Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “angle control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A Comprehensive Method to Mitigate Forced Oscillations in Large Interconnected Power Grids

Multiple severe forced oscillation events have recently been observed across the North American interconnections and around the world. These forced oscillations have caused power swings, limited power transfer capability, damaged equipment, and persisted indefinitely until the driving source was located and removed. This paper proposes a comprehensive method to mitigate forced oscillations. Once a forced oscillation is detected, a new source location algorithm can be used to locate the source based on the oscillation mode angle without requiring system topology information. If the source cannot be quickly located and removed, a control strategy can be activated to modulate the active power of utility-scale inverterbased battery energy storage systems (BESSs) to reduce the energy of forced oscillations to a safe level and allow sufficient time for locating the exact source. The proposed source location algorithm is validated using measurements collected during the January 11, 2019 forced oscillation event in North America and other actual grid events, while the proposed control strategy is verified using the Eastern Interconnection dynamic model under the replicated January 11, 2019 forced oscillation event. The simulation results demonstrated that the proposed source location algorithm can accurately identify the forced oscillation source, and the proposed control strategy can significantly reduce forced oscillation energy.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

DOE 10658 Project Sensitivity-Driven Wide Area Protection (SWAP) Coordination Tools for IBRs

Utilities have seen a rapid increase in solar, wind, and battery energy storage systems that interconnect to their electric system through inverters. Inverter-Based Resources (IBRs) have fault current characteristics that are unlike the fault current response of traditional rotating-machine-based generators, which is well-known and repeatable. IBR’s non-traditional fault current behavior is due to the IBR control scheme, which is configured to provide a clean AC output but also protects the inverter’s sensitive power electronics devices from damage from conditions such as overcurrent. This results in a low fault current magnitude, low or no negative sequence current injection, the variability of sequence component currents, the variability of voltage with respect to current angles, and the lack of inertia. The control scheme also results in a fault current response that can vary between manufacturers and between models of the same manufacturer. High penetration of IBRs can adversely affect the protection schemes applied in areas with high penetration of IBRs. With the proliferation of IBRs, utilities are finding out that conventional protection schemes are not adequately equipped to protect the electric systems. This is mainly because the existing protection elements and practices have been designed based on the fault current response of conventional rotating machines. In several cases, the available literature does not provide any clear solution for the issues when the protection scheme does not operate properly near IBRs. This report identifies various protection challenges due to IBRs that industry is facing, from the utility perspective. Instead of focusing on one issue, this report looks broadly at all the challenges that system protection has experienced with high penetration of IBRs. Based on the IBR response from various utilities during real fault events and gathering perspectives from different utility SMEs via questionnaire, the report summarizes the gathered data and internal experiences.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Utilities Perspective on Protection Challenges with High IBR Penetration

Utilities have seen rapid increase in Solar, Wind, and Battery Energy Storage Resources that interconnect to their electric system through Inverters. Inverter-Based Resources (IBRs) have fault current characteristics that are unlike the fault current response of traditional rotating-machine-based generators, which is well known and repeatable. IBR’s non-traditional fault current behavior is due to the IBR control scheme, which is configured to provide a clean AC output but also protect the inverter’s sensitive power electronics devices from damage, one source of which is overcurrent. This results in low fault current magnitude, low or no negative sequence current injection, the variability of sequence component currents, the variability of voltage with respect to current angles, and the lack of inertia. The control scheme also results in a fault current response that can vary between manufactures and between models of the same manufacturer. High penetration of IBRs can adversely affect the protection schemes applied in areas with high penetration of IBRs. With the proliferation of IBRs, utilities are finding out that conventional protection schemes are not adequately equipped to protect the electric systems. This is mainly because the existing protection elements and practices have been designed based on the fault current response of conventional rotating machines. In several cases, the available literature does not provide any clear solution for the issues when the protection scheme does not operate properly near IBRs. This presentation identifies various protection challenges due to IBRs that industry is facing, from the utility perspective. Instead of facing on one issue, we are looking broadly on all the challenges that system protection has experienced with high penetration of IBRs. Based on the IBR response from various utilities during real fault events and gathering perspective from different utility SMEs via questionnaire, the presentation summarizes on gathered data and internal experiences.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Utility Perspective on Protection Challenges with High Penetration of IBRs

Utilities have seen rapid increase in Solar, Wind, and Battery Energy Storage Resources that interconnect to their electric system through Inverters. Inverter-Based Resources (IBRs) have fault current characteristics that are unlike the fault current response of traditional rotating-machine-based generators, which is well known and repeatable. IBR’s non-traditional fault current behavior is due to the IBR control scheme, which is configured to provide a clean AC output but also protect the inverter’s sensitive power electronics devices from damage, one source of which is overcurrent. This results in low fault current magnitude, low or no negative sequence current injection, the variability of sequence component currents, the variability of voltage with respect to current angles, and the lack of inertia. The control scheme also results in a fault current response that can vary between manufactures and between models of the same manufacturer. High penetration of IBRs can adversely affect the protection schemes applied in areas with high penetration of IBRs. With the proliferation of IBRs, utilities are finding out that conventional protection schemes are not adequately equipped to protect the electric systems. This is mainly because the existing protection elements and practices have been designed based on the fault current response of conventional rotating machines. In several cases, the available literature does not provide any clear solution for the issues when the protection scheme does not operate properly near IBRs. This report / presentation identifies various protection challenges due to IBRs that industry is facing, from the utility perspective. Instead of facing on one issue, this report looks broadly on all the challenges that system protection has experienced with high penetration of IBRs. Based on the IBR response from various utilities during real fault events and gathering perspective from different utility SMEs via questionnaire, the report summarizes on gathered data and internal experiences.

14 SOLAR ENERGY↗
DOE OSTI2024

Utility Perspective on Protection Challenges with High IBR Penetration [Slides]

Utilities have seen rapid increase in Solar, Wind, and Battery Energy Storage Resources that interconnect to their electric system through Inverters. Inverter-Based Resources (IBRs) have fault current characteristics that are unlike the fault current response of traditional rotating-machine-based generators, which is well known and repeatable. IBR’s non-traditional fault current behavior is due to the IBR control scheme, which is configured to provide a clean AC output but also protect the inverter’s sensitive power electronics devices from damage, one source of which is overcurrent. This results in low fault current magnitude, low or no negative sequence current injection, the variability of sequence component currents, the variability of voltage with respect to current angles, and the lack of inertia. The control scheme also results in a fault current response that can vary between manufactures and between models of the same manufacturer. High penetration of IBRs can adversely affect the protection schemes applied in areas with high penetration of IBRs. With the proliferation of IBRs, utilities are finding out that conventional protection schemes are not adequately equipped to protect the electric systems. This is mainly because the existing protection elements and practices have been designed based on the fault current response of conventional rotating machines. In several cases, the available literature does not provide any clear solution for the issues when the protection scheme does not operate properly near IBRs. This report identifies various protection challenges due to IBRs that industry is facing, from the utility perspective. Instead of facing on one issue, this report looks broadly on all the challenges that system protection has experienced with high penetration of IBRs. Based on the IBR response from various utilities during real fault events and gathering perspective from different utility SMEs via questionnaire, the report summarizes on gathered data and internal experiences.

14 SOLAR ENERGY↗
DOE OSTI2021

Visual Tool for Assessing Stability of DER Configurations on Three-Phase Radial Networks

Here, we present a method and tool for evaluating the placement of Distributed Energy Resources (DER) on distribution circuits in order to control voltages and power flows. Our previous work described Phasor-Based Control (PBC), a novel control framework where DERs inject real and reactive power to track voltage magnitude and phase angle targets. Here, we employ linearized power flow equations and integral controllers to develop a linear state space model for PBC acting on a three-phase unbalanced network. We use this model to evaluate whether a given inverter-based DER configuration admits a stable set of controller gains, which cannot be done by analyzing controllability nor by using the Lyapunov equation. Instead, we sample over a parameter space to identify a stable set of controller gains. Our stability analysis requires only a line impedance model and does not entail simulating the system or solving an optimization problem. We incorporate this assessment into a publicly available visualization tool and demonstrate three processes for evaluating many control configurations on the IEEE 123-node test feeder (123NF).

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Caprock Remains Water Wet Under Geologic CO 2 Storage Conditions

Abstract Carbon storage technology is primarily targeted in saline formations, which is a porous rock matrix filled with brine, sealed with a low permeability caprock. There are significant variations of CO 2 wetting properties, typically reported in the literature as contact angle of CO 2 and brine interacting with a rock material, suggesting that CO 2 could become wetting under geostorage conditions and negatively impact containment effectiveness. Here, we performed the first controlled laboratory measurements of CO 2 ‐brine contact angles on shale rocks from low permeability sealing formations with distinctive mineralogic properties—calcite‐rich, quartz‐rich, and dolomite‐rich. We targeted temperatures at 40° and 100°C, pressures at 8.3, 34.5, and 62.1 MPa, and salinity at 35,000 and 260,000 ppm. Results show no significant change in contact angle with mineralogy, temperature, pressure, salinity, and CO 2 bubble size. We conclude that caprocks will remain water‐wet at geologic CO 2 storage conditions and will not lose their capillary sealing capacity.

Tapriyal, Deepak↗
DOE OSTI2024

A Comprehensive Strategy for Grid Forming Control in DC Coupled Photovoltaic and Battery Energy Storage Inverters

This paper presents an integrated DC-DC and DCAC grid-forming control strategy for DC-coupled photovoltaic (PV) plus battery energy storage systems, considering the effect of DC link voltage variations caused by direct PV connections. A power reference algorithm determines power distribution between the PV and battery to the grid while observing device power ratings to prevent the over-rating of components and keep the battery's state of charge within an acceptable range. The simulated utility-scale model in MATLAB/Simulink illustrates its ability against extreme phase angle variation contingencies in the grid while controlled through grid-forming control with a fast dynamic on DC link voltage. The simulation results confirm the effectiveness of the proposed control in integrating PV plus battery configurations with grid forming control and maintaining reliable grid operation under severe grid disturbances.

battery, boost, control, energy storage, grid form↗
DOE OSTI2025

Conceptual study on using Doppler backscattering to measure magnetic pitch angle in tokamak plasmas

We introduce a new approach to measure the magnetic pitch angle profile in tokamak plasmas with Doppler backscattering (DBS), a technique traditionally used for measuring flows and density fluctuations. The DBS signal is maximised when its probe beam's wavevector is perpendicular to the magnetic field at the cutoff location, independent of the density fluctuations [Hillesheim \emph{et al} 2022 \emph{Nucl. Fusion} \textbf{55} 073024]. Hence, if one could isolate this effect, DBS would then yield information about the magnetic pitch angle. By varying the toroidal launch angle, the DBS beam reaches cutoff with different angles with respect to the magnetic field, but with other properties remaining similar. Hence, the toroidal launch angle which gives maximum backscattered power is thus that which is matched to the pitch angle at the cutoff location, enabling inference of the magnetic pitch angle. We performed systematic scans of the DBS toroidal launch angle for repeated DIII-D tokamak discharges. Experimental DBS data from this scan were analysed and combined with Gaussian beam-tracing simulations using the Scotty code [Hall-Chen \emph{et al} 2022 \emph{Plasma Phys. Control. Fusion} \textbf{64} 095002]. The pitch-angle inferred from DBS is consistent with that from magnetics-only and motional-Stark-effect-constrained (MSE) equilibrium reconstruction in the edge. In the core, the pitch angles from DBS and magnetics-only reconstructions differ by one to two degrees, while simultaneous MSE measurements were not available. The uncertainty in these measurements was under a degree; we show that this uncertainty is primarily due to the error in toroidal steering, the number of toroidally separated measurements, and shot-to-shot repeatability. We find that the error of pitch-angle measurements can be reduced by optimising the poloidal launch angle and initial beam properties. Since DBS has high spatial and temporal resolutions, is non-perturbative, does not require neutral beams, and is likely robust to neutron damage of and debris on the first mirrors, using DBS to measure the pitch angle in future fusion energy systems is especially appealing.

beam tracing↗
DOE OSTI2026

Closed-Loop Wind Turbine Controllers for Active Wake Mixing Strategies

Wind turbine active wake mixing (AWM) is an exciting new field of research where dynamic actuation, usually on the blade pitch angles, is used to increase wind farm-wide power production. From a controls perspective, the current state-of-the-art AWM strategies are very simple: a dynamic, usually periodic, reference signal is prescribed to actuators in an open-loop (OL) fashion. The actuation is then presumed to have a certain desired effect on the system, i.e., the wind turbine and the flow it affects. However, this system is highly nonlinear and experiences disturbances in the form of wind variations that are not known a priori. As a result, the OL approach might not yield optimal results. In this article, a novel approach is presented, which closes the loop on AWM controllers. A feedback loop is implemented, which uses measurements of the individual blade bending moments that are widely available on modern wind turbines to determine the individual blade pitch angles. A proof of concept of this implementation is presented in this article, and a thorough comparison with the OL method is executed using high-fidelity flow simulations. These simulations show that the novel closed-loop controller does not substantially increase wake mixing but achieves similar performance as the OL controller while reducing fatigue loads on the controlled turbine.

17 WIND ENERGY↗
DOE OSTI2022

Interaction-induced velocity renormalization in magic-angle twisted multilayer graphene

Abstract Twistronics heterostructures provide a novel route to control the electronic single particle velocity and thereby to engineer strong effective interactions. Here we show that the reverse may also hold, i.e. that these interactions strongly renormalize the band structure. We demonstrate this mechanism for alternating-twist magic-angle three- and four-layer graphene at charge neutrality and in the vicinity of a phase transition which can be described by an Ising Gross-Neveu critical point corresponding, e.g. to the onset of valley Hall or Hall order. While the non-interacting model displays massless Dirac excitations with strongly different velocities, we show that interaction corrections make them equal in the infrared. However, the renormalization group flow of the velocities and of the coupling to the critical bosonic mode is strongly non-monotonic and dominated by the vicinity of a repulsive fixed point. We predict experimental consequences of this theory for tunneling and transport experiments and discuss the expected behavior at other quantum critical points, including those corresponding to intervalley coherent ordering.

Classen, Laura↗
DOE OSTI2024

The melt memory effects in polymer crystallization

This paper presents a systematic review of the literature on the melt memory effects observed in polymers, an area that has engendered considerable debate for over 50 years. Recent advances in experimental techniques have provided fresh insights into how a polymer's thermal history influences its recrystallization behavior. It has been observed that given other conditions unchanged, the crystallization temperature during recrystallization decreases with an increase in the melt temperature T s above the melting point T m until a critical melt temperature is attained. This phenomenon also extends to the half-time of crystallization and the secondary structures, such as lamellar thickness, of semi-crystalline polymers. Despite these findings, a comprehensive constitutive model that encapsulates polymer melt memory effects remains elusive. Cutting-edge instrumentation, including in situ small and wide-angle X-ray scattering, temperature-controlled Fourier transform infrared spectroscopy, and flash differential scanning calorimetry, have posed significant challenges to the traditional nucleation and growth models established in the 1970s. These models are foundational to our understanding of polymer crystallization, which is an integral part of polymer processing and production. In this review, the historical contours of this discourse are traced, with an examination of both the recent experimental breakthroughs and theoretical advancements pertinent to polymer melt memory effects. In conclusion, this paper delves into the prevailing theories of polymer nucleation and crystallization and engages with theoretical discussions and numerical simulations that attempt to elucidate and rationalize these melt memory phenomena.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanisms of Dynamic Near-Wake Modulation of a Utility-Scale Wind Turbine

The current study uses large eddy simulations to investigate the transient response of a utility-scale wind turbine wake to dynamic changes in atmospheric and operational conditions, as observed in previous field-scale measurements. Most wind turbine wake investigations assume quasi-steady conditions, but real wind turbines operate in a highly stochastic atmosphere, and their operation (e.g. blade pitch, yaw angle) changes constantly in response. Furthermore, dynamic control strategies have been recently proposed to optimize wind farm power generation and longevity. Therefore, improved understanding of dynamic wake behaviours is essential. First, changes in blade pitch are investigated and the wake expansion response is found to display hysteresis as a result of flow inertia. The time scales of the wake response to different pitch rates are quantified. Next, changes in wind direction with different time scales are explored. Under short time scales, the wake deflection is in the opposite direction of that observed under quasi-steady conditions. Finally, yaw changes are implemented at different rates, and the maximum inverse wake deflection and time scale are quantified, showing a clear dependence on yaw rate. To gain further physical understanding of the mechanism behind the inverse wake deflection, the streamwise vorticity in different parts of the wake is quantified. The results of this study provide guidance for the design of advanced wake flow control algorithms. The lag in wake response observed for both blade pitch and yaw changes shows that proposed dynamic control strategies must implement turbine operational changes with a time scale of the order of the rotor time scale or slower.

flow-structure interactions↗
DOE OSTI2026

Transition Metal Dichalcogenide MoS 2 : Oxygen and Fluorine Functionalization for Selective Plasma Processing

Low-temperature plasma processing is a promising technique for tailoring transition metal dichalcogenides (TMDs). For chalcogen substitution processing, a key challenge is to identify the ion energy window that enables selective chalcogen removal while preserving the metal lattice. Using ab initio molecular dynamics (AIMD), we demonstrate that oxygen and fluorine functionalization widen the processing window by significantly lowering the sulfur sputtering energy threshold (E sputt,S ) of MoS 2 from ∼30 to ∼10 eV via formation of sputtering products such as SO 2 and SF n . Additionally, we show that experimentally relevant cryogenic temperatures strongly affect E sputt,S (T). The dependence is confirmed via AIMD and also predicted by a mechanistic parameter-free theory, suggesting that E sputt (T) generalizes to other TMDs, functionalizations, and surface impact conditions. Our results highlight oxygen/fluorine functionalization, ionic impact angle, and material temperature to be key control parameters for selective, damage-controlled chalcogen removal in TMD processing.

Polyachenko, Yury [Princeton Plasma Physics Labora↗
DOE OSTI2020

Bio-inspired gas sensing: boosting performance with sensor optimization guided by “machine learning”

The performance of existing gas sensors often degrades in field conditions because of the loss of measurement accuracy in the presence of interferences. Thus, new sensing approaches are required with improved sensor selectivity. We are developing a new generation of gas sensors, known as multivariable sensors, that have several independent responses for multi-gas detection with a single sensor. In this study, we analyze the capabilities of natural and fabricated photonic three-dimensional (3-D) nanostructures as sensors for the detection of different gaseous species, such as vapors and non-condensable gases. We employed bare Morpho butterfly wing scales to control their gas selectivity with different illumination angles. Next, we chemically functionalized Morpho butterfly wing scales with a fluorinated silane to boost the response of these nanostructures to the vapors of interest and to suppress the response to ambient humidity. Further, we followed our previously developed design rules for sensing nanostructures and fabricated bioinspired inorganic 3-D nanostructures to achieve functionality beyond natural Morpho scales. These fabricated nanostructures have embedded catalytically active gold nanoparticles to operate at high temperatures of ≈300 °C for the detection of gases for solid oxide fuel cell (SOFC) applications. Our performance advances in the detection of multiple gaseous species with specific nanostructure designs were achieved by coupling the spectral responses of these nanostructures with machine learning (a.k.a. multivariate analysis, chemometrics) tools. Our newly acquired knowledge from studies of these natural and fabricated inorganic nanostructures coupled with machine learning data analytics allowed us to advance our design rules for sensing nanostructures toward the required gas selectivity for numerous gas monitoring scenarios at room and high temperatures for industrial, environmental, and other applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Atomic force microscopy phase imaging of epitaxial graphene films

Abstract Dynamic mode atomic force microscopy phase imaging is known to produce distinct contrast between graphene areas of different atomic thickness. But the intrinsic complexity of the processes controlling the tip motion and the phase angle shift excludes its use as an independent technique for a quantitative type of analysis. By investigating the relationship between the phase shift, the tip-surface interaction, and the thickness of the epitaxial graphene areas grown on silicon carbide, we shed light on the origin of such phase contrast, and on the complex energy dissipation processes underlying phase imaging. In particular, we study the behavior of phase shift and energy dissipation when imaging the interfacial buffer layer, single-layer, and bilayer graphene regions as a function of the tip-surface separation and the interaction forces. Finally, we compare these results with those obtained on differently-grown quasi free standing single- and bilayer graphene samples.

Lavini, Francesco (ORCID:0000000257223040)↗
DOE OSTI2022

Spin-Transfer-Torque Oscillator with an Antiferromagnetic Exchange-Coupled Composite Free Layer

We present an antiferromagnetically exchange-coupled composite (soft and hard layers) spin torque oscillator (AF-ECC STO) and demonstrate its operation via both analytical and micromagnetic modeling. The operation exploits the exchange field due to the antiferromagnetic coupling between soft and hard sublayers of the free layer as well as on the easy-plane anisotropy of the soft sublayer. Optimized AF-ECC STO structures can generate large-amplitude magnetization oscillations, which can be tuned over a broad frequency range with precessions mostly generated by the soft layer. We demonstrate that the AF-ECC STO structure offers flexibility in current control of the oscillation frequency and magnetization angle for realistic material parameters.

42 ENGINEERING↗
DOE OSTI2023

Reducing Conservativeness of Polytopic Linear-Parameter-Varying Robust Vehicle Sideslip Angle Observer Through Minimum-Area Convex Quadrilateral Design

The polytopic linear-parameter-varying (LPV) method has become increasingly popular for designing intelligent control and estimation systems for ground vehicles, particularly for the vehicle sideslip angle observer. In vehicle lateral dynamics, the vehicle longitudinal velocity-induced nonlinearities are conventionally outer-approximated with polytopes such as rectangles or triangles to obtain a polytopic LPV system. Yet, such polytopic approximations tend to be conservative and may lead to inadequate observer performance. To address this issue, a minimum-area convex quadrilateral construction is proposed in this paper to reduce design conservatism. The suggested design is demonstrated through the synthesis of an LPV H ∞ robust vehicle sideslip angle observer. Furthermore, a dSPACE-ASM simulation study is conducted to demonstrate the effectiveness and the advantage of the proposed polytopic construction over a baseline approach.

Zhou, Xingyu↗