Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRIBOLOGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Tribological Tuft Testing Candidate Brush Seal Materials

This paper presents a tribological tuft test method of candidate brush seal materials in viewgraph form. The goals of the research are: 1) To develop test method to tribologically brush seal materials; 2) To evaluate materials to identify potential improvements and trends; and 3) Guide seal material development and selection.

DellaCorte, Chris↗

Preventing Spacecraft Failures Due to Tribological Problems

Many mechanical failures that occur on spacecraft are caused by tribological problems. This publication presents a study that was conducted by the author on various preventatives, analyses, controls and tests (PACTs) that could be used to prevent spacecraft mechanical system failure. A matrix is presented in the paper that plots tribology failure modes versus various PACTs that should be performed before a spacecraft is launched in order to insure success. A strawman matrix was constructed by the author and then was sent out to industry and government spacecraft designers, scientists and builders of spacecraft for their input. The final matrix is the result of their input. In addition to the matrix, this publication describes the various PACTs that can be performed and some fundamental knowledge on the correct usage of lubricants for spacecraft applications. Even though the work was done specifically to prevent spacecraft failures the basic methodology can be applied to other mechanical system areas.

Fusaro, Robert L.↗

Evaluation of Vapor Pressure and Ultra-High Vacuum Tribological Properties of Ionic Liquids (2) Mixtures and Additives

Ionic liquids are salts, many of which are typically viscous fluids at room temperature. The fluids are characterized by negligible vapor pressures under ambient conditions. These properties have led us to study the effectiveness of ionic liquids containing both organic cations and anions for use as space lubricants. In the previous paper we have measured the vapor pressure and some tribological properties of two distinct ionic liquids under simulated space conditions. In this paper we will present vapor pressure measurements for two new ionic liquids and friction coefficient data for boundary lubrication conditions in a spiral orbit tribometer using stainless steel tribocouples. In addition we present the first tribological data on mixed ionic liquids and an ionic liquid additive. Post mortem infrared and Raman analysis of the balls and races indicates the major degradation pathway for these two organic ionic liquids is similar to those of other carbon based lubricants, i.e. deterioration of the organic structure into amorphous graphitic carbon. The coefficients of friction and lifetimes of these lubricants are comparable to or exceed these properties for several commonly used space oils.

Morales, Wilfredo↗

Ni-Ti Alloys for Tribological Applications: The Effects of Serendipity on Research and Development

Novel superelastic materials based upon Nickel-Titanium (NiTi) alloys are an emerging technology that almost escaped recognition. Though steel is the dominant material of choice for mechanical components (bearings and gears) it has intrinsic limitations related to corrosion and plastic deformation. In 2004, at the request of a small manufacturing firm, Nitinol 60 was assessed as an alternative to bearing steel. Early investigations showed it to be hard and impervious to aqueous corrosion but its tribological properties were not fully explored. Conventional wisdom in the field of tribology suggests that alloys rich in titanium are poor candidate bearing materials but NiTi, an intermetallic, demonstrates that such thinking can be and often is, wrong. Though early stage tests reveal acceptable friction and wear behavior, extensive materials engineering and processing development was essential in producing the precision microstructures needed for long-life bearings and gears. In the course of exploring this new material system other game-changing and unexpected properties, such as superelastic resilience, were observed. Today, the aerospace community is exploiting the unique characteristics of the NiTi alloy materials to solve problems on earth, underwater and in space. A fortunate decision to acknowledge a single industrial request turned out to be the key to an entirely new technology.

engineering↗

Tribological synthesis method for producing low-friction surface film coating

An article of method of manufacture of a low friction tribological film on a substrate. The article includes a substrate of a steel or ceramic which has been tribologically processed with a lubricant containing selected additives and the additives, temperature, load and time of processing can be selectively controlled to bias formation of a film on the substrate where the film is an amorphous structure exhibiting highly advantageous low friction properties.

36 MATERIALS SCIENCE↗

Mechanical and Tribological Behavior of ZrB{sub 2}-TiB{sub 2} System Prepared by Mechanical Activation Spark Plasma Sintering Technique

ZrB{sub 2}-TiB{sub 2} system among varying amount of TiB{sub 2} loading (5, 10, 15, 20 and 30 wt.%) was prepared by mechanical activation spark plasma sintering at 2100 °C for 15-min dwell time under 50 MPa uniaxial pressure in argon atmosphere. The effect of the TiB{sub 2} loading on properties like physical, mechanical and tribological of the prepared samples was studied and evaluated with monolithic ZrB{sub 2} ceramic. Finally, almost fully dense samples (> 96% of theoretical density) were fabricated. Microstructural observation and XRD phase analysis of sintered compact revealed that TiB{sub 2} completely went into the ZrB{sub 2} structure by formation of solid solution with ZrB{sub 2} phase. ZrB{sub 2}-TiB{sub 2} (30 wt.%) showed the highest Vickers micro-hardness (H{sub V}) of 20.64 GPa at 10 N load. On addition of TiB{sub 2}, the fracture toughness of the ZrB{sub 2}-TiB{sub 2} improved up to 4.69 ± 0.43 MPa m{sup 1/2} over monolithic ZrB{sub 2} at 10 N load. At 10 N load, the scratch resistance coefficient, wear rate and wear resistance coefficient of ZrB{sub 2}-TiB{sub 2} (30 wt.%) reached a lowest value of 0.32, 0.35 mm{sup 3}/N m and 0.008, respectively, at 10 N load than other ZrB{sub 2} compositions.

36 MATERIALS SCIENCE↗

Tribological behaviors of nanotwinned Al alloys

Wear-induced damages cause significant materials loss each year. Al alloys are widely used by industry but usually have low wear resistance. Here, we compare the tribological behaviors of ultrafine grained Al, a nanoprecipitate hardened Al 7075 alloy and nanotwinned Al–Ni alloys using the nanoscratch. The nanotwinned Al–Ni alloys exhibit lower coefficient of friction and much greater wear resistance than the Al and Al 7075 alloys. Additionally, the enhanced wear properties of Al–Ni alloys arise from their high strength and the evolution of nanotwinned microstructures into gradient nanograins during wear. These findings on fundamental wear mechanisms in nanotwinned alloys may advance the discovery of wear-resistant metallic materials.

36 MATERIALS SCIENCE↗

Cryo-quenched Fe–Ni–Cr alloy decorative steel single crystals II: Alloy phases, structure, hardness, tensile, tribological, magnetic and electronic properties

We have previously reported (Boatner et al., J. Alloys Compd. 691 (2017) 666–671) on the discovery, formation, processing, and application of a new decorative ternary steel alloy and on its use in a wide range of practical applications including: custom and commercial knives, art objects, jewelry, electronics, and furniture. This decorative property results when polished single crystals of the 70 wt%Fe-15 wt%Ni-15 wt% Cr austenitic alloy are cryo-quenched into the martensitic phase resulting in the formation of a three-dimensional raised pattern of mixed austenitic/martensitic laths. These laths propagate across large dimensions of the material due to the absence of grain boundaries in the single crystal. The macroscopic optically reflective 3-D decorative pattern reproduces the structural symmetry inherent in the single-crystal orientation. This pattern results solely from the metallurgical phase properties of the ternary alloy and is completely distinct from the properties of Damascus steels or more modern so-called pattern-welded steels. Here we use X-ray diffraction, nanoindentation, hardness measurements/scratch testing, tribological measurements, and alloy resistivity and magnetization methods to obtain a more fundamental and comprehensive study of the effects of the austenitic/martensitic phase transition on the structural and physical properties of the 70 wt%Fe-15 wt%Ni-15 wt% Cr alloy. These results reveal new insight into irreversible phenomena that are associated with the inhibited phase transition on heating of the two-phase, mixed austenitic/martensitic structure that is formed subsequent to cryo-quenching the alloy crystal to 77 K.

36 MATERIALS SCIENCE↗

Microstructures and tribological properties of laser cladded Ti-based metallic glass composite coatings

Metallic glass composite coatings Ti{sub 45}Cu{sub 41}Ni{sub 9}Zr{sub 5} and Ti{sub 45}Cu{sub 41}Ni{sub 6}Zr{sub 5}Sn{sub 3} (at.%) on a Ti-30Nb-5Ta-7Zr (wt.%) (TNTZ) alloy were prepared by laser cladding. The microstructures of the coatings were characterized by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM) equipped with energy dispersive X-ray analyzer (EDXA), and transmission electron microscopy (TEM). Results indicated that the coatings have an amorphous structure embedded with a few nanocrystalline phases and dendrites. A partial substitution of Ni by Sn can improve the glass forming ability of Ti-base metallic glass system, and induce the formation of nano-sized Ni{sub 2}SnTi phase during the cyclic laser heating. The tribological behavior of both the substrate and the coatings was investigated in detail. A significant improvement in both the hardness and the wear resistance of the coatings was achieved with the addition of Sn. The relationship between the wear resistance and the microstructures of the coatings was discussed. - Highlights: •Ti-based metallic glass composite coatings were prepared by laser cladding. •The wear resistance is greatly improved by laser cladding of composite coatings. •Substitution of Ni by Sn increases GFA and wear resistance of the coatings. •A good balance of crystalline/amorphous phases improves the wear resistance. •Adhesive wear serves as the dominant wear mechanism of the composite coatings.

36 MATERIALS SCIENCE↗

Tribology of two-dimensional materials: From mechanisms to modulating strategies

Two-dimensional (2D) materials are crystalline materials made of a single or a few layers of atoms. They have been an active research subject in recent years because of their unique physical and chemical properties. In particular, 2D materials such as graphene, hexagonal BN, and MoS 2 exhibit some of the lowest friction coefficients and wear rates, making them attractive for enhancing the efficiency, durability, and environmental compatibility of future mechanical systems. This review will focus on recent advances in the tribology of 2D materials. Starting from general physical characteristics, the essential friction and wear behavior of 2D materials together with the associated mechanisms are reviewed for both interlayer and surface sliding. Influences of the atomic structures of the slip interfaces and environmental factors are discussed, with special attention given to various strategies for achieving friction modulation and superlubricity. Finally, the emerging engineering applications of 2D materials, as well as future prospects, are summarized.

36 MATERIALS SCIENCE↗

Applications of tribology to determine attrition by wear of particulate solids in CFB systems

In recent years, much attention has been focused on the development of novel technologies for carbon capture and chemicals production that utilize a circulating fluidized bed (CFB) configuration; examples include chemical looping combustion and circulation of temperature swing adsorbents in a CFB configuration for CO 2 capture. A major uncertainty in determining the economic feasibility of these technologies is the required solids makeup rate, which, among other factors, is due to impact and wear attrition at various locations, including standpipes, cyclones, and the gas jets in fluid beds. While correlations have been developed that estimate the attrition rates at these areas, these correlations are dependent on constants that are uncertain without extensive experiment in the corresponding unit operation. Thus, it is difficult to determine the attrition rate a priori without performing extensive experiments on the materials or scaling up entirely. In this work, the authors outline a methodology for predictive attrition based on fundamental material properties from fields of tribology—specifically, the study of wear—to the knowledge of forces and sliding distances determined from hydrodynamic models to develop basic attrition models for novel CFB systems. The equations are derived for the standpipe and cyclone, which are common components found in CFBs, and the cyclone equation is compared to experimental data of attrition in the literature. The cyclone equation derived in this work results in an abrasion rate based on (1) material properties such as particle density and hardness, (2) inlet velocity, and (3) cyclone geometry. According to this equation, increasing the diameter of the cyclone and the solids inlet velocity tends to increase the rate of abrasion of the catalyst, while decreasing the hardness increases the abrasion rate. The functionality of the increasing attrition rate with velocity increase implies that increasing the efficiency of the cyclone may also increase the attrition rate via abrasion. With modifications to the severity coefficient term to include the solids loading, the cyclone equation derived in this work fits data from Reppenhagen and Werther with a coefficient of determination (R2) of 92%.

01 COAL, LIGNITE, AND PEAT↗

Elevated-Temperature Tribology of Metallic Materials

The wear of metals and alloys takes place in many forms, and the type of wear that dominates in each instance is influenced by the mechanics of contact, material properties, the interfacial temperature, and the surrounding environment. The control of elevated-temperature friction and wear is important for applications like internal combustion engines, aerospace propulsion systems, and metalworking equipment. The progression of interacting, often synergistic processes produces surface deformation, subsurface damage accumulation, the formation of tribolayers, and the creation of free particles. Reaction products, particularly oxides, play a primary role in debris formation and microstructural evolution. Chemical reactions are known to be influenced by the energetic state of the exposed surfaces, and that surface energy is in turn affected by localized deformation and fracture. At relatively low temperatures, work-hardening can occur beneath tribo-contacts, but exposure to high temperatures can modify the resultant defect density and grain structure to affect the mechanisms of re-oxidation. As research by others has shown, the rate of wear at elevated temperatures can either be enhanced or reduced, depending on contact conditions and nature of oxide layer formation. Furthermore, the thermodynamic driving force for certain chemical reactions is moderated by kinetics and microstructure. The role of deformation, oxidation, and tribo-corrosion in the elevated temperature tribology of metallic alloys will be exemplified by three examples involving sliding wear, single-point abrasion, and repetitive impact plus slip.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Elevated temperature tribology of Ni alloys under helium environment for nuclear reactor applications

The current study investigates the friction and wear behavior of two primary candidate materials, Inconel 617 and alloy 800HT for high-temperature gas cooled nuclear reactors/very-high-temperature reactors. Using a custom-built high temperature tribometer, helium cooled reactor environment was simulated at room and 800 °C temperatures. Microscopy and chemical analyses were carried out to explain the tribological performance of the alloys. At elevated temperatures, both alloys show higher friction in helium, compared to air environment. Both alloys exhibit high wear resistance in all experimental conditions, except at high temperature helium environment. In conclusion, the formation of glazed and mechanically mixed layers of oxides were found to be important causes for the lower friction and wear in high temperature air atmosphere.

36 MATERIALS SCIENCE↗

Effect of friction stir processing on the tribological performance of high carbon steel.

Friction stir processing (FSP) was applied to 1080 carbon steel as a means to enhance the near-surface material properties. The process transformed the original pearlite microstructure to martensite, resulting in significant increase in surface hardness. This surface hardening produced a significant benefit for friction and wear behavior of the steel as measured by unidirectional sliding ball-on-flat testing. Under dry sliding, FSP reduced friction coefficient by approximately 25% and wear rate by an order of magnitude. Under oil lubrication, FSP had only a marginal effect on friction, but it reduced wear rates by a factor of 4. The improvement in tribological performance of 1080 steel by FSP technique is attributed to reduced plasticity of the near-surface material during sliding contact

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Tribology of incoloy 800HT for nuclear reactors under helium environment at elevated temperatures

Nickel-based alloy 800HT is considered one of the main candidate alloys for nuclear reactors with gas cooled high-temperature environment and, therefore, it is necessary to have a thorough understanding of the alloy tribological response for obtaining optimum operating and loading conditions. The current study investigated the wear and friction behavior of alloy 800HT using a customized high temperature tribometer to simulate the environment of helium cooled reactor up to 750 °C. The effect of temperature, contact load, environment, sliding distance and sliding speed on the alloy friction and wear were studied. To generalize the study for other applications, an investigation is also performed in air environment. The friction and wear coefficients have the highest values at high temperature helium atmosphere where the formation and stability of the oxide scales play an important role. Optical and contact profiling, scanning electron microscopy, as well as energy dispersive spectroscopy techniques were utilized to study the surface oxide. The analysis showed the presence of Fe-Cr-Ni rich oxide both in air and helium. Finally, the protective glazed layer did not form in helium in any condition, whereas in air and under specific conditions a stable protective oxide layer was observed.

36 MATERIALS SCIENCE↗

Tribological Testing of Anti-Adhesive coatings for Cold Rolling Mill Rolls--Application to TiN-Coated Rolls

Roll life is a major issue in cold strip rolling. Roll wear may result either in too low roll roughness, bringing friction below the minimum requested for strip entrainment; or it may degrade strip surface quality. On the contrary, adhesive wear and transfer (''roll coating'', ''pick up'') may form a thick metallic deposits on the roll which increases friction excessively and degrades strip surface again [1]. The roll surface, with the help of a materials-adapted lubricant, must therefore possess anti-wear and anti-adhesive properties. Thus, High Speed Steeel (HSS) rolls show superior properties compared with standard Cr-steel rolls due to their high carbide surface coverage. Another way to improve wear and adhesion properties of surfaces is to apply hard metallic (hard-Cr) or ceramic coatings. Chromium is renowned for its excellent anti-wear and anti-adhesive properties and may serve as a reference. Here, as a first step towards alternative, optimised coatings, a PVD TiN coating has been deposited on tool steels, as previous attempts have proved TiN to be rather successful in cold rolling experiments [2,3]. Different tribological tests are reported here, giving insight in both anti-adhesive properties and fatigue life improvement.

36 MATERIALS SCIENCE↗

Electron microscopic evidence for a tribologically induced phase transformation as the origin of wear in diamond

Tribological testing of a coarse-grained diamond layer, deposited by plasma-enhanced chemical vapor deposition, was performed on a ring-on-ring tribometer with a diamond counterpart. The origin of the wear of diamond and of the low friction coefficient of 0.15 was studied by analyzing the microstructure of worn and unworn regions by transmission and scanning electron microscopy. In the worn regions, the formation of an amorphous carbon layer with a thickness below 100 nm is observed. Electron energy loss spectroscopy of the C-K ionization edge reveals the transition from sp{sup 3}-hybridized C-atoms in crystalline diamond to a high fraction of sp{sup 2}-hybridized C-atoms in the tribo-induced amorphous C-layer within a transition region of less than 5 nm thickness. The mechanically induced phase transformation from diamond to the amorphous phase is found to be highly anisotropic which is clearly seen at a grain boundary, where the thickness of the amorphous layer above the two differently oriented grains abruptly changes.

36 MATERIALS SCIENCE↗

Effect of gas ratio on tribological properties of sputter deposited TiN coatings

Titanium nitride (TiN) coatings were deposited on Si, corning glass, pins of mild steel (MS, ϕ3mm), aluminium (Al, ϕ4mm) and brass (ϕ6mm) substratesby DC magnetron sputtering. The argon and nitrogen (Ar:N{sub 2})gas ratio was precisely controlled by Mass Flow Controller (MFC) and was varied systematically at diffract values of 10:10,12:08, 16:04 and 18:02sccm. The structural properties of TiN coatings were characterized by X-ray diffraction (XRD) and its surface topography was studied using field emission scanning electron microscopy (FE-SEM). The tribological properties of TiN coatings were investigated using pin-on-disc tribometer.

36 MATERIALS SCIENCE↗