research effort has been divided into two phases: 1) Development and evaluation of aged concrete under accelerated aging conditions (which is the focus of this paper) and 2) Evaluation of potential repair materials applied on aged and non-aged concrete under simulated aggressive conditions. In order to develop and evaluate concrete samples exposed to accelerated aging conditions in simulated aggressive environments, a literature review of the HCAEX tunnel was conducted that included 1) characterization and extent of the concrete damage, 2) environmental conditions inside the tunnel and 3) primary deterioration mechanisms. In addition, potential coatings and/or repair materials for degraded concrete surfaces exposed to aggressive environments (primarily acidic) were selected from the literature review and the most common testing and measurements for evaluating acid attack phenomena, erosion, etc. were reviewed. From the literature review findings, a preliminary bench-scale test plan for the concrete aging was developed, including accelerated aging tests with aggressive conditions (acid fumes, humidity, etc.). Concrete samples were exposed to the aging accelerated conditions (e.g. immersion in acid solutions) and visual inspection, mass loss and pH change (acid solution) were recorded over time. Correlations between the visual inspection, mass loss and pH changes results and the aging time or the aging conditions were developed. Specimens submitted to the highest acid concentration showed the fastest and most intense degradation. The type of coarse aggregate (limestone) used for the concrete seemed to be the cause of the fastest aging observed, compared to the cement paste. The research findings created the foundation for the ongoing investigation, in which new concrete samples with a mix design similar to the HCAEX tunnel will be tested and will serve as the substrate for testing the selected coatings and /or repair materials. In this paper, the literature review and preliminary results from the aging tests are provided. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

Invited Review Paper in Commemoration of Over 50 Years of Oxidation of Metals: Addressing the Role of Water Vapor on Long-Term Stainless Steel Oxidation Behavior

In the past 20 years, it has become clear that the long-term exposure of chromia-forming austenitic stainless steels to air containing ~ 10 vol% water vapor at 650–800 °C significantly increases the Cr consumption rate compared to laboratory air. However, a similar acceleration does not occur in 100% steam because O 2 is not available to form volatile CrO 2 (OH) 2 . As the research has shown, this accelerated Cr loss is particularly important for thin-walled components like gas turbine recuperators. Typically, conventional austenitic stainless steels exhibit accelerated attack (i.e., rapid formation of Fe-rich oxide nodules), while higher alloyed steels resist this type of degradation until the alloy surface becomes Cr depleted. The development of strategies and solutions for this issue are reviewed. Model Fe–Cr–Ni alloys have been used to study composition effects on this behavior. For example, increasing the Mn content up to ~ 4 wt% was not beneficial, but increasing the Ni content improved oxidation resistance in this environment. However, at 650–700 °C even highly alloyed steels showed surface Cr depletion at alloy grain boundaries resulting in Fe-rich oxide nodule formation. The path forward for this issue will require more refined mechanistic understanding and increased used of modeling to develop better application-specific lifetime models to identify the most cost-effective alloy solutions.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Data from Reactive Species and Reaction Pathways for the Oxidative Cleavage of 4-Octene and Oleic Acid with H2O2 over Tungsten Oxide Catalysts

Oxidative cleavage of carbon–carbon double bonds (C═C) in alkenes and fatty acids produces aldehydes and acids valued as chemical intermediates. Solid tungsten oxide catalysts are low cost, nontoxic, and selective for the oxidative cleavage of C═C bonds with hydrogen peroxide (H2O2) and are, therefore, a promising option for continuous processes. Despite the relevance of these materials, the elementary steps involved and their sensitivity to the form of W sites present on surfaces have not been described. Here, we combine in situ spectroscopy and rate measurements to identify significant steps in the reaction and the reactive species present on the catalysts and examine differences between the kinetics of this reaction on isolated W atoms grafted to alumina and on those exposed on crystalline WO3 nanoparticles. Raman spectroscopy shows that W–peroxo complexes (W–(η2-O2)) formed from H2O2 react with alkenes in a kinetically relevant step to produce epoxides, which undergo hydrolysis at protic surface sites. Subsequently, the CH3CN solvent deprotonates diols to form alpha-hydroxy ketones that react to form aldehydes and water following nucleophilic attack of H2O2. Turnover rates for oxidative cleavage, determined by in situ site titrations, on WOx–Al2O3 are 75% greater than those on WO3 at standard conditions. These differences reflect the activation enthalpies (ΔH‡) for the oxidative cleavage of 4-octene that are much lower than those for the isolated WOx sites (36 ± 3 and 60 ± 6 kJ·mol–1 for WOx–Al2O3 and WO3, respectively) and correlate strongly with the difference between the enthalpies of adsorption for epoxyoctane (ΔHads,epox), which resembles the transition state for epoxidation. The WOx–Al2O3 catalysts mediate oxidative cleavage of oleic acid with H2O2 following a mechanism comparable to that for the oxidative cleavage of 4-octene. The WO3 materials, however, form only the epoxide and do not cleave the C–C bond or produce aldehydes and acids. These differences reflect the distinct site requirements for these reaction pathways and indicate that acid sites required for diol formation are strongly inhibited by oleic acids and epoxides on WO3 whereas the Al2O3 support provides sites competent for this reaction and increase the yield of the oxidative cleavage products.

Catalysis↗

DOE OSTI2022

Effect of Applied Stress on the Selective Oxidation of Alloy 600 Exposed to PWR Primary Water and Rhines Pack Environments

A mechanistic understanding of corrosion and oxidation processes is crucial to ensure long-term resistance to stress corrosion cracking of Ni-base structural alloys in pressurized water reactor (PWR) primary and secondary systems. Aqueous corrosion of Ni-base alloys under PWR primary water conditions was previously compared to gaseous oxidation with comparable oxygen potentials. However, those studies considered only stress-free conditions, which removes a critical parameter for understanding stress corrosion behaviors. A significant knowledge gap exists for the role of applied stresses on selective internal oxidation in gaseous environments. A micro-4-point-bend jig was designed to facilitate stress in a Rhines Pack set-up. Selective oxidation at different stress and strain conditions was investigated in a series of Rhines Pack experiments for Alloy 600. Focused ion beam milling enabled the extraction of site-specific specimens containing selected high-energy grain boundaries from tensile and compressive stress regions. Analytical transmission electron microscopy was employed to analyze the microstructure and chemical composition of the resulting oxides. Protective surface oxide films and selective intergranular oxides were observed at different conditions. The implications of these fundamental differences are discussed relative to intergranular attack and stress corrosion cracking mechanisms in PWR primary water.

stress, 4-point-bend, selective oxidation, Alloy 6↗

DOE OSTI2021

Effect of Fluoroethylene Carbonate Additives on the Initial Formation of the Solid Electrolyte Interphase on an Oxygen-Functionalized Graphitic Anode in Lithium-Ion Batteries

The formation of a solid electrolyte interphase (SEI) at the electrode/electrolyte interface substantially affects the stability and lifetime of lithium-ion batteries (LIBs). One of the methods to improve the lifetime of LIBs is by the inclusion of additive molecules to stabilize the SEI. To understand the effect of additive molecules on the initial stage of SEI formation, in this work we compare the decomposition and oligomerization reactions of a fluoroethylene carbonate (FEC) additive on a range of oxygen-functionalized graphitic anodes to those of an ethylene carbonate (EC) organic electrolyte. A series of density functional theory (DFT) calculations augmented by ab initio molecular dynamics (AIMD) simulations reveal that EC decomposition on an oxygen-functionalized graphitic ($11\bar{2}0$) edge facet through a nucleophilic attack on an ethylene carbon site (C E ) of an EC molecule (S2 mechanism) is spontaneous during the initial charging process of LIBs. However, decomposition of EC through a nucleophilic attack on a carbonyl carbon (C C ) site (S1 mechanism) results in alkoxide species regeneration that is responsible for continual oligomerization along the graphitic surface. In contrast, FEC prefers to decompose through an S1 pathway, which does not promote alkoxide regeneration. Including FEC as an additive is thus able to suppress alkoxide regeneration and results in a smaller and thinner SEI layer that is more flexible toward lithium intercalation during the charging/discharging process. In addition, we find that the presence of different oxygen functional groups at the surface of graphite dictates the oligomerization products and the LiF formation mechanism in the SEI.

25 ENERGY STORAGE↗

DOE OSTI2021

Reactive Species and Reaction Pathways for the Oxidative Cleavage of 4-Octene and Oleic Acid with H 2 O 2 over Tungsten Oxide Catalysts

The oxidative cleavage of carbon-carbon double bonds (C=C) in alkenes and fatty acids produces aldehydes and acids valued as chemical intermediates. Solid tungsten oxide catalysts are low cost, non-toxic, and selective for the oxidative cleavage of C=C bonds with hydrogen peroxide (H 2 O 2 ) and are, therefore, a promising option for continuous processes. Despite the relevance of these materials, the elementary steps involved and their sensitivity to the form of W sites present on surfaces have not been described. In this work, we combine in situ spectroscopy and rate measurements to identify significant steps in the reaction, the reactive species present on catalysts, and examine differences between the kinetics of this reaction on isolated W atoms grafted to alumina and on those exposed on crystalline WO 3 nanoparticles. Raman spectroscopy shows that W-peroxo complexes (W-(η 2 -O 2 ) formed from H 2 O 2 ) react in a kinetically relevant step to produce epoxides, which undergo hydrolysis at protic surface sites. Subsequently, the CH 3 CN solvent deprotonates diols to form alpha hydroxy ketones that react to form aldehydes and water following nucleophilic attack of H 2 O 2 . Turnover rates for oxidative cleavage, determined by in situ site titrations, on WO x -Al 2 O 3 are 75% greater than those on WO 3 at standard conditions. These differences reflect activation enthalpies (ΔH ‡ ) for oxidative cleavage of 4-octene that are much lower for the isolated WO x sites (36±3 and 60±6 kJ∙mol -1 for WO x -Al 2 O 3 and WO 3 , respectively) and correlate strongly with the difference between enthalpies of adsorption for epoxyoctane (ΔH ads,epox ), which resembles the transition state for epoxidation. The WO x -Al 2 O 3 catalysts mediate oxidative cleavage of oleic acid with H 2 O 2 following a mechanism comparable to that for 4-octene. The WO 3 materials, however, form only the epoxide and do not cleave the C-C bond or produce aldehydes and acids. These differences reflect the distinct site requirements for these reaction pathways and indicate that acid sites required for diol formation are strongly inhibited by oleic acids and epoxides on WO 3 whereas the Al 2 O 3 support provides sites competent for this reaction and increase the yield of the oxidative cleavage products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Degradation mechanism of blended cement pastes in sulfate-bearing environments under applied electric fields: Sulfate attack vs. decalcification

Applied electric fields, the reason behind stray currents, accelerate the ingress of sulfate into cementitious materials. To identify mitigation approaches, this study investigates the effects of slag and fly ash on sodium sulfate attacks of cement pastes under a constant electric current. The mineralogical alterations induced by the attacks were analyzed using X-ray diffractometry, thermogravimetric analysis, scanning electron microscopy, and thermodynamic modeling. The dissolution of aluminates in the slag and fly ash induced a monosulfate-rich area (>~20 mm from the cathode surface) to form next to the ettringite-rich area on the sample surface (<~20 mm). This effect reduced the availability of SO 4 2– in the pore solution, thereby hindering the penetration of sulfate. Meanwhile, the consumption of portlandite by the pozzolanic reaction lowered the decalcification resistance of the materials. This produced a wide area that endured the decomposition of portlandite and carbonate-AFm. Altogether, blending 30% fly ash did not improve the resistance of the material to either sulfate attacks or decalcification; blending 50% slag can effectively mitigate sulfate ingress, though decalcification may become a governing mechanism in the degradation process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Consequences of Intrapore Liquids on Reactivity, Selectivity, and Stability for Aldol Condensation Reactions on Anatase TiO 2 Catalysts

Abstract This study provides evidence and mechanistic interpretations for the significant consequences of intrapore non‐polar liquids on acetone aldol condensation turnover rates, selectivity to primary dimer products, and catalyst stability for reactions at Lewis acid‐base site pairs on TiO 2 surfaces. These non‐polar liquids confer such benefits through the preferential stabilization of transition states (TS) for adsorption (“entry”) and desorption (“exit”) steps, which place their respective reactants or products within a solvating outer sphere environment. The extent to which non‐polar fluids ( n ‐heptane) form an intrapore liquid phase within TiO 2 voids was obtained from N 2 uptakes using established formalisms that consider the different molal volume, surface tension, and volatility between N 2 and n ‐heptane. Acetone condensation rates are limited by C−H activation, an “entry” step that forms bound prop‐1‐en‐2‐olates via a TS stabilized by intrapore liquids, leading to higher aldol condensation turnover rates as n ‐heptane pressure increases and active TiO 2 surfaces become increasingly immersed within a non‐polar liquid phase. These liquids solvate the late TS structures that mediate the desorption of primary C 6 condensation products even more effectively than those involved in prop‐1‐en‐2‐olate formation or in nucleophilic attack events that later form C−C bonds. Such preferential solvation favors desorption over C−C coupling events, thus disfavoring the formation of larger oligomers that become stranded at active sites, thus leading to much slower deactivation. Moreover, solvation by non‐polar liquids also leads to C 6 alkanones as the sole products formed in a single surface sojourn. These effects of a non‐polar dense phase circumvent the inherent stability, reactivity, and selectivity hurdles that have precluded practical aldol condensation catalysis on Lewis acid‐base pairs at oxide surfaces; these consequences are demonstrated here for TiO 2 catalysts, acetone aldol condensation reactions, and n ‐heptane as the non‐polar liquid but through strategies, concepts, and mechanistic features that extend to other systems. More generally, these observations and their mechanistic origins demonstrate how a contacting liquid preferentially solvates TS structures for elementary steps that involve either reactants arriving from or products entering into an outer sphere environment that contains a dense non‐polar phase.

Kadam, Shashikant A.↗

DOE OSTI2025

Effects of PFOS on the behavior, growth, emergence, and predation susceptibility of larval mosquitoes ( Culex quinquefasciatus )

Per-/polyfluoroalkyl substances (PFAS) have been commonly used over several decades for a variety of products and are very persistent in the environment. However, not much is known about their direct effects on aquatic invertebrates and their ecosystems. We examined the survival, behavior, development, and predation susceptibility of mosquito larvae Culex quinquefasciatus exposed to concentrations of perfluorooctanesulfonic acid (PFOS) ranging from 0.02 to 453.7 µg/L. PFOS exposure resulted in reduced larval survival, with a 48 hour LC50 (concentration with 50 % mortality) of 255.99 µg/L. PFOS exposure also resulted in reduced developmental success and slower maturation to adulthood (and thus slower emergence from the water) compared to control larvae. PFOS also resulted in delays in reaction to prodding stimuli, which were meant to simulate a predator attack, and longer reactions to prodding. Larvae exposed to PFOS also spent more time at the bottom of the water column, rather than at the surface where respiration takes place. Effects of larval mosquito PFOS exposure on predation by unexposed damselfly naiads (genus Ischnura) were not detected. Overall, this research suggests that PFOS impacts mosquito larvae survival, behavior, development, and adult emergence, which could have important implications for food webs or public health given the role of mosquitos as disease vectors.

Food web dynamics↗

DOE OSTI2023

Effect of surface oxides on tritium entrance and permeation in FeCrAl alloys for nuclear fuel cladding: a review

Abstract Iron-chromium-aluminum (FeCrAl) alloys are being considered for the cladding of uranium dioxide fuel in light water reactors (LWRs). FeCrAl alloys have good mechanical properties at temperatures of 300 °C and higher, and have superlative resistance to attack by steam at temperatures of up to 1000 °C and higher. A concern has been raised that the use of FeCrAl for cladding would result in a higher content of tritium in the reactor coolant as compared with the current system where the cladding is a zirconium based alloy. This review shows that the flux of tritium from the fuel rod cavities to the coolant across the fuel cladding wall will be greatly reduced by the presence of oxides on the surface of the cladding. The review of current literature and permeation data show that (a) protective oxides are expected to be present on both sides of the FeCrAl cladding, and (b) depending on the characteristics of these oxide layers it is reasonable to expect about two–three orders of magnitude reduction in tritium permeation, relative to the permeation response in clean, unoxidized condition for FeCrAl steels of interest, around 277 °C–377 °C temperatures.

Electrochemistry↗

DOE OSTI2020

Microstructure geometry for thermal barrier coatings to mitigate CMAS attack

Thermal barrier coatings and methods to make such coatings present improved resistance to CMAS infiltration. The method for forming a thermal barrier coating includes applying a layer of the thermal barrier coating to a component having a surface, forming a plurality of first channels in the thermal barrier coating, and forming a plurality of second channels in the thermal barrier coating. The first channels extend through a thickness of the thermal barrier coating from an interface with the surface of the component to a free surface opposite the interface. The second channels are disposed between the free surface and the interface and extending lengthwise generally parallel to the free surface of the thermal barrier coating.

Jordan, Eric↗

DOE OSTI2023

Microstructure geometry for thermal barrier coatings to mitigate CMAS attack

Jordan, Eric↗

DOE OSTI2023

Atomistic mechanisms of the initial oxidation of stepped Cu 3 Au ( 100 )

Explore the source record for details and available documents.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2022

Removal of Surface Carbonate from Lithium-Ion Battery Cathode Materials via Vapor-Phase Fluorination

Herein, ultrathin metal-fluoride barrier coatings on the surface of lithium-ion battery (LIB) cathodes can improve cycling stability and prevent corrosion by acidic byproducts in the electrolyte. Atomic layer deposition (ALD) is an effective method to deposit ultrathin metal fluoride coatings on LIB cathodes. Although numerous studies have demonstrated the benefit of ALD metal fluoride coatings to LIB performance, comparatively few works have examined the effect of individual ALD precursors on the cathode surface. This paper uses X-ray photoelectron spectroscopy (XPS) measurements to elucidate the surface chemical changes on LIB cathode material surfaces upon exposure to the ALD metal fluoride precursor, hydrogen fluorine pyridine (HFPy). We found a decrease in surface carbonate and an increase in surface fluoride after HFPy exposure suggesting the conversion of lithium carbonate (Li 2 CO 3 ) to lithium fluoride (LiF). This conversion is desirable given that Li 2 CO 3 degrades LIB performance, whereas LiF provides an excellent physio-chemical barrier against chemical attack during cycling. Scanning transmission electron microscopy, X-ray energy dispersive spectroscopy, and XPS measurements following HFPy exposure to Li 2 CO 3 powder revealed the formation of a conformal LiF shell around the Li 2 CO 3 particles. Finally, we confirmed the complete conversion of similar to 7 nm ALD Li 2 CO 3 films on silicon from HFPy exposure using XPS and spectroscopic ellipsometry. The elimination of problematic Li 2 CO 3 from LIB cathode surfaces and conversion into a protective LiF coating via a single precursor vapor treatment may provide a cost-effective method for enhancing LIB performance.

25 ENERGY STORAGE↗

DOE OSTI2021

Catalytic CO Oxidation on MgAl 2 O 4 -Supported Iridium Single Atoms: Ligand Configuration and Site Geometry

Probing and understanding the local chemical environment of an active site is essential for designing high-performance single-atom catalysts (SACs). Density functional theory (DFT) calculations were performed to investigate the ligand configuration and site geometry of MgAl 2 O 4 -supported iridium single atoms (Ir-1) toward catalytic carbon monoxide (CO) oxidation. We employed MgAl 2 O 4 (111) and MgAl 2 O 4 (211) as the model substrates with adsorbed Ir single atoms of different site geometries. DFT calculations revealed that the Mg-site on MgAl 2 O 4 (111) and the step site on MgAl 2 O 4 (211) are the most stable adsorption sites for Ir single atoms. Irrespective of site choices, CO oxidation on supported Ir single atoms follows the Eley-Rideal (E-R) mechanism, in which the surface oxygen vacancies close to the Ir single atoms activate molecular O 2 with a negligible barrier and the rate-limiting step is the gas-phase CO directly attacking the O-Ir species that is modulated by a CO ligand. Furthermore, first-principles X-ray absorption near-edge spectra of reaction intermediates along with in situ/operando X-ray absorption spectroscopy (XAS) suggest that Ir single atoms adsorb primarily on the step sites of MgAl 2 O 4 . However, microkinetic modeling predicts that a higher activity can be attained on the equally stable Mg-site, maximizing the population of which in catalyst synthesis might prove fruitful in future studies. Electronic structure analysis indicates that the CO ligand increases the reactivity of adsorbed oxygen atoms bound to Ir single atoms by increasing the antibonding nature of the O-Ir bond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Improving CLM5.0 Biomass and Carbon Exchange Across the Western United States Using a Data Assimilation System

The Western United States is dominated by natural lands that play a critical role for carbon balance, water quality, and timber reserves. This region is also particularly vulnerable to forest mortality from drought, insect attack, and wildfires, thus requiring constant monitoring to assess ecosystem health. Carbon monitoring techniques are challenged by the complex mountainous terrain, thus there is an opportunity for data assimilation systems that combine land surface models and satellite-derived observations to provide improved carbon monitoring. Here, we use the Data Assimilation Research Testbed to adjust the Community Land Model (CLM5.0) with remotely sensed observations of leaf area and above-ground biomass. The adjusted simulation significantly reduced the above-ground biomass and leaf area, leading to a reduction in both photosynthesis and respiration fluxes. The reduction in the carbon fluxes mostly offset, thus both the adjusted and free simulation projected a weak carbon sink to the land. This result differed from a separate observation-constrained model (FLUXCOM) that projected strong carbon uptake to the land. Simulation diagnostics suggested water limitation had an important influence upon the magnitude and spatial pattern of carbon uptake through photosynthesis. We recommend that additional observations important for water cycling (e.g., snow water equivalent, land surface temperature) be included to improve the veracity of the spatial pattern in carbon uptake. Furthermore, the assimilation system should be enhanced to maximize the number of the simulated state variables that are adjusted, especially those related to the recommended observed quantities including water cycling and soil carbon.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Critical role of solvent-modulated hydrogen-binding strength in the catalytic hydrogenation of benzaldehyde on palladium

Protic and non-protic solvents influence the rate of benzaldehyde hydrogenation on Pd by one order of magnitude in the following sequence of increasing reactivity, dioxane < tetrahydrofuran < water < methanol. Despite these differences, the reaction pathway does not change; the majority of turnovers occurs via a Langmuir-Hinshelwood mechanism by stepwise addition of sorbed H to sorbed benzaldehyde, first to the carbonyl O and then to the C atom of the formyl group, forming benzyl alcohol. An analysis of the solvation energies shows that both ground and transition states are destabilized by the solvents compared to the same reaction at the gas-solid interface. The destabilization extent of the reacting organic substrates in both states are similar and, therefore, compensate each other, making the net kinetic effects inconsequential. In consequence, the marked reactivity differences arise solely from the differences in the surface stabilization of adsorbed hydrogen adatoms moderated by the four solvents-more weakly bound hydrogen adatoms, because of their solvation by solvent, exhibit higher rates of their hydrogenation reaction in kinetically relevant attack on the C atom.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗