Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Simplified Simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

MCC level C formulation requirements. Shuttle TAEM guidance and flight control, STS-1 baseline

The TAEM guidance and body rotational dynamics models required for the MCC simulation of the TAEM mission phase are defined. This simulation begins at the end of the entry phase and terminates at TAEM autoland interface. The logic presented is the required configuration for the first shuttle orbital flight (STS-1). The TAEM guidance is simulated in detail. The rotational dynamics simulation is a simplified model that assumes that the commanded rotational rates can be achieved in the integration interval. Thus, the rotational dynamics simulation is essentially a simulation of the autopilot commanded rates and integration of these rates to determine orbiter attitude. The rotational dynamics simulation also includes a simulation of the speedbrake deflection. The body flap and elevon deflections are computed in the orbiter aerodynamic simulation.

Carman, G. L.↗
DOE OSTI2021

Updated Thermofluid Performance of the Simplified Flat Variant of the HEMJ

Our group has recently developed and studied “finger”-type divertors that are a simplified version of the helium-cooled modular divertor with multiple jets (HEMJ) using coupled computational fluid dynamics and thermal stress simulations. Such a simplified geometry could reduce complexity and cost given the large number of fingers required to cover the total divertor target area. Previous experimental studies for this simplified flat design reported lower heat transfer coefficients and higher pressure drops than the HEMJ, contrary to numerical predictions. Subsequent measurements determined that the original test section had significant dimensional variations in the jet exit holes. A new test section was therefore manufactured and tested in the Georgia Tech (GT) helium loop. The experimental results presented here for this test section at maximum heat flux of 7.1 MW/m 2 are in good agreement with numerical predictions. Correlations developed from these experimental data are extrapolated to predict the maximum heat flux that can be accommodated by the flat design and the coolant pumping power requirements under prototypical conditions. Lastly, numerical simulations are used to estimate the sensitivity of the flat design to geometric variations typical of manufacturing tolerances and variations in the gap width.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRSDate not supplied

Seamless Integration of Multibody and Orbital Dynamics to Support Human Spaceflight Simulations

At the NASA Johnson Space Center (JSC), modeling capability requirements are often driven by the need to simulate upcoming mission scenarios for analysis, procedures development, and training. In preparation for free-flyer vehicle capture, maneuvers, and release, it was determined that the multibody dynamics capabilities provided by MBDyn and the orbital dynamics capabilities supplied by JEOD needed to be merged to properly simulate the dynamic behaviors expected on-orbit. After initial attempts to combine the two packages proved cumbersome, it was decided that a more refined solution was required to facilitate the interface between these two packages. The resulting interface software package was named MBJEOD. The primary design goals for this new package were to leave MBDyn and JEOD untouched, to simplify and clarify simulation initialization for users, and to support any topology or on-orbit operational scenario that future missions might require. This paper provides a detailed overview of MBJEOD and the approach taken to seamlessly integrate the multibody dynamics of MBDyn with the orbital dynamics of JEOD. Additional attention is given to the numerical considerations required for MBJEOD and the simplifying assumptions leveraged to provide for real-time simulation needs. Verification and validation are addressed and current MBJEOD applications at the NASA JSC are discussed.

modeling↗
NASA NTRSDate not supplied

Seamless Integration of Multibody and Orbital Dynamics to Support Human Spaceflight Simulations

At the NASA Johnson Space Center (JSC), modeling capability requirements are often driven by the need to simulate upcoming mission scenarios for analysis, procedures development, and training. In preparation for free-flyer vehicle capture, maneuvers, and release, it was determined that the multibody dynamics capabilities provided by MBDyn and the orbital dynamics capabilities supplied by JEOD needed to be merged to properly simulate the dynamic behaviors expected on-orbit. After initial attempts to combine the two packages proved cumbersome, it was decided that a more refined solution was required to facilitate the interface between these two packages. The resulting interface software package was named MBJEOD. The primary design goals for this new package were to leave MBDyn and JEOD untouched, to simplify and clarify simulation initialization for users, and to support any topology or on-orbit operational scenario that future missions might require. This paper provides a detailed overview of MBJEOD and the approach taken to seamlessly integrate the multibody dynamics of MBDyn with the orbital dynamics of JEOD. Additional attention is given to the numerical considerations required for MBJEOD and the simplifying assumptions leveraged to provide for real-time simulation needs. Verification and validation are addressed and current MBJEOD applications at the NASA JSC are discussed.

modeling↗
NASA NTRS2010

Thermal Protection System Cavity Heating for Simplified and Actual Geometries Using Computational Fluid Dynamics Simulations with Unstructured Grids

Thermal Protection System (TPS) Cavity Heating is predicted using Computational Fluid Dynamics (CFD) on unstructured grids for both simplified cavities and actual cavity geometries. Validation was performed using comparisons to wind tunnel experimental results and CFD predictions using structured grids. Full-scale predictions were made for simplified and actual geometry configurations on the Space Shuttle Orbiter in a mission support timeframe.

McCloud, Peter L.↗
DOE OSTI2021

Validation of the EDGES Low-band Antenna Beam Model

The response of the antenna is a source of uncertainty in measurements with the Experiment to Detect the Global Epoch of Reionization Signature (EDGES). We aim to validate the electromagnetic beam model of the low-band (50–100 MHz) dipole antenna with comparisons between models and against data. We find that simulations of a simplified model of the antenna over an infinite perfectly conducting ground plane are, with one exception, robust to changes in the numerical electromagnetic solver code or algorithm. For simulations of the antenna with the actual finite ground plane and realistic soil properties, we find that two out of three numerical solvers agree well. Applying our analysis pipeline to a simulated drift-scan observation from an early EDGES low-band instrument that had a 10 m × 10 m ground plane, we find residual levels after fitting and removing a five-term foreground model from the simulated data binned in local sidereal time (LST) average about 250 mK with ±40 mK variation between numerical solvers. A similar analysis of the primary 30 m × 30 m sawtooth ground plane reduced the LST-averaged residuals to about 90 mK with ±10 mK between the two viable solvers. More broadly we show that larger ground planes generally perform better than smaller ground planes. Simulated data have a power that is within 4% of real observations, a limitation of net accuracy of the sky and beam models. We observe that residual spectral structures after foreground model fits match qualitatively between simulated data and observations, suggesting that the frequency dependence of the beam is reasonably represented by the models. We find that a soil conductivity of 0.02 S m{sup -1} and relative permittivity of 3.5 yield good agreement between simulated spectra and observations. This is consistent with the soil properties reported by Sutinjo et al. for the Murchison Radio-astronomy Observatory, where EDGES is located.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1981

V/STOL propulsion control technology

Results of a NASA sponsored study of V/STOL Propulsion Control Analysis are presented. The study involved propulsion control requirements, design concepts and procedures, and control designs for supersonic V/STOL. A variable cycle engine with a remote augmented lift system was used as a basis for establishing typical operating requirements and control concepts, and a nonlinear engine model was developed for control development as a precursor to a real-time simulation capability. A simplified aircraft model was also used to investigate transition requirements, and a long-range technology plan was developed to define subsequent program requirements for achieving a real-time piloted simulation capability.

Brown, H.↗
NASA NTRS1972

A simplified correlation technique for position location using earth satellites.

To derive range to a moving vehicle for surveillance and navigation purposes, the phase delays in sets of sinusoidal tones may be measured using synchronous satellites for signal relay. When the number of users is large, problems of rapid acquisition and measurement occur in multiple-access systems. This paper describes the selection and processing of an orthogonal tone set which has several useful features. The paper also presents a simulation of a simplified digital technique for the noise-free case, as well as for a composite signal buried in wideband noise. The digital simulation is also modified to include the proposed 'hard limiting' or clipping technique.

Martin, S. C.↗
DOE OSTI2025

Challenges of standard halo models in constraining galaxy properties from cosmic infrared background anisotropies

The halo model, combined with halo occupation distribution (HOD) prescriptions, is widely used to interpret cosmic infrared background (CIB) anisotropies and extract physical information about star-forming galaxies and their connection to large-scale structures. Recent CIB-specific implementations of the halo model have adopted more physical parameterizations. However, the extent to which these models can reliably recover meaningful physical parameters remains uncertain. We assessed whether the current parameterization of CIB halo models is sufficient to recover astrophysical quantities, such as star formation efficiency, η(M h , z), and halo mass at which the peak of star formation efficiency occurs, M max , when fit to mock data. We also assessed whether discrepancies arise from assumptions about galaxy emission (the HOD ingredients) or from more fundamental components in the halo model, such as bias and matter clustering. We fit the M21 CIB HOD model, implemented within the halo model framework, to mock CIB power spectra and star formation rate density (SFRD) data generated from the SIDES-Uchuu simulation, and compared the best-fit parameters to the known simulation inputs. We then repeated the analysis using a simplified version of the simulation (SSU), explicitly designed to match the HOD assumptions. A detailed comparison of model and simulation outputs was carried out to trace the origin of observed discrepancies. While the M21 HOD model provides a good fit to the mock data, it failed to recover the intrinsic parameters accurately, particularly the halo mass at which star formation efficiency peaks. This mismatch persists even when fitting data generated with the same model assumptions. We find strong agreement (within 5%) in the emission-related components (SFRD, emissivity), but observe a scale- and redshift-dependent offset exceeding 20% in the two-halo term of the CIB power spectrum. This likely arises from limitations in the treatment of halo bias and matter clustering within the linear approximation. Additionally, incorporating scatter in the SFR–halo mass relation and the spectral energy distribution (SED) templates significantly affects the shot noise (∼50%), but has only a modest impact (less than 10%) on the clustered component. These results suggest that recovering physical parameters from CIB clustering requires improvements to the cosmological ingredients of the halo model framework, such as adopting scale-dependent halo bias and nonlinear matter power spectra in addition to careful modeling of emission physics.

cosmic background radiation↗
DOE OSTI2020

Improving Time Step Convergence in an Atmosphere Model With Simplified Physics: The Impacts of Closure Assumption and Process Coupling

Convergence testing is a common practice in the development of dynamical cores of atmospheric models but is not as often exercised for the parameterization of sub-grid physics. An earlier study revealed that the stratiform cloud parameterizations in several predecessors of the Energy Exascale Earth System Model (E3SM) showed strong time-step sensitivity and slower-than-expected convergence when the model's time step was systematically refined. In this work, a simplified atmosphere model is configured that consists of the spectral-element dynamical core of the E3SM atmosphere model coupled with a large-scale condensation parameterization based on commonly used assumptions. This simplified model also resembles E3SM and its predecessors in the numerical implementation of process coupling and shows poor time-step convergence in short ensemble tests. We present a formal error analysis to reveal the expected time-step convergence rate and the conditions for obtaining such convergence. Numerical experiments are conducted to investigate the root causes of convergence problems. We show that revisions in the process coupling and closure assumption help to improve convergence in short simulations using the simplified model; the same revisions applied to a full atmosphere model lead to significant changes in the simulated long-term climate. This work demonstrates that causes of convergence issues in atmospheric simulations can be understood by combining analyses from physical and mathematical perspectives. Addressing convergence issues can help to obtain a discrete model that is more consistent with the intended representation of the physical phenomena.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Numerical simulation of parametric resonance in point absorbers using a simplified model

Abstract Parametric resonance is a non‐linear phenomenon in which a system can oscillate at a frequency different from its exciting frequency. Some wave energy converters are prone to this phenomenon, which is usually detrimental to their performance. Here, a computationally efficient way of simulating parametric resonance in point absorbers is presented. The model is based on linear potential theory, so the wave forces are evaluated at the mean position of the body. However, the first‐order variation of the body's centres of gravity and buoyancy is taken into account. This gives essentially the same result as a more rigorous approach of keeping terms in the equation of motion up to second order in the body motions. The only difference from a linear model is the presence of non‐zero off‐diagonal elements in the mass matrix. The model is benchmarked against state‐of‐the‐art non‐linear Froude–Krylov and computational fluid dynamics models for free decay, regular wave, and focused wave group cases. It is shown that the simplified model is able to simulate parametric resonance in pitch to a reasonable accuracy even though no non‐linear wave forces are included. The simulation speed on a standard computer is up to two orders of magnitude faster than real time.

16 TIDAL AND WAVE POWER↗
NASA NTRS1993

Precession and circularization of elliptical space-tether motion

In this paper, we present a simplified analytic model for predicting motion of long space tethers. The perturbation model developed here addresses skip rope motion, where each end of the tether is held in place and the middle of the tether swings with a motion similar to that of a child's skip rope. If the motion of the tether midpoint is elliptical rather than circular, precession of the ellipse complicates the procedures required to damp this motion. The simplified analytic model developed in this paper parametrically predicts the precession of elliptical skip rope motion. Furthermore, the model shows that elliptic skip rope motion will circularize when damping is present in the longitudinal direction. Compared with high-fidelity simulation results, this simplified model provides excellent predictions of these phenomena.

Chapel, Jim D.↗
DOE OSTI2025

Improved internal short circuit models for thermal runaway simulations in lithium-ion batteries

Thermal runaway (TR) modeling is one of the primary tools that can be used to overcome challenges associated with lithium-ion battery (LIB) safety. Among all LIB accidents that have occurred over the past decade, Internal Short Circuit (ISC) remains the most common trigger mechanism. Many available models in the literature either use a simplified approach to simulate ISC or completely ignore its contribution. The aim of this study is to understand the nature of the heat released for different types of ISC scenarios, including aluminum-anode, anode–cathode, and copper-cathode ISC. We study ISC behavior using a coupled electrochemical–thermal model with an integrated TR chemical kinetics solver built in the COMSOL Multiphysics framework. The time duration of heat release and the magnitude of the peak ISC current are studied as functions of parameters such as the size of the penetrating filament and the capacity of the cell. The numerical results are used to build an empirical model validated against the published experimental TR propagation data. Our model can be successfully used as a viable low-cost substitute in lower order (lumped) TR simulations to enable TR prevention and mitigation.

Singh, Bakhshish Preet (ORCID:0000000264751992)↗
NASA NTRS1993

Dynamics of flames near the rich-flammability limit of hydrogen-air mixtures

Flames near the rich-flammability limit of hydrogen-air mixtures are studied using a detailed, time-dependent, one-dimensional Lagrangian model. Results from the numerical simulations indicate that a steady burning velocity is not obtained for very rich hydrogen-air mixtures. As the amount of hydrogen is increased, a damped oscillation is observed in the flame and burning velocities, and then, with further increase in the amount of hydrogen, an undamped oscillation with a complex set of frequencies is observed. Simulations with a simplified one-step irreversible chemical reaction do not show these oscillations, suggesting that chemical kinetics plays a strong role in inducing these oscillations. Further analysis shows that the oscillations are due to a competition for H atoms between chain branching and chain-terminating reactions. Simulations of spherically expanding flames suggest that stretch effects (due to curvature) will cause the oscillations to occur in less rich mixtures than that observed for planar flames. The implications of these oscillations on the rich-flammability limit as well as the role of chemical kinetics in creating a fundamental flammability limit is discussed.

Kailasanath, K.↗
NASA NTRS1994

Evaluation of SSME test data reduction methods

Accurate prediction of hardware and flow characteristics within the Space Shuttle Main Engine (SSME) during transient and main-stage operation requires a significant integration of ground test data, flight experience, and computational models. The process of integrating SSME test measurements with physical model predictions is commonly referred to as data reduction. Uncertainties within both test measurements and simplified models of the SSME flow environment compound the data integration problem. The first objective of this effort was to establish an acceptability criterion for data reduction solutions. The second objective of this effort was to investigate the data reduction potential of the ROCETS (Rocket Engine Transient Simulation) simulation platform. A simplified ROCETS model of the SSME was obtained from the MSFC Performance Analysis Branch . This model was examined and tested for physical consistency. Two modules were constructed and added to the ROCETS library to independently check the mass and energy balances of selected engine subsystems including the low pressure fuel turbopump, the high pressure fuel turbopump, the low pressure oxidizer turbopump, the high pressure oxidizer turbopump, the fuel preburner, the oxidizer preburner, the main combustion chamber coolant circuit, and the nozzle coolant circuit. A sensitivity study was then conducted to determine the individual influences of forty-two hardware characteristics on fourteen high pressure region prediction variables as returned by the SSME ROCETS model.

Santi, L. Michael↗
DOE OSTI2023

Nonlocal suppression of Biermann battery magnetic-field generation for arbitrary atomic numbers and magnetization

The Biermann battery term of magnetohydrodynamics (MHD) generates a magnetic field where electron density gradients and electron temperature gradients are perpendicular to one another. Kinetic simulations and experiments have shown that the rate of magnetic-field generation is lower than Biermann when the electron mean free path becomes comparable to or greater than the temperature gradient scale length, known as the nonlocal regime. We investigate the nonlocal suppression of the Biermann term using simplified Fokker–Planck simulations covering a wide range of parameters. We provide the first fit for nonlocal Biermann suppression that has physically accurate behavior for small and large values of a suitable nonlocality parameter, valid for an arbitrary atomic number, and that includes the effect of magnetization on nonlocality. Lastly, the fit is intended to provide an approximate method to account for reduced magnetic-field generation in MHD codes and theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1985

The design of a precision pointing contol system for the Space Infrared Telescope Facility

The design and performance simulation of the Space Infrared Telescope Facility pointing and control system are described. The system design is constrained by such considerations as image stability, maneuver capability, cryogen lifetime, and structural flexibility. The primary design driver is the requirement to rapidly execute small angle reorientations of the telescope's optical axis. The flexibility of the spacecraft was simulated using a simplified multibody model which provided an approximation of the primary bending modes. The rather conventional attitude control system design of PID type with a 0.5 Hz bandwidth was enhanced to meet the small angle maneuver requirements by the use of three techniques: (1) a feedforward loop to improve the time response; (2) torque shaping to minimize structural excitation; and (3) active image stabilization to remove residual pointing error and jitter. Simulation results indicate that the system has the desired performance and can be designed using techniques and hardware well within the state-of-the-art.

Sridhar, B.↗