SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Fast economical fabrication produces wedge-shaped beam splitter with 0.3 micrometer edge, compared to conventional methods that have yielded 2 micrometer edges. Typical beam splitter made by new process is prism-shaped with right-triangle cross-section.
In-depth gap heating ratios for Orbiter RSI tile sidewalls were predicted based on near steady state temperature measurements obtained from double wedge model tests. An analysis was performed to derive gap heating ratios which would result in the best fit of test data; provide an assessment of open gap response, and supply the definition of gap filler requirements on the Orbiter. A comparison was made of these heating ratios with previously derived ratios in order to verify the extrapolation of the wing glove data to Orbiter flight conditions. The analysis was performed with the Rockwell TPS Multidimensional Heat Conduction Program for a 3-D, 2.0-inch thick flat RSI tile with 255 nodal points. The data from 14 tests was used to correlate with the analysis. The results show that the best-fit heating ratios at the station farthest upstream on the model for most gap depths were less than the extrapolated values of the wing glove model heating ratios. For the station farthest downstream on the model, the baseline heating ratios adequately predicted or over-predicted the test data.
Arc-jet tests at NASA/JSC have been conducted recently to evaluate the performance of the Orbiter Thermal Protection System (TPS) on three critical areas of the side and top of the Orbiter fuselage: (1) cargo bay door, (2) crew access door, and (3) LRSI/FRSI joint regions. Test articles corresponding to these three areas on the Orbiter were mounted in an arc-jet test chamber in a blunted-wedge holder and exposed to hypersonic flow at various angles of attack. The effects of flow direction, heating load, and overtemperature were investigated. In addition, the reuse capability of the TPS materials was evaluated, along with the protection of the pressure seals within the test articles. Thermal match model predictions correlated well with primary structure thermocouple data. Heating rate and pressure predictions based on a nonequilibrium flow field computer program showed good agreement with arc-jet test data and existing hypersonic flow theories.
The results of a static calibration of the two dimensional wedge nozzles on a STOL configuration of a large-scale fighter model are reported. These nozzles internally turn the efflux produced by two turbojets down 25 degrees and exhaust it over the deflected trailing edge of the wing. This arrangement provides direct thrust lift, enhances wing lift by producting supercirculation, and provides thrust vectoring by varying the deflection of the wing's trailing edge. The thrust is vectored from 10 deg to 38 deg. This system was calibrated with spanwise blowing for augmentation of the leading-edge vortex. When 16% of the turbojet efflux is blown spanwise, the thrust recovered is 92% of the thrust produced when the total efflux is exhausted longitudinally.
A development is presented for the Green's function for a point source in the vicinity of a rigid wedge. The diffraction contributions to the Green's function for arbitrary source and listener location is expressed in a form which can be readily evaluated using the Laguerre technique for numerical integration. The present approach offers the advantages of efficient numerical evaluation and of relatively straightforward reduction to well-known analytical approximations in limiting cases. Comparisons with previously obtained experimental and numerical results obtained by Ambaud and Bergassoli (1972) are presented. The comparison with the experimental results is excellent; the advantages of the present numerical technique, vis a vis that of Ambaud and Bergassoli, are pointed out.
The paper examines geometries employing position-dependent charge partitioning to obtain a two-dimensional position signal from each detected photon or particle. Requiring three or four anode electrodes and signal paths, images have little distortion and resolution is not limited by thermal noise. An analysis of the geometrical image nonlinearity between event centroid location and the charge partition ratios is presented. In addition, fabrication and testing of two wedge-and-strip anode systems are discussed. Images obtained with EUV radiation and microchannel plates verify the predicted performance, with further resolution improvements achieved by adopting low noise signal circuitry. Also discussed are the designs of practical X-ray, EUV, and charged particle image systems.
Elastic-plastic stress-strain analyses were performed for single-edge wedge alloys subjected to thermal cycling in fluidized beds. Three cases (NASA TAZ-8A alloy under one cycling condition and 316 stainless steel alloy under two cycling conditions) were analyzed by using the MARC nonlinear, finite-element computer program. Elastic solutions from MARC showed good agreement with previously reported solutions that used the NASTRAN and ISO3DQ computer programs. The NASA TAZ-8A case exhibited no plastic strains, and the elastic and elastic-plastic analyses gave identical results. Elastic-plastic analyses of the 316 stainless steel alloy showed plastic strain reversal with a shift of the mean stresses in the compressive direction. The maximum equivalent total strain ranges for these cases were 13 to 22 percent greater than that calculated from elastic analyses.
Elastic-plastic stress-strain analyses were performed for double-edge wedge specimens subjected to thermal cycling in fluidized beds at 316 and 1088 C. Four cases involving different nickel-base alloys (IN 100, Mar M-200, NASA TAZ-8A, and Rene 80) were analyzed by using the MARC nonlinear, finite element computer program. Elastic solutions from MARC showed good agreement with previously reported solutions obtained by using the NASTRAN and ISO3DQ computer programs. Equivalent total strain ranges at the critical locations calculated by elastic analyses agreed within 3 percent with those calculated from elastic-plastic analyses. The elastic analyses always resulted in compressive mean stresses at the critical locations. However, elastic-plastic analyses showed tensile mean stresses for two of the four alloys and an increase in the compressive mean stress for the highest plastic strain case.
Forces and pressures on two nonaxisymmetric wedge nozzles were measured in a 16 foot transonic tunnel. Tests were conducted at static conditions and at free stream Mach numbers of 0.60, 0.80, 0.90, 0.94, and 1.20. The range of nozzle pressure ratios varied with configuration and Mach number. The internal and external geometry of the nozzles and the test model are defined in detail. Nozzle performance data are presented as discharge coefficients, internal thrust ratios, thrust minus nozzle drag ratios, and ideal thrust coefficients. Extensive internal and external pressure measurements are presented.
A numerical study is made of the stability of weak and strong shocks attached to wedges and cones. The stability is shown to depend on the boundary conditions imposed, in good agreement with the experimental observations and the principle of minimum entropy. The behavior of the solutions is explained by quasi-static considerations.
The possible depletion of plasma bubbles associated with the equatorial spread-F phenomenon was examined in terms of plumes mapped with the ALTAIR radar and bubbles measured by ion-drift meter on board the Explorer E satellite. The meter measured the east-west spatial relationship of ion-density depletions. The plasma bubbles were found to be vertically elongated depletions extending downward from the bottom side of the F layer in the form of tilted wedges. The electrodynamics of the bubbles correspond with observations of large eastward drift velocities of plumes comparable to the F region drift measurements. It was also determined that the west wall of large scale altitude modulations of the bottomside F layer becomes structured and evolves with the generation of secondary plumes and bubbles.
A fringe detection and measurement system was constructed for use with the CNRS Fizeau wedge laser tuner, consisting of three circuit boards. The first board is a standard Reticon RC-100 B motherboard which is used to provide the timing, video processing, and housekeeping functions required by the Reticon RL-512 G photodiode array used in the system. The sampled and held video signal from the motherboard is processed by a second, custom fabricated circuit board which contains a high speed fringe detection and locating circuit. This board includes a dc level discriminator type fringe detector, a counter circuit to determine fringe center, a pulsed laser triggering circuit, and a control circuit to operate the shutter for the He-Ne reference laser beam. The fringe center information is supplied to the third board, a commercial single board computer, which governs the data collection process and interprets the results.
Bartky's method for the numerical evluation of integrals of the complete elliptic type is modified to improve its accuracy. The resulting modified method is then applied to integrals involving complex arithmetic which map the upper half of one plane onto either the interior or exterior of round-nosed wedges. These solutions have engineering applications to such problems as the design of magnets and the flow of fluids in and around corners.
A system was developed for calibrating and precisely pointing a germanium dual-wedge scanner for a CO2 Doppler lidar from an airborne platform. The equations implemented in pointing the scanner and those in the iterative calibration program, which combines available data with estimated parameters of the scanner orientation relative to the axes of the aircraft's inertial navigation system to arrive at corrected scanner parameters are described. The effect of specific error conditions on program performance and the results of the program when used on 1981 test data are investigated.
Application of the Wedge and Strip readout system in microchannel plate detectors for the Extreme Ultraviolet Explorer and FAUST space astronomy programs is discussed. Anode designs with high resolution (greater than 600 x 600 pixels) in imaging and spectroscopy applications have been developed. Extension of these designs to larger formats (100 mm) with higher resolution (3000 x 3000 pixels) are considered. It is shown that the resolution and imaging are highly stable, and that the flat field performance is essentially limited by photon statistics. Very high speed event response has also been achieved with output pulses having durations of less than 10 nanoseconds.
EUV and far UV applications of wedge and strip anodes in photon-counting microchannel plate detector systems are discussed in light of performance data obtained as a result of EUV Explorer spacecraft open face detector and FAUST-Spacelab far UV sealed tube sensor calibrations. CsI quantum detection efficiencies of about 80 percent at 114 A and about 40 percent at 600 and 1300 A have been achieved; a position sensitivity of less than 10 microns is demonstrated, and the position resolution, image linearity, background rate, and flat-field characteristics are discussed.
Microchannel plate (MCP) detector systems that use wedge and strip anodes for imaging radiation in the range 50 A to 8000 A are described. Test data, obtained from the calibration of the Extreme Ultraviolet Explorer Satellite detectors and the ARIA EUV aeronomy sensor is presented. The long-term performance characteristics of Z-stack microchannel plates are investigated and it is shown that stable operation is achieved after an initial settling period. Conventional and new anode designs and their potential for increasing the position resolution are discussed. Position resolution of better than 80 microns FWHM has been attained for 50 mm devices, and this is shown to be essentially independent of event location. Image nonlinearity of less than 0.3 percent has been achieved with stability to better than 0.1 percent. Differential nonlinearity of less than 1 percent and stability to better than 1 percent have been obtained. Measurements of the quantum efficiency of a CsI photocathode on an MCP are presented, demonstrating efficiencies as high as 47 percent.
Results of the ratio of stress intensity factor to crack-mouth displacement as a function of crack length are presented for the wedge-loaded compact specimen. Comparisons are made between experimental compliance results, numerical results from collocation methods, and deep-crack limit-solution results. Applications are for crack-arrest and stress-corrosion-cracking tests for metals and other materials under predominantly linear elastic conditions.