Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aluminosilicates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

130 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Thermochemical Interactions of Yttria-Stabilized Zirconia and Molten Lunar Regolith Simulants

Oxygen produced from lunar resources through in-situ resource utilization (ISRU) is critical to maintaining a permanent human presence on the lunar surface. Molten regolith electrolysis and carbothermal reduction are two promising ISRU techniques for generating oxygen directly from lunar regolith, which is primarily a mixture of oxide minerals; however, both processes require operating temperatures of 1600C to melt lunar regolith and dissociate the molten oxides. These conditions limit the use of many oxide refractory materials, such as Al2O3 and MgO, due to rapid degradation resulting from reactions between the refractory materials and molten lunar regolith. Yttria-stabilized zirconia (YSZ) is a promising refractory oxide to provide containment of molten regolith while demonstrating limited reactivity. This work focuses on corrosion studies of YSZ powders and dense YSZ crucibles in contact with molten lunar mare and highlands regolith simulants at 1600C. The interactions between YSZ and molten regolith are characterized using SEM/EDS, XRD, and EBSD with an emphasis on elemental and microstructural analysis to assess reactivity and degradation of YSZ. Due to lunar regolith’s similar composition to calcium-magnesium-aluminosilicates (CMAS) and YSZ’s usage as a thermal barrier coating, these interactions can serve to inform YSZ/CMAS behavior by simulating cases of elevated CMAS/YSZ ratios and for higher than intended gas turbine temperatures.

Kevin Yu↗
NASA NTRSDate not supplied

Thermochemical and microstructural contributions of high temperature particle erosion durability in CMAS exposed EBCs

Particulate/debris damage caused by ingestion of calcium magnesium aluminosilicates (CMAS) hinders the use of environmental barrier coatings (EBCs) to protect SiC-based ceramic matrix composite components in next generation gas turbine engines. Similarly, ingestion of any debris in the engine can lead to mechanical damage and recession of coatings due to particulate erosion. Investigating particulate interactions at relevant engine conditions is crucial in determining limiting mechanisms in the operating lifetime of EBCs. This study assesses the effects of extrinsic phase formation and microstructural changes due to CMAS interactions on the erosion durability of Yb 2 Si 2 O 7 -based EBCs in NASA Glenn’s Erosion Burner Rig Facility. CMAS exposures and erosion testing were carried out at 1316°C. Using 60 µm Al 2 O 3 particles as the erodent material, the effects of CMAS loading on erosion durability at various impingement angles were evaluated.

Jamesa L. Stokes↗
NASA NTRSDate not supplied

Exploring the Effect of EBC Composition on CMAS Wetting Behavior

Rare-earth disilicate (REDS) materials are existing materials used in environmental barrier coating (EBC) for the protection of structural materials in the hot-section of turbine engines. REDS interactions with molten calcium-magnesium-aluminosilicate (CMAS) debris are of interest to understand molten CMAS attack and improve CMAS mitigation strategies. This work assesses the effect of REDS composition on CMAS wetting by investigating wetting angle, spreading, and reactivity. Freestanding atmospheric plasma spray (APS) REDS coatings (for RE = Y, La, Nd, Gd, Yb, Lu) were exposed to 10 mg of CMAS (Ca33-Mg9-Al13-Si45 in single cation mol%) in stagnant lab air at 1250C. APS YbDS was compared to a dense spark plasma sintered (SPS) phase-pure Yb2Si2O7 and a nominal 20 vol% phase-mixture of Yb 2 SiO 5 in Yb 2 Si 2 O 7 (20YbMS/YbDS). CMAS mass was held constant but specimen surface areas varied, yielding a range of loading between ~6 and 10 mg/cm2. CMAS was loaded as a cylindrical rod atop the specimen surface, polished to 4000 grit, and heated to temperature in a Linseis L74/HS/1700 heating microscope. The heating microscope measured the evolution of molten CMAS diameter, height, and contact angle. Molten CMAS diameter at 1150C and contact angle measurements after two hours of exposure at 1250C yielded a positive trend with rare-earth cation size. There was no statistically significant difference in CMAS wetting behavior between SPS YbDS and 20YbMS/YbDS. Post-exposure specimens were examined in plan view and cross-section with XRD, SEM, and EDS. CMAS spreading was cross-examined using plan view SEM, while reactivity utilized plan view XRD and cross-sectional SEM/EDS.

Clark Luckhardt↗
NASA NTRSDate not supplied

Multiscale Modeling of Fracture Strength in Fibrous Thermal Protection System Materials

This work presents a multiscale modeling approach to predict the fracture strength of fibrous Thermal Protection System (TPS) materials. The model assumes that system failure is initiated at the joints between individual fibers. We investigated three distinct TPS compositions: amorphous silica, alumina and aluminosilicate fibers. Molecular dynamics (MD) simulations were employed to determine the fracture strength values of these fiber joints for both material systems. These fracture strength values were then integrated into simulations of 3D randomly populated fiber structures, where tensile load transfer occurs through the fiber joints. These microscale properties are upscaled through a renormalization approach [1] to predict macroscale tensile strength of 3D random fiber networks, accounting for joint-dominated failure and effective load-bearing area. The study concludes by demonstrating the resulting strength variation as a function of material composition, fiber density, and morphology. We also show validation of results by comparing them against explicit fiber finite element (FE) modeling [2] where fiber joint fracture is represented by cohesive elements.

Jaehyun Cho↗