Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Wall conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Prediction and control of transition in hypersonic boundary layers

In this paper, the role of compressible linear stability theory in prediction of boundary layer transition at supersonic and hypersonic speeds is investigated. Computations for sharp cones, using the e exp N method with N = 10, show that the first oblique Tollmien-Schlichting mode is responsible for transition at adiabatic wall conditions for freestream Mach numbers up to 7. For cold walls, the two-dimensional second mode dominates the transition process at lower hypersonic Mach numbers due to the well-known destabilizing effect of cooling on the second mode. It is shown that pressure gradient and suction may be used to stabilize this mode. Some results on the real gas effects on hypersonic boundary-layer stability are presented.

Malik, Mujeeb R.↗

A transition detection study using a cryogenic hot film system in the Langley 0.3-meter transonic cryogenic tunnel

A transition detection study was conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3-m TCT) using a specialized hot film system designed specifically for use in cryogenic wind tunnels. The quantitative transition location data obtained at near cryogenic conditions, 360 deg R (200K) represents the first definitive transition Reynolds numbers obtained in a cryogenic wind tunnel. The model was tested at both adiabatic and nonadiabatic wall conditions with a wall-to-total temperature ratio as low as 0.47. The test results indicated an improved technique for hot-film installation and a modified data acquisition system would allow the on-line determination of the location of boundary layer transition in cryogenic wind tunnels, such as the U.S. National Transonic Facility.

Johnson, C. B.↗

Auger electron spectroscopy study of reactor walls in transition from an O{sub 2} to a Cl{sub 2} plasma

In plasma etching processes, the reactor wall conditions can change over time due to a number of intentional and unintentional reasons, leading to a variability in the radical number densities in the plasma, caused by changes in the probabilities for reactions such as recombination at the walls. This leads to loss of reproducibility in the etching process. Here the authors isolated one such effect in which the feed gas was changed in the absence of a substrate. The transient surface composition of an anodized aluminum surface was determined for inductively coupled plasmas as the gas was switched from Cl{sub 2} to O{sub 2} and vice versa. The study was carried out with the spinning wall method and Auger electron spectroscopy. When the surface was first conditioned in an O{sub 2} plasma and then exposed to Cl{sub 2} plasmas, a rapid uptake of Cl was found in the first tens of seconds, followed by a slow approach to a steady-state value within {approx}5 min of plasma exposure. Conversely, when the surface was exposed to a Cl{sub 2} plasma for a long time and then switched to an O{sub 2} plasma, the anodized aluminum surface underwent a rapid dechlorination in the first few seconds and then a slow approach to steady state over {approx}3 min. Throughout these treatments, the coverages of Si (from erosion of the quartz discharge tube) and O were nearly constant.

36 MATERIALS SCIENCE↗

Combustion Performance and Emissions Optimization Through Integration of a Miniaturized High-Temperature Multi Process Monitoring System

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution of wall conditions in utility boilers. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of a coal-fired utility boiler in this project but can be applied to many other industries and applications as well. The new sensor design, leveraging the existing electrochemical noise-based monitoring system, is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data can be transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, five mMPMS were installed at a full-scale pulverized coal-fired plant, Basin Electric Power Cooperative’s Leland Olds Unit 1. The systems were demonstrated over a 6-week period during typical operation. Sensor measurements of deposit thickness were validated during the demonstration and subsequently leveraged to determine sensor-based boiler cleaning strategies. These strategies have the benefit of reduced thermal stresses on boiler tubes from over-cleaning and improved boiler water management. At the end of the project, continued development of the sensor technology was carried out at PacifiCorp’s Hunter Station. REI leveraged the permanent installation of the mMPMS in Unit 3 made possible by DOE funding on a separate program. The work at Hunter Plant focused on application of machine learning and artificial intelligence-based models for integration of sensor signals into control and optimization of Hunter Unit 3 processes.

42 ENGINEERING↗

High-Temperature Multi-Process Sensor Development and Demonstration at a Full-scale PC Combustion System

The main objective of this research program is to design, manufacture, and demonstrate a miniaturized, multi-process, monitoring system (mMPMS) for boiler condition management and easy system deployment to obtain a higher spatial resolution of wall conditions in utility boilers. This system will facilitate a Condition-Based Maintenance (CBM) philosophy that actively monitors the health of assets to predict and prevent failures and maximize availability and generating capacity at a reduced cost. CBM systems can provide boiler data that the advanced process control (APC) system can utilize for plant performance optimization, which is increasingly relevant as coal power plants shift from predominantly base-load operation to predominantly transient operation involving large load swings. The mMPMS is based on an electrochemical sensor that provides a real-time indication of the risk of damage to key locations in the radiant or convective section of a coal-fired boiler such as metal loss rates, heat flux, metal surface temperature, and deposit thickness. These indications can be utilized to optimize boiler performance as well as improve boiler availability in conjunction with corresponding operating conditions. This monitoring system was developed and tested in the high-temperature regions of a coal-fired utility boiler in this project but can be applied to many other industries and applications as well. The new sensor design, leveraging the existing electrochemical noise-based monitoring system, is small enough to be installed through the webbing of the waterwalls without the need for long shut-downs to bend tubes and to make it feasible to obtain high spatial resolution in the boiler. Data can be transferred to the plant distributed control system (DCS) and any other control system. The sensor body that houses the sensor assembly was designed to ensure good conductive contact with boiler tubes to ensure the sensor is held at an identical temperature to the tube surface temperature. The data acquisition and signal conditioning modules were redesigned into a small footprint with optimized cooling of the module. System software was developed specifically for the new signal conditioning module and is compatible with plant PLCs. After the preliminary testing at a pilot-scale facility, five mMPMS were installed at a full-scale pulverized coal-fired plant, Basin Electric Power Cooperative’s Leland Olds Unit 1. The systems were demonstrated over a 6-week period during typical operation. Sensor measurements of deposit thickness were validated during the demonstration and subsequently leveraged to determine sensor-based boiler cleaning strategies. These strategies have the benefit of reduced thermal stresses on boiler tubes from over-cleaning and improved boiler water management. At the end of the project, continued development of the sensor technology was carried out at PacifiCorp’s Hunter Station. REI leveraged the permanent installation of the mMPMS in Unit 3 made possible by DOE funding on a separate program. The work at Hunter Plant focused on application of machine learning and artificial intelligence-based models for integration of sensor signals into control and optimization of Hunter Unit 3 processes.

Advanced Sensors, Corrosion, Ash Deposition, Optim↗

Study on premixed combustion in cylindrical micro combustors: Transient flame behavior and wall heat flux

The micro combustor is a key component of the micro thermophotovoltaic (TPV) system. Improving the wall temperature of the micro combustor is an effective way to elevate the system efficiency. An experimental study on the wall temperature and radiation heat flux of a series of cylindrical micro combustors (with a backward-facing step) was carried out. For the micro combustors with d = 2 mm, the regime of successful ignition (under the cold wall condition) was identified for different combustor lengths. Acoustic emission was detected for some cases and the emitted sound was recorded and analyzed. Under the steady-state condition, the effects of the combustor diameter (d), combustor length (L), flow velocity (u{sub 0}) and fuel-air equivalence ratio ({phi}) on the wall temperature distribution were investigated by measuring the detailed wall temperature profiles. In the case that the micro combustor is working as an emitter, the optimum efficiency was found at {phi} {approx} 0.8, independent of the combustor dimensions (d and L) and the flow velocity. Under the experimental conditions employed in the present study, the positions of the peak wall temperature were found to be about 8-11 mm and 4-6 mm from the step for the d = 3 mm and d = 2 mm micro combustors, respectively, which are 8-11 and 8-12 times of their respective step heights. This result suggests that the backward-facing step employed in the combustor design is effective in stabilizing the flame position. (author)

30 DIRECT ENERGY CONVERSION↗

A compact solution to computational acoustics

This paper demonstrates that the linearized, dimensional Euler equations for acoustic computation can be accurately solved as a set of decoupled first-order wave equations, and that if ordered properly, this system of simple waves has unambiguous, easily implemented boundary conditions, allowing waves of same group speeds to pass through numerical boundaries or comply with wall conditions. Thus, the task of designing a complex multi-dimensional scheme with approximate far-field boundary conditions reduces to the design of higher order schemes for the one-dimensional simple wave equation. A compact finite-difference scheme and a characteristically exact but numerically n(th) order accurate boundary condition are introduced for solving the first order wave equation. Spanning a three-point two-level stencil, this low-dispersion implicit scheme has a third order spatial accuracy when used on nonuniform meshes, fourth order accurate on uniform meshes, and a temporal accuracy of second order due to the choice of trapezoidal integration for algorithmic simplicity. The robustness and accuracy of the scheme are demonstrated through a series of numerical experiments and comparisons with published results. When tested on the one-dimensional wave equation on a uniform grid, this scheme allows a Gaussian wave packet to pass through any finite domain with low numerical dispersion characteristic of a spatially fourth-order scheme and reflections at numerical boundaries maintained below truncation error. On highly stretched and irregular grids, only mild dispersions are found in the solution while solutions by other methods fail or are severely distorted. Yet, this scheme is no more sophisticated to solve or implement than the Crank-Nicolson scheme. This scheme has been tested on four categories of the ICASE/LaRC benchmark problems, which include propagation of acoustic and convective waves in Cartesian and cylindrical domains, reflection of acoustic wave at stationary/moving boundaries, and sound generation by gust-blade interaction.

Fung, K.-Y.↗

Advances in High Harmonic Fast Wave Heating of NSTX H-mode Plasmas

High-harmonic fast wave (HHFW) heating and current drive is being developed in NSTX to provide bulk electron heating and q(0) control during non-inductively sustained Hmode plasmas fuelled by deuterium neutral-beam injection (NBI). In addition, it is used to assist the plasma current ramp-up. A major modification to increase the RF power limit was made in 2009; the original end-grounded, single end-powered current straps of the 12- element array were replaced with center-grounded, double end-powered straps. Greater than 3 MW have been coupled into NBI-driven, ELMy H-mode plasmas with this upgraded antenna. Improved core HHFW heating, particularly at longer wavelengths and during low-density start-up and plasma current ramp-up, has been obtained by lowering the edge density with lithium wall conditioning, thereby moving the critical density for fast-wave propagation away from the vessel wall [1]. Significant core electron heating of NBI-fuelled H-modes has been observed for the first time over a range of launched wavelengths and H-modes can be accessed by HHFW alone. Visible and IR camera images of the antenna and divertor indicate that fast wave interactions can deposit considerable RF energy on the outboard divertor plate, especially at longer wavelengths that begin to propagate closer to the vessel walls. Edge power loss can also arise from HHFWgenerated parametric decay instabilities; edge ion heating is observed that is wavelength dependent. During plasmas where HHFW is combined with NBI, there is a significant enhancement in neutron rate, and fast-ion D-alpha (FIDA) emission measurements clearly show broadening of the fast-ion profile in the plasma core. Large edge localized modes (ELMs) have been observed immediately following the termination of RF power, whether the power turn off is programmed or due to antenna arcing. Causality has not been established but new experiments are planned and will be reported. Fast digitization of the reflected power signal indicates a much faster rise time for arcs than for ELMs. Based on this observation, an ELM/arc discrimination system is being implemented to maintain RF power during ELMs even when the reflection coefficient becomes large. This work is supported by US DOE contracts DE-AC-05-00OR22725 and DE-AC02- 09CH11466. References [1] C. K. Phillips, et al, Nuclear Fusion 10, 075015 (2009)

Ryan, Philip Michael↗

Operating The Upgraded NSTX HHFW Antenna Array In An Environment With Li-coated Surfaces

The single-feed, end-grounded straps of the NSTX 12-strap HHFW antenna array have been replaced with double-feed, center-grounded straps to reduce the voltages in the vicinity of the Faraday shield (FS) for a given strap current. The strap spacings to the FS and to the back plate were increased by 3 mm to decrease the electric fields for a given voltage. The electric fields near the FS have been roughly halved for the same strap currents, permitting a direct examination of the roles that internal fields play in determining antenna power limits in plasmas. Extensive RF/plasma conditioning of the antenna was required to remove enough of the evaporated Li deposits from prior wall conditioning to permit coupling in excess of 4 MW to L- and H-mode plasmas in 2009. Most arcs were associated with expulsion of Li from the FS/antenna frame surfaces. The center-grounded straps were less susceptible to arcing during ELMing H-mode plasmas. Reliable operation above 2 MW was difficult after the installation of the Liquid Lithium Divertor (LLD) in 2010. Li-compound 'dust' was found in the antennas after this run and is believed to have contributed to the reduced power limit.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Drag reducing outer-layer devices in rough wall turbulent boundary layers

The ability of outer-layer devices to reduce wall shear stress over a substantial streamwise distance in rough-wall turbulent boundary layers has been studied experimentally. The devices examined are a pair of thin flat ribbons placed in tandem as well as those having symmetric airfoil sections. The wall conditions examined are smooth, d- and k-type transverse-groove and sandgrain roughnesses. The wall drag is found to be reduced from the respective normal levels in all rough walls. All k-type rough walls exhibit a similar level of relative wall drag reduction which is also smaller than that in a smooth-wall. The d-type rough walls exhibit a transitional behaviour - the relative wall drag reduction drops from the smooth wall level to that of the k-type roughness with increasing roughness Reynolds number. However, the absolute reductions in the local wall shear stress are similar in both the rough and smooth walls. On the other hand, the relative reductions are lower in the rough walls because of a higher reference drag which is caused by the unique presence of a pressure component on which the devices are not as effective.

Bandyopadhyay, P. R.↗

Operating the Upgraded NSTX HHFW Antenna Array in an Environment with Li-coated Surfaces

The single-feed, end-grounded straps of the NSTX 12-strap HHFW antenna array have been replaced with double-feed, center-grounded straps to reduce the voltages in the vicinity of the Faraday shield (FS) for a given strap current. The strap spacings to the FS and to the back plate were increased by 3 mm to decrease the electric fields for a given voltage. The electric fields near the FS have been roughly halved for the same strap currents, permitting a direct examination of the roles that internal fields play in determining antenna power limits in plasmas. Extensive RF/plasma conditioning of the antenna was required to remove enough of the evaporated Li deposits from prior wall conditioning to permit coupling in excess of 4 MW to L- and H-mode plasmas in 2009. Most arcs were associated with expulsion of Li from the FS/antenna frame surfaces. The center-grounded straps were less susceptible to arcing during ELMing Hmode plasmas. Reliable operation above 2 MW was difficult after the installation of the Liquid Lithium Divertor (LLD) in 2010. Li-compound dust was found in the antennas after this run and is believed to have contributed to the reduced power limit.

RF Heating and Current Drive↗

The Role of Lithium Conditioning in Achieving High Performance, Long Pulse H-mode Discharges in the NSTX and EAST Devices

In this paper, the role of lithium wall conditioning on the achievement of high performance, long pulse discharges in the National Spherical Torus Experiment (NSTX) and the Experimental Advanced Superconducting Tokamak (EAST) is documented. Common observations include recycling reduction and elimination of ELMs. In NSTX, lithium conditioning typically resulted in ELM-free operation with impurity accumulation, which was ameliorated e.g. with pulsed 3D fields to trigger controlled ELMs. Active lithium conditioning in EAST discharges has overcome this problem, producing an ELM-free Hmode with controlled density and impurities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Overview of physics results from the ADITYA-U tokamak and future experiments

The ADITYA upgrade (ADITYA-U), a medium-sized (R 0 = 75 cm, a = 25 cm) conventional tokamak facility in India, has been consistently producing experiments findings by usingcircular and shaped-plasmas. Recognizing the plasma parameters aligning closely with the design parameters of circular limited plasmas, ADITYA-U shifted its focus toward exploring the operational regime for experimentation on saw-tooth and MHD phenomena. Moreover, ADITYA-U has made consistent advancements toward conducting preliminary plasma shaping experiments through the activation of top and bottom divertor coils utilizing hydrogen as well as deuterium fuels. Confinement is improved by a factor of ~1.5 in D 2 plasmas when compared to H 2 plasmas of ADITYA-U. Further, ADITYA-U operations emphasize preventing disruptions and runaway electrons (REs) to ensure safe operations for future fusion devices. Significant suppression of REs has been achieved in ADITYA-U with the application of pulsed localized vertical magnetic field (LVF) perturbation, thereby establishing the technique's independence from the tokamak device. The successful RE mitigation requires a critical threshold of LVF pulse magnitude, which is approximately 1% of the toroidal magnetic field, and a minimum duration of ~5 ms. Apart from this, several novel findings have been achieved in the ADITYA-U experiments, including the modification of sawtooth duration through gas-puff, the emergence of MHD-induced geodesic acoustic mode-like oscillations, the propagation of fast heat pulses induced by MHD activity, the control of RE dynamics through Gas-puffs, the propagation of pinch-driven cold-pulses, the transport and core accumulations of argon impurities, the mass dependency of plasma toroidal rotation and the detection of 'RICE' scaling, as well as the characterization of edge plasma using wall conditioning methods, such as glow discharge cleaning using a combination of Ar-H 2 mixture, localized wall cleaning by electron cyclotron resonant plasma, and the development of machine learning-based disruption predictions, will be discussed in this paper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advances in plasma–wall interaction control for H-mode operation over 100 s with ITER-like tungsten divertor on EAST

A total power injection up to 0.3 GJ has been achieved in EAST long pulse H-mode operation of 101.2 s with an ITER-like water-cooled tungsten (W) mono-block divertor, which has steady-state power exhaust capability of 10 MWm –2 . The peak temperature of W target saturated at 12 s to the value T ~ 500 °C with a heat flux ~3.3 MW m –2 being maintained during the discharge. By tailoring the 3D divertor plasma footprint through edge magnetic topology change, the heat load was broadly dispersed and thus peak heat flux and W sputtering were well controlled. Active feedback control of H-mode detachment with D 2 fuelling or divertor impurity seeding has been achieved successfully, with excellent compatibility with the core plasma performance. Active feedback control of radiative power utilizing neon seeding was achieved with f rad = 18%–41% in H-mode operation, exhibiting potential for heat flux reduction with divertor and edge radiation. This has been further demonstrated in DIII-D high β P H-mode scenario within the joint DIII-D/EAST experiment using impurity seeding from the divertor volume. Steady-state particle control and impurity exhaust has been achieved for long pulse H-mode operation over 100 s with the W divertor by leveraging the effect of drifts and optimized divertor configuration, coupled with strong pumping and extensive wall conditioning. Methods toward the reduction of divertor W sourcing, which is of crucial importance for a metal-wall tokamak, are also explored. These advances provide vital experimental information on favourable core-edge integration for high power, long-pulse H-mode operation in EAST, ITER and CFETR.

43 PARTICLE ACCELERATORS↗

Thermal Stability of RP-2 for Hydrocarbon Boost Regenerative Cooling

A series of tests were performed in the NASA Glenn Research Centers Heated Tube Facility to study the heat transfer and thermal stability behavior of RP-2 under conditions similar to those found in rocket engine cooling channels. It has long been known that hydrocarbon fuels, such as RP-2, can decompose at high temperature to form deposits (coke) which can adversely impact rocket engine cooling channel performance. The heated tube facility provides a simple means to study these effects. Using resistively heated copper tubes in a vacuum chamber, flowing RP-2 was heated to explore thermal effects at a range of test conditions. Wall temperature (850-1050F) and bulk fluid temperature (300-500F) were varied to define thermal decomposition and stability at each condition. Flow velocity and pressure were fixed at 75 fts and 1000 psia, respectively. Additionally, five different batches of RP-2 were tested at identical conditions to examine any thermal stability differences resulting from batch to batch compositional variation. Among these tests was one with a potential coke reducing additive known as 1,2,3,4-Tetrahydroquinoline (THQ). While copper tubes were used for the majority of tests, two exploratory tests were performed with a copper alloy known as GRCop-42. Each tube was instrumented with 15 thermocouples to examine the temperature profile, and carbon deposition at each thermocouple location was determined post-test in an oxidation furnace. In many tests, intermittent local temperature increases were observed visually and in the thermocouple data. These hot spots did not appear to correspond with a higher carbon deposition.

Kleinhenz, Julie E.↗

Prediction of nozzle wall pressure distribution and its application to flow over roughened surfaces

The results from a computer program which predicts two-dimensional inviscid flow in a converging-diverging nozzle are presented. The pressure drops are in excellent agreement with experimental values. The free stream wall conditions are used to present experimental heat transfer values in terms of the Stanton number for nozzle flow for both artificially-roughened and smooth wall surfaces.

Mckillop, A. A.↗

An experimental investigation of wall boundary layer transition Reynolds numbers in an expansion tube

Experimental measurements of boundary-layer transition in an expansion-tube test-gas flow are presented along with radial distributions of pitot pressure. An integral method for calculating constant Reynolds number lines for an expansion-tube flow is introduced. Comparison of experimental data and constant Reynolds number calculations has shown that for given conditions, wall boundary-layer transition occurs at a constant Reynolds number in an expansion-tube flow. Operating conditions in the expansion tube were chosen so that the effects of test-gas nonequilibrium on boundary-layer transition could be studied.

Weilmuenster, K. J.↗